Microstructure and Properties of AlCoCrFeNiTi High-Entropy Alloy Coatings Prepared by Laser Cladding

21-4N(5Cr21Mn9Ni4N)is extensively employed in the production of engine valves,operating under severe conditions.Apart from withstanding high-temperature gas corrosion,it must also endure the impact of cylinder explosion pressure.The predominant failure mode of 21-4N valves is abrasive wear.Surface coatings serve as an effective approach to prevent such failures.In this investigation,Laser cladding technology was utilized to fabricate AlCoCrFeNiTi high entropy alloy coatings onto the surfaces of 21-4N valves.According to the findings,the cladding zone has a normal dendritic microstructure,a good substrate-to-cladding layer interaction,and no obvious flaws.In terms of hardness,the cladding demonstrates an average hardness of 620 HV.The hardness has increased by 140%compared to the substrate.The average hardness of the cladding remains at approximately 520 HV even at elevated temperatures.Regarding frictional wear performance,between 400℃and 800℃,the cladding layer exhibits an average friction coefficient of 0.4,with the primary wear mechanisms being abrasive wear,adhesive wear,and a minor degree of plastic deformation.

Influences of oxide content and sintering temperature on microstructures and mechanical properties of intragranular-oxide strengthened iron alloys prepared by spark plasma sintering

How to increase strength without sacrificing ductility has been developed as a key goal in the manufacture of high-performance metals or alloys. Herein, the double-nanophase intragranular yttrium oxide dispersion strengthened iron alloy with high strength and appreciable ductility was fabricated by solution combustion route and subsequent spark plasma sintering, and the influences of yttrium oxide content and sintering temperature on microstructures and mechanical properties were investigated. The results show at the same sintering temperature,with the increase of yttrium oxide content, the relative density of the sintered alloy decreases and the strength increases. For Fe–2wt%Y_(2)O_(3)alloy, as the sintering temperature increases gradually, the compressive strength decreases, while the strain-to-failure increases. The Fe–2wt%Y_(2)O_(3)alloy with 15.5 nm Y_(2)O_(3)particles uniformly distributed into the 147.5 nm iron grain interior sintered at 650℃ presents a high ultimate compressive strength of 1.86 GPa and large strain-to-failure of 29%. The grain boundary strengthening and intragranular second-phase particle dispersion strengthening are the main dominant mechanisms to enhance the mechanical properties of the alloy.

Production,Properties and Microstructures of Mg-RE-Zn-Zr(RE=MM,Nd) Alloy

The Mg-MM and Mg-Nd master alloys were prepared through the ingot metallurgy method under the protection of a special flux. The thermodynamic behaviors of different rare earth elements in the molten Mg alloys were investigated. Two experimental alloys, Mg-3.0 wt pct MM-0.7 wt pct Zn-0.7 wt pct Zr and Mg-2.8 wt pct Nd-0.7 wt pct Zn-0.7 wt pct Zr, were prepared. The hardness and tensile properties of experimental alloys were measured and the microstructures were observed. The results showed that the rare earth elements could react greatly with the Mg chloride in the flux. The Mg-Nd-Zn-Zr alloy displayed a good aging hardening effect. The dispersed metastable phase ? (Mg3Nd) is an important strengthening phase to improve the tensile properties of this alloy. So the Mg-Nd-Zn-Zr alloy has better tensile properties and elongation than those of the Mg-MM-Zn-Zr alloy, and the ductile fracture character could be observed. The microvoid coalescence is the dominant fracture mechanism in this alloy.

Effects of Technological Parameters on Microstructures and Properties of Low Cost Hot Rolled Dual-Phase Steel on CSP Line

The effects of technological parameters on microstructures and properties of low cost hot rolled dual-phase steel was researched by design different finish rolling temperature,mid cooling temperature between laminar cooling and UFC (ultra fast cooling) and stable UFC rate on the same gauge strips with the same chemistry composition during the manufacture process.It is the key for controlling coil temperature to control finish rolling temperature and mid cooling temperature between laminar cooling and UFC that based on stable UFC rate precondition.The lower finish rolling temperature,with mid cooling temperature between laminar cooling and UFC,the better to form martensite is.The foundation of developing the similar productions on the similar product line was supplied.It is good to technological advancement of developing high affixation value production as hot rolled DP steel,TRIP steel etc.in CSP line.

Mechanism of Effects of Rare Earths on Microstructure and Properties at Elevated Temperatures of AZ91 Magnesium Alloy

By using real-space recursion method,the energetics of the undoped and Al and/or RE atoms doped 7（1450）〈0001〉 symmetric tilt grain boundaries（GBs）in AZ91 alloys were investigated.Similar calculations were performed on undoped and doped bulk α Mg for comparison.The results showed that Al atoms segregated at GBs in AZ91 alloys.When RE atoms were added,they also segregated at GBs,and their segregation is stronger than Al atoms＇.Therefore,RE atoms retard the segregation of Al atoms.Calculations of interaction energy indicated that Al atoms repelled each other,and could form ordered phase with host Mg atoms.On the contrary to the case of Al,RE atoms attracted each other,they could not form ordered phase with Mg,but could form clusters.Between RE and Al,there existed attractive interaction,and this attractive interaction was the origin of Al11RE3 precipitation.Precipitation of Al11RE3 particles with high melting point and high thermal stability along GB improves high temperature properties of AZ91 alloys.

Effects of Dysprosium Oxide Doping on Microstructure and Properties of Barium Titanate Ceramic

Different amounts of dysprosium oxide were incorporated into barium titanate powders synthesized by hydrothermal method. Relations of substitution behaviors and lattice parameters with solid-solubility were studied. Furthermore, the influences of dysprosium oxide doping fraction on grain size and dielectric properties of barium titanate ceramic, including dielectric constant and breakdown electric field strength , were investigated via scanning electron microscope, X-ray diffraction and electric property tester. The results show that dysprosium oxide can restrain abnormal grain growth during sintering and that fine-grained and high density of barium titanate ceramic can result in excellent dielectric properties. As mass fraction of dysprosium oxide is 0.6%, the lattice parameters of grain increase to the maximum because of the lowest vacancy concentration. The electric property parameters are cited as following： dielectric constant （25 ℃ ） reaches 4100, the change in relative dielectric constant with temperature is - 10% to 10% within the range of - 15 - 100 ℃, breakdown electric field strength （alternating current） achieves 3.2 kV·mm^-1, which can be used in manufacturing high voltage ceramic capacitors

Modeling of Microstructure Evolution and Mechanical Properties of Steel Plates Produced by Thermo-Mechanical Control Process and Its On-line Application

An integrated metallurgical model was developed to predict microstructure evolution and mechanical properties of low-carbon steel plates produced by TMCP. The metallurgical phenomena occurring during TMCP and mechanical properties were predicted for different process parameters. In the later passes full recrystallization becomes difficult to occur and higher residual strain remains in austenite after rolling. For the reasonable temperature and cooling schedule, yield strength of 30 mm plain carbon steel plate can reach 310 MPa. The first on-line application of prediction and control of microstructure and properties (PCMP) in the medium plate production was achieved. The predictions of the system are in good agreement with measurements.

Microstructure and Properties of Plasma Spraying Boron Carbide Coating

Microstructure of plasma spray boron carbide coating was studied by SEM and TEM. Its physical, mechanical and electrical properties were measured. The results showed that high microhardness, modulus and low porosity of B4C coating were manufactured by plasma spray. It was lamellar packing and dense. The B4C coating examined here contained two principal structures and two impurity phase besides major phase. The relatively small value of Young's modulus, comparing with that of the bulk materials, is explained by porosity . The Fe impurity phase could account for the relatively high electrical conductivity of boron carbide coating by comparing with the general boron carbide materials.

The influence of preheating on microstructure and properties of the cladding layer with plasma arc powder surfacing

In this paper, the influence of preheating on the layer microstructure and properties is analyzed in the layer metal microstructure. The influence of preheating temperature on the shape and amount of primary carbides and borides little, but on initial γ-dendrites is large. With the increasing of preheating temperature, little by little the γ-dendrites , which grown from parent material to layer, are flourishing to disappearing, and the microhardness at the center of the layer is increasing.

STUDY ON HEAT-TREATMENT OF AIN/SiC_w COMPOSITES AND EFFECTS ON MICROSTRUCTURE AND PROPERTIES

AlN-SiC whisker composites with Y2O3 and SiO2 additives were heat-treated at 1300 ℃ in air. The phase composition and microstrurture were analyzed using XRD, SEM and HREM techniques to study the effect of heat-treatment on the microstructure and properties of the composites. The results reveal that the mechanical properties and high temperature oxidation resistance of the composite of ivhich additives composition approaches the eutectic point of Y2O3-SiO2 can be improved through the heat-treatment. Glass phase in the grain boundary is observed to react with the surface composition of AlN forming fibrous 2Hδ Sialon, resulting a crossing structure produced by fibrous 2Hδ Sialon and SiC whiskers.

Comparison of microstructure and properties between joints of FSW and TIG 316L austenitic stainless steel

FSW and TIG were conducted on 316L stainless steel.Variation during microstructure and properties in joints obtained by different welding methods was studied.The results show that the effect of severe mechanical stirring and intense plastic deformation creat a fine recrystallized grain in the welding joint during FSW.As for TIG,the temperature of welding joint exceeds the melting point of welded material itself.The entire welding process belongs to the solidification of a small molten pool;and the microstructure of the joint takes on a typical casting structure.When the welding parameters were selected appropriately,the average ultimate tensile strength of FSW joints can reach 493 MPa,which is 83.6%of base metal;the average elongation is 52.1%of base metal.The average ultimate tensile strength of TIG joints is 475 MPa, which is 80.5%of base metal;the average elongation is 40.8%of base metal.The tensile test of FSW joints is superior to the TIG joints.The microhardness of FSW joint compared to base metal and TIG joint having a significant improvement,which arel95.5 HV,159.7 HV and 160.7 HV,respectively;grain refinement strengthening plays an important role in enhancing the microhardness.The electrochemical corrosion tests show that the joint of FSW 316L austenitic stainless steel has a good corrosion resistance.

Additive manufacturing of magnesium and its alloys: process-formabilitymicrostructure-performance relationship and underlying mechanism

Magnesium and its alloys,as a promising class of materials,is popular in lightweight application and biomedical implants due to their low density and good biocompatibility.Additive manufacturing(AM)of Mg and its alloys is of growing interest in academia and industry.The domain-by-domain localized forming characteristics of AM leads to unique microstructures and performances of AM-process Mg and its alloys,which are different from those of traditionally manufactured counterparts.However,the intrinsic mechanisms still remain unclear and need to be in-depth explored.Therefore,this work aims to discuss and analyze the possible underlying mechanisms regarding defect appearance and elimination,microstructure formation and evolution,and performance improvement,based on presenting a comprehensive and systematic review on the relationship between process parameters,forming quality,microstructure characteristics and resultant performances.Lastly,some key perspectives requiring focus for further progression are highlighted to promote development of AM-processed Mg and its alloys and accelerate their industrialization.

Microstructure and property research on welded joints of 7xxx aluminum alloy welding wire TIG for 7075 aluminum alloy

7 xxx welding wire was self-made by spray forming ingots drawn to series welding wires products,and then TIG butt welding test is used for 5 mm thick 7075 high-strength aluminium alloy.After welding,the stress relief+solid-solution aging heat treatment(T6)were performed to joints,and the mechanical properties and microstructure of the joints before and after heat treatment were comparative analyzed.The results show that the properties of the heat-affected zone(HAZ)of the joint before heat treatment decreas,and the joint is softened.The welded joints tensile strength is 271.8 MPa,the elongation is 5.6%,and the average hardness of the weld is 118.4 HV.The second phase particles such asη(Mg Zn2),S(Al2 Cu Mg),Al13 Fe4 are distributed in a network layer,with no apparent element segregation.After heat treatment,the structure of each area of the joint is coarsened,and a small amount of Fe-containing impurity phases are distributed.Theηand S phases are dissolved in the matrix.The hardness of each area of the joint is increased to 155 HV,and the softening zone is disappeared,this leads the joint elongation close to 16.9%.The tensile strength is increased to 511.8 MPa,reaching 94%of the base metal tensile strength.

Preparation and characterization of organic pigments and their fluorescence properties depending on bulk structure

Fluorescent pigments, based on the optical or electrooptical properties of dyes, are the main component in fluorescent coatings and inks. In this study, three kinds of dyes（Rhodamine B, Light Green SF Yellowish, Coumarin） with four different ratios（2.5 wt%, 3 wt%, 3.5 wt%, 4 wt%） were employed as luminophor,and the melamine-formaldehyde（MF） resin was used as curing resin to prepare fluorescent pigments in different color. Fourier transform infrared spectroscopy and X-ray diffractometry were carried out to analyze the structure of the fluorescent pigments. Scanning electron microscopy and particle size distribution were used to present the morphology of fluorescent pigments. UV–vis and fluorescence spectrum were used to demonstrate the optical properties. It can be concluded that, coumarin pigments possessed consecutive structure in MF resin while rhodamine B might be the best for the preparation of printing inks among the three kinds of dyes from the view of particle size. The TG results presented that all the pigments showed good thermal stability, which might possess potential application in high speed printing industry.

Effect of Graphene Nanoplate and Silicon Carbide Nanoparticle Reinforcement on Mechanical and Tribological Properties of Spark Plasma Sintered Magnesium Matrix Composites

Processing of magnesium （Mg） matrix composites reinforced with low reinforcement content （up to 4-5 vol.%） of graphene nanoplates （GNPs） and silicon carbide （SIC） nanoparticles using bait milling and spark plasma sintering （SPS） is reported. Near full densification was observed for all the composite compositions at the sintering temperature of 450 ~C （soaking time of 5 min and applied pressure of 50 MPa）. Detailed analysis of the microstructure and mechanical and tribological （under dry sliding contact with alumina counter-face） properties with reinforcement content in Mg-GNP and Mg-SiC is presented. Mg-GNP and Mg-SiC composites reinforced with about 2 vol.% of reinforcement content exhibited significant improvement in microhardness and wear resistance as compared with Mg compacts.

Microstructure and properties of Al–7Si–0.6Mg alloys with different Ti contents deposited by wire arc additive manufacturing

Numerous studies have addressed the advantages of wire arc additive manufacturing for manufacturing aluminum alloys. However, the role of Ti content in aluminum alloys has rarely been discussed. Herein, the effect of Ti content on the microstructure and properties of Al–7 Si–0.6 Mg alloys was studied. The alloys were deposited via wire arc additive manufacturing and were examined through optical microscopy(OM), scanning electron microscopy(SEM), and electronic universal testing. The results show that the increase of Ti content gradually promotes the increase of the secondary dendrite arm spacing and also has an increasing tendency to form pores defect in the as-deposited alloys. The change of titanium content also affects the difference between horizontal and vertical direction properties of the alloy. The alloy with a Ti content of 0.112 wt% exhibits the best comprehensive properties. There is no difference in its horizontal and vertical direction properties. The tensile strengths, yield strengths, and elongation of this alloy(T6) along the vertical and horizontal axis are 356 and 355 MPa, 307 and308 MPa, and 8.5% and 8.0%, respectively.

Effects of N and/or S Doping on Structure and Photocatalytic Properties of BiOBr Crystals

The BiOBr crystals doped with N and/or S have been prepared by a facile and rapid solvothermal method using urea and/or thiourea as doped resource. The morphologies and structures of the as-prepared samples were characterized by SEM, TEM, XRD, XPS and PL spectrum. Their electronic structures have been investigated and discussed using first principles based on the density functional theory. The photocatalytic properties of the products can be adjusted by the content and species of dopants.

Laser Oscillating of Nickel Alloyed Welds on Press‑Hardened Steel

Laser oscillating welding was employed to fabricate Al-Si coated press-hardened steel(PHS)to improve the element homogeneity in the fusion zone.Laser oscillating welding was employed with various oscillation amplitudes(0 mm,0.5 mm and 1.3 mm)in this present.Ni foil of 0.06 mm thickness was used as an interlayer between two tailored PHS welded.The weld morphology,elemental profile,microstructure and tensile strength of welded joints were studied.The results showed that full penetration weld without any weld defects were achieved for any oscillation amplitudes,and weld width increased with increasing oscillation amplitudes.With the oscillation amplitudes increased,Ni and Al had an uneven elemental profile due to strong stirring force,but the Ni and Al content in the weld was decreased and Ni had a sharp descent compared to Al element.Only fewδ-ferrite was presented in fusion line with the oscillation amplitudes increased to 1.3 mm.The oscillation amplitudes did not have an effect on the tensile properties,which was similar to that of base metal.But if keeping increasing the oscillation amplitudes or reducing the thickness of Ni interlayer,it has a potential risk to form more and moreδferrite such that deteriorate the mechnical properties of welded joints.

Electron Beam-Physical Vapor Deposited TiAl-based Laminated Composite Sheet with Nb Layer Toughening

The TiAl-based laminated composite sheet of 150 mm × 100 mm × 0.2 mm, with 24 TiAl layers and 23 Nb layers laid alternately one on another, was successfully fabricated using the electron beam-physical vapor deposition （EB-PVD） method. The microstructure and properties of the sheet were investigated on an atomic force microscope （AFM）, a scanning electron microscope （SEM） and a tensile testing machine. The results indicate that the evenly distributed Nb layers are well joined with the TiAl layers, and the interfaces between layers are transparent, and every interlayer spacing is of about 8μm. The fractures appear to be a mixture of intergranular fractures and somewhat ductile quasi-cleavage ones. Despite its slight influence on ultimate tensile strength, the inserts of Nb layers efficiently increase the room temperature ductility of TiAl-based alloys due to the crack deflection effect.