Micropores in G20Mn5N cast steel and their influence on stress distribution

To accurately analyze the impact of casting pores in steel,high-resolution 3D X-ray tomography technology was used to gather detailed statistical information about micropores.These micropores were classified as gas,shrinkage,and gas-shrinkage pores depending on their formation origin and morphology.Clustering tendencies and affinity parameters were defined to characterize the spatial correlations among these three types of pores.The 3D data from X-ray tomography scans were then integrated into finite element analysis(FEA)software to predict how micropore shape,size,and distribution influence stress distribution within the material.The results show that certain inflection points with small local radii within the cast pores are major contributors to stress concentration.Therefore,cast pores cannot be simply modeled as ideal spherical pores.The sphericity and volume of pores have a significant impact on the stress concentration of the model.Specifically,lower sphericity and larger pore volumes result in higher stress concentrations.Moreover,the internal pores of steel castings exhibit specific global distribution characteristics.Pores located on the surface of the specimen lead to significantly higher stress concentrations compared to those located inside the specimen.

Comparative Analysis of Statistical Thickness Models for the Determination of the External Specific Surface and the Surface of the Micropores of Materials: The Case of a Clay Concrete Stabilized Using Sugar Cane Molasses

In this work, four empirical models of statistical thickness, namely the models of Harkins and Jura, Hasley, Carbon Black and Jaroniec, were compared in order to determine the textural properties (external surface and surface of micropores) of a clay concrete without molasses and clay concretes stabilized with 8%, 12% and 16% molasses. The results obtained show that Hasley’s model can be used to obtain the external surfaces. However, it does not allow the surface of the micropores to be obtained, and is not suitable for the case of simple clay concrete (without molasses) and for clay concretes stabilized with molasses. The Carbon Black, Jaroniec and Harkins and Jura models can be used for clay concrete and stabilized clay concrete. However, the Carbon Black model is the most relevant for clay concrete and the Harkins and Jura model is for molasses-stabilized clay concrete. These last two models augur well for future research.

A Model of Steady-State Convective Combustion of Micropore Propellants

Aim To develop a physical and mathematical model related to micropore para- meters of steady-state convective combustion of micropore propellants(MPP). Methods The micropore parameters were measured by WXT-88 mage analysis apparatus and the convective combustion characteristic of MPP was measured by a large volume closed bomb, respectively. Rasults Statistical physical model of burning in the micropore and granular burning were developed. The burning rate equation of steady-state convective combustion of MPP was obtained. Conclusions This model correlates the convective burning rate with micropores para- meters for the first time,and the calculating values of convective burning rate are in agreement with test results.The model also can be used to estimate the effects of microporous parame- ters, basic mass burning rate, MPP density and pressure in combustion chamber on the convective combustion characteristics of MPP.

Characterizing the Micropores in Lacustrine Shales of the Late Cretaceous Qingshankou Formation of Southern Songliao Basin, NE China

Micropores of shale are significant to the gas content and production potential of shale, which has been verified in the research of marine shale gas; while, few studies have been conducted on lacustrine shales. This study collected 42 samples from three wells in the Late Cretaceous Qingshankou Formation of the southern Songliao Basin, NE China, and investigated these samples by the focused ion beam-scanning electron microscope(FIB–SEM) and nitrogen adsorption analysis techniques. Four types of micropores were identified in the samples, i.e., intergranular pore, intracellular pore, organic matter pore and microfracture. The pore structure type is characterized by open slit pores and "ink type" pores which are mainly 1.5–5 nm in diameter with mesopores as the main pores. The mesopores account for 74.01% of the pore volume and 54.68% of the pore surface area. Compared with the lacustrine shales from the Triassic Yanchang Formation in the Ordos Basin and Xujiahe Formation in the Sichuan Basin, the intergranular clay mineral interlayer pores are considered to be the main reservoir space for shale gas storage in the study area, followed by intraparticle pores, organic matter pores and microfractures. Maturity and micropore are the key controlling factors which affect the shale gas content of the Qingshankou Formation in southern Songliao Basin.

The nonlinear propagation of acoustic waves in a viscoelastic medium containing cylindrical micropores

Based on an equivalent medium approach, this paper presents a model describing the nonlinear propagation of acoustic waves in a viscoelastic medium containing cylindrical micropores. The influences of pores＇ nonlinear oscillations on sound attenuation, sound dispersion and an equivalent acoustic nonlinearity parameter are discussed. The calculated results show that the attenuation increases with an increasing volume fraction of micropores. The peak of sound velocity and attenuation occurs at the resonant frequency of the micropores while the peak of the equivalent acoustic nonlinearity parameter occurs at the half of the resonant frequency of the micropores. Furthermore, multiple scattering has been taken into account, which leads to a modification to the effective wave number in the equivalent medium approach. We find that these linear and nonlinear acoustic parameters need to be corrected when the volume fraction of micropores is larger than 0.1%.

A Universal Strategy For N-Doped 2D Carbon Nanosheets With Sub-Nanometer Micropore For High-Performance Supercapacitor

Preparing carbon nanosheets with precise control of open porous morphology via universal process and understanding the relationship between structure and capacitive performance are very urgent for achieving advanced supercapacitors.Herein,we propose a simple yet effective additive-free method to transform a bulk layered potassium phthalimide salt to novel nitrogen-doped twodimensional carbon sheets by self-activation during calcination.The obtained samples showed large-sized and flat structure with lateral size around 10μm,uniform sub-nanometer micropore size distribution of about 0.65 nm dimension,large specific surface area up to 2276.7 m^(2)g^(-1),and suitable nitrogen doping.Benefited from these merits,the optimized sample delivers a high specific capacitance of 345 F g^(-1)at 1 A g^(-1)and retains 270 F g^(-1)even at 50 A g^(-1)in6.0 M KOH electrolyte.Remarkably,the symmetric supercapacitor shows maximum energy densities of 16.43 Wh kg^(-1)and 23.6 Wh kg^(-1)in 6.0 M KOH and 1.0 M Na_(2)SO_(4)electrolytes,respectively.Importantly,on account the universality and simplicity of this method,the undoped as-prepared carbon sheet with uniform sub-nanometer micropore distribution can be synthesized from different potassium-containing salts with layered structure,which can be employed as a model for a deep understanding the effect of sub-nanometer micropores on capacitive performances.We find the number of micropores centered at 0.65 nm can be applied as one indicator to clarify the correlation between capacitance and critical pore size below 1 nm.

CONCENTRATION PARTITION OF PROTEIN SOLUTION IN A MICROPORE:EFFECT OF ELECTROSTATIC INTERACTION

A theory for calculating the electrostatic interaction between protein molecules and the wallof a liquid-filled micropore is established in terms of solving the Laplace and the linearPoisson-Boltzmann equations.The surface charge of protein molecules is measured by theelectrophoresis velocity,whilethe charge of the pore wall is obtained by the ionic Donnan equilibrium.The theory is then used to study the influence of solute-pore electrostatic interaction on theconcentration partition of protein solution in a micropore under different solution properties.Experi-mental verification is performed by detecting the hindered diffusion of bovine serum albumin in thetrack-etched polycarbonate membranes.A good consistence between the theoretical and experimentaldata is being achieved.

Growth of Casting Microcrack and Micropore in Single-crystal Superalloys Analysed by Three-Dimensional Unit Cell

Finite element （FE） analysis was employed to investigate the casting microcrack and micropore growth in nickel-base single-crystal superalloys DD3. Based on the finite deformation rate-dependent crystallographic constitutive equation, the simulations of casting microcrack and micropore growth in three-dimensional unit cell model were carried out in a range of parameters including stress triaxiality, Lode parameter and type of activated slip systems. The FE results show that the stress triaxiality has profound effects on growth behavior, and the Lode parameter is also important for the casting microcrack and micropore growth. The type of operative slip systems has remarkable effect on casting microcrack and micropore growth, so the life of single- crystal component is associated with the type of activated slip systems, which is related to Schmid factor and the number of activated slip systems. The growth comparison between microcrack and micropore reveals that when the material is subjected to large deformation, the growth rate of microcrack is faster than that of micropore, i.e. microcrack is more dangerous than micropore; the microcrack is easier to result in brittle fracture than micropore. The stress triaxiality and Lode parameter have strong influence on the growth of microcrack and micropore.

Effect of Thermal Treatment of the Hydroxyapatite Powders on the Micropore and Microstructure of Porous Biphasic Calcium Phosphate Composite Granules

The effect of thermal treatment of the hydroxyapatite powders on the micropore structure of porous biphasic calcium phosphate (BCP) granules was examined. The porous BCP granules could be attained through mixing and sintering/fracturing thermally treated 60 wt% hydroxyapatite powders and calcined 40 wt% β-tricalcium phosphate powders. The observed Scanning electron microscopy (SEM) morphologies showed that the density of micropores (0.1 - 2.0 μm) including interconnected micropores of the porous BCP granules mixed with hydroxyapatite powders thermally treated at 900°C was significantly improved and the composite particles of porous BCP granules were homogeneously mixed and distributed. This result indicates that the particles of hydroxyapatite powders that have a tendency to agglomerate at a room temperature were well isolated and dispersed through thermal treatment processing before mixing with calcined β-tricalcium phosphate powders. The microstructural characterizations such as phase purity and composition of porous BCP granules were performed and verified by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) analysis.

Characterization of cellulose acetate micropore membrane immobilized acylase Ⅰ

This paper describes an innovative method for the immobilization of acylase I, which was entrapped into the CA-CTA micropore membrane. The most suitable casting solutions proportion for immobilizing the enzyme was obtained through orthogonal experiment. Properties of the enzyme membrane were investigated and compared with those of free enzyme and blank membrane. The thermal stability and pH stability of the enzyme inside the membrane were changed by immobilization. The optimum pH was found to be 6.0, which changes 1.0 unit compared with that of free acylase I. The optimum temperature was found to be about 90℃, which is higher than that of free acylase I (60℃). Experimental results showed that immobilization had effects on the kinetic parameters of acylase I.

Micropores regulating enables advanced carbon sphere catalyst for Zn-air batteries

Energy conversion technologies like fuel cells and metal-air batteries require oxygen reduction reaction(ORR)electrocatalysts with low cost and high catalytic activity.Herein,N-doped carbon spheres(N-CS)with rich micropore structure have been synthesized by a facile two-step method,which includes the polymerization of pyrrole and formaldehyde and followed by a facile pyrolysis process.During the preparation,zinc chloride(ZnCl2)was utilized as a catalyst to promote polymerization and provide a hypersaline environment.In addition,the morphology,defect content and activity area of the resultant N-CS catalysts could be regulated by controlling the content of ZnCl2.The optimum N-CS-1 catalyst demonstrated much better catalytic activity and durability towards ORR in alkaline conditions than commercial 20 wt%Pt/C catalysts,of which the half-wave potential reached 0.844 V vs.RHE.When applied in the Zn-air batteries as cathode catalysts,N-CS-1 showed a maximum power density of 175 mW cm^(-2) and long-term discharging stability of over 150 h at 10 mA cm^(-2),which outperformed 20 wt%Pt/C.The excellent performance could be due to its ultrahigh specific surface area of 1757 m2 g
1 and rich micropore channels structure.Meanwhile,this work provides an efficient method to synthesize an ultrahigh surface porous carbon material,especially for catalyst application.

Conjugated microporous polymers-scaffolded enzyme cascade systems with enhanced catalytic activity

Enhancing catalytic activity of multi-enzyme in vitro through substrate channeling effect is promis-ing yet challenging.Herein,conjugated microporous polymers(CMPs)-scaffolded integrated en-zyme cascade systems(I-ECSs)are constructed through co-entrapping glucose oxidase(GOx)and horseradish peroxidase(HRP),in which hydrogen peroxide(H_(2)O_(2)) is the intermediate product.The interplay of low-resistance mass transfer pathway and appropriate pore wall-H_(2)O_(2) interactions facilitates the directed transfer of H_(2)O_(2),resulting in 2.4-fold and 5.0-fold elevation in catalytic activ-ity compared to free ECSs and separated ECSs,respectively.The substrate channeling effect could be regulated by altering the mass ratio of GOx to HRP.Besides,I-ECSs demonstrate excellent stabili-ties in harsh environments and multiple recycling.

Effect of carbon material and surfactant on ink property and resulting surface cracks of fuel-cell microporous layers

Ensuring the consistency of electrode structure in proton-exchange-membrane fuel cells is highly desired yet challenging because of wide-existing and unguided cracks in the microporous layer(MPL). The first thing is to evaluate the homogeneity of MPL with cracks quantitatively. This paper proposes the homogeneity index of a full-scale MPL with an area of 50 cm~2, which is yet to be reported in the literature to our knowledge. Besides, the effects of the carbon material and surfactant on the ink and resulting MPL structure have been studied. The ink with a high network development degree produces an MPL with low crack density, but the ink with high PDI produces an MPL with low crack homogeneity. The polarity of the surfactant and the non-polarity of polytetrafluoroethylene(PTFE) are not mutually soluble,resulting in the heterogeneous PTFE distribution. The findings of this study provide guidelines for MPL fabrication.

High-Performance Na-Ion Storage of S-Doped Porous Carbon Derived from Conjugated Microporous Polymers

Na-ion batteries(NIBs)have attracted considerable attention in recent years owing to the high abundance and low cost of Na.It is well known that S doping can improve the electrochemical performance of carbon materials for NIBs.However,the current methods for S doping in carbons normally involve toxic precursors or rigorous conditions.In this work,we report a creative and facile strategy for preparing S-doped porous carbons(SCs)via the pyrolysis of conjugated microporous polymers(CMPs).Briefly,thiophene-based CMPs served as the precursors and doping sources simultaneously.Simple direct carbonization of CMPs produced S-doped carbon materials with highly porous structures.When used as an anode for NIBs,the SCs exhibited a high reversible capacity of 440 mAh g?1 at 50 mA g?1 after 100 cycles,superior rate capability,and excellent cycling stability(297 mAh g?1 after 1000 cycles at 500 mA g?1),outperforming most S-doped carbon materials reported thus far.The excellent performance of the SCs is attributed to the expanded lattice distance after S doping.Furthermore,we employed ex situ X-ray photoelectron spectroscopy to investigate the electrochemical reaction mechanism of the SCs during sodiation-desodiation,which can highlight the role of doped S for Na-ion storage.

Preparation and Characterization of Microporous Nano-Tungsten Trioxide and Its Photocatalytic Activity after Doping Rare Earth

Aqueous sols and gels of tungstic acid were prepared from Na2WO4 with protonated cation-exchange resin. Nano-tungsten oxide of a microporous lamella was synthesized by means of washing of WO3· 2H2O with distilled water under ultrasonic wave agitation and centrifuging repeatedly, and the specific surface area tended to increase gradually with washing and centrifuging. The sample of centrifuged 7 h has more than 2 times highs specific surface area and more high photocatalytic activity . The mechanisms are also discussed.

Facile synthesis of microporous carbon through a soft-template pathway and its performance in desulfurization and denitrogenation

Wormlike/lamellar microporous carbons were prepared by using long alkyl chain primary amine hydrochloride as the template and resorci- nol/formaldehyde as the carbon source under highly acidic conditions. The template can be eliminated by high temperature treatment under an inert atmosphere. The obtained carbon materials were characterized by N2 adsorption-desorption, transmission electron microscopy, ther- mogravimetry and scanning electron microscopy. The results show that dodecylamine hydrochloride surfactant can be used as the template of wormlike micropores structure while octadecylamine hydrochloride results in both lamellar and wormlike micropores. The obtained carbon materials have the similar pore size in the range of 0.5-0.59 nm, but with various morphologies such as monolith, spheres, and coralline. The microporous carbon obtained from dodecylamine hydrochloride surfactant shows good adsorption performance to remove the refractory sulfur compounds and nitrogen-containing compounds in fuel.

Surface Modification of Polypropylene Microporous Membrane by Atmospheric-Pressure Plasma Immobilization of N,N-dimethylamino Ethyl Methacrylate

Surface modification of polypropylene microporous membrane （PPMM） was performed by atmospheric pressure dielectric barrier discharge plasma immobilization of N,Ndimethylamino ethyl methacrylate （DMAEMA）. Structural and morphological changes on the membrane surface were characterized by attenuated total reflection-Fourier transform infrared spectroscopy （FT-IR/ATR）, X-ray photoelectron spectroscope （XPS） and field emission scanning electron microscopy （FE-SEM）. Water contact angles of the membrane surfaces were also measured by the sessile drop method. Results reveal that both the plasma-treating conditions and the adsorbed DMAEMA amount have remarkable effects on the immobilization degree of DMAEMA. Peroxide determination by 1,1-diphenyl-2-picrvlhydrazyl （DPPH） method verifies the exsistence of radicals induced by plasma, which activize the immobilization reaction. Pure water contact angle on the membrane surface decreased with the increase of DMAEMA immobilization degree, which indicates an enhanced hydrophilicity for the modified membranes. The effects of immobilization degrees on pure water fluxes were also measured. It is shown that pure water fluxes first increased with immobilization degree and then decreased. Finally, permeation of bovine serum albumin （BSA） and lysozyme solution were measured to evaluate the antifouling property of the DMAEMA-modified membranes, from which it is shown that both hydrophilicity and electrostatic repulsion are beneficial for membrane antifouling.

Improvement of antifouling characteristics in a bioreactor of polypropylene microporous membrane by the adsorption of Tween 20

Surface modification by physical adsorption of Tween 20 was accomplished on polypropylene microporous membranes （PPMMs）. Attenuated total reflection-Fourier transform infrared spectroscopy （ATR/FT-IR） and field emission scanning electron microscope （FE- SEM） were used to characterize the chemical and morphological changes on the membrane surfaces. Water contact angles and relative pure water fluxes were measured. The data showed that the hydrophilic performance for the modified membranes increased with the increase in the adsorption amount of Tween 20 onto the surface or into the pores of polypropylene microporous membranes. To test the antifouling property of the membranes by the adsorption of Tween 20 in a membrane bioreactor （MBR）, filtration for active sludge was performed using synthetic wastewater. With the help of the data of water fluxes and the FE-SEM photos of the modified PPMMs before or after operating in a MBR for about 12 d, the PPMMs with monolayer adsorption of Tween 20 showed higher remained flux and stronger antifouling ability than unmodified membrane and other modification membranes studied.

SURFACE MODIFICATION OF POLYPROPYLENE MICROPOROUS MEMBRANES BY THE ADSORPTION OF NON-IONIC SURFACTANTS

Surface modification by physical adsorption of a series of non-ionic surfactants including Tween 20, Tween 40, Tween 60, Tween 80 and Tween 85, was accomplished on polypropylene microporous hollow fiber and flat membranes. The adsorption curve of the membrane surface was analyzed by weight measurements and the typical results showed a twoplatform character similarly. Differences in the degree and curve shape of adsorption resulting from such factors as concentration, temperature, as well as water cleaning time were observed for Tween 85 among other Tweens. Attenuated total reflection - Fourier transform infrared spectroscopy analysis and field emission scanning electron microscopy observation showed that the adsorption of Tween on polypropylene microporous membrane （PPMM） is effective and occurs mainly in the pores of PPMMs at low adsorption amount, and on the membrane surface also at high adsorption value.

Surface Modification of Polypropylene Microporous Membrane by Atmospheric-pressure Plasma Induced N-vinyl-2-pyrrolidone Graft Polymerization

Membrane surfaces modified with poly（N-vinyl-2-pyrrolidone） （PNVP） can be endowed with hydrophilicity, biocompatibility and functionality. In this work, atmospheric pressure dielectric barrier discharge plasma graft polymerization of N-vinyl-2-pyrrolidone （NVP） onto polypropylene （PP） microporous membrane surface was studied. The experimental results reveal that plasma treatment conditions, such as discharge power, treatment time and adsorbed NVP amount, have remarkable effects on the grafting degree of NVP. Structural and morphological changes on the membrane surfaces were characterized by attenuated total reflection-Fourier transform infrared spectroscopy （FT-IR/ATR）, X-ray photoelectron spectroscope （XPS） and field emission scanning electron microscopy （FE-SEM）. Water contact angles of the membrane surfaces were also measured by the sessile drop method. Water contact angles on the membrane surfaces decrease with the increase of NVP grafting degree, which indicates an enhanced hydrophilicity for the modified membranes. The effects of grafting degrees on pure water fluxes were also measured. It is shown that pure water fluxes increase with grafting degree firstly and then decrease adversely. Finally, filtration of bovine serum albumin （BSA） solution and platelets adhesion of the PNVP modified membranes show good protein resistance and potential biocompatibility due to the enhancement of surface hydrophilicity.