The strain jump across the Austenite-Martensite (A-M) interface in single crystal Cu-14wt%Al-4.12wt%Ni Shape Memory Alloys (SMAs) under uniaxial tension was studied in this paper. A crystallographic-based mechanics an...The strain jump across the Austenite-Martensite (A-M) interface in single crystal Cu-14wt%Al-4.12wt%Ni Shape Memory Alloys (SMAs) under uniaxial tension was studied in this paper. A crystallographic-based mechanics analysis on the formation and microstructure of the interface was performed. By using the high sensitive Moiré interference technique, the full-field deformation patterns during the transformation process were successfully recorded. The orientation of the habit plane (A-M interface) and the magnitude of the shape strain were determined precisely from the Moiré fringe patterns. The theoretical predictions on the habit plane normal and the shape strain were compared with the measured results and good agreements were obtained.展开更多
In order to effectively cope with exponent increase of the complexity faced to the rock mechanics analysis problems and the large incompatibility existing between the information level required to model the rock mass ...In order to effectively cope with exponent increase of the complexity faced to the rock mechanics analysis problems and the large incompatibility existing between the information level required to model the rock mass and engineering and our obtainable information level at hand,the integrated approaches with intelligent characters are proposed. Many previous standard methods,such as precedent type analysis,rock classification,analytic method stress-based,basic numerical methods (BEM,FEM,DEM,hybrid),and their extended numerical methods (fully coupled) to be developed,can be selected respectively or integrated accordingly. It is alternative to develop basic/fully integrated system,and internet-based approaches. These novel methods can also be selected or integrated each other or with the standard methods to perform rock mechanics analysis. Some key techniques to develop these alternative methods are discussed. It may focus in future on developing fully integrated systems and internet-based approaches. Developing an environmental,virtual facility/space shall be firstly done for this collaborative research on internet.展开更多
In order to examine the biaxial compression-compression properties of rubber fibre reinforced concrete(RFRC),an experimental study on RFRC under different lateral compressive stresses was carried out by considering di...In order to examine the biaxial compression-compression properties of rubber fibre reinforced concrete(RFRC),an experimental study on RFRC under different lateral compressive stresses was carried out by considering different rubber replacement rates and polypropylene fibre contents.The failure modes and mechanical property parameters of different RFRC working conditions were obtained from the experiment to explore the effects of rubber replacement rate and polypropylene fibre content on the biaxial compression-compression properties of RFRC.The following conclusions were drawn.Under the influence of lateral compressive stress,the biaxial compression-compression failure mode gradually developed from a columnar pattern to a flaky pattern,suggesting that the incorporation of rubber and polypropylene fibres into the concrete resulted in a significant change in the development of cracks.For different rubber replacement rates and polypropylene fibre contents,the vertical compressive stress exhibited the same developing trend under the influence of lateral compressive stress.Specifically,the lateral compressive stress imposed the minimum effect on the vertical compressive stress when the rubber replacement rate and polypropylene fibre content were 20%and 0.4%,respectively,and imposed the maximum effect when the rubber replacement rate and polypropylene fibre content were 20%and 0%,respectively.With the increase of rubber replacement rate,the vertical peak stress was significantly reduced,which implies that an appropriate amount of polypropylene fibres can increase the vertical peak stress to a certain extent.Then,the biaxial compression-compression mechanism of RFRC was analysed from the microscopic level by using scanning electron microscope(SEM).Meanwhile,based on Kupfer’s biaxial compression-compression failure criterion and the octahedral stress space,a biaxial compression-compression failure criterion for RFRC was proposed,which was proven to have good applicability.The research results of this study provide important theoretical basis for the engineering application and development of RFRC.展开更多
The efficient development and exploitation of shale oil depends on long-distance horizontal wells. As the degreeof cleaning of the wellbore plays a key role in these processes, in this study, this problem is investiga...The efficient development and exploitation of shale oil depends on long-distance horizontal wells. As the degreeof cleaning of the wellbore plays a key role in these processes, in this study, this problem is investigated experimentallyby focusing on the dimensionless cuttings bed height. A method is proposed to calculate the horizontalwellhydraulic extension taking into account the influence of the wellbore cleaning degree on the wellborepressure distribution and assess the effect of a variety of factors such as the bottom hole pressure, the circulatingpressure drop, the drilling pump performance and the formation properties. The analysis shows that the hydraulicextension of horizontal wells decreases with an increase in the cuttings bed height, and the higher the displacementof drilling fluid, the faster the hydraulic extension declines. The annular pressure drop of the horizontalsection increases with the increase of the cuttings bed height, resulting in a higher bottom-hole pressure. Severalarguments are provided to guide the safe drilling of shale oil horizontal wells and overcome the limits of currenttechnological approaches.展开更多
This paper presents an alternate graphical procedure (Method 2), to that presented in earlier publications entitled, “A Procedure for Trisecting an Acute Angle” and “A Key to Solving the Angle Trisection Problem”....This paper presents an alternate graphical procedure (Method 2), to that presented in earlier publications entitled, “A Procedure for Trisecting an Acute Angle” and “A Key to Solving the Angle Trisection Problem”. The procedure, when applied to the 30˚ and 60˚ angles that have been “proven” to be nottrisectable and the 45˚ benchmark angle that is known to be trisectable, in each case produced a construction having an identical angular relationship with Archimedes’ Construction, as in Section 2 on THEORY of this paper, where the required trisection angle was found to be one-third of its respective angle (i.e. DE’MA = 1/3 DE’CG). For example, the trisection angle for the 30˚, 45˚ and 60˚ angles were 10.00000˚, 15.00000˚, and 20.00000˚, respectively, and Section 5 on PROOF in this paper. Therefore, based on this identical angular relationship and the numerical results (i.e. to five decimal places), which represent the highest degree of accuracy and precision attainable by The Geometer’s Sketch Pad software, one can only conclude that not only the geometric requirements for arriving at an exact trisection of the 30˚ and 60˚ angle (which have been “proven” to be not-trisectable) have been met, but also, the construction is valid for any arbitrary acute angle, despite theoretical proofs to the contrary by Wantzel, Dudley, and others.展开更多
Cementitious capillary crystalline waterproof materials(CCCW for short)offer durability and excellent waterproofing properties,making them a popular option for building waterproofing.Some scholars have studied the pro...Cementitious capillary crystalline waterproof materials(CCCW for short)offer durability and excellent waterproofing properties,making them a popular option for building waterproofing.Some scholars have studied the proportioning of such materials.However,these studies lack the relationship between the impermeability pressure of mortar and the components,and the mechanism of action is somewhat debatable.Therefore,we adopted a two-step method in our experiments.Firstly,we screened out the components that significantly impact impermeability from a variety of active components by orthogonal test.We then optimized the design of the active group ratio using the simplex lattice method.Lastly,we conducted a performance test of the optimal ratio and explored the waterproofing mechanism of homemade CCCW.展开更多
A new spherical mobile robot BHQ-1 is designed. The spherical robot is driven by two internally mounted motors that induce the ball to move straight and turn around on a fiat surface. A dynamic model of the robot is d...A new spherical mobile robot BHQ-1 is designed. The spherical robot is driven by two internally mounted motors that induce the ball to move straight and turn around on a fiat surface. A dynamic model of the robot is developed with Lagrange method and factors affecting the driving torque of two motors are analyzed. The relationship between the turning radius of the robot and the length of two links is discussed in order to optimize its mechanism design. Simulation and experimental results demonstrate the good controllability and motion performance of BHQ-1.展开更多
A fully superconducting electron cyclotron resonance (ECR) ion source (SECRAL ID is currently being built in the Institute of Modern Physics, Chinese Academy of Sciences. Its key components are three superconductin...A fully superconducting electron cyclotron resonance (ECR) ion source (SECRAL ID is currently being built in the Institute of Modern Physics, Chinese Academy of Sciences. Its key components are three superconducting solenoids (Nb-Ti/Cu) and six superconducting sextupoles (Nb-Ti/Cu). Different from the conventional supercon- ducting ECR magnetic structure, the SEC17AL Ⅱ includes three superconducting solenoid coils' that are located inside the superconducting sextupoles. The SECRAL Ⅱ can significantly reduce the interaction forces between the sextupole and the solenoids, and the magnets can also be more compact in size. For this multi-component SECRAL Ⅱ generating its self field of -8 T and being often exposed to the high self field, the mechanical analysis has become the main issue to keep their stress at 〈200 MPa on coils. The analytical and experimental results in mechanics are presented in the SECRAL Ⅱ structure. To improve the accuracy and efficiency of analysis, according to the composite rule of micromechanics, the equivalent uniform windings are used to simulate the epoxy-impregnated Nb-Ti/Cu coils. In addition, using low temperature strain gauges and a wireless fast strain acquisition system, a fundamental experiment on the based on our analysis, the stresses and deformations optimized. strains developments of a sextupole is reported. Finally, for its assembly of each SECRAL Ⅱ coil will be further展开更多
International thermonuclear experimental reactor (ITER) edge localized mode (ELM) coils are used to mitigate or suppress ELMs. The location of the coils in the vacuum vessel and behind the blankets exposes them to...International thermonuclear experimental reactor (ITER) edge localized mode (ELM) coils are used to mitigate or suppress ELMs. The location of the coils in the vacuum vessel and behind the blankets exposes them to high radiation levels and high temperatures. The feeders provide the power and cooling water for ELM coils. They are located in the chinmey ports and experience lower radiation and temperature levels. These coils and feeders work in a high magnetic field environment and are subjected to alternating electromagnetic force due to the interaction between high magnetic field and alternating current (AC) current in the coils. They are also subjected to thermal stresses due to thermal expansion. Using the ITER upper ELM coil and feeder as an example, mechanical analyses are performed to verify and optimize the updated design to enhance their structural performance. The results show that the conductor, jacket and bracket can meet the static, fatigue and crack threshold criteria. The optimization indicates that adding chamfers to the bracket can reduce the high stress of the bracket, and removing two rails can reduce the peak reaction force on the two rails arising from thermal expansion.展开更多
Low-basis-weight paper lacks normal strength and stiffness. Waterborne epoxy resin could be employed with oxidized starch to improve paper stiffness through surface sizing. In this study,the mechanism of enhancing sti...Low-basis-weight paper lacks normal strength and stiffness. Waterborne epoxy resin could be employed with oxidized starch to improve paper stiffness through surface sizing. In this study,the mechanism of enhancing stiffness by adding waterborne epoxy resin was fully investigated. The results indicated that through surface sizing with epoxy resin,the paper thickness was preserved,whereas the elastic modulus increased significantly and the epoxy resin had positive impact on single fiber strength. A rigid resin layer and interpenetrating polymer network formed on the surface and in the inner layer of the paper,respectively. The formed resin layer and interpenetrating polymer network strongly supported the paper,leading to the improvement of the elastic modulus and stiffness. The stiffness improvement through surface sizing was mainly due to the formation of a fibrous composite layer and penetration of the sizing agent into the inner layers of the paper. The better the combination between fiber and sizing agent,the higher were the elastic modulus and the stiffness of the whole paper.展开更多
Acrylonitrile-butadiene-Styrene (ABS), with and without calcium carbonate (calcite) particles,was used as the matrix for reinforcement with as-received short-glass fibres (were originallytreated by the manufacturer) a...Acrylonitrile-butadiene-Styrene (ABS), with and without calcium carbonate (calcite) particles,was used as the matrix for reinforcement with as-received short-glass fibres (were originallytreated by the manufacturer) and sized short-glass fibres with two amino-silane coupling agents.The calcite particle content is 0, 11.7 and 23.5 vol. pct for the matrices. The glass fiber contentis 0, 10 and 15 vol. pct. The matrix materials and corresponding composites were compoundedusing a twin screw extruder and dumbbell-shaped tensile bars were prepared with an injectionmolding process. The tensile and flexural properties as well as the unnotched and notchedCharpy impact energies of short glass fibre/calcite/ABS composites were studied in this paper.The effects of fibres, fibre surface treatments and particles on these mechanical properties ofthe composites were discussed in detail. An importarit information was obtained, which is thatthe tensile and flexural strengths of hybrid SGF/calcite/ABS composites are the same as thoseof corresponding fibre composites when the ratio of the interfacial adhesion strength betweenparticles and matrix to that between fibres and matrix is higher than certain value. otherwise theformer are lower than the latter.展开更多
Although the parallel mechanisms have the advantages of high accuracy, velocity, stiffness, and payload capacity, the shortcomings of the space utilization and workspace limit the applications in the confined space. A...Although the parallel mechanisms have the advantages of high accuracy, velocity, stiffness, and payload capacity, the shortcomings of the space utilization and workspace limit the applications in the confined space. A novel 3 degrees of freedom spatial parallel manipulator 3-PSR-O(prismatic-spherical-revolute) is proposed, which possesses a compact architecture and extended workspace while maintaining the inherent advantages of the parallel mechanisms. The direct-inverse position, singularity and workspace are investigated. The mapping method is adopted in the position analysis, and the closed form solution is derived in the form of a six order equation. The singularity analysis of the mechanism is also carried out based on the geometrical constraints, including six singularity boundaries. A feature boundary, which is independent of the prismatic joints' stroke limit, is obtained by integrating the six singularity boundaries. According to the formation of the reachable workspace, a concept of basic workspace is also introduced and presented in the analytical way. By demarcating the basic workspace along the central height with the feature boundary, the reachable workspace can be derived and analyzed more efficiently. Finally, a comparative study on the space utilization between the 3-PSP parallel mechanism and the new mechanism is also presented. The area of feature boundary of the new mechanism is about 140% of the 3-PSP parallel mechanism, while its installation radius is only 1/2 of the 3-PSP parallel mechanism. The proposed parallel mechanism shows great space utilization, and is ideally suited for applications in confined space occasions such as immersion lithography, nano-imprint etc.展开更多
Conventional flexible joints generally have limited range of motion and high stress concentration. To overcome these shortcomings, corrugated flexure beam(CF beam) is designed because of its large flexibility obtain...Conventional flexible joints generally have limited range of motion and high stress concentration. To overcome these shortcomings, corrugated flexure beam(CF beam) is designed because of its large flexibility obtained from longer overall length on the same span. The successful design of compliant mechanisms using CF beam requires manipulation of the stiffnesses as the design variables. Empirical equations of the CF beam stiffness components, except of the torsional stiffness, are obtained by curve-fitting method. The application ranges of all the parameters in each empirical equation are also discussed. The ratio of off-axis to axial stiffness is considered as a key characteristic of an effective compliant joint. And parameter study shows that the radius of semi-circular segment and the length of straight segment contribute most to the ratio. At last, CF beam is used to design translational and rotational flexible joints, which also verifies the validity of the empirical equations. CF beam with large flexibility is presented, and empirical equations of its stiffness are proposed to facilitate the design of flexible joint with large range of motion.展开更多
With the uncertainties related to operating conditions,in-service non-destructive testing(NDT) measurements and material properties considered in the structural integrity assessment,probabilistic analysis based on t...With the uncertainties related to operating conditions,in-service non-destructive testing(NDT) measurements and material properties considered in the structural integrity assessment,probabilistic analysis based on the failure assessment diagram(FAD) approach has recently become an important concern.However,the point density revealing the probabilistic distribution characteristics of the assessment points is usually ignored.To obtain more detailed and direct knowledge from the reliability analysis,an improved probabilistic fracture mechanics(PFM) assessment method is proposed.By integrating 2D kernel density estimation(KDE) technology into the traditional probabilistic assessment,the probabilistic density of the randomly distributed assessment points is visualized in the assessment diagram.Moreover,a modified interval sensitivity analysis is implemented and compared with probabilistic sensitivity analysis.The improved reliability analysis method is applied to the assessment of a high pressure pipe containing an axial internal semi-elliptical surface crack.The results indicate that these two methods can give consistent sensitivities of input parameters,but the interval sensitivity analysis is computationally more efficient.Meanwhile,the point density distribution and its contour are plotted in the FAD,thereby better revealing the characteristics of PFM assessment.This study provides a powerful tool for the reliability analysis of critical structures.展开更多
Forward kinematics analysis of a novel 5-DOF parallel mechanism using tetrahedron configurations is presented. Such mechanism is suitable to many tasks requiring less than 6 DOFs. It consists of a movable platform con...Forward kinematics analysis of a novel 5-DOF parallel mechanism using tetrahedron configurations is presented. Such mechanism is suitable to many tasks requiring less than 6 DOFs. It consists of a movable platform connected to the base by five identical 6-DOF active limbs plus one active limb with its DOF being exactly the same as the specified DOF of the movable platform, which leads to its legs' topology 4-UPS/UPU. Based on the tetmhedron geometry, both closed-form solution with an extra sensor and numerical method using iterative algorithm are employed to obtain the forward kinematics solutions of the mechanism. Compared with the conventional methods, the proposed closed-form solution has the advantages in automatically avoiding unnecessary complex roots and getting a unique solution for the forward kinematics. Finally, an example shows that the proposed numerical algorithm is so effective that it enables a real-time forward kinematics solution to be achieved and the initial value can be chosen easily.展开更多
Based on a modified pseudo-rigid-body model,the frequency characteristics and sensitivity of the large-deformation compliant mechanism are studied.Firstly,the pseudo-rigid-body model under the static and kinetic condi...Based on a modified pseudo-rigid-body model,the frequency characteristics and sensitivity of the large-deformation compliant mechanism are studied.Firstly,the pseudo-rigid-body model under the static and kinetic conditions is modified to enable the modified pseudo-rigid-body model to be more suitable for the dynamic analysis of the compliant mechanism.Subsequently,based on the modified pseudo-rigid-body model,the dynamic equations of the ordinary compliant four-bar mechanism are established using the analytical mechanics.Finally,in combination with the finite element analysis software ANSYS,the frequency characteristics and sensitivity of the compliant mechanism are analyzed by taking the compliant parallel-guiding mechanism and the compliant bistable mechanism as examples.From the simulation results,the dynamic characteristics of compliant mechanism are relatively sensitive to the structure size,section parameter,and characteristic parameter of material on mechanisms.The results could provide great theoretical significance and application values for the structural optimization of compliant mechanisms,the improvement of their dynamic properties and the expansion of their application range.展开更多
Considering the feature of distributions of parameters within the micro-hollow cathode discharge, we use a simple method to separate the sheath region characterized by drastic changes of plasma parameters and the bulk...Considering the feature of distributions of parameters within the micro-hollow cathode discharge, we use a simple method to separate the sheath region characterized by drastic changes of plasma parameters and the bulk plasma region characterized by smooth changes of plasma parameters. A zero-dimensional chemical kinetic model is used to analyze the dissociation mechanism of CO2 in the bulk plasma region of a micro-hollow cathode discharge and is validated by comparisons with previous modeling and experimental results. The analysis of the chemical kinetic processes has shown that the electron impact dissociation and heavy species impact dissociation are dominant in different stages of the rnicro-hollow cathode discharge process for a given applied voltage. The analysis of energy consumption distributions under different applied voltages reveals that the main reason of the conversion improvement with the increase of the applied voltage is that more input energy is distributed to the heavy species impact dissociation.展开更多
We first design and analyze the contour surface of the globoidal indexing cam with the aid of computer, and then do optimum design according to the requirements of dynamics. Finally, we discuss the problem of the pres...We first design and analyze the contour surface of the globoidal indexing cam with the aid of computer, and then do optimum design according to the requirements of dynamics. Finally, we discuss the problem of the pressure angle of the globoidal indexing cam mechanism in detail and put forward a new concept of equivalent pressure angle.展开更多
Mechanical assembly has its own dynamic quality directly affecting the dynamic quality of whole product and should be considered in quality inspection and estimation of mechanical assembly. Based on functional relatio...Mechanical assembly has its own dynamic quality directly affecting the dynamic quality of whole product and should be considered in quality inspection and estimation of mechanical assembly. Based on functional relations between dynamic characteristics involved in mechanical assembly, the effects of assembling process on dynamic characteristics of substructural components of an assembly system are investigated by substructuring analysis. Assembly-coupling dynamic stiffness is clarified as the dominant factor of the effects and can be used as a quantitative measure of assembly dynamic quality. Two computational schemes using frequency response functions(FRFs) to determine the stiffness are provided and discussed by inverse substructuring analysis, including their applicable conditions and implementation procedure in application. Eigenvalue analysis on matrix-ratios of FRFs before and after assembling is employed and well validates the analytical outcomes and the schemes via both a lumped-parameter model and its analogic experimental counterpart. Applying the two schemes to inspect the dynamic quality provides the message of dynamic performance of the assembly system, and therefore improves conventional quality inspection and estimation of mechanical assembly in completeness.展开更多
The transport of fluid, nutrients, and signaling molecules in the bone lacunar-canalicular system (LCS) is critical for osteocyte survival and function. We have applied the fluorescence recovery after photobleaching...The transport of fluid, nutrients, and signaling molecules in the bone lacunar-canalicular system (LCS) is critical for osteocyte survival and function. We have applied the fluorescence recovery after photobleaching (FRAP) approach to quantify load-induced fluid and solute transport in the LCS in situ, but the measurements were limited to cortical regions 30-50 μm underneath the periosteum due to the constrains of laser penetration. With this work, we aimed to expand our understanding of load-induced fluid and solute transport in both trabecular and cortical bone using a multiscaled image-based finite element analysis (FEA) approach. An intact murine tibia was first re-constructed from microCT images into a three-dimensional (3D) linear elastic FEA model, and the matrix deformations at various locations were calculated under axial loading. A segment of the above 3D model was then imported to the biphasic poroelasticity analysis platform (FEBio) to predict load-induced fluid pressure fields, and interstitial solute/fluid flows through LCS in both cortical and trabecular regions. Further, secondary flow effects such as the shear stress and/or drag force acting on osteocytes, the presumed mechano-sensors in bone, were derived using the previously developed ultrastructural model of Brinkman flow in the canaliculi. The material properties assumed in the FEA models were validated against previously obtained strain and FRAP transport data measured on the cortical cortex. Our results demonstrated the feasibility of this computational approach in estimating the fluid flux in the LCS and the cellular stimulation forces (shear and drag forces) for osteocytes in any cortical and trabecular bone locations, allowing further studies of how the activation of osteocytes correlates with in vivo functional bone formation. The study provides a promising platform to reveal potential cellular mechanisms underlying the anabolic power of exercises and physical activities in treating patients with skeletal deficiencies.展开更多
基金The project supported by the National Natural Science Foundation of China (19891180(3))Hong Kong Research Grant Committee (DAG 96/97. EG15)
文摘The strain jump across the Austenite-Martensite (A-M) interface in single crystal Cu-14wt%Al-4.12wt%Ni Shape Memory Alloys (SMAs) under uniaxial tension was studied in this paper. A crystallographic-based mechanics analysis on the formation and microstructure of the interface was performed. By using the high sensitive Moiré interference technique, the full-field deformation patterns during the transformation process were successfully recorded. The orientation of the habit plane (A-M interface) and the magnitude of the shape strain were determined precisely from the Moiré fringe patterns. The theoretical predictions on the habit plane normal and the shape strain were compared with the measured results and good agreements were obtained.
基金Nature Science Foundation of China under Grant no.50179034.
文摘In order to effectively cope with exponent increase of the complexity faced to the rock mechanics analysis problems and the large incompatibility existing between the information level required to model the rock mass and engineering and our obtainable information level at hand,the integrated approaches with intelligent characters are proposed. Many previous standard methods,such as precedent type analysis,rock classification,analytic method stress-based,basic numerical methods (BEM,FEM,DEM,hybrid),and their extended numerical methods (fully coupled) to be developed,can be selected respectively or integrated accordingly. It is alternative to develop basic/fully integrated system,and internet-based approaches. These novel methods can also be selected or integrated each other or with the standard methods to perform rock mechanics analysis. Some key techniques to develop these alternative methods are discussed. It may focus in future on developing fully integrated systems and internet-based approaches. Developing an environmental,virtual facility/space shall be firstly done for this collaborative research on internet.
基金supported by the National 12th Five Year Plan of Science and Technology Support Project(2015 BAL02b02)National Spark Plan Project(2015 GA690045),Jiangsu Province“Six Talent Peaks”Team Project(XCL-CXTD−007).
文摘In order to examine the biaxial compression-compression properties of rubber fibre reinforced concrete(RFRC),an experimental study on RFRC under different lateral compressive stresses was carried out by considering different rubber replacement rates and polypropylene fibre contents.The failure modes and mechanical property parameters of different RFRC working conditions were obtained from the experiment to explore the effects of rubber replacement rate and polypropylene fibre content on the biaxial compression-compression properties of RFRC.The following conclusions were drawn.Under the influence of lateral compressive stress,the biaxial compression-compression failure mode gradually developed from a columnar pattern to a flaky pattern,suggesting that the incorporation of rubber and polypropylene fibres into the concrete resulted in a significant change in the development of cracks.For different rubber replacement rates and polypropylene fibre contents,the vertical compressive stress exhibited the same developing trend under the influence of lateral compressive stress.Specifically,the lateral compressive stress imposed the minimum effect on the vertical compressive stress when the rubber replacement rate and polypropylene fibre content were 20%and 0.4%,respectively,and imposed the maximum effect when the rubber replacement rate and polypropylene fibre content were 20%and 0%,respectively.With the increase of rubber replacement rate,the vertical peak stress was significantly reduced,which implies that an appropriate amount of polypropylene fibres can increase the vertical peak stress to a certain extent.Then,the biaxial compression-compression mechanism of RFRC was analysed from the microscopic level by using scanning electron microscope(SEM).Meanwhile,based on Kupfer’s biaxial compression-compression failure criterion and the octahedral stress space,a biaxial compression-compression failure criterion for RFRC was proposed,which was proven to have good applicability.The research results of this study provide important theoretical basis for the engineering application and development of RFRC.
基金supported by CNPC Key Core Technology Research Projects (2022ZG06)project funded by China Postdoctoral Science Foundation (2021M693508)Basic research and strategic reserve technology research fund project of institutes directly under CNPC.
文摘The efficient development and exploitation of shale oil depends on long-distance horizontal wells. As the degreeof cleaning of the wellbore plays a key role in these processes, in this study, this problem is investigated experimentallyby focusing on the dimensionless cuttings bed height. A method is proposed to calculate the horizontalwellhydraulic extension taking into account the influence of the wellbore cleaning degree on the wellborepressure distribution and assess the effect of a variety of factors such as the bottom hole pressure, the circulatingpressure drop, the drilling pump performance and the formation properties. The analysis shows that the hydraulicextension of horizontal wells decreases with an increase in the cuttings bed height, and the higher the displacementof drilling fluid, the faster the hydraulic extension declines. The annular pressure drop of the horizontalsection increases with the increase of the cuttings bed height, resulting in a higher bottom-hole pressure. Severalarguments are provided to guide the safe drilling of shale oil horizontal wells and overcome the limits of currenttechnological approaches.
文摘This paper presents an alternate graphical procedure (Method 2), to that presented in earlier publications entitled, “A Procedure for Trisecting an Acute Angle” and “A Key to Solving the Angle Trisection Problem”. The procedure, when applied to the 30˚ and 60˚ angles that have been “proven” to be nottrisectable and the 45˚ benchmark angle that is known to be trisectable, in each case produced a construction having an identical angular relationship with Archimedes’ Construction, as in Section 2 on THEORY of this paper, where the required trisection angle was found to be one-third of its respective angle (i.e. DE’MA = 1/3 DE’CG). For example, the trisection angle for the 30˚, 45˚ and 60˚ angles were 10.00000˚, 15.00000˚, and 20.00000˚, respectively, and Section 5 on PROOF in this paper. Therefore, based on this identical angular relationship and the numerical results (i.e. to five decimal places), which represent the highest degree of accuracy and precision attainable by The Geometer’s Sketch Pad software, one can only conclude that not only the geometric requirements for arriving at an exact trisection of the 30˚ and 60˚ angle (which have been “proven” to be not-trisectable) have been met, but also, the construction is valid for any arbitrary acute angle, despite theoretical proofs to the contrary by Wantzel, Dudley, and others.
文摘Cementitious capillary crystalline waterproof materials(CCCW for short)offer durability and excellent waterproofing properties,making them a popular option for building waterproofing.Some scholars have studied the proportioning of such materials.However,these studies lack the relationship between the impermeability pressure of mortar and the components,and the mechanism of action is somewhat debatable.Therefore,we adopted a two-step method in our experiments.Firstly,we screened out the components that significantly impact impermeability from a variety of active components by orthogonal test.We then optimized the design of the active group ratio using the simplex lattice method.Lastly,we conducted a performance test of the optimal ratio and explored the waterproofing mechanism of homemade CCCW.
基金This project is supported by National Hi-tech Research and Development Program of China(863 Program, No.2003AA404190).
文摘A new spherical mobile robot BHQ-1 is designed. The spherical robot is driven by two internally mounted motors that induce the ball to move straight and turn around on a fiat surface. A dynamic model of the robot is developed with Lagrange method and factors affecting the driving torque of two motors are analyzed. The relationship between the turning radius of the robot and the length of two links is discussed in order to optimize its mechanism design. Simulation and experimental results demonstrate the good controllability and motion performance of BHQ-1.
基金Supported by the National Natural Science Foundation of China under Grant No 11302225the China Postdoctoral Science Foundation under Grant Nos 2014M560820 and 2015T81071
文摘A fully superconducting electron cyclotron resonance (ECR) ion source (SECRAL ID is currently being built in the Institute of Modern Physics, Chinese Academy of Sciences. Its key components are three superconducting solenoids (Nb-Ti/Cu) and six superconducting sextupoles (Nb-Ti/Cu). Different from the conventional supercon- ducting ECR magnetic structure, the SEC17AL Ⅱ includes three superconducting solenoid coils' that are located inside the superconducting sextupoles. The SECRAL Ⅱ can significantly reduce the interaction forces between the sextupole and the solenoids, and the magnets can also be more compact in size. For this multi-component SECRAL Ⅱ generating its self field of -8 T and being often exposed to the high self field, the mechanical analysis has become the main issue to keep their stress at 〈200 MPa on coils. The analytical and experimental results in mechanics are presented in the SECRAL Ⅱ structure. To improve the accuracy and efficiency of analysis, according to the composite rule of micromechanics, the equivalent uniform windings are used to simulate the epoxy-impregnated Nb-Ti/Cu coils. In addition, using low temperature strain gauges and a wireless fast strain acquisition system, a fundamental experiment on the based on our analysis, the stresses and deformations optimized. strains developments of a sextupole is reported. Finally, for its assembly of each SECRAL Ⅱ coil will be further
文摘International thermonuclear experimental reactor (ITER) edge localized mode (ELM) coils are used to mitigate or suppress ELMs. The location of the coils in the vacuum vessel and behind the blankets exposes them to high radiation levels and high temperatures. The feeders provide the power and cooling water for ELM coils. They are located in the chinmey ports and experience lower radiation and temperature levels. These coils and feeders work in a high magnetic field environment and are subjected to alternating electromagnetic force due to the interaction between high magnetic field and alternating current (AC) current in the coils. They are also subjected to thermal stresses due to thermal expansion. Using the ITER upper ELM coil and feeder as an example, mechanical analyses are performed to verify and optimize the updated design to enhance their structural performance. The results show that the conductor, jacket and bracket can meet the static, fatigue and crack threshold criteria. The optimization indicates that adding chamfers to the bracket can reduce the high stress of the bracket, and removing two rails can reduce the peak reaction force on the two rails arising from thermal expansion.
基金financially supported by the National Natural Science Funds of China(grant number31470599)the Priority Academic Program Development of Jiangsu Higher Education Institutions,China
文摘Low-basis-weight paper lacks normal strength and stiffness. Waterborne epoxy resin could be employed with oxidized starch to improve paper stiffness through surface sizing. In this study,the mechanism of enhancing stiffness by adding waterborne epoxy resin was fully investigated. The results indicated that through surface sizing with epoxy resin,the paper thickness was preserved,whereas the elastic modulus increased significantly and the epoxy resin had positive impact on single fiber strength. A rigid resin layer and interpenetrating polymer network formed on the surface and in the inner layer of the paper,respectively. The formed resin layer and interpenetrating polymer network strongly supported the paper,leading to the improvement of the elastic modulus and stiffness. The stiffness improvement through surface sizing was mainly due to the formation of a fibrous composite layer and penetration of the sizing agent into the inner layers of the paper. The better the combination between fiber and sizing agent,the higher were the elastic modulus and the stiffness of the whole paper.
文摘Acrylonitrile-butadiene-Styrene (ABS), with and without calcium carbonate (calcite) particles,was used as the matrix for reinforcement with as-received short-glass fibres (were originallytreated by the manufacturer) and sized short-glass fibres with two amino-silane coupling agents.The calcite particle content is 0, 11.7 and 23.5 vol. pct for the matrices. The glass fiber contentis 0, 10 and 15 vol. pct. The matrix materials and corresponding composites were compoundedusing a twin screw extruder and dumbbell-shaped tensile bars were prepared with an injectionmolding process. The tensile and flexural properties as well as the unnotched and notchedCharpy impact energies of short glass fibre/calcite/ABS composites were studied in this paper.The effects of fibres, fibre surface treatments and particles on these mechanical properties ofthe composites were discussed in detail. An importarit information was obtained, which is thatthe tensile and flexural strengths of hybrid SGF/calcite/ABS composites are the same as thoseof corresponding fibre composites when the ratio of the interfacial adhesion strength betweenparticles and matrix to that between fibres and matrix is higher than certain value. otherwise theformer are lower than the latter.
基金Supported by National Natural Science Foundation of China(Grant No.51221004)National Hi-tech Research and Development Program of China(863 Program,Grant No.2012AA040605)
文摘Although the parallel mechanisms have the advantages of high accuracy, velocity, stiffness, and payload capacity, the shortcomings of the space utilization and workspace limit the applications in the confined space. A novel 3 degrees of freedom spatial parallel manipulator 3-PSR-O(prismatic-spherical-revolute) is proposed, which possesses a compact architecture and extended workspace while maintaining the inherent advantages of the parallel mechanisms. The direct-inverse position, singularity and workspace are investigated. The mapping method is adopted in the position analysis, and the closed form solution is derived in the form of a six order equation. The singularity analysis of the mechanism is also carried out based on the geometrical constraints, including six singularity boundaries. A feature boundary, which is independent of the prismatic joints' stroke limit, is obtained by integrating the six singularity boundaries. According to the formation of the reachable workspace, a concept of basic workspace is also introduced and presented in the analytical way. By demarcating the basic workspace along the central height with the feature boundary, the reachable workspace can be derived and analyzed more efficiently. Finally, a comparative study on the space utilization between the 3-PSP parallel mechanism and the new mechanism is also presented. The area of feature boundary of the new mechanism is about 140% of the 3-PSP parallel mechanism, while its installation radius is only 1/2 of the 3-PSP parallel mechanism. The proposed parallel mechanism shows great space utilization, and is ideally suited for applications in confined space occasions such as immersion lithography, nano-imprint etc.
基金Supported by National Natural Science Foundation of China(Grant Nos.51205134,91223201)Doctoral Fund of Ministry of Education of China(Grant No.20120172120001)Research Project of State Key Laboratory of Mechanical System and Vibration,China(Grant No.MSV201405)
文摘Conventional flexible joints generally have limited range of motion and high stress concentration. To overcome these shortcomings, corrugated flexure beam(CF beam) is designed because of its large flexibility obtained from longer overall length on the same span. The successful design of compliant mechanisms using CF beam requires manipulation of the stiffnesses as the design variables. Empirical equations of the CF beam stiffness components, except of the torsional stiffness, are obtained by curve-fitting method. The application ranges of all the parameters in each empirical equation are also discussed. The ratio of off-axis to axial stiffness is considered as a key characteristic of an effective compliant joint. And parameter study shows that the radius of semi-circular segment and the length of straight segment contribute most to the ratio. At last, CF beam is used to design translational and rotational flexible joints, which also verifies the validity of the empirical equations. CF beam with large flexibility is presented, and empirical equations of its stiffness are proposed to facilitate the design of flexible joint with large range of motion.
基金supported by National Department Public Benefit Research Foundation of China (Grant No. 200810411)
文摘With the uncertainties related to operating conditions,in-service non-destructive testing(NDT) measurements and material properties considered in the structural integrity assessment,probabilistic analysis based on the failure assessment diagram(FAD) approach has recently become an important concern.However,the point density revealing the probabilistic distribution characteristics of the assessment points is usually ignored.To obtain more detailed and direct knowledge from the reliability analysis,an improved probabilistic fracture mechanics(PFM) assessment method is proposed.By integrating 2D kernel density estimation(KDE) technology into the traditional probabilistic assessment,the probabilistic density of the randomly distributed assessment points is visualized in the assessment diagram.Moreover,a modified interval sensitivity analysis is implemented and compared with probabilistic sensitivity analysis.The improved reliability analysis method is applied to the assessment of a high pressure pipe containing an axial internal semi-elliptical surface crack.The results indicate that these two methods can give consistent sensitivities of input parameters,but the interval sensitivity analysis is computationally more efficient.Meanwhile,the point density distribution and its contour are plotted in the FAD,thereby better revealing the characteristics of PFM assessment.This study provides a powerful tool for the reliability analysis of critical structures.
文摘Forward kinematics analysis of a novel 5-DOF parallel mechanism using tetrahedron configurations is presented. Such mechanism is suitable to many tasks requiring less than 6 DOFs. It consists of a movable platform connected to the base by five identical 6-DOF active limbs plus one active limb with its DOF being exactly the same as the specified DOF of the movable platform, which leads to its legs' topology 4-UPS/UPU. Based on the tetmhedron geometry, both closed-form solution with an extra sensor and numerical method using iterative algorithm are employed to obtain the forward kinematics solutions of the mechanism. Compared with the conventional methods, the proposed closed-form solution has the advantages in automatically avoiding unnecessary complex roots and getting a unique solution for the forward kinematics. Finally, an example shows that the proposed numerical algorithm is so effective that it enables a real-time forward kinematics solution to be achieved and the initial value can be chosen easily.
基金Supported by Fundamental Research Funds for the Central Universities of China(Grant Nos.2014QNB18,2015XKMS022)National Natural Science Foundation of China(Grant No.51475456)+1 种基金Priority Academic Programme Development of Jiangsu Higher Education Institutionsthe Visiting Scholar Foundation of China Scholarship Council
文摘Based on a modified pseudo-rigid-body model,the frequency characteristics and sensitivity of the large-deformation compliant mechanism are studied.Firstly,the pseudo-rigid-body model under the static and kinetic conditions is modified to enable the modified pseudo-rigid-body model to be more suitable for the dynamic analysis of the compliant mechanism.Subsequently,based on the modified pseudo-rigid-body model,the dynamic equations of the ordinary compliant four-bar mechanism are established using the analytical mechanics.Finally,in combination with the finite element analysis software ANSYS,the frequency characteristics and sensitivity of the compliant mechanism are analyzed by taking the compliant parallel-guiding mechanism and the compliant bistable mechanism as examples.From the simulation results,the dynamic characteristics of compliant mechanism are relatively sensitive to the structure size,section parameter,and characteristic parameter of material on mechanisms.The results could provide great theoretical significance and application values for the structural optimization of compliant mechanisms,the improvement of their dynamic properties and the expansion of their application range.
基金Supported by the National Natural Science Foundation of China under Grant Nos 11575019 and 11275021
文摘Considering the feature of distributions of parameters within the micro-hollow cathode discharge, we use a simple method to separate the sheath region characterized by drastic changes of plasma parameters and the bulk plasma region characterized by smooth changes of plasma parameters. A zero-dimensional chemical kinetic model is used to analyze the dissociation mechanism of CO2 in the bulk plasma region of a micro-hollow cathode discharge and is validated by comparisons with previous modeling and experimental results. The analysis of the chemical kinetic processes has shown that the electron impact dissociation and heavy species impact dissociation are dominant in different stages of the rnicro-hollow cathode discharge process for a given applied voltage. The analysis of energy consumption distributions under different applied voltages reveals that the main reason of the conversion improvement with the increase of the applied voltage is that more input energy is distributed to the heavy species impact dissociation.
文摘We first design and analyze the contour surface of the globoidal indexing cam with the aid of computer, and then do optimum design according to the requirements of dynamics. Finally, we discuss the problem of the pressure angle of the globoidal indexing cam mechanism in detail and put forward a new concept of equivalent pressure angle.
基金Supported by National Natural Science Foundation of China(Grant No.51475211)
文摘Mechanical assembly has its own dynamic quality directly affecting the dynamic quality of whole product and should be considered in quality inspection and estimation of mechanical assembly. Based on functional relations between dynamic characteristics involved in mechanical assembly, the effects of assembling process on dynamic characteristics of substructural components of an assembly system are investigated by substructuring analysis. Assembly-coupling dynamic stiffness is clarified as the dominant factor of the effects and can be used as a quantitative measure of assembly dynamic quality. Two computational schemes using frequency response functions(FRFs) to determine the stiffness are provided and discussed by inverse substructuring analysis, including their applicable conditions and implementation procedure in application. Eigenvalue analysis on matrix-ratios of FRFs before and after assembling is employed and well validates the analytical outcomes and the schemes via both a lumped-parameter model and its analogic experimental counterpart. Applying the two schemes to inspect the dynamic quality provides the message of dynamic performance of the assembly system, and therefore improves conventional quality inspection and estimation of mechanical assembly in completeness.
基金supported by grants from NIH (P30GM103333 and RO1AR054385 to LW)China CSC fellowship (to LF)DOD W81XWH-13-1-0148 (to XLL)
文摘The transport of fluid, nutrients, and signaling molecules in the bone lacunar-canalicular system (LCS) is critical for osteocyte survival and function. We have applied the fluorescence recovery after photobleaching (FRAP) approach to quantify load-induced fluid and solute transport in the LCS in situ, but the measurements were limited to cortical regions 30-50 μm underneath the periosteum due to the constrains of laser penetration. With this work, we aimed to expand our understanding of load-induced fluid and solute transport in both trabecular and cortical bone using a multiscaled image-based finite element analysis (FEA) approach. An intact murine tibia was first re-constructed from microCT images into a three-dimensional (3D) linear elastic FEA model, and the matrix deformations at various locations were calculated under axial loading. A segment of the above 3D model was then imported to the biphasic poroelasticity analysis platform (FEBio) to predict load-induced fluid pressure fields, and interstitial solute/fluid flows through LCS in both cortical and trabecular regions. Further, secondary flow effects such as the shear stress and/or drag force acting on osteocytes, the presumed mechano-sensors in bone, were derived using the previously developed ultrastructural model of Brinkman flow in the canaliculi. The material properties assumed in the FEA models were validated against previously obtained strain and FRAP transport data measured on the cortical cortex. Our results demonstrated the feasibility of this computational approach in estimating the fluid flux in the LCS and the cellular stimulation forces (shear and drag forces) for osteocytes in any cortical and trabecular bone locations, allowing further studies of how the activation of osteocytes correlates with in vivo functional bone formation. The study provides a promising platform to reveal potential cellular mechanisms underlying the anabolic power of exercises and physical activities in treating patients with skeletal deficiencies.