Mechanical Property and Microstructure of Cement Mortar with Carbonated Recycled Powder

Carbonated recycled powder as cementitious auxiliary material can reduce carbon emissions and realize high-quality recycling of recycled concrete.In this paper,microscopic property of recycled powder with three carbonation methods was tested through XRD and SEM,the mechanical property and microstructure of recycled powder mortar with three replacement rates were studied by ISO method and SEM,and the strengthening mechanism was analyzed.The results showed that the mechanical property of recycled powder mortar decreased with the increasing of replacement rate.It is suggested that the replacement rate of recycled powder should not exceed 20%.The strength index and activity index of carbonated recycled powder mortar were improved,in which the flexural strength was increased by 27.85%and compressive strength was increased by 20%at the maximum.Recycled powder can be quickly and completely carbonated,and the improvement effect of CH pre-soaking carbonation was the best.The activity index of carbonated recycled powder can meet the requirements of Grade II technical standard for recycled powder.Microscopic results revealed the activation mechanism of carbonated recycled powder such as surplus calcium source effect,alkaline polycondensation effect and carbonation enhancement effect.

Effect of heat treatment on microstructure and mechanical property of Ti-steel explosive-rolling clad plate

The effect of heat treatment on microstructure and mechanical properties of the Ti-steel explosive-rolling clad plate was elaborated by optical microscopy （OM）, scanning electron microscopy （SEM）, X-ray diffraction （XRD）, transmission electron microscopy （TEM）, micro-hardness test and shear test. The composites were subjected to heat treatment at temperature of 650-950 ~C for 60 min. The results show that the heat treatment process results in a great enhancement of diffusion and microstructural transformation. The shear strength decreases as the treatment temperature increases. Heated at 850 ℃ or below, their shear strength decreases slowly as a result of the formation of TiC in the diffusion interaction layer; while at the temperature of 850 ℃ or above, the shear strength decreases obviously, which is the consequence of a large amount of Ti-Fe intermetaUics （Fe2Ti/FeTi） along with some TiC distributing continuously at diffusion reaction layer.

Mixed grain structure and mechanical property anisotropy of AZ40 magnesium alloy bar with diameter of 160 mm

The mixed grain structure and mechanical property anisotropy of AZ40 magnesium alloy bar with a diameter of 160 mm manufactured by ＂multi-direction forging（MDF） ＋ extrusion ＋ online cooling＂ technique were investigated by optical microscopy（OM）, scanning electron microscopy（SEM）, X-ray diffraction macro-texture measurement and room temperature（RT） tensile test. The results show that mixed grain structure is caused by the micro-segregation of Al in semi-continuous casting ingot. Homogenization of（380 °C, 8 h） ＋（410 °C, 12 h） cannot totally eliminate such micro-segregation. During MDF and extrusion, the dendrite interiors with 3%-4% Al（mass fraction） transform to fine grain zones, yet the dendrite edges with about 6% Al transform to coarse grain zones. XRD macro-textures of the outer, R/2 and center show typical fiber texture characteristics and the intensity of [0001]//Ra D orientation in the outer（11.245） is about twice as big as those in the R/2（6.026） and center（6.979）. The as-extruded AZ40 magnesium alloy bar has high elongation（A） and moderate ultimate tensile strength（Rm） in both extrusion direction（ED） and radius direction（Ra D）, i.e., A of 19%-25% and Rm of 256-264 MPa; however, yield strength（Rp0.2） shows anisotropy and heterogeneity, i.e., 103 MPa in Ra D, 137 MPa in ED-C（the center） and 161 MPa in ED-O（the outer）, which are mainly caused by the texture.（155 °C, 7 h） ＋（170 °C, 24 h） aging has no influence on strength and elongation of AZ40 magnesium bar.

Effect of thermal stabilization on microstructure and mechanical property of directionally solidified Ti-46Al-0.5W-0.5Si alloy

Effect of thermal stabilization on the microstructure and mechanical property of directionally solidified Ti-46Al-0.5W-0.5Si （mole fraction, %） alloy was investigated. The specimens were thermal stabilized for different time （t） and directionally solidified at a constant growth rate of 30 μm/s and temperature gradient of 20 K/mm. Dependencies of the primary dendritic spacing （λ1）, secondary dendritic spacing （λ2）, interlamellar spacing （λL） and microhardness （HV） on holding time were determined. The values of the λ1, λ2 and λL increase with the increase of t, and the value of HV decreases with the increase of t. The increase of t is helpful to obtain a good directional solidification structure. However, it reduces the mechanical property of the directionally solidified TiAl alloy. The optimized value of t is about 30 min.

Influence of Li addition on mechanical property and aging precipitation behavior of A1-3.5Cu-1.5Mg alloy

The influence of Li addition on mechanical property and aging precipitation behavior of Al-3.5Cu-1.5Mg alloy was investigated by tensile test,scanning electron microscopy（SEM）,transmission electron microscopy（TEM） and high resolution transmission electron microscopy（HRTEM）.The results show that the tensile strength can be significantly improved with the slightly decreased ductility and the form of fracture morphology is converted from ductile fracture into ductile/britde mixed fracture by adding 1.0%Li.Besides,the peak aging time at 185 ℃ is delayed from 12 to 24 h and the main precipitation phase S（Al2CuMg） is converted into S＇（Al2CuMg）＋δ（Al3Li）,while the formation of S＇（Al2CuMg） is delayed.

Low temperature mechanical property of AZ91D magnesium alloy fabricated by solid recycling process from recycled scraps

Low temperature mechanical properties of AZ91D magnesium alloy fabricated by solid recycling process from recycled scraps were studied. Various microstructural analyses were performed using optical microscopy （OM） and scanning electron microscopy （SEM）. The recycled specimens consist of fine grains due to dynamic recrystallization and the interfaces of original individual scraps are not identified. Tensile tests were performed at a strain rate of 5 x 10 3 s 1 at room temperature （27 ~C）, -70, -100 and 130 ~C, respectively. Ultimate tensile strength of the specimens increases slightly with decreasing the tensile temperature, and elongation to failure decreases with decreasing the tensile temperature. The tensile specimens at -130 ~C show the highest ultimate tensile strength of 360.65 MPa and the lowest elongation to failure of 5.46%. Impact tests were performed at room temperature （27 ~C）, -70 and -130 ~C, respectively. Impact toughness decreases with decreasing the impact temperature. The impact specimens at -130 ~C show the lowest impact toughness of 3.06 J/cm2.

Effects of Gd on microstructure and mechanical property of ZK60 magnesium alloy

Microstructures and phase compositions of as-cast and extruded ZK60-xGd （x=0-4） alloys were investigated. Meanwhile, the tensile mechanical property was tested. With increasing the Gd content, as-cast microstructure is refined gradually. Mg-Zn-Gd new phase increases gradually, while MgZn2 phase decreases gradually to disappear. The second phase tends to distribute along grain boundary by continuous network. As-cast tensile mechanical property is reduced slightly at ambient temperature when the Gd content does not exceed 2.98%. After extrusion by extrusion ratio of 40 and extrusion temperature of 593 K, microstructure is refined further with decreasing the average grain size to 2 μm for ZK60-2.98Gd alloy. Broken second phase distributes along the extrusion direction by zonal shape. Extruded tensile mechanical property is enhanced significantly. Tensile strength values at 298 and 473 K increase gradually from 355 and 120 MPa for ZK60 alloy to 380 and 164 MPa for ZK60-2.98Gd alloy, respectively. Extruded tensile fractures exhibit a typical character of ductile fracture.

Mechanical property of artificial methane hydrate under triaxial compression

Methane production from hydrate reservoir may induce seabed slide and deformation of the hydrate-bearing strata.The research on mechanical properties of methane hydrate is considered to be important for developing an efficient methane exploitation technology.In this paper,a triaxial test system containing a pressure crystal device was developed with the conditions to stabilize the hydrate.A series of triaxial shear tests were carried out on artificial methane hydrate specimen.In addition,mechanical characteristics of methane hydrate were studied with the strain rates of 0.1 and 1.0 mm/min,respectively,under the conditions of different temperatures（T =-5,-10,and-20 ℃） and confining pressures（P = 0,5,10,15,and 20 MPa）.The preliminary results show that when the confining pressure was less than 10 MPa,the increase of confining pressure leaded to the enhancement of shear strength.Furthermore,the decreasing temperature and the increasing strain rate both caused the increase in shear strength.

Effect of Trace La Addition on the Microstructure and Mechanical Property of As-cast ADC12 Al-Alloy

The effects of addition of La on the microstructure of as-cast ADC12 A1-Alloy were investigated by using optical microscope （OM）, X-ray diffraction （XRD）, scanning electron microscope （SEM）, and energy disperse spectroscopy （EDS）. The experimental results showed that the a-A1 and eutectic Si crystals were modified with the addition of 0.3 wt% La. The eutectic Si crystals showed a granular distribution. At the same time, the alloy possessed the best mechanical property. When more than 0.3 wt% La was added to ADC12 aluminum alloy, the microstructure of as-cast alloy was coarsening gradually with the increase of the content of La and the mechanical property decreased. The effect of rare earth La which was added in ADC 12 A1-Alloy for up to 0.9 wt% had been investigated in this study. The dendrites ofADC12 Al-alloy was refined obviously and the morphology of Si crystals showed a particle structure when the addition of La reached 0,3 wt%. Besides, the acicular La-rich intermetallics in the alloy deteriorated the mechanical property of alloy： To avoid this unwanted phase, the amount of added rare earth La must be less than 0.6 wt%.

Microstructure and mechanical property of additively manufactured NiTi alloys:A comparison between selective laser melting and directed energy deposition

NiTi shape memory alloy(SMA)with nominal composition of Ni 50.8 at%and Ti 49.2 at%was additively manufactured(AM)by selective laser melting(SLM)and laser directed energy deposition(DED)for a comparison study,with emphasis on its phase composition,microstructure,mechanical property and deformation mechanism.The results show that the yield strength and ductility obtained by SLM are 100 MPa and 8%,respectively,which are remarkably different from DED result with 700 MPa and 2%.The load path of SLM sample presents shape memory effect,corresponding to martensite phase detected by XRD;while the load path of DED presents pseudo-elasticity with austenite phase.In SLM sample,fine grain and hole provide a uniform deformation during tensile test,resulting in a better elongation.Furthermore,the nonequilibrium solidification was studied by a temperature field simulation to understand the difference of the two 3D printing methods.Both temperature gradient G and growth rate R determine the microstructure and phase in the SLM sample and DED sample,which leads to similar grain morphologies because of similar G/R.While higher G×R of SLM leads to a finer grain size in SLM sample,providing enough driving force for martensite transition and subsequently changing texture compared to DED sample.

Mechanical property and biological behaviour of additive manufactured TiNi functionally graded lattice structure

Bio-inspired porous metallic scaffolds have tremendous potential to be used as artificial bone substitutes.In this work,a radially graded lattice structure (RGLS),which mimics the structures of natural human bones,was designed and processed by laser powder bed fusion of martensitic Ti-rich TiNi powder.The asymmetric tension-compression behaviour,where the compressive strength is significantly higher than the tensile strength,is observed in this Ti-rich TiNi material,which echoes the mechanical behaviour of bones.The morphologies,mechanical properties,deformation behaviour,and biological compatibility of RGLS samples were characterised and compared with those in the uniform lattice structure.Both the uniform and RGLS samples achieve a relative density higher than 99%.The graded porosities and pore sizes in the RGLS range from 40%-80% and 330-805 µm,respectively,from the centre to the edge.The chemical etching has significantly removed the harmful partially-melted residual powder particles on the lattice struts.The compressive yield strength of RGLS is 71.5 MPa,much higher than that of the uniform sample (46.5 MPa),despite having a similar relative density of about 46%.The calculated Gibson-Ashby equation and the deformation behaviour simulation by finite element suggest that the dense outer regions with high load-bearing capability could sustain high applied stress,improving the overall strength of RGLS significantly.The cell proliferation study suggests better biological compatibility of the RGLS than the uniform structures.The findings highlight a novel strategy to improve the performance of additively manufactured artificial implants by bio-inspiration.

Mechanical property and permeability of raw coal containing methane under unloading confining pressure

Based on domestic-developed triaxial servo-controlled seepage equipment for thermal-hydrologicalmechanical coupling of coal containing methane,an experimental study was carried out to investigate mechanical property and gas permeability of raw coal,under the situation of conventional triaxial compression and unloading confining pressure tests in different gas pressure conditions.Triaxial unloading confining pressure process was reducing confining pressure while increasing axial pressure.The research results show that,compared with the peak intensity of conventional triaxial loading,the ultimate strength of coal samples of triaxial unloading confining pressure was lower,deformation under loading was far less than unloading,dilation caused by unloading was more obvious than loading.The change trend of volumetric strain would embody change of gas permeability of coal,the permeability first reduced along with volumetric strain increase,and then raised with volume strain decrease,furthermore,the change trends of permeability of coal before and after destruction were different in the stage of decreasing volume strain due to the effect of gas pressure.When gas pressure was greater,the effective confining pressure was smaller,and the radial deformation produced by unloading was greater.When the unloading failed confining pressure difference was smaller,coal would be easier to get unstable failure.

Effect of Y content and equal channel angular pressing on the microstructure, texture and mechanical property of extruded Mg-Y alloys

The microstructure, texture and mechanical property evolution of the extruded Mg-x Y(x = 1, 5 wt.%) alloys during equal channel angular pressing(ECAP) were systematically investigated using an optical microscope, electron backscatter diffraction(EBSD) and uniaxial tensile test. The Mg-Y alloys exhibited a weakened basal texture before the ECAP, and the texture was further weakened with the max basal poles dispersed along ~45° between the extrusion direction and the transverse direction after the ECAP. The Mg-5 Y alloys always exhibited a finer grain size comparing to that of Mg-1 Y for the same ECAP process. With a proper ECAP process, both the strength and elongation of Mg-5 Y alloy could be improved simultaneously after the ECAP, i.e., the yield strength(273.9 ± 1.2 MPa), ultimate strength(306.4 ± 3.0 MPa),and elongation(23.9 ± 1.0%) were increased by 10%, 6%, and 72%, respectively, comparing to that before the ECAP. This was considered to be arose from the combined effects of grain refinement, significant improved microstructure homogeneity and solid solution hardening.In addition, it was found that Mg-Y alloy with better comprehensive properties could be obtained by the decreasing-temperature ECAP processes. The yield strength-grain size relationship could be well described by the Hall-Petch relation for all the ECAPed Mg-Y alloys,which was consistent with that the texture changes did not significantly affect the average Schmid factors of basal, prismatic and pyramidal slips for both Mg-Y alloys.

Effect of microstructure evolution on mechanical property of extruded Mg-12Gd-2Er-1Zn-0.6Zr alloys

The microstructure evolution of as-cast,as-extruded and peak-aged Mg-12Gd-2Er-1Zn-0.6Zr alloys were investigated by Optical Microscope(OM),X-ray Diffraction(XRD),Scanning Electron Microscope(SEM)and Transmission Electron Microscope(TEM).The mechanical performance was also tested by tensile test at room temperature in the present study.The results indicated that the lamellar 14H-LPSO structure formed during the solid solution process at 793 K for 24 h,and also existed after hot extrusion process.The dynamic recrystallization(DRX)occurred during hot extrusion.The DRXed fine grain size was∼5μm.Meanwhile,some un-DRXed grains contained LPSO structure had a roughly orientation along the extrusion direction.The tensile test result showed that the as-extruded alloy had a better elongation of 14%due to fine DRXed grain and fiber-like un-DRXed with LPSO structure attributed to the high elongation.Because of the precipitation of theβ′-phase,the ultimate tensile strength(UTS)and yield tensile strength(YTS)increased up to 415 MPa(UTS)and 374 MPa(YTS),respectively.

Cross-sectional structure, microstructure and mechanical property evolutions of brass cladding pure copper stranded wire composite during drawing

A solid/liquid continuous casting and composite technology was used to produce d8.5 mm brass cladding pure copper stranded wire composite billet and the composite billet was then drawn. The results showed that the composite billet had good surface quality, metallurgical bonding interface between brass and pure copper as well as elongation of 53.1%. Synergistic deformation degree between pure copper wire and brass cladding layer was high during drawing. With an increase of the total deformation amount, the plastic deformation of the pure copper wire reduced triangular arc gaps between the pure copper wires and the triangular arc gaps were fully filled at 50%. When the total deformation amount was increased to 63%, dislocation cells and microbands successively formed in the pure copper wire. In the brass cladding layer, planar dislocation networks, twins and shear bands formed successively, and the main deformation mechanisms were dislocation sliding, twinning and shear deformation. The tensile strength increased from 240 MPa of the composite billet to 519 MPa of the one with the deformation amount of 63%, but the elongation decreased from 53.1% to 3.2%. A process of solid/liquid continuous casting and composite forming→drawing can work as a new compact method to produce brass cladding pure copper stranded wire composite as railway through grounding wire.

Biodegradation and Mechanical Property of Polylactic Acid/Thermoplastic Starch Blends with Poly (ethylene glycol)

The effects of adding poly （ethylene glycol） （PEG） into polylactic acid/thermoplastic starch blends （PLA/TPS） on the properties were investigated by DSC, SEM and mechanical property-testing. The blends of PLA/TPS blended with increasing content PEG exhibited lower temperature of glass transition （T） and lower temperature of melting （T） as well as higher melt flow index （MFI）, which indicates the plasticization and proeessability of the composites were dramatically improved. The tensile strength, flexural strength and izod impact strength of PLA/TPS （80/20） increased at first and then decreased with increasing content of PEG due to stronger interfacial adhesion. The optimized mechanical property can be obtained for the blend with 3 wt % PEG. The samples containing PEG after soil burial for 5 months showed quicker degradation being accompanied with large weight loss and mechanical properties loss.

Effect of annealing cooling rate on microstructure and mechanical property of 100Cr6 steel ring manufactured by cold ring rolling process

Pre-heat treatment is a vital step before cold ring rolling and it has significant effect on the microstructure and mechanical properties of rolled rings.The 100Cr6 steel rings were subjected to pre-heat treatment and subsequent cold rolling process.Scanning electron microscopy and tensile tests were applied to investigate microstructure characteristic and mechanical property variations of 100Cr6 steel rings undergoing different pre-heat treatings.The results indicate that the average diameter of carbide particles,the tensile strength and hardness increase,while the elongation decreases with the decrease of cooling rate.The cooling rate has minor effect on the yield strength of sample.After cold ring rolling,the ferrite matrix shows a clear direction along the rolling direction.The distribution of cementite is more homogeneous and the cementite particles are finer.Meanwhile,the hardness of the rolled ring is higher than that before rolling.

Effect of trace yttrium on the microstructure,mechanical property and corrosion behavior of homogenized Mg-2Zn-0.1Mn-0.3Ca-xY biological magnesium alloy

The effects of trace yttrium(Y)element on the microstructure,mechanical properties,and corrosion resistance of Mg-2Zn-0.1Mn-0.3Ca-xY(x=0,0.1,0.2,0.3)biological magnesium alloys are investigated.Results show that grain size decreases from 310 to 144µm when Y content increases from 0wt%to 0.3wt%.At the same time,volume fraction of the second phase increases from 0.4%to 6.0%,yield strength of the alloy continues to increase,and ultimate tensile strength and elongation decrease initially and then increase.When the Y content increases to 0.3wt%,Mg_(3)Zn_(6)Y phase begins to precipitate in the alloy;thus,the alloy exhibits the most excellent mechanical property.At this time,its ultimate tensile strength,yield strength,and elongation are 119 MPa,69 MPa,and 9.1%,respectively.In addition,when the Y content is 0.3wt%,the alloy shows the best corrosion resistance in the simulated body fluid(SBF).This investigation has revealed that the improvement of mechanical properties and corrosion resistance is mainly attributed to the grain refinement and the precipitated Mg_(3)Zn_(6)Y phase.

Effect of element Gd on phase constituent and mechanical property of Mg-5Sn-1Ca alloy

The Mg-5Sn-1Ca-xGd (x=0, 1) alloys were chosen to investigate the change in solidification paths, phase formation and mechanical properties. The microstructure of as-cast Mg-5Sn-1Ca alloy is composed of α-Mg, Mg2Sn and CaMgSn phases. With the addition of Gd, the formation of the Mg2Sn phase is impeded and the CaMgSn phase is refined, whereas the ultimate tensile strength and elongation decrease. The possible reasons for the variation in microstructure and mechanical properties were discussed.

Impact of W alloying on microstructure, mechanical property and corrosion resistance of face-centered cubic high entropy alloys: A review

Face-centered cubic (f.c.c.) high entropy alloys (HEAs) are attracting more and more attention owing to their excellent strength and ductility synergy, irradiation resistance, etc. However, the yield strength of f.c.c. HEAs is generally low, significantly limiting their practical applications. Recently, the alloying of W has been evidenced to be able to remarkably improve the mechanical properties of f.c.c. HEAs and is becoming a hot topic in the community of HEAs. To date, when W is introduced, multiple strengthening mechanisms, including solid-solution strengthening, precipitation strengthening (μphase,σphase, and b.c.c. phase), and grain-refinement strengthening, have been discovered to be activated or enhanced. Apart from mechanical properties, the addition of W improves corrosion resistance as W helps to form a dense WO_(3) film on the alloy surface. Until now, despite the extensive studies in the literature, there is no available review paper focusing on the W doping of the f.c.c. HEAs. In that context, the effects of W doping on f.c.c. HEAs were reviewed in this work from three aspects, i.e., microstructure,mechanical property, and corrosion resistance. We expect this work can advance the application of the W alloying strategy in the f.c.c. HEAs.