A Simulation Research on the Grid-Connected Control Technology of Single-Phase Inverters Based on MATLAB

This paper primarily discusses the main circuit of single-phase inverter circuits.It begins by introducing the research context and the significance of the subject,then discusses the topology of grid-connected single-phase inverter circuits,continues by discussing the control strategy for grid-connected single-phase inverter circuits,realizes a sinusoidal pulse width modulation(SPWM)signal generation circuit and an inverse control algorithm program,and finally ensures good output waveform and fast dynamic response.In view of the hysteresis feature of the grid voltage’s synchronous signal sampling circuit,the acquisition function in digital signal processing(DSP)control chips is applied,and the reasons for the hysteresis phenomenon are thoroughly investigated.The reliability of the SPWM control algorithm is revealed through the results.

Matlab/Simulink Based Dynamic Simulation System for Distance Protection

To observe the inner operating process of distance protection,a Matlab/Simulink based dynamic simulation system for microprocessor-based distance protection is designed in this paper.As a modularized design,the simulation system is composed of several modules such as fault transient calculation,startup,Fourier algorithm,phase selection,impedance computing and impedance comparison etc.Some typical simulation cases,which focus on the main factors affecting distance relay's operation,have been simulated with the system.Simulation results show that the system is able to demonstrate the dynamic behaviors of distance protection under different operating conditions.

MPPT for Hybrid Energy System Using Gradient Approximation and Matlab Simulink Approach

This paper applies new maximum-power-point tracking （MPPT） algorithm to a hybrid renewable energy system that combines both Wind-Turbine Generator （WTG） and Solar Photovoltaic （PV） Module （SPVM）. In this paper, the WTG is a direct-drive system and includes wind turbine, three-phase permanent magnet synchronous generator, three-phase full bridge rectifier, and buck-bust converter, while the SPVM consist of solar PV modules, buck converter, maximum power tracking system for both systems, and load. Several methods are applied to obtain maximum performances, the appropriate and most effective method is called gradient-approximation method for WTG approach, because it enables the generator to operate at variable wind speeds. Furthermore MPPT also is used to optimized the achieved energy generated by solar PV modules.Matlab / Simulink approach is used to simulate, discuss, and optimized the generated power by varying the duty cycle of the converters, and tip speed ratio of the WTG system.

Groove modeling and digital simulation for intersecting structures of circular tubes based on coplanarity of vectors

In order to establish the groove model for intersecting structures of circular tubes,mathematical model of the intersecting line is established by the method of analytic geometry,and parametric equations are thus determined.The dihedral angle,groove angle and actual cutting angle for any position of the intersecting line are derived as well.In order to identify groove vectors for two pipes,a new analytical method,i.e.coplanarity of vectors,is further proposed to complete the groove model.The established model is virtually verified by programming and simulation calculation in the MATLAB environment.The results show that groove vectors of intersecting structures simulated by MATLAB are consistent with the theoretical groove model,indicating that the theoretical groove model established in this paper is accurate,and further proves that the proposed coplanarity of vectors for solving groove vectors is correct and feasible.Finally,a graphical user interface(GUI)is developed by MATLAB software to independently realize functions such as model drawing,variable calculation and data output.The research outcome provides a theoretical foundation for the actual welding of circular intersecting structures,and lays an essential basis for weld bead layout and path planning.

基于Matlab的可编程逻辑微机保护的研究

目前在低压微机保护装置中,基于可编程逻辑的微机保护的应用是越来越多。这种微机保护平台,提高了微机保护装置的可靠性、灵活性、实用性、可扩展性和可移植性,大大缩短了产品的开发周期,同时有效解决了微机保护装置的工程化问题。在分析了目前常见的可编程逻辑微机保护之后,提出了一种新的基于Matlab/Simulink工具软件和DSP相结合的可编程逻辑微机保护的设想,这种方法预期有更高的灵活性,更短的产品开发周期。

Simulation of a Triple Inverted Pendulum Based on Fuzzy Control

The inverted pendulum is a classic problem in dynamics and control theory and is widely used as a benchmark for testing control algorithms. This paper studies the use of fuzzy control method to study the stability control problem of a triple inverted pendulum system. By the linear model of the system, the feedback weight matrix of the LQR optimal control and the feedback parameters of the linear optimal control are designed to determine the parameters of the fuzzy controller. The simulation results show that the proposed method can achieve the stability control of the three stage inverted pendulum, and has good dynamic performance with simple parameter selection.

Tripartite evolutionary game and simulation study on enterprise green technology innovation

By constructing the evolutionary game model among the government,enterprises and consumers,the paper analyzes the condition that the profit and loss relationship of the game subjects and their behavior strategies reach the stable state in the green technology innovation system,and uses MATLAB to conduct data simulation analysis.The results show that the government,enterprises and consumers have path-dependent behavior choices.The larger the government incentive coefficient and subsidy coefficient is not the better,but the larger the subsidy and subsidy coefficient will hinder the green technology innovation.Government punitive measures will promote green technology innovation,but high innovation subsidies will restrain the government’s environmental regulation.Therefore,the government should further improve environmental regulation policies,increase enterprises’enthusiasm for green technology innovation and consumers’acceptance of green products,and promote the development of green technology innovation.

Edge detection and mathematic fitting for corneal surface with Matlab software

AIM：To select the optimal edge detection methods to identify the corneal surface,and compare three fitting curve equations with Matlab software. METHODS：Fifteen subjects were recruited. The corneal images from optical coherence tomography（OCT）were imported into Matlab software. Five edge detection methods（Canny,Log,Prewitt,Roberts,Sobel）were used to identify the corneal surface. Then two manual identifying methods（ginput and getpts）were applied to identify the edge coordinates respectively. The differences among these methods were compared. Binomial curve（y=Ax2＋Bx＋C）,Polynomial curve [p（x）=p1xn＋p2x（n-1）＋....＋pnx＋pn＋1] and Conic section（Ax2＋Bxy＋Cy2＋Dx＋Ey＋F=0）were used for curve fitting the corneal surface respectively. The relative merits among three fitting curves were analyzed. Finally,the eccentricity（e）obtained by corneal topography and conic section were compared with paired t-test. RESULTS：Five edge detection algorithms all had continuous coordinates which indicated the edge of the corneal surface. The ordinates of manual identifying were close to the inside of the actual edges. Binomial curve was greatly affected by tilt angle. Polynomial curve was lack of geometrical properties and unstable. Conic section could calculate the tilted symmetry axis,eccentricity,circle center,etc. There were no significant differences between ＇e＇ values by corneal topography and conic section（t=0.9143,P=0.3760 〉0.05）.CONCLUSION：It is feasible to simulate the corneal surface with mathematical curve with Matlab software. Edge detection has better repeatability and higher efficiency. The manual identifying approach is an indispensable complement for detection. Polynomial and conic section are both the alternative methods for corneal curve fitting. Conic curve was the optimal choice based on the specific geometrical properties.

基于Matlab的比率制动式变压器纵差保护仿真研究

电力变压器作为现代电网中最重要的设备之一,承担着电压变换的重要任务,因此对变压器保护的选择性、速动性、灵敏性和可靠性有很高的要求。为了深入分析变压器在故障时的暂态情况,改进现有变压器保护中的不足,该文基于Matlab嵌入式函数模块型,构建了变压器故障和正常运行时的仿真模型。通过模拟变压器内外部故障,使研究者直观地观察到电力系统从运行状态到故障发生期间电气特征量的变化特征以及保护装置中每个元件处理和动作的过程。该仿真模型的研发周期短,研发效率高,便于为后续设计可靠的继电保护产品提供重要的实验平台,可有效解决利用物理模型开发继电保护产品的实验成本高、效率低、灵活性和通用性差等缺点。

Modelling and Simulation of an Ohmic Heating Process

Ohmic Heating (OH) is one of the emerging thermal technologies used in food processing which can produce rapid and uniform heating with close to 100% energy transfer efficiency. Although mathematical modelling for OH processes has been studied by many researchers in recent years, systematic simulations of OH have not been developed for model-based control of the processes. In this paper, mathematical model for a Colinear Ohmic Heater is presented, analyzed, and studied based on the selected configuration. A numerical solution for the mathematical equations has been defined and proposed. MATLAB/Simulink model is hence developed and validated against the available data. Simulation results have shown that MATLAB/Simulink model can produce robust outputs at low computational costs with an accuracy of up to 99.6% in comparison to the analytical solution. This model can be used in further studies for analysis of the OH processes and development of advanced controllers.

Evaluation of the Performance of Lithium-Ion Accumulators for Photovoltaic Energy Storage

In a context of climate change exacerbated by the increasing scarcity of fossil fuels, renewable energies, in particular photovoltaic solar energy, offer a promising alternative. Solar energy is non-polluting, globally available and the most widely distributed resource on Earth. However, the intermittency of this energy source considerably limits its expansion. To solve this problem, storage techniques are being used, in particular, electrochemical storage using lithium-ion batteries. In this article, we will evaluate the performance of lithium-ion batteries when integrated into a photovoltaic grid. To do this, modelling and simulation of a photovoltaic system connected to a lithium-ion battery storage system will be carried out using MATLAB/Simulink software. A diagnostic of the energy consumption of the Kaya Polytechnic University Centre will be carried out, and the data will then be used in the simulator to observe the behaviour of the PV-Lion system. The results obtained indicate that lithium-ion batteries can effectively meet the centre’s energy demand. In addition, it was observed that lithium-ion batteries perform better under high energy demand than the other battery technologies studied. Successive storage systems with the same capacity but different battery technologies were compared. It was found that these storage systems can handle a maximum power of 4 × 105 W for lead-acid batteries, 6.5 × 105 W for nickel-cadmium batteries, 8.5 × 105 W for nickel-metal-hydride batteries, and more than 10 × 105 W for lithium-ion technology.

数控切削性能的Fuzzy-PID控制算法的设计与仿真

随着零件加工精度的日益提高及外界干扰因素的不断增加,传统PID控制的数控加工过程已不能满足目前切削性能的需求,如何使数控机床在加工中仍然保持优越的切削性能是目前制造领域研究的热点问题之一。根据数控切削加工系统的组成结构,建立了切削系统的数学模型。通过分析单位阶跃响应的误差曲线,归纳了PID参数自调整的模糊规则,并完成了一套与切削系统相匹配的Fuzzy-PID算法的设计。经动态性能、抗干扰性能和鲁棒性能的仿真实验分析,结果表明与传统PID算法相比,Fuzzy-PID算法应用于切削系统中具有更良好的品质。

Adaptive compensating method for Doppler frequency shift using LMS and phase estimation

The novel compensating method directly demodulates the signals without the carrier recovery processes, in which the carrier with original modulation frequency is used as the local coherent carrier. In this way, the phase offsets due to frequency shift are linear. Based on this premise, the compensation processes are： firstly, the phase offsets between the baseband neighbor-symbols after clock recovery is unbiasedly estimated among the reference symbols; then, the receiving signals symbols are adjusted by the phase estimation value; finally, the phase offsets after adjusting are compensated by the least mean squares （LMS） algorithm. In order to express the compensation processes and ability clearly, the quadrature phase shift keying （QPSK） modulation signals are regarded as examples for Matlab simulation. BER simulations are carried out using the Monte-Carlo method. The learning curves are obtained to study the algorithm＇s convergence ability. The constellation figures are also simulated to observe the compensation results directly.

双闭环调速工程设计仿真建模及应用研究

为提高运动控制系统的教学效果,本文阐述了直流双闭环调速系统仿真模型的建立方法,利用这一模型可以完成除运动控制系统按教学大纲规定的实验外,还可以完成其他一些研究性实验。这种方法具有实验室建设成本低、实验时间自由、实验开放性好、参数调整方便、实验效果佳等几大优点,在我国高校自动化专业教学中推广应用这种方法,对于提高教学质量有着十分积极的意义。

SVPWM的算法及仿真研究

在分析空间矢量脉宽调制(SVPWM)技术原理的基础上,详细推导了SVPWM算法,并对传统算法进行了过调制处理,使算法得以完善。在MATLAB/Simulink环境下建立了SVPWM控制的三相电压型逆变器仿真模型。仿真结果表明该算法的正确性和可行性。

A new complete model of switch-mode plasma cutting power supply

A complete model of switch-mode plasma cutting power supply and its simulation are developed. The full bridge isolated pulse width modulation (PWM) buck converter in continuous conduction mode (CCM) for high watt plasma power supply is approached. Reduced ripple current and improved power factor are achieved in the plasma power supply. With a PID control strategy, circuit responses become more stable and faster with low overshoot during load and current changing. The converter achieved high efficiency under 3 to 15kW load conditions.

Performance Analysis of a Woodchip Downdraft Gasifier： Numerical Prediction and Experimental Validation

The study deals with a multi-faceted theoretical approach, symbolic, analytical and numerical, based on the chemical equilibrium assumption, addressed at predicting the performance trends of downdrafi wood-gasification processes so to assess the optimal ranges of input parameters, in particular the equivalence ratios, suitable to achieving the highest cold gas efficiencies whilst keeping the more the possible tar-free the produced bio-syngas. The time-steady, zero-dimensional model has been developed within MATLAB （the computing language and interactive environment from Matrix Laboratory） and solved by enforcing the constraints posed by the equilibrium constants in relation to two reactions, gas-water shift and methanation. Particular care is devoted toward verifying the real attainment of the equilibrium condition, as attested by an actual presence of products from the equilibrium reactions together with a zero difference AE between the energy flows entering and exiting the system, an issue often overlooked. With respect to other similar theoretical approaches, the numerical model, assisted by the symbolic counterpart for better interpretation and intrinsic validation of results, shows a distinct advantage in predicting rather accurately the syngas composition for varying gasification temperatures, as attested by cross comparisons with experimental data directly taken on an instrumented, dedicated, small-scale downdraft gasifier operational at DIME/SCL （the Savona Combustion Laboratory of DIME, the Dept. of Mechanical, Energy, Management and Transportation Engineering of Genova University）. The behavior of cold gas efficiency clearly points out that, from an energy conversion point of view, the optimal gasification temperatures turn out comprised between 900 ℃ and 1,000 ℃： this range is indeed characterized by the highest concentrations in the energy-rich syngas components CO and H2. For higher temperatures, as induced by higher air-to-fuel ratios, the progressive oxidation of above components, together with increasing nitrogen levels, would decrease the bio-syngas heat values.

Positioning-control Based on Trapezoidal Velocity Curve for High-precision Basis Weight Control Valve

Traditionally, basis weight control valve is driven by a constant frequency pulse signal. Therefore, it is difficult for the valve to match the control precision of basis weight. Dynamic simulation research using Matlab/Simulink indicates that there is much more overshoot and fluctuating during the valve-positioning process. In order to improve the valve-positioning precision, the control method of trapezoidal velocity curve was studied. The simulation result showed that the positioning steady-state error was less than 0.0056%, whereas the peak error was less than 0.016% by using trapezoidal velocity curve at 10 positioning steps. A valve-positioning precision experimental device for the stepper motor of basis weight control valve was developed. The experiment results showed that the error ratio of 1/10000 positioning steps was 4% by using trapezoidal velocity curve. Furthermore, the error ratio of 10/10000 positioning steps was 0.5%. It proved that the valve-positioning precision of trapezoidal velocity curve was much higher than that of the constant frequency pulse signal control strategy. The new control method of trapezoidal velocity curve can satisfy the precision requirement of 10000 steps.

Research of Pure Electric Ferry System and Its Short-Circuit Protection and Calculation

System control and safety reliability are important links of the marine DC (Direct Current) power system. The simulationmodel is built by Matlab/Simulink, the battery and super-capacitor are supplied to the system through a three-phase interleaved DC/DCconverter, the fuse and disconnector switch combination are used as the protection device, and the short-circuit point is set betweeneach branch and the DC distribution board, performing short-circuit simulation. This paper also proposes a short-circuit calculationmethod for super-capacitors based on the simplified model of series RC (Resistors & Capacitors), and verifies its correctness throughsimulation data. The results show that the introduction of a three-phase interleaved DC/DC converter reduces the current ripple andmakes the system control more convenient;short-circuit calculation and simulation have determined the short-circuit withstandcapability of the DC distribution board, and verified the feasibility of the fuse selection method and the short-circuit calculation methodof the super-capacitor. This provides reliable verification for the application and calculation of the actual project.

Simulation of Adaptive Control Strategy for Electrical Discharge Machining Process

Electrode down-time is an important factor affecting the efficiency and stability of electrical discharge machining(EDM) process. In the research, a way of simulating the regulation of the electrode down-time in an EDM adaptive control system has been studied. All the simulations are performed on Matlab. The simulation results demonstrate that this adaptive controller by regulating electrode down-time can direct the gap state to follow the specified reference gap state with or without disturbances. Finally, the adaptive control scheme is also validated by experiments. The significance of the simulation of an EDM adaptive control system lies on the fact that it provides a convenient way to guide the actual production and provides a new study method for the research of EDM control strategy with no regard of experimental conditions.