Microstructural Transformation and Precipitation of an Ultra-high Strength Steel under Continuous Cooling

We investigated phase transition and precipitation of ultra-high strength steel（UHSS）in a new ＂short process＂ with controlled rolling and controlled cooling.Thermalexpansion test combined with metallographic observation was used to research the continuous cooling transformation（CCT）curve.Moreover,the microstructuraltransformation and precipitation law was revealed by morphologicalobservation and alloying elements by electron probe micro-analyzer（EPMA）.Transmission electron microscopy（TEM）was utilized to analyze the composition and grain orientation of microstructure.The study showed that the measured criticaltransformation temperatures of Ac1 and Ac3 were 746 and 868 ℃,respectively.The CCT curve indicated that the undercooled austenite was transformed into proeutectoid ferrite and bainite with HV 520 in a broad range of cooling rate 0.1^（-1） ℃·s^（-1）.When subjected to a cooling rate of 1 ℃·s^（-1）,the undercooled austenite was divided into small-sized blocks by formed martensite.With further increase of cooling rate,micro-hardness increased dramatically,the microstructure of specimen was mainly lathe bainite（LB）,granular bainite（GB）,lath martensite（LM）and residualaustenite.By diffraction test analysis,it was identified that there was K-S orientation relationship between martensite and austenite for {110}_α//{111}_γ,{111}_α//{101}_γ.EPMA clearly showed that carbon diffused adequately due to staying for a long time at high temperature with a lower cooling rate of 2 ℃·s-1.Phase transition drive force was lower and the residualaustenite existed in the block form of Martensite austenite island（M-A）.With the increase of cooling rate to 10 ℃·s^（-1）,the block residualaustenite reduced,the carbon content of residualaustenite increased and α phase around the residualaustenite formed into a low carbon bainite form.

Study on the Reversible DC-DC Converter as Interface between Low and Medium Voltage DC Networks

This paper introduces an isolated reversible DC-DC converter with a particular topology, which benefits from both the NPC （neutral point clamped） structure and the series-parallel connection of converters. The key property of the proposed topology is the output voltage elevation above the blocking capabilities of each switch, without taking to a delicate synchronization of series-connected semiconductors. The converter is composed by two identical cells, each containing a full bridge, a medium frequency transformer and an NPC converter, connected in parallel at the input and in series at the output. The operation principle of each cell, into which a trapezoidal modulation was implemented, is similar to a DAB （dual active bridge）. A new model improves the dynamic performance of the controller. Simulation and experimental results verify the proposed topology, its control and start-up strategy.

Temperature dependence of Lüders strain and its correlation with martensitic transformation in a medium Mn transformation-induced plasticity steel

The Luders deformation behavior in a medium Mn transformation induced plasticity （TRIP） steel is investigated at different temperatures ranging from 25 to 300 ℃. It demonstrates that the Ltiders band appears at all testing temperatures but with varied Luders strains which do not change monoton ically with temperature. The martensitic transformation is simultaneously observed within the Ltiders band in varying degrees depending on the testing temperature. It is well verified that the martensitic transformation is not responsible for the formation of Luders band, and a reasonable explanation is given for the non-monotonic variation of Luders strain with increasing temperature.

A thermodynamic model on predicting density of medium-Mn steels with experimental verification

A new model on predicting the density of hot-rolled multi-phased medium-Mn steel has been presen ted on the basis of thermodynamic calculations. This is an integrated model, which includes one for calculating the retained austenite （RA） fraction and the other for volume expansion during the aus tenite-to martensite transformation, because both of them are key parameters for calculating the den- sity of steel at ambient temperature. The existing empirical equations for calculating Mx temperature and lattice constants of both martensite and austenite have been all rcassessed by the XRD measure ments on the microstructures of seven hot-rolled medium-Mn steels. Finally, the densities ot seven steels were calculated merely from compositions and compared with the measured ones. The differ ence between them is no more than 1 %, suggesting that the presented model should be of good value in designing the low density steels.

The Averaged-value Model of a Flexible Power Electronics Based Substation in Hybrid AC/DC Distribution Systems

The concept of a flexible power electronics substation(FPES)was first applied in the Zhangbei DC distribution network demonstration project.As a multi-port power electronics transformer(PET)with different AC and DC voltage levels,the FPES has adopted a novel topology integrating modular multilevel converter(MMC)and four-winding medium frequency transformer(FWMFT)based multiport DC-DC converter,which can significantly reduce capacitance in each sub-module(SM)of a MMC and also save space and cost.In this paper,in order to accelerate speed of electromagnetic transient(EMT)simulations of FPES based hybrid AC/DC distribution systems,an averaged-value model(AVM)is proposed for efficient and accurate representation of FPES.Assume that all SM capacitor voltages are perfectly balanced in the MMC,then the MMC behavior can be modeled using controlled voltage sources based on modulation voltages from control systems.In terms of the averaged current transfer characteristics among the windings of the FWMFT,we consider that all multiport DC-DC converters are controlled with the same dynamics,a lumped averaged model using controlled current and voltage sources has been developed for these four-port DC-DC converters connected to the upper or lower arms of the MMC.The presented FPES AVM model has been tested and validated by comparison with a detailed IGBT-based EMT model.Results show that the AVM is significantly more efficient while maintaining its accuracy in an EMT simulation.