The preparation of γ-Fe<sub>2</sub>O<sub>3</sub>/Gd<sub>2</sub>O<sub>3</sub> nanocomposite for possible use in magnetic hyperthermia application was done by ball millin...The preparation of γ-Fe<sub>2</sub>O<sub>3</sub>/Gd<sub>2</sub>O<sub>3</sub> nanocomposite for possible use in magnetic hyperthermia application was done by ball milling technique. The nanocomposite was characterized by X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). The heating efficiency and the effect of milling time (5 h and 30 h) on the structural and magnetic properties of the nanocomposite were reported. XRD analysis confirms the formation of the nanocomposite, while magnetization measurements show that the milled sample present hysteresis with low coercivity and remanence. The specific absorption rate (SAR) under an alternating magnetic field is investigated as a function of the milling time. A mean heating efficiency of 68 W/g and 28.7 W/g are obtained for 5 h and 30 h milling times respectively at 332 kHz and 170 Oe. The results showed that the obtained nanocomposite for 5 h milling time is a promising candidate for magnetic hyperthermia due to his properties which show an interesting magnetic behavior and high specific absorption rate.展开更多
Introduction: Noise is the second leading cause of hearing loss in adults after presbycusis. The objective of this work was to study hearing loss induced by the noise of mills in the markets of Parakou. Methods: This ...Introduction: Noise is the second leading cause of hearing loss in adults after presbycusis. The objective of this work was to study hearing loss induced by the noise of mills in the markets of Parakou. Methods: This was a descriptive and analytical cross-sectional study, conducted from February 3 to June 3, 2021 in the markets of Parakou. It concerned millers and sellers located within a 5 meter radius around the mills and among whom pure-tone audiometry was performed to detect a hearing loss. Subjects with no particular medical health history, under 55 years of age and having been working in these markets since more than 12 months, were included. Results: In this study, 103 subjects were selected, including 43 millers and 61 sellers. Their average age was 29 ± 13 years. The sex ratio was 0.49. The average length of service in the profession was 8 years with the extremes of 3 months and 47 years. They were exposed to noise on average 10 hours per day and 6 days a week. The average duration of weekly noise exposure was 23 h 28 min ± 13 h 32 min with the extremes of 5 h 00 min and 52 h 30 min. The average level of noise exposure was 90 dB with the extremes of 72 and 110 dB. 24 subjects reported symptoms related to noise such as headache, tinnitus, and hearing loss, with respective proportions of 22.33%, 20.39% and 06.80%. The prevalence of noise-related hearing loss was 26.21% (n = 27/103). Subjects with a notch at 4000 Hz and normal Average Hearing Loss (AHL) (20.39%) had a seven-time greater risk of developing noise-induced hearing loss (OR = 6.58;95% CI [2.54 - 18.8], p Conclusion: Hearing loss related to the noise of mills affected both millers and sellers near the mills in markets, hence the importance of regulating mills.展开更多
The effects of the milling parameters involving shape of powder particles, rotation speed, and ball-to-powder diameter (BPDR) on DEM modeling in the planetary ball mill were investigated. BPDR was varied from 1 to 10....The effects of the milling parameters involving shape of powder particles, rotation speed, and ball-to-powder diameter (BPDR) on DEM modeling in the planetary ball mill were investigated. BPDR was varied from 1 to 10. The results revealed that the size and shape of the powder particles do not give a significant change in simulation results when BPDR attains maximum value of 10. The increasing of BPDR leads to the increase of simulation time and size. Hence, the effect of change of the powder particle shape on the calculated data size is not significant. The results also revealed that the increasing rotation speed increases impact energy between powder particles.展开更多
The olive mill waste waters (OMWW) generated from olive oil extraction is a major environmental concern since they are characterized by their role as a pollutant (high organic and mineral matters) and their pH acid. T...The olive mill waste waters (OMWW) generated from olive oil extraction is a major environmental concern since they are characterized by their role as a pollutant (high organic and mineral matters) and their pH acid. The aim of this study was to valorize (OMWW) by anaerobic fermentation in the presence of cow manure in order to produce biogas and reduce their toxic load. Many tests were carried out by fermenting (OMWW) with polyphenols in the presence of cow manure in thermophile temperatures. The performance of this treatment was valuated through measurements of biogas production and by the determination of different parameters of fermented media (pH, volume of the biogas and polyphenols).展开更多
Many new types of rolling mills have been studied and developed corresponding to the needs of improvement in productivity and quality.This presentation reflects back at some of the innovative technologies,which were d...Many new types of rolling mills have been studied and developed corresponding to the needs of improvement in productivity and quality.This presentation reflects back at some of the innovative technologies,which were developed by Mitsubishi-Hitachi Metals Machinery,Inc.(hereinafter referred to as M-H),including the evolution of the pair cross mill,mill stabilizing device,on-line roll profiler,shape meter for hot-rolling,endless hot-rolling, recent application of UCM,and M-H split housing type 20-high mill.展开更多
The effects of moisture content （8%, 10%and 12%）, variety （Tarom and Fajr） and parboiling on milling quality of rice as a function of milling recovery （MR）, head rice yield （HRY）, degree of milling （DOM） and...The effects of moisture content （8%, 10%and 12%）, variety （Tarom and Fajr） and parboiling on milling quality of rice as a function of milling recovery （MR）, head rice yield （HRY）, degree of milling （DOM） and whiteness were investigated. The parboiled grains was prepared with three soaking temperatures of 25 oC, 50 oC and 75 oC and three steaming times of 10, 15 and 20 min. As a result of parboiling, the increasing rates of MR and HRY values were 7.8%and 14.3%for Tarom and 9.8%and 10.0%for Fajr, respectively, and the decreasing rates for DOM and whiteness were 6.6%and 10.8%for Tarom and 6.8% and 10.5% for Fajr, respectively. Moreover, decreasing moisture content to 8%maximized MR （75.8% for Tarom and 74.3% for Fajr） and HRY （65.8% for Tarom and 57.0% for Fajr） while increasing that to 12%revealed maximum values of DOM （6.1%for Tarom and 6.2%for Fajr） and whiteness （24.8%for Tarom and 28.2%for Fajr）.展开更多
In this paper, the milling parameters of high energy ball mill (Fritsch Pulverisette 7) like vial geometry, number and size of balls and speed of the mill were modelled and discussed. Simulations through discrete elem...In this paper, the milling parameters of high energy ball mill (Fritsch Pulverisette 7) like vial geometry, number and size of balls and speed of the mill were modelled and discussed. Simulations through discrete element method (DEM) provide correlation between the milling parameters. A mathematical model is used to improve and develop this process. The results show that the loss of powder mass can remarkably improve the performance of milling. The balls made of stainless-steel have a positive effect on the milling efficiency. The simulation shows that the high ball milling velocities can contribute to faster particle size reduction.展开更多
Grinding (Particle size reduction) of biomass is an age-long operation that is performed during the preparation process of certain food products. Among the grinding mill machines mostly used for this operation are ham...Grinding (Particle size reduction) of biomass is an age-long operation that is performed during the preparation process of certain food products. Among the grinding mill machines mostly used for this operation are hammer mill and disk mill. Being that the nature of biomass affects the performance and choice of grinding-mill machine to be adopted, it is imperative to compare and select appropriate grinding mill machine that is efficient and effective. In this paper, a comparative technique to evaluate and select appropriate grinding mill machine for particle size reduction of dried white yam (Dioscorea rotundata) is proposed. Hammer mill and disk mill machines were selected for consideration. Two white yam species (Benue and Delta Yam) were prepared into dried chips and ground using the selected mills. Among the attribute (performance parameters) considered are crushing time, particle size distribution and energy consumed. A measure of performance (Index I) based on the comparative technique was formulated and used in evaluating the performance of the two mills. In the hammer mill, index I recorded 2721.2 and 3719.82 par/kWh for Benue Yam chips at screen size 4 and 6 mm, respectively, while 2647.89 and 3472.01 par/kWh was recorded for Delta yam chips at screen size 4 and 6 mm, respectively. Index I values for the Disk mill were 2536.25 and 2433.42 par/kWh at 1.2 mm clearance distance for Benue Yam chips and Delta Yam chips, respectively. The results indicated that hammer mill performed better overall than the disk mill. The comparative technique was found suitable in the evaluation of the performance of the mills. It is recommended that hammer mill be adopted.展开更多
文摘The preparation of γ-Fe<sub>2</sub>O<sub>3</sub>/Gd<sub>2</sub>O<sub>3</sub> nanocomposite for possible use in magnetic hyperthermia application was done by ball milling technique. The nanocomposite was characterized by X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). The heating efficiency and the effect of milling time (5 h and 30 h) on the structural and magnetic properties of the nanocomposite were reported. XRD analysis confirms the formation of the nanocomposite, while magnetization measurements show that the milled sample present hysteresis with low coercivity and remanence. The specific absorption rate (SAR) under an alternating magnetic field is investigated as a function of the milling time. A mean heating efficiency of 68 W/g and 28.7 W/g are obtained for 5 h and 30 h milling times respectively at 332 kHz and 170 Oe. The results showed that the obtained nanocomposite for 5 h milling time is a promising candidate for magnetic hyperthermia due to his properties which show an interesting magnetic behavior and high specific absorption rate.
文摘Introduction: Noise is the second leading cause of hearing loss in adults after presbycusis. The objective of this work was to study hearing loss induced by the noise of mills in the markets of Parakou. Methods: This was a descriptive and analytical cross-sectional study, conducted from February 3 to June 3, 2021 in the markets of Parakou. It concerned millers and sellers located within a 5 meter radius around the mills and among whom pure-tone audiometry was performed to detect a hearing loss. Subjects with no particular medical health history, under 55 years of age and having been working in these markets since more than 12 months, were included. Results: In this study, 103 subjects were selected, including 43 millers and 61 sellers. Their average age was 29 ± 13 years. The sex ratio was 0.49. The average length of service in the profession was 8 years with the extremes of 3 months and 47 years. They were exposed to noise on average 10 hours per day and 6 days a week. The average duration of weekly noise exposure was 23 h 28 min ± 13 h 32 min with the extremes of 5 h 00 min and 52 h 30 min. The average level of noise exposure was 90 dB with the extremes of 72 and 110 dB. 24 subjects reported symptoms related to noise such as headache, tinnitus, and hearing loss, with respective proportions of 22.33%, 20.39% and 06.80%. The prevalence of noise-related hearing loss was 26.21% (n = 27/103). Subjects with a notch at 4000 Hz and normal Average Hearing Loss (AHL) (20.39%) had a seven-time greater risk of developing noise-induced hearing loss (OR = 6.58;95% CI [2.54 - 18.8], p Conclusion: Hearing loss related to the noise of mills affected both millers and sellers near the mills in markets, hence the importance of regulating mills.
文摘The effects of the milling parameters involving shape of powder particles, rotation speed, and ball-to-powder diameter (BPDR) on DEM modeling in the planetary ball mill were investigated. BPDR was varied from 1 to 10. The results revealed that the size and shape of the powder particles do not give a significant change in simulation results when BPDR attains maximum value of 10. The increasing of BPDR leads to the increase of simulation time and size. Hence, the effect of change of the powder particle shape on the calculated data size is not significant. The results also revealed that the increasing rotation speed increases impact energy between powder particles.
文摘The olive mill waste waters (OMWW) generated from olive oil extraction is a major environmental concern since they are characterized by their role as a pollutant (high organic and mineral matters) and their pH acid. The aim of this study was to valorize (OMWW) by anaerobic fermentation in the presence of cow manure in order to produce biogas and reduce their toxic load. Many tests were carried out by fermenting (OMWW) with polyphenols in the presence of cow manure in thermophile temperatures. The performance of this treatment was valuated through measurements of biogas production and by the determination of different parameters of fermented media (pH, volume of the biogas and polyphenols).
文摘Many new types of rolling mills have been studied and developed corresponding to the needs of improvement in productivity and quality.This presentation reflects back at some of the innovative technologies,which were developed by Mitsubishi-Hitachi Metals Machinery,Inc.(hereinafter referred to as M-H),including the evolution of the pair cross mill,mill stabilizing device,on-line roll profiler,shape meter for hot-rolling,endless hot-rolling, recent application of UCM,and M-H split housing type 20-high mill.
基金Ferdowsi Universityof Mashhad,Iran for providing the laboratory facilitiesand financial support(Grant No.15226)
文摘The effects of moisture content （8%, 10%and 12%）, variety （Tarom and Fajr） and parboiling on milling quality of rice as a function of milling recovery （MR）, head rice yield （HRY）, degree of milling （DOM） and whiteness were investigated. The parboiled grains was prepared with three soaking temperatures of 25 oC, 50 oC and 75 oC and three steaming times of 10, 15 and 20 min. As a result of parboiling, the increasing rates of MR and HRY values were 7.8%and 14.3%for Tarom and 9.8%and 10.0%for Fajr, respectively, and the decreasing rates for DOM and whiteness were 6.6%and 10.8%for Tarom and 6.8% and 10.5% for Fajr, respectively. Moreover, decreasing moisture content to 8%maximized MR （75.8% for Tarom and 74.3% for Fajr） and HRY （65.8% for Tarom and 57.0% for Fajr） while increasing that to 12%revealed maximum values of DOM （6.1%for Tarom and 6.2%for Fajr） and whiteness （24.8%for Tarom and 28.2%for Fajr）.
文摘In this paper, the milling parameters of high energy ball mill (Fritsch Pulverisette 7) like vial geometry, number and size of balls and speed of the mill were modelled and discussed. Simulations through discrete element method (DEM) provide correlation between the milling parameters. A mathematical model is used to improve and develop this process. The results show that the loss of powder mass can remarkably improve the performance of milling. The balls made of stainless-steel have a positive effect on the milling efficiency. The simulation shows that the high ball milling velocities can contribute to faster particle size reduction.
文摘Grinding (Particle size reduction) of biomass is an age-long operation that is performed during the preparation process of certain food products. Among the grinding mill machines mostly used for this operation are hammer mill and disk mill. Being that the nature of biomass affects the performance and choice of grinding-mill machine to be adopted, it is imperative to compare and select appropriate grinding mill machine that is efficient and effective. In this paper, a comparative technique to evaluate and select appropriate grinding mill machine for particle size reduction of dried white yam (Dioscorea rotundata) is proposed. Hammer mill and disk mill machines were selected for consideration. Two white yam species (Benue and Delta Yam) were prepared into dried chips and ground using the selected mills. Among the attribute (performance parameters) considered are crushing time, particle size distribution and energy consumed. A measure of performance (Index I) based on the comparative technique was formulated and used in evaluating the performance of the two mills. In the hammer mill, index I recorded 2721.2 and 3719.82 par/kWh for Benue Yam chips at screen size 4 and 6 mm, respectively, while 2647.89 and 3472.01 par/kWh was recorded for Delta yam chips at screen size 4 and 6 mm, respectively. Index I values for the Disk mill were 2536.25 and 2433.42 par/kWh at 1.2 mm clearance distance for Benue Yam chips and Delta Yam chips, respectively. The results indicated that hammer mill performed better overall than the disk mill. The comparative technique was found suitable in the evaluation of the performance of the mills. It is recommended that hammer mill be adopted.
