Enhancing wood efficiency through comprehensive wood flow analysis:Methodology and strategic insights

Wood,an essential natural resource in human civilization,remains widely used despite advances in technology and material substitution.The surge in greenhouse gas emissions and environmental concerns accentuates the need for optimizing wood utilization.Material flow analysis is a powerful tool for tracking material flows and stocks,aiding resource management and environmental decision-making.However,the full extent of its methodological dimensions,particularly within the context of the wood supply chain,remains relatively unexplored.In this study,we delve into the existing literature on wood flow analysis,discussing its primary objectives,materials involved,temporal and spatial scales,data sources,units,and conversion factors.Additionally,data uncertainty,data reconciliation and crucial assumptions in material flow analysis are highlighted in this paper.Key findings reveal the significance of wood cascading and substitution effects by replacing non-wood materials,where they can reduce greenhouse gas emissions more than the natural carbon sink of forests and wood products.The immediate impact of short-term wood cascading might not be as robust as the substitution effect,with energy substitution showcasing better results than material substitution.However,it's crucial to note that these conclusions could experience significant reversal from a long-term and global perspective.Strategies for improving wood efficiency involve maximizing material use,advancing construction technologies,extending product lifespans,promoting cascade use,and optimizing energy recovery processes.The study underscores the need for standardized approaches in wood flow analysis and emphasizes the potential of wood efficiency strategies in addressing environmental challenges.

A novel formulation of material nonlinear analysis in structural mechanics

This article demonstrates a novel approach for material nonlinear analysis.This analysis procedure eliminates tedious and lengthy step by step incremental and then iterative procedure adopted classically and gives direct results in the linear as well as in nonlinear range of the material behavior.Use of elastic moduli is eliminated.Instead,stress and strain functions are used as the material input in the analysis procedure.These stress and strain functions are directly derived from the stress-strain behavior of the material by the method of curve fitting.This way,the whole stress-strain diagram is utilized in the analysis which naturally exposes the response of structure when loading is in nonlinear range of the material behavior.It is found that it is an excellent computational procedure adopted so far for material nonlinear analysis which gives very accurate results,easy to adopt and simple in calculations.The method eliminates all types of linearity assumptions in basic derivations of equations and hence,eliminates all types of possibility of errors in the analysis procedure as well.As it is required to know stress distribution in the structural body by proper modelling and structural idealization,the proposed analysis approach can be regarded as stress-based analysis procedure.Basic problems such as uniaxial problem,beam bending,and torsion problems are solved.It is found that approach is very suitable for solving the problems of fracture mechanics.Energy release rate for plate with center crack and double cantilever beam specimen is also evaluated.The approach solves the fracture problem with relative ease in strength of material style calculations.For all problems,results are compared with the classical displacement-based liner theory.

Preliminary Research on Regional Material Flow Analysis:A Case Study of Chengyang District in Qingdao

The method ＂Material Flow Analysis （MFA）＂ is one of the effective tools to study law and quantification of material flow between economic system and ecological system. On the national level, economy-wide material flow analysis has been published for a number of countries. However, published studies on the regional or local level are still very limited and a standardized method does not exist yet. On the basis of framework of Material Flow Analysis proposed by Eurostat, the paper collected related data and analyzed material input and output for the Chengyang district in Qingdao. The results showed that DMI （Direct Material Input） and TMR （Total Material Requirement） in absolute number increased about 3.6 and 3.9 times, respectively from 1995 to 2004. Fossil fuel and mineral contributed to about 50.3%-76.3% of DMI. Imports of material increased about 5.0 times and became the most important Contributor to DMI, which showed that local economic growth was highly dependent on resources from other regions and countries. DPO （Domestic Processed Output） and TDO （Total Domestic Output） represent slow increasing trend, and DPO contributed to 22.2%-58.1% of TDO, suggesting local hidden flows were of obvious effect on TDO. The biggest component of DPO is CO2, approximately accounting for 90% of DPO. The material productivity increased 57.7% in last decade, reflecting improvement of efficiency of resources utilization in some extent. However, compared to developed countries and regions, material productivity of Chengyang district was relatively low. Therefore, in order to promote the sustainability, it is essential to develop circular economy and enhance materials productivity.

Current status and future trends for material flow analysis applications at CSC

Material Flow Analysis(MFA) is a crucial instrument for sustainable development and creating industrial ecology system.MFA studies could balance and analyze the sources,flows,and consumes of specific materials or substances.The results of MFA studies could support the strategies or decisions making for energy, resource,and waste management,especially achieving sustainable resource management.At CSC,the dynamic simulating software,STELLA,is used to develop a MFA model for scenario analysis.CSC also uses the freeware STAN 2.0 as a tool for visualizing and simulating material flows and stocks.Case studies of greenhouse gases MFA for integrated steel works are conducted.The results showed that the carbon content of hot-metal is an important hidden flow for balance analysis,and the different GHG emission scenarios and mitigation action scenarios are assessed.In addition,the Iron-making GHG I/O MFA Model,based on worldsteel Global Steel Sector Approach(GSSA),is developed for calculating the CO_2 and energy intensity of coke making,sintering,and BF processes.This MFA model was used to analyze the CO_2 reduction potential for iron-making process.The cases conducted for MFA applications at CSC were such as greenhouse gas,zinc,etc.In the future,CSC is going to develop a 'CSC Environment Management and Decision Supporting System' which combine MFA,LCA(life cycle assessment),and environment risk assessment.This supporting system expects to promoting energy efficiency and best resource use,supporting environment policymaking,creating environmental information value,etc.

Three-dimensional Analysis of Functionally Graded Piezoelectric Plate with Arbitrarily Distributed Material Properties

An orthotropic functionally graded piezoelectric rectangular plate with arbitrarily distributed material properties was studied, which is simply supported and grounded（electrically） on its four lateral edges. The state equations of the functionally graded piezoelectric material were obtained using the state-space approach, and a Peano-Baker series solution was obtained for the coupled electroelastic fi elds of the functionally graded piezoelectric plate subjected to mechanical and electric loading on its upper and lower surfaces. The influence of different distributions of material properties on the structural response of the plate was studied using the obtained solutions.

Relationships between femoral strength evaluated by nonlinear finite element analysis and BMD,material distribution and geometric morphology

Precisely quantifying the strength of the proximal femur and accurately assessing hip fracture risk would enable those at high risk to be identified so that preventive interventions could be taken.Development of better measures of femoral strength using the clinically

The Stress Analysis for Notched Specimen of Brittle Material under Plane Dead Loading

The stress distribution of notched specimen of brittle material under a plane pressure was studied using a photoelastic meth- od,When elastic deformation appeared inside the specimen,the force transferred by dowel part was triangular transverse force and frictional force on the upper surface of the sample.The quantity of the frictional force was about 31 percent of transverse force.The stress inside the sample was linear along the central cross section of the sample and there was maximum tensile stress σ_y at the tip of the notch.Basing on shearing stress deviation method,the tensile stress σ_y,σ_x and shearing stress τ_(xy) at the cen- tral sections and four adjacent cross sections were calculated.The result pointed out that σ_x and τ_(xy) were smaller than σ_y.There- fore,σ_y was the main factor for crack formation and propagation.

INCREMENTAL ANALYSIS FOR NONLINEAR RUBBER-LIKE MATERIALS BY HYBRID STRESS FINITE ELEMENT

In this paper, on the basis of the incremental Reissner variational principle.a nonlinear finite element analysis has been accomplished and a formulation of hybrid stress element has been presented for incompressible Mooney rubber-like materials. The corrected terms of the non-equilibrium force and the incompressibility deviation are considered in the formulation. The computed values of numerical example agree very closely with the exact solution.

Magnetothermal Analysis of Nanocrystallization of Amorphous and Relaxations of Nanocrystalline Materials

For a few years it has been realized that nanocrystalline phases can be formed during crystallization of amorphous alloys annealed isothermally below the crystallization temperature of usual heating experiments. Data of this transformation monitored by the measurement of magnetic susceptibility are presented. A method using a magnetic balance with electronic stabilisation and combined computer facilities is applied. Constant heating and cooling rates as well as isothermal heat treatments are used. Magnetic measurements are able to detect the onset of the transformation of amorphous NI-P alloys much earlier than was possible with differential scanning calorimetry. The transformation kinetics can be analyzed by means of the Avrami plot based on the Johnson-Mehl-Avrami equation. The kinetics of solid state reactions in the nanostructured material can be investigated similarly. Formation of a Ni-phase in a nanostructured Hf-Ni alloy could be detected in a very early stage, where calorimetric methods are not sensitive. Segregation phenomena could be detected from the experiments even after long time. The sensitivity of the applied method is not dependent on the heating rate as the sensitivity of scanning calorimetry is.

SHAKEDOWN ANALYSIS OF SHELL STRUCTURES OF KINEMATIC HARDENING MATERIALS

It is of great practical importance to analyze the shakedown of shell structures under cyclic loading, especially of those made of strain hardening materials.In this paper, same further understanding of the shakedown theorem for kinematic hardening materials has been made, and it is applied to analyze the shakedown of shell structures Though the residual stress of a real stale is related to plastic strain, the time-independent residual stress field as we will show in the theorem may be unrelated to the time-independent kinematically admissible plastic strain field For the engineering application, it will lie much more convenient to point this out clearly and definitely, otherwise it will be very difficult. Also, we have proposed a new method of proving this theorem.The above theorem is applied to the shakedown analysis of a cylindrical shell with hemispherical ends. According to the elastic solution, various possible residual sfcss and plastic strain Jlelds, the shakedown analysis of the structure can be reduced to a mathematical programming problem.The results of calculation show that the shakedown load oj strain hardening materials is about 30-40% higher than that of ideal plastic materials. So it is very important to consider the hardening of materials in the shakedown analysis,for it can greatly increase the structure design capacity, and meanwhile provide ascicntific basis to improve the design of shell structures.

Chemical Analysis of Magnesia and Magnesia-Alumina Refractory Materials——Gravimetric method for determination of loss on ignition

1 Scope This standard specifies the gravimetric method for determination of loss on ignition.

Chemical Analysis of Magnesia and Magnesia-Alumina Refractory Materials——Flame atomic absorption spectrometric method for determination of calcium oxide content

1 Scope This standard specifics the determination of calcium oxide coutent by flame atomic absorption spectrometric method.

Evaluation and Selection of Sealants and Fillers Using Principal Component Analysis for Cracks in Asphalt Concrete Pavements

The objective of this paper was to develop a comprehensive evaluation method and index to evaluate the performance of sealants and fillers for cracks in asphalt concrete pavements using the method of principal component analysis. The performance experiments including cone penetration, softening point, flow, resilience and tension at low temperature respectively were conducted by reference of ASTM D5329 for eight sealants and fillers often used in China. There by a principal component model was developed and weight of every index was calculated. The experimental results show that there are significantly different performances for sealants and fillers often used in China. Principal component analysis is an objective method that evaluates and selects the performance of sealants and fillers for cracks in asphalt concrete pavements.

Compositional and Structural Difference of Fulvic Acid from Black Soil Applied with Different Organic Materials: Assessment After Three Years

Knowledge of different effects of various organic materials on soil humic substance is important for both environmental safety and sustainable agriculture.A pot experiment was conducted at Jilin Agricultural University,Jilin Province in northeast China to discover the influence of herb residue,animal excrement,woody residue,animal remnant on fulvic acid（FA） composition and structure using differential thermal analysis-thermogravimetric（DTA-TG）,fourier transform infrared spectroscopy（FTIR） and elemental analysis.DTA-TG showed the range of peak temperature in the first exothermic reaction increased following the trend： CK〉herb residue〉animal excrement〉woody residue=animal remnant,and the most weight loss was observed in animal excrement.Moreover,the second exothermic reaction of CK-and animal excrement-FA was presented as double peaks,the order of weight loss in that area was animal remnant〉CK〉woody residue〉animal excrement〉herb residue.According to FTIR,herb residue displayed higher adsorption intensity at 2 950,1 420,1 240 and 1 030 cm-1,animal excrement was in reverse.At the same time,herb residue-and animal excrement-FA had an absorption peak at 1 720 cm-1,while other organic materials didn＇t have this peak.As elemental analysis showed,FA isolated from various treatments was significantly distinct.It was clearly shown from our results that FA composition and structure in amended soils may be affected in different ways and at various extents on dependence of the nature and origin of amendment.

Influence of the gassing materials on the dielectric properties of air

Influence of the gassing materials, such as PA6, PMMA, and POM on the dielectric properties of air are investigated. In this work, the fundamental electron collision cross section data were carefully selected and validated. Then the species compositions of the air–organic vapor mixtures were calculated based on the Gibbs free energy minimization. Finally, the Townsend ionization coefficient, the Townsend electron attachment coefficient and the critical reduced electric field strength were derived from the calculated electron energy distribution function by solving the Boltzmann transport equation. The calculation results indicated that H;O with large attachment cross sections has a great impact on the critical reduced electric field strength of the air–organic vapor mixtures. On the other hand, the vaporization of gassing materials can help to increase the dielectric properties of air circuit breakers to some degree.

Analysis of Doppler Radar Data of the Largest Snow Process since Winter

[Objective] Characteristics of Doppler radar data of the largest snow process since winter in Chengde City on February 26,2011 were discussed.[Method] By dint of reflection rate factors,radial velocity,and VWP product of Doppler radar in C wave in Chengde of Hebei Province,and coupled with large scale of circulation situation,the largest snow process since the winter in Chengde City on February 26,2011 was discussed.[Result] The echo intensity of snow was weak.If there was certain range of 30 dBz echo and was stable,there might be strong snow.The warm advection,convection and warm and wet air climbing over the thin cold cushion in the lower layer was the main reason of the precipitation.The structure of 'cattle eye' and the torrent in the lower air provided incessant water vapor for the generation of strong precipitation.When the wind in the vertical direction changed,there was wind speed divergence,which indicated that the precipitation weakened and stopped.The existence of warm advection and shear layer was the essential reason for the maintenance of precipitation.The 'ND' area in the middle layer and the northwest wind at any height indicated the end of precipitation.[Conclusion] The study provided theoretical basis for the forecast of strong snow.

On the stress–strain states of cellular materials under high loading rates

A virtual Taylor impact of cellular materials is analyzed with a wave propagation technique, i.e. the Lagrangian analysis method, of which the main advantage is that no pre-assumed constitutive relationship is required. Time histories of particle velocity, local strain, and stress profiles are calculated to present the local stress-strain history curves, from which the dynamic stress-strain states are obtained. The present results reveal that the dynamic-rigid-plastic hardening （D-R-PH） material model introduced in a previous study of our group is in good agreement with the dynamic stress-strain states under high loading rates obtained by the Lagrangian analysis method. It directly reflects the effectiveness and feasibility of the D-R-PH material model for the cellular materials under high loading rates.

Exploring the potential for improving material utilization efficiency to secure lithium supply for China's battery supply chain

Lithium-ion battery(LIB)is the key technology for climate change mitigation.The sustainability of LIB supply chain has caused widespread concern since the material utilization efficiency of LIB supply chain has not been well investigated.This study aims to fill this research gap by conducting a dynamic material flow analysis of lithium in China from 2015 to 2021.Results indicate that within the temporal boundary,lithium flow and in-use stock grew significantly in China due to the rapid development of the EV market,with lithium flow in domestic production of basic chemicals increasing by 614%to 100 kt,end-use consumption increasing by 160%to 35 kt,and in-use stock increasing by 62%to 195 kt.China has been a net importer of lithium,of which cumulative imports and exports were 343 kt and 169 kt,respectively.In addition,103 kt of lithium was converted to inventories or was lost during the processing from 2015 to 2021.By optimizing inventory and processing,developing substitutes for lithium for non-battery applications,and improving lithium recycling,China's net import dependency of lithium could be reduced from 27%-86%to 0%-16%.Our study demonstrates that it is urgent to improve material utilization efficiency so that the lithium resource supply can be secured.

Estimation and prediction of plastic waste annual input into the sea from China

Marine plastic debris has been a pervasive issue since the last century, and research on its sources and fates plays a vital role in the establishment of mitigation measures. However, data on the quantity of plastic waste that enters the sea on a certain timescale remain largely unavailable in China. Here, we established a model using material flow analysis method based on life cycle assessment to follow plastic product from primary plastic to plastic waste with statistical data and monitoring data from accurate sources. This model can be used to estimate and forecast the annual input of plastic waste into the sea from China until 2020. In 2011, 0.547 3-0.751 5 million tons of plastic waste entered the seas in China, with a growth rate of 4.55% per year until 2017. And the amount will decrease to 0.257 1 to 0.353 1 million tons in 2020 under the influence of governmental management. The amount of plastic waste discharged from coastal areas calculated in this study was much larger than that from river, thus it is suggested to strengthen the governance and control of plastic waste in coastal fishery activities in China in order to reduce the amount of marine plastic waste input.

Sustainable Intensification of Cultivated Land Use and Its Influencing Factors at the Farming Household Scale: A Case Study of Shandong Province, China

Promoting the sustainable intensification of cultivated land use(SICL) has become crucial for ensuring a sufficient supply of grain and important agricultural products, as well as for the sustainable use of resources. Taking widely used areas of Shandong Province in China as examples, an analytical scale and level framework for SICL is constructed in this study. It measures the level of SICL through material flow analysis, constructs Tobit models to analyze the influencing factors of SICL at the farming household scale,and analyzes the transition mechanisms of SICL. The results show that the overall level of SICL in Shandong Province is low, and the spatial distribution is uneven. There are relatively more farmers participating in unsustainable intensification than in medium or low levels of SICL, with farmers working at a high level of SICL making up the smallest proportion. The factors that determine the level of SICL at which farmers work vary significantly. More male farmers operate at a low SICL level than female farmers, while females outnumber males at a high SICL level. This is mainly related to the regional distribution of age and population. Meanwhile, with larger cultivated land areas, there is a lower degree of land fragmentation, with a higher level of SICL corresponding to a smaller distance to the nearest town closer within 1–5 km from the town center. We can see the level of SICL and its processes themselves are closely related to time and space scales. Based on the above analysis, it is necessary to clarify the standard processes of SICL to adapt them to local conditions. This includes instructing managers on how to improve resource utilization, increase the sustainable development of cultivated land and establish a comprehensively efficient and functional SICL mechanism. The sustainable intensification of cultivated land use and its specific application in the new era are conducive to enriching the frontier theories and methodology of sustainable development, and are of great significance to the advancement of green agriculture and the decision-making of rural high-quality development.