The preparation of γ-Fe<sub>2</sub>O<sub>3</sub>/Gd<sub>2</sub>O<sub>3</sub> nanocomposite for possible use in magnetic hyperthermia application was done by ball millin...The preparation of γ-Fe<sub>2</sub>O<sub>3</sub>/Gd<sub>2</sub>O<sub>3</sub> nanocomposite for possible use in magnetic hyperthermia application was done by ball milling technique. The nanocomposite was characterized by X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). The heating efficiency and the effect of milling time (5 h and 30 h) on the structural and magnetic properties of the nanocomposite were reported. XRD analysis confirms the formation of the nanocomposite, while magnetization measurements show that the milled sample present hysteresis with low coercivity and remanence. The specific absorption rate (SAR) under an alternating magnetic field is investigated as a function of the milling time. A mean heating efficiency of 68 W/g and 28.7 W/g are obtained for 5 h and 30 h milling times respectively at 332 kHz and 170 Oe. The results showed that the obtained nanocomposite for 5 h milling time is a promising candidate for magnetic hyperthermia due to his properties which show an interesting magnetic behavior and high specific absorption rate.展开更多
Introduction: Noise is the second leading cause of hearing loss in adults after presbycusis. The objective of this work was to study hearing loss induced by the noise of mills in the markets of Parakou. Methods: This ...Introduction: Noise is the second leading cause of hearing loss in adults after presbycusis. The objective of this work was to study hearing loss induced by the noise of mills in the markets of Parakou. Methods: This was a descriptive and analytical cross-sectional study, conducted from February 3 to June 3, 2021 in the markets of Parakou. It concerned millers and sellers located within a 5 meter radius around the mills and among whom pure-tone audiometry was performed to detect a hearing loss. Subjects with no particular medical health history, under 55 years of age and having been working in these markets since more than 12 months, were included. Results: In this study, 103 subjects were selected, including 43 millers and 61 sellers. Their average age was 29 ± 13 years. The sex ratio was 0.49. The average length of service in the profession was 8 years with the extremes of 3 months and 47 years. They were exposed to noise on average 10 hours per day and 6 days a week. The average duration of weekly noise exposure was 23 h 28 min ± 13 h 32 min with the extremes of 5 h 00 min and 52 h 30 min. The average level of noise exposure was 90 dB with the extremes of 72 and 110 dB. 24 subjects reported symptoms related to noise such as headache, tinnitus, and hearing loss, with respective proportions of 22.33%, 20.39% and 06.80%. The prevalence of noise-related hearing loss was 26.21% (n = 27/103). Subjects with a notch at 4000 Hz and normal Average Hearing Loss (AHL) (20.39%) had a seven-time greater risk of developing noise-induced hearing loss (OR = 6.58;95% CI [2.54 - 18.8], p Conclusion: Hearing loss related to the noise of mills affected both millers and sellers near the mills in markets, hence the importance of regulating mills.展开更多
In this paper, the instantaneous undeformed chip thickness is modeled to include the dynamic modulation caused by the tool vibration while the dynamic regenerative effects are taken into account. The numerical method ...In this paper, the instantaneous undeformed chip thickness is modeled to include the dynamic modulation caused by the tool vibration while the dynamic regenerative effects are taken into account. The numerical method is used to solve the differential equations goveming the dynamics of the milling system. Several chatter detection criteria are applied synthetically to the simulated signals and the stability diagram is obtained in time-domain. The simulation results in time-domain show a good agreement with the analytical prediction, which is validated by the cutting experiments. By simulating the chatter stability lobes in the time-domain and analyzing the influences of different spindle speeds on the vibration amplitudes of the tool under a Fixed chip-load condition, conclusions could be drawn as follows： In rough milling, higher machining efficiency can be achieved by selecting a spindle speed corresponding to the axial depth of cut in accordance with the simulated chatter stability lobes, and in Fmish milling, lower surface roughness can be achieved by selecting a spindle speed well beyond the resonant frequency of machining system.展开更多
文摘The preparation of γ-Fe<sub>2</sub>O<sub>3</sub>/Gd<sub>2</sub>O<sub>3</sub> nanocomposite for possible use in magnetic hyperthermia application was done by ball milling technique. The nanocomposite was characterized by X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). The heating efficiency and the effect of milling time (5 h and 30 h) on the structural and magnetic properties of the nanocomposite were reported. XRD analysis confirms the formation of the nanocomposite, while magnetization measurements show that the milled sample present hysteresis with low coercivity and remanence. The specific absorption rate (SAR) under an alternating magnetic field is investigated as a function of the milling time. A mean heating efficiency of 68 W/g and 28.7 W/g are obtained for 5 h and 30 h milling times respectively at 332 kHz and 170 Oe. The results showed that the obtained nanocomposite for 5 h milling time is a promising candidate for magnetic hyperthermia due to his properties which show an interesting magnetic behavior and high specific absorption rate.
文摘Introduction: Noise is the second leading cause of hearing loss in adults after presbycusis. The objective of this work was to study hearing loss induced by the noise of mills in the markets of Parakou. Methods: This was a descriptive and analytical cross-sectional study, conducted from February 3 to June 3, 2021 in the markets of Parakou. It concerned millers and sellers located within a 5 meter radius around the mills and among whom pure-tone audiometry was performed to detect a hearing loss. Subjects with no particular medical health history, under 55 years of age and having been working in these markets since more than 12 months, were included. Results: In this study, 103 subjects were selected, including 43 millers and 61 sellers. Their average age was 29 ± 13 years. The sex ratio was 0.49. The average length of service in the profession was 8 years with the extremes of 3 months and 47 years. They were exposed to noise on average 10 hours per day and 6 days a week. The average duration of weekly noise exposure was 23 h 28 min ± 13 h 32 min with the extremes of 5 h 00 min and 52 h 30 min. The average level of noise exposure was 90 dB with the extremes of 72 and 110 dB. 24 subjects reported symptoms related to noise such as headache, tinnitus, and hearing loss, with respective proportions of 22.33%, 20.39% and 06.80%. The prevalence of noise-related hearing loss was 26.21% (n = 27/103). Subjects with a notch at 4000 Hz and normal Average Hearing Loss (AHL) (20.39%) had a seven-time greater risk of developing noise-induced hearing loss (OR = 6.58;95% CI [2.54 - 18.8], p Conclusion: Hearing loss related to the noise of mills affected both millers and sellers near the mills in markets, hence the importance of regulating mills.
基金National Key Technologies R&D Program (2006BA103A16)Fundamental Research Project of COSTIND (K1203020507, B2120061326)
文摘In this paper, the instantaneous undeformed chip thickness is modeled to include the dynamic modulation caused by the tool vibration while the dynamic regenerative effects are taken into account. The numerical method is used to solve the differential equations goveming the dynamics of the milling system. Several chatter detection criteria are applied synthetically to the simulated signals and the stability diagram is obtained in time-domain. The simulation results in time-domain show a good agreement with the analytical prediction, which is validated by the cutting experiments. By simulating the chatter stability lobes in the time-domain and analyzing the influences of different spindle speeds on the vibration amplitudes of the tool under a Fixed chip-load condition, conclusions could be drawn as follows： In rough milling, higher machining efficiency can be achieved by selecting a spindle speed corresponding to the axial depth of cut in accordance with the simulated chatter stability lobes, and in Fmish milling, lower surface roughness can be achieved by selecting a spindle speed well beyond the resonant frequency of machining system.
