Relation between Modulus of Elasticity and Compressive Strength of Ultrahigh-Strength Mortar with Mixed Silicon Carbide as Fine Aggregate

Ultrahigh-strength mortar mixed surface-oxidized silicon carbide as a fine aggregate was prepared by means of press-casting followed by curing in an autoclave. The relation between modulus of elssticity up to 111 GPa and compressive strength up to 360 MPa of mortar mixed silicon carbide was discussed and it was revealed that the contributions of the aggregate hardness and of the interfacial strength between the aggregate and the cement paste on the elasticity of mortar were imporant.

Numerical simulations of compressible mixing layers with a discontinuous Galerkin method

Discontinuous Galerkin（DG） method is known to have several advantages for flow simulations,in particular,in fiexible accuracy management and adaptability to mesh refinement. In the present work,the DG method is developed for numerical simulations of both temporally and spatially developing mixing layers. For the temporally developing mixing layer,both the instantaneous fiow field and time evolution of momentum thickness agree very well with the previous results. Shocklets are observed at higher convective Mach numbers and the vortex paring manner is changed for high compressibility. For the spatially developing mixing layer,large-scale coherent structures and self-similar behavior for mean profiles are investigated. The instantaneous fiow field for a three-dimensional compressible mixing layer is also reported,which shows the development of largescale coherent structures in the streamwise direction. All numerical results suggest that the DG method is effective in performing accurate numerical simulations for compressible shear fiows.

A Simple Mix Proportion Design Method Based on Frost Durability for Recycled High Performance Concrete Using Fully Coarse Recycled Aggregate

Durability design of recycled high performance concrete（RHPC） is fundamental for improving the use rate and level of concrete waste as coarse recycled aggregate（CRA）. We discussed a frostdurability-based mix proportion design method for RHPC using 100 % CRA and natural sand. Five groups of RHPC mixes with five strength grades（40, 50, 60, 70 and 80 MPa） were produced using CRA with four quality classes, and their workability, 28 d compressive strengths and frost resistances（measured by the compressive strength loss ratio and the relative dynamic modulus of elasticity） were tested. Relationships between the 28 d compressive strength, the frost resistance and the CRA quality characteristic parameter, water absorption, were then developed. The criterion of a CRA maximum water absorption limit value for RHPC was suggested, independent of its source and quality class. The results show that all RHPC mixes achieve the expected target workability, strength, and frost durability. The research results demonstrate that the application of the proposed method does not require trial testing prior to use.

Modelling of pressure-strain correlation in compressible turbulent flow

Previous studies carried out in the early 1990s conjectured that the main compressible effects could be associated with the dilatational effects of velocity fluctuation. Later, it was shown that the main compressibility effect came from the reduced pressure-strain term due to reduced pressure fluctuations. Although better understanding of the compressible turbulence is generally achieved with the increased DNS and experimental research effort, there are still some discrepancies among these recent findings. Analysis of the DNS and experimental data suggests that some of the discrepancies are apparent if the compressible effect is related to the turbulent Mach number, Mt. From the comparison of two classes of compressible flow, homogenous shear flow and inhomogeneous shear flow （mixing layer）, we found that the effect of compressibility on both classes of shear flow can be characterized in three categories corresponding to three regions of turbulent Mach numbers： the low-Mr, the moderate-Mr and high-Mr regions. In these three regions the effect of compressibility on the growth rate of the turbulent mixing layer thickness is rather different. A simple approach to the reduced pressure-strain effect may not necessarily reduce the mixing-layer growth rate, and may even cause an increase in the growth rate. The present work develops a new second-moment model for the compressible turbulence through the introduction of some blending functions of Mt to account for the compressibility effects on the flow. The model has been successfully applied to the compressible mixing layers.

Mechanical Properties and ITZ Microstructure of Recycled Aggregate Concrete Using Carbonated Recycled Coarse Aggregate

The effect of carbonation treatment and mixing method on the mechanical properties and interfacial transition zone（ITZ） properties of recycled aggregate concrete（RAC） was investigated. Properties of recycled concrete aggregate（RCA） were tested firstly. Then, five types of concretes were made and slump of fresh concrete was measured immediately after mixing. Compressive strength and splitting tensile strength of hardened concrete were measured at 28 d. Meanwhile, the microstructure of RAC was analyzed by backscattered electron（BSE） image. It was found that the water absorption ratio of carbonated recycled concrete aggregate（CRCA） was much lower when compared to the untreated RCA. Comparatively, the apparent density of CRCA was not significantly modified. The concrete strength results indicate that the mix CRAC-2 prepared with CRCA by adopting two-stage mixing approach shows the highest compressive strength value compared to the other mixes. The microstructural analysis demonstrate that the mix CRAC-2 has a much denser old ITZ than the untreated RAC because of the chemical reaction between CO2 and the hydration products of RCA. This study confirms that the ITZ microstructure of RAC can be efficiently modified by carbonation treatment of RCA and encourages broadening the application of construction and demolition wastes.

Effects of Silica Aerogel Content on Microstructural and Mechanical Properties of Poly(methyl methacrylate)/Silica Aerogel Dual-scale Cellular Foams Processed in Supercritical Carbon Dioxide

A novel poly（methyl-methacrylate）/silica aerogel（PMMA/SA） dual-scale cellular foam was synthesized with internal mixing followed by the supercritical carbon dioxide foaming process.The effects of silica aerogel content on the microstructural and mechanical performance of the foams were investigated by SEM,TEM analysis,and mechanical tests.The experimental results suggest that the employment of silica aerogel granule as addictive can distinctly improve the morphological feature as well as the mechanical performance in comparison to neat PMMA foam by uniformizing cell size distribution,decreasing cell size and increasing cell density.And dual-scale cells including micrometric cells of 3-10 μm and nanometric cells of about 50 nm existed in the structure of foams resulting from the retained original framework structure of silica aerogel,which has not been described in other studies with the addition of various fillers.Furthermore,the mechanical strength was significantly elevated even with a small amount of silica aerogel resulting from the unique microstructure,decreased cell size and enhanced cell walls.The compressive strength was 18.12 MPa and the flexural strength was 18.90 MPa by adding 5wt% and 2wt% silica aerogel,respectively.These results demonstrate the potential to synthesize PMMA/SA dual-scale cellular foams to be used as structural materials with the advantages of low density and high strength.

Wavy structures in compressible mixing layers

Semi-periodic structures namely inclined wavy structures （IWS） are experimentally observed in compressible mixing layers at two convective Mach numbers （Mc = 0.11 and 0.47）. Flow structures are visualized by the laserinduced planar laser Mie scattering （PLMS） technique. Two methods are developed to investigate the spatial distribu- tion and geometry of IWS： （1） the dominant mode extrac- tion （DME） method, to extract the dominant modes of IWS from the streamwise gray-level fluctuation, and （2） the phase tracking （PT） method, to identify the shape of IWS. The re- sults suggest that pressure perturbations account for the for- marion of IWS in the initial mixing region and the joint effect of dilatation and coherent vortices enhances IWS in the well- developed region. The large transverse （cross-flow） scale of the IWS and their relation to coherent vortices （CV） indicate that the disturbance originated from CV in the mixing center propagates far into the free streams. The DME and the PT method are shown to be the effective tools to study the geometrical features of wavy structures in compressible shear flows.

Vortex structure simulation for supersonic mixing layers using nonlinear PSE method

The method of nonlinear parabolized stability equations（PSE） is applied in the simulation of vortex structures in compressible mixing layer.The spatially-evolving unstable waves,which dominate the vortex structure,are investigated through spatial marching method.The instantaneous flow field is obtained by adding the harmonic waves to basic flow.The results show that T-S waves do not keep growing exponentially as the linear evolution,the energy transfer to high order harmonic modes,and that finally all harmonic modes get saturated due to nonlinear interaction.The mean flow distortion induced by the nonlinear interaction between the harmonic modes and their conjugate harmonic ones,makes great change of the average flow and increases the thickness of mixing layer. PSE methods can well capture the two- and three-dimensional large scale nonlinear vortex structures in mixing layers such as vortex roll-up,vortex pairing,and A vortex.

A compressed variance component mixed model for detecting QTNs and QTN-by-environment and QTN-by-QTN interactions in genome-wide association studies

Although genome-wide association studies are widely used to mine genes for quantitative traits,the effects to be estimated are confounded,and the methodologies for detecting interactions are imperfect.To address these issues,the mixed model proposed here first estimates the genotypic effects for AA,Aa,and aa,and the genotypic polygenic background replaces additive and dominance polygenic backgrounds.Then,the estimated genotypic effects are partitioned into additive and dominance effects using a one-way analysis of variance model.This strategy was further expanded to cover QTN-by-environment interactions(QEIs)and QTN-by-QTN interactions(QQIs)using the same mixed-model framework.Thus,a three-variance-component mixed model was integrated with our multi-locus random-SNP-effect mixed linear model(mrMLM)method to establish a new methodological framework,3VmrMLM,that detects all types of loci and estimates their effects.In Monte Carlo studies,3VmrMLM correctly detected all types of loci and almost unbiasedly estimated their effects,with high powers and accuracies and a low false positive rate.In re-analyses of 10 traits in 1439 rice hybrids,detection of 269 known genes,45 known gene-by-environment interactions,and 20 known gene-by-gene interactions strongly validated 3VmrMLM.Further analyses of known genes showed more small(67.49%),minor-allele-frequency(35.52%),and pleiotropic(30.54%)genes,with higher repeatability across datasets(54.36%)and more dominance loci.In addition,a heteroscedasticity mixed model in multiple environments and dimension reduction methods in quite a number of environments were developed to detect QEIs,and variable selection under a polygenic background was proposed for QQI detection.This study provides a new approach for revealing the genetic architecture of quantitative traits.

Optimization Study of a Coanda Ejector

The Coanda effect has long been employed in the aerospace applications to improve the performances of various devices. This effect is the ability of a flow to follow a curved contour without separation and has well been utilized in ejectors where a high speed jet of fluid emerges from a nozzle in the ejector body, follows a curved surface and drags the secondary flow into the ejector. In Coanda ejectors, the secondary flow is dragged in the ejector due to the primary flow momentum. The transfer of momentum from the primary flow to the secondary flow takes place through turbulent mixing and viscous effects. The secondary flow is then dragged by turbulent shear force of the ejector while being mixed with the primary flow by the persistence of a large turbulent intensity throughout the ejector. The performance of a Coanda ejector is studied mainly based on how well it drags the secondary flow and the amount of mixing between the two flows at the ejector exit. The aim of the present study is to investigate the influence of various geometric parameters and pressure ratios on the Coanda ejector performance. The effect of various factors, such as, the pressure ratio, primary nozzle and ejector configurations on the system performance has been evaluated based on a performance parameter defined elsewhere. The performance of the Coanda ejector strongly depends on the primary nozzle configuration and the pressure ratio. The mixing layer growth plays a major role in optimizing the performance of the Coanda ejector as it decides the ratio of secondary mass flow rate to primary mass flow rate and the mixing length.

Experimental evidence for non-linear growth in compressible mixing layer

An experimental study of compressible mixing layers(CMLs)was conducted using planar laser Mie scattering(PLMS)visualizations from condensed ethanol droplets in the flow.Large ensembles of digital images were collected for two flow conditions at convective Mach numbers Mc=0.11 and 0.47.The coherent vortices,braids and eruptions in the mixing zone were observed,interpreted as evidence of multi-scale,three-dimensional structures at a high Reynolds number.The mixing layers with a large visualized range present two stages along the streamwise direction,corresponding to the initial mixing and the well-developed stage.A new method,the gray level ensemble average method(GLEAM),by virtue of the similarity of the mixing layer,was applied to measure the growth rate of the CML thickness.New evidence for a nonlinear growth of CML is reported,providing an interpretation of previous observations of the scattering of the growth rate.

Genome-wide association study of the backfat thickness trait in two pig populations

Backfat thickness is a good predictor of carcass lean content,an economically important trait,and a main breeding target in pig improvement.In this study,the candidate genes and genomic regions associated with the tenth rib backfat thickness trait were identified in two independent pig populations,using a genome-wide association study of porcine 60K SNP genotype data applying the compressed mixed linear model(CMLM)statistical method.For each population,30 most significant single-nucleotide polymorphisms(SNPs)were selected and SNP annotation implemented using Sus scrofa Build 10.2.In the first population,25 significant SNPs were distributed on seven chromosomes,and SNPs on SSC1 and SSC7 showed great significance for fat deposition.The most significant SNP(ALGA0006623)was located on SSC1,upstream of the MC4R gene.In the second population,27 significant SNPs were recognized by annotation,and 12 SNPs on SSC12 were related to fat deposition.Two haplotype blocks,M1GA0016251-MARC0075799 and ALGA0065251-MARC0014203-M1GA0016298-ALGA0065308,were detected in significant regions where the PIPNC1 and GH1 genes were identified as contributing to fat metabolism.The results indicated that genetic mechanism regulating backfat thickness is complex,and that genome-wide associations can be affected by populations with different genetic backgrounds.