Facile preparation and efficient MnxCoy porous nanosheets for the sustainable catalytic process of soot

The pursuit of high-performance is worth considerable effort in catalysis for energy efficiency and environmental sustainability. To develop redox catalysts with superior performance for soot combustion, a series of Mn_(x)Co_(y) oxides were synthesized using MgO template substitution.This method greatly improves the preparation and catalytic efficiency and is more in line with the current theme of green catalysts and sustainable development. The resulting Mn_(1)Co_(2.3) has a strong activation capability of gaseous oxygen due to a high concentration of Co^(3+) and Mn^(3+). The Mn doping enhanced the intrinsic activity by prompting oxygen vacancy formation and gaseous oxygen adsorption. The nanosheet morphology with abundant mesoporous significantly increased the solid–solid contact efficiency and improved the adsorption capability of gaseous reactants. The novel design of Mn_(1)Co_(2.3)oxide enhanced its catalytic performance through a synergistic effect of Mn doping and the porous nanosheet morphology, showing significant potential for the preparation of high-performance soot combustion catalysts.

Innovative Mn_(3-x)O_(4-y)@NCA design:Leveraging Mn/O vacancies and amorphous architecture for enhanced sodium-ion storage

Manganese-based oxide electrode materials suffer from severe Jahn-Teller(J-T)distortion,leading to severe cycle instability in sodium ion storage.However,it is difficult to adjust the electron at d orbitals exactly to a low spin state to eliminate orbital degeneracy and suppress J-T distortion fundamentally.This article constructed concentration-controllable Mn/O coupled vacancy and amorphous network in Mn_(3)O_(4) and coated it with nitrogen-doped carbon aerogel(Mn_(3-x)O_(4-y)@NCA).The existence of Mn/O vacancies has been confirmed by scanning transmission electron microscopy(STEM)and positron annihilation lifetime spectroscopy(PALS).Atomic absorption spectroscopy(AAS)and X-ray photoelectron spectroscopy(XPS)determine the most optimal ratio of Mn/O vacancies for sodium ion storage is 1:2.Density functional theory(DFT)calculations prove that Mn/O coupled vacancies with the ratio of 1:2could exactly induce a low spin states and a d~4 electron configuration of Mn,suppressing the J-T distortion successfully.The abundant amorphous regions can shorten the transport distance of sodium ions,increase the electrochemically active sites and improve the pseudocapacitance response.From the synergetic effect of Mn/O coupled vacancies and amorphous regions,Mn_(3-x)O_(4-y)@NCA exhibits an energy density of 37.5 W h kg^(-1)and an ultra-high power density of 563 W kg^(-1)in an asymmetric supercapacitor.In sodium-ion batteries,it demonstrates high reversible capacity and exceptional cycling stability.This research presents a new method to improve the Na^(+)storage performance in manganese-based oxide,which is expected to be generalized to other structural distortion.

Crack elimination and strength enhancement mechanisms of selective laser melted Si-modified Al−Mn−Mg−Er−Zr alloy

In order to increase the processability and process window of the selective laser melting(SLM)-fabricated Al−Mn−Mg−Er−Zr alloy,a novel Si-modified Al−Mn−Mg−Er−Zr alloy was designed.The effect of Si alloying on the surface quality,processability,microstructure,and mechanical properties of the SLM-fabricated alloy was studied.The results showed that introducing Si into the Al−Mn−Mg−Er−Zr alloy prevented balling and keyhole formation,refined the grain size,and reduced the solidification temperature,which eliminated cracks and increased the processability and process window of the alloy.The maximum relative density of the SLM-fabricated Si/Al−Mn−Mg−Er−Zr alloy reached 99.6%.The yield strength and ultimate tensile strength of the alloy were(371±7)MPa and(518±6)MPa,respectively.These values were higher than those of the SLM-fabricated Al−Mn−Mg−Er−Zr and other Sc-free Al−Mg-based alloys.

Hardening mechanism and thermal-solid coupling model of laminar plasma surface hardening of 65 Mn steel

In the present work,the laminar plasma surface hardening method is employed to enhance the service life of metal components fabricated from 65 Mn steel.The mechanical and wear behaviors of the laminar plasma surface hardened 65 Mn steel were analyzed.The martensite transition transformation of the temperature of the laminar plasma-hardened 65 ferrite Mn steel was determined by a thermal-solid coupling model.Based on the orthogonal experimental results,the optimal hardening parameters were confirmed.The scanning velocity,quenching distance and arc current are 130 mm/min,50 mm and 120 A,respectively.The pearlites and ferrites are transformed into martensites in the hardened zone,while the ratio of martensite in the heataffected zone decreases with the increase in the hardening depth.Compared to the untreated 65Mn steel,the average hardness increases from 220 HV_(0.2)to 920 HV_(0.2)in the hardened zone and the corresponding absorbed power increases from 118.7 J to 175.5 J.At the same time,the average coefficient of friction(COF)decreases from 0.763 to 0.546,and the wear rate decreases from 5.39×10^(-6)mm^(3)/(N·m)to 2.95×10^(-6)mm^(3)/(N·m),indicating that the wear resistance of 65Mn steel could be significantly improved by using laminar surface hardening.With the same hardening parameters,the depth and width of the hardened zone predicted by the thermal-solid coupling model are 1.85 mm and 11.20 mm,respectively,which are in accordance with the experimental results;depth is 1.83 mm and width is 11.15 mm.In addition,the predicted hardness distributions of the simulation model are in accordance with the experimental results.These results indicate that the simulation model could effectively predict the microstructure characteristics of 65 Mn steel.

Engineering single-atom Mn on nitrogen-doped carbon to regulate lithium-peroxide reaction kinetics for rechargeable lithium-oxygen batteries

Precision engineering of catalytic sites to guide more favorable pathways for Li_(2)O_(2) nucleation and decom-position represents an enticing kinetic strategy for mitigating overpotential,enhancing discharge capac-ity,and improving recycling stability of Li-O_(2) batteries.In this work,we employ metal-organic frameworks(MOFs)derivation and ion substitution strategies to construct atomically dispersed Mn-N_(4) moieties on hierarchical porous nitrogen-doped carbon(Mn SAs-NC)with the aim of reducing the over-potential and improving the cycling stability of Li-O_(2) batteries.The porous structure provides more chan-nels for mass transfer and exposes more highly active sites for electrocatalytic reactions,thus promoting the formation and decomposition of Li_(2)O_(2).The Li-O_(2) batteries with Mn SAs-NC cathode achieve lower overpotential,higher specific capacity(14290 mA h g^(-1) at 100 mAg^(-1)),and superior cycle stability(>100 cycles at 200 mA g^(-1))compared with the Mn NPs-NC and NC.Density functional theory(DFT)cal-culations reveal that the construction of Mn-N_(4) moiety tunes the charge distribution of the pyridinic N-rich vacancy and balances the affinity of the intermediates(LiO_(2) and Li_(2)O_(2)).The initial nucleation of Li_(2)O_(2) on Mn SAs-NC favors the O_(2)-→LiO_(2)→Li_(2)O_(2) surface-adsorption pathway,which mitigates the overpoten-tials of the oxygen reduction(ORR)and oxygen evolution reaction(OER).As a result,Mn SAs-NC with Mn-N_(4) moiety effectively facilitates the Li_(2)O_(2) nucleation and enables its reversible decomposition.This work establishes a methodology for constructing carbon-based electrocatalysts with high activity and selectivity for Li-O_(2)batteries.

Construction of MnS/MoS_(2) heterostructure on two-dimensional MoS_(2) surface to regulate the reaction pathways for high-performance Li-O_(2) batteries

The inherent catalytic anisotropy of two-dimensional(2D) materials has limited the enhancement of LiO_(2) batteries(LOBs) performance due to the significantly different adsorption energies on 2D and edge surfaces.Tuning the adsorption strength in 2D materials to the reaction intermediates is essential for achieving high-performance LOBs.Herein,a MnS/MoS_(2) heterostructure is designed as a cathode catalyst by adjusting the adsorption behavior at the surface.Different from the toroidal-like discharge products on the MoS_(2) cathode,the MnS/MoS_(2) surface displays an improved adsorption energy to reaction species,thereby promoting the growth of the film-like discharge products.MnS can disturb the layer growth of MoS_(2),in which the stack edge plane features a strong interaction with the intermediates and limits the growth of the discharge products.Experimental and theoretical results confirm that the MnS/MoS_(2) heterostructure possesses improved electron transfer kinetics at the interface and plays an important role in the adsorption process for reaction species,which finally affects the morphology of Li_2O_(2),In consequence,the MnS/MoS_(2) heterostructure exhibits a high specific capacity of 11696.0 mA h g^(-1) and good cycle stability over 1800 h with a fixed specific capacity of 600 mA h g^(-1) at current density of100 mA g^(-1) This work provides a novel interfacial engineering strategy to enhance the performance of LOBs by tuning the adsorption properties of 2D materials.

The Al_(2)O_(3)and Mn/Al_(2)O_(3)sorbents highly utilized in destructive sorption of NF_(3)

NF_(3)is commonly used as an etching and cleaning gas in semiconductor industry,however it is a strongly greenhouse gas.Therefore,the destruction of disposal NF_(3)is an urgent task to migrate the greenhouse effect.Among the technologies for NF_(3)abatement,the destructive sorption of NF_(3)over metal oxides sorbents is an effective way.Thus,the search for a highly reactive and utilized sorbent for NF_(3)destruction is in great demand.In this work,AlOOH supported on carbon-sphere(AlOOH/CS)as precursors were synthesized hydrothermally and heat-treated to prepare the Al_(2)O_(3)sorbents.The influence of AlOOH/CS hydrothermal temperatures on the reactivity of derived Al_(2)O_(3)sorbents for NF_(3)destruction was investigated,and it is shown that the Al2O3 from AlOOH/CS hydro-thermalized at 120℃is superior to others.Subsequently,the optimized Al_(2)O_(3)was covered by Mn(OH)x to prepare Mn/Al_(2)O_(3)sorbents via changing hydrothermal temperatures and Mn loadings.The results show that the Mn/Al_(2)O_(3)sorbents are more utilized than bare Al_(2)O_(3)in NF_(3)destructive sorption due to the promotional effect of Mn_(2)O_(3)as surface layer on the fluorination of Al_(2)O_(3)as substrate,especially the optimal 5%Mn/Al2O3(160℃)exhibits a utilization percentage as high as 90.4%,and remarkably exceeds all the sorbents reported so far.These findings are beneficial to develop more efficient sorbents for the destruction of NF_(3).

Effect of Mn and Mo on microstructure and mechanical properties of Al-Si-Cu-Mg-0.6Fe alloy

Effect of different Mn and Mo contents on microstructure and mechanical properties of Al-Si-Cu-Mg-0.6Fe alloy was studied.Results indicate that the increase of Mo and decrease of Mn lead to a decrease in the size of theα-Al_(15)(FeMnMo)_(3)Si_(2) phase formed during solidification.Theα-Al_(15)(FeMnMo)_(3)Si_(2) phase reaches a minimum value of about 16.3μm at 0.2wt.%Mo and 0.1wt.%Mn addition.After solution treatment,theα-Al(FeMnMo)Si dispersed phase is precipitated.When only Mn is added,theα-Al(FeMnMo)Si dispersed phase mainly distributes near the grain boundaries,while when only Mo is added,it primarily distributes in the central region of the matrix.When both Mn and Mo are added,the dispersed phase has a larger and denser dispersed region and is uniformly distributed near the Al matrix and grain boundaries.Moreover,the best overall mechanical properties of the alloy are obtained with the combined addition of 0.1wt.%Mn and 0.2wt.%Mo,due to the smaller size ofα-Al_(15)(FeMnMo)_(3)Si_(2) phase and the larger area fraction and higher density of theα-Al(FeMnMo)Si dispersed phase.The yield strength,ultimate tensile strength,and elongation are respectively improved 67.7 MPa,48.5 MPa and 5.3%,respectively,compared to that of the alloy with only 0.3wt.%Mn.

Effects of Ce addition on microstructure and mechanical properties of Mg-6Zn-1Mn alloy

The effects of Ce addition on the microstructure of Mg-6Zn-1Mn alloy during casting, homogenization, hot extrusion, T4, T6 and T4＋two-step aging were investigated. The mechanical properties of alloys with and without Ce were compared. The results showed that Ce had an obvious effect on the microstructure of ZM61-0.5Ce alloy by restricting the occurrence of dynamic recrystallization and restraining the grain growth during extrusion and heat treatment subsequently. A new binary phase Mg 12 Ce was identified in ZM61-0.5Ce alloy, which distributed at grain boundaries and was broken to small particles distributed at grain boundaries along extrusion direction during extrusion. The mechanical properties of as-extruded ZM61-0.5Ce alloy were improved with the addition of Ce. The improved tensile properties of as-extruded ZM61-0.5Ce alloy were due to the finer grain sizes as compared to ZM61 alloy. However, the UTS and YS decreased severely and the elongation increased when ZM61-0.5Ce was treated by T6 and T4＋two-step aging. Brittle Mg 12 Ce phase, which was distributed at the grain boundary areas and cannot dissolve into the Mg matrix after solution treatment, became crack source under tensile stress.

Effect of sintering temperature on cycling performance and rate performance of LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2

LiNi0.8Co0.1Mn0.1O2 powder was prepared by mixing LiOH·H2O and co-precipitated Ni0.8Co0.1Mn0.1（OH）2 at a molar ratio of 1：1.05, followed by sintering at different temperatures. The effects of temperature on the morphology, structure and electrochemical performance were extensively studied. SEM and XRD results demonstrate that the sintering temperature has large influence on the morphology and structure and suitable temperature is very important to obtain spherical materials and suppresses the ionic distribution. The charge-discharge tests show that the electrochemical performance of LiNi0.8Co0.1Mn0.1O2 powders becomes better with the increase of temperature from 700 ℃ to 750 ℃ and higher temperature will deteriorate the performance. Although both of materials obtained at 750 ℃ and 780 ℃ demonstrate almost identical cyclic stability at 2C rate, which delivers 71.9%retention after 200 cycles, the rate performance of powder calcined at 780 ℃ is much poorer than that at 750 ℃. The XRD results demonstrate that the poor performance is ascribed to more severe ionic distribution caused by higher temperature.

Influence of pretreatment process on structure, morphology and electrochemical properties of Li[Ni_(1/3)Co_(1/3)Mn_(1/3)]O_2 cathode material

The layered Li[Ni1/3Mn1/3Co1/3]O2 was separately synthesized by pretreatment process of ball mill method and solution phase route, using [Ni1/3Co1/3Mn1/3]3O4 and lithium hydroxide as raw materials. The physical and electrochemical behaviors of Li[Ni1/3Mn1/3Co1/3]O2 were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, field emission scanning electron microscopy （FESEM） and electrochemical charge/discharge cycling tests. The results show that the difference in pretreatment process results in the difference in compound Li[Ni1/3Co1/3Mn1/3]O2 structure, morphology and the electrochemical characteristics. The Li[Ni1/3Mn1/3Co1/3]O2 prepared by solution phase route maintains the uniform spherical morphology of the [Ni1/3Co1/3Mn1/3]3O4, and it exhibits a higher capacity retention and better rate capability than that prepared by ball mill method. The initial discharge capacity of this sample reaches 178 mA-h/g and the capacity retention after 50 cycles is 98.7% at a current density of 20 mA/g. Moreover, it delivers high discharge capacity of 135 mA-h/g at a current density of 1 000 mA/g.

Mn掺杂Zigzag(8,0)型单壁碳纳米管吸附甲醛分子的密度泛函理论研究

甲醛是一种对人体健康造成巨大威胁的污染物。气态甲醛浓度的准确检测对大气空气治理评估和室内环境安全均有重要意义,而高效传感器的研发则是甲醛分子检测技术优化的关键。本研究通过基于第一性原理的DFT计算软件VASP,对甲醛分子在Mn掺杂Zigzag(8,0)型单臂碳纳米管上的吸附特性进行研究。结果表明:Mn掺杂Zigzag(8,0)型单臂碳纳米管是一种稳定的分子构型。区别于在原始CNT上的物理吸附过程,甲醛分子在Mn掺杂CNT上的吸附键长更短,吸附能更大,属于化学吸附过程。同时,甲醛分子在Mn掺杂CNT上的吸附过程还伴随着明显的电荷转移。吸附过程发生后,吸附样品的光吸收曲线在580~705 nm以及365~447 nm的范围内出现明显的蓝移,在307~360 nm的范围内出现了明显的红移。

Mn微合金化Al-Si-Cu-Mg合金显微组织及耐蚀性能研究

Al-Si-Cu-Mg系列合金具有优异的强韧性,但其中的含Cu强化相极大地影响了该系合金的耐蚀性能。因此,本文通过对不同Mn含量的Al-7Si-2Cu-0.6Mg合金进行显微组织观察和电化学分析,探究Mn元素的添加对T6热处理状态下合金微观结构和耐蚀性的影响。结果表明,Mn添加量的提高对合金显微硬度几乎没有影响,但在合金基体中可以观察到弥散相。随着Mn含量升高,合金的耐蚀性呈现先升高后降低的趋势。添加0.360%Mn(质量分数)合金具有最佳耐蚀性,腐蚀电流密度比基础合金减少了54%。腐蚀形貌观察结果表明,Mn的添加可以显著减弱合金的点蚀趋势。

Mn18Cr18N加压冶炼的氮含量精准控制工艺分析与实验

高氮不锈钢中氮含量的精准控制是生产关键控制要素。以Mn18Cr18N高氮钢为研究对象,利用冶金学原理、Factsage热力学软件及热态实验与检测分析等方法,对加压感应熔炼过程钢种成分、温度及氮气压力与氮含量控制的关系进行研究。结果表明,基于理论数据的“成分-温度-压力”关系方程可信度高,3炉实验的氮气压力理论值、预测值与实际控制值吻合度良好。热态实验验证发现,Mn和Cr含量不变时,依靠提高氮分压可以提高钢锭中N含量,但是w[N]达到约1%时,通过提高氮分压增加氮含量的效果降低。Mn或Cr含量低时,可以通过提高氮分压达到提高氮含量的目的。降低钢中C和Si含量有利于钢中高氮含量的合金化及稳定控制。当需要控制Mn18Cr19N钢中的w[N]≥0.8%时,宜控制加压炉熔炼温度在1500~1550℃,氮气压力在0.225~0.325 MPa。

Mn/TiO_(2)低温SCR催化剂钾中毒机理研究

Mn/TiO_(2)具有良好的低温NH3选择性催化还原NOx(SCR)的活性。烟气中存在的碱金属会从物理和化学上毒害催化剂导致Mn/TiO_(2)催化剂中毒失活。论文以暴露{101}面TiO_(2)为载体制备Mn/TiO_(2)催化剂,采用浸渍法制备K中毒催化剂,研究了Mn/TiO_(2)低温SCR催化剂钾中毒机理。实验发现,Mn/TiO_(2)催化剂脱硝效率随K中毒浓度增加而减少;新鲜Mn/TiO_(2)催化剂表面NH3-SCR反应由E-R和L-H机理共同控制;K吸附会导致催化剂比表面积降低,催化剂表面Mn4+、化学吸附氧比例降低,表面酸性位点数量减少,导致脱硝活性降低;同时K更易吸附在Mn顶位以及桥接O位附近,导致NO的吸附活化受到严重遏制,同时削弱NH3的吸附,使得L-H机理受到阻断,只能以E-R机理控制为主。

60Si2Mn钢表面激光熔覆铁基涂层的组织及耐磨性研究

目的提高60Si2Mn钢的表面耐磨损性能。方法采用同步送粉方式在60Si2Mn钢表面进行激光熔覆X1、X22种铁基粉末。通过金相显微镜、场发射扫描电镜和X射线衍射仪,观察和分析熔覆层的显微组织、化学元素分布及相组成,采用显微硬度仪、多功能摩擦磨损试验机进行硬度、耐磨损性能测试。结果2种熔覆层均无裂纹、气孔等缺陷,涂层内部存在大量树枝晶、等轴晶和少量沿基材表面生长的平面晶,其中X1熔覆层的顶部区域等轴晶数量较多,组织更细小均匀。2种熔覆层均由相同物相(α-Fe)固溶体组成,未出现明显的其他物相的衍射峰。基体60Si2Mn钢平均硬度约为300HV,X1熔覆层的硬度为950~1000HV,平均硬度为975HV。X2熔覆层的硬度为784~821HV,平均硬度为803HV。经过球-盘磨损试验后,X1、X2熔覆层以及基体的体积磨损率分别为1.32×10^(-4)、1.94×10^(-4)、3.29×10^(-4)mm^(3)/(N·m)。结论2种熔覆层的硬度和耐磨损性能均优于基体,其中X1熔覆层的平均硬度比X2熔覆层的高约21%,其体积磨损率最小,耐磨损性能更好。

Influence of rare earth Ce on hot deformation behavior of as-cast Mn18Cr18N high nitrogen austenitic stainless steel

The hot deformation behavior of Mn18Cr18N and Mn18Cr18N+Ce high nitrogen austenitic stainless steels at 1173-1473 K and 0.01-1 s^(-1) were investigated by thermal compression tests.The influence mechanism of Ce on the hot deformation behavior was analyzed by Ce-containing inclusions and segregation of Ce.The results show that after the addition of Ce,large,angular,hard,and brittle inclusions(TiN-Al_(2)O_(3),TiN,and Al_(2)O_(3)) can be modified to fine and dispersed Ce-containing inclusions(Ce-Al-O-S and TiN-Ce-Al-O-S).During the solidification,Ce-containing inclusions can be used as heterogeneous nucleation particles to refine as-cast grains.During the hot deformation,Ce-containing inclusions can pin dislocation movement and grain boundary migration,induce dynamic recrystallization(DRX)nucleation,and avoid the formation and propagation of micro cracks and gaps.In addition,during the solidification,Ce atoms enrich at the front of solid-li-quid interface,resulting in composition supercooling and refining the secondary dendrites.Similarly,during the hot deformation,Ce atoms tend to segregate at the boundaries of DRX grains,inhibiting the growth of grains.Under the synergistic effect of Ce-containing inclusions and Ce segregation,although the hot deformation resistance and hot deformation activation energy are improved,DRX is more likely to occur and the size of DRX grains is significantly refined,and the problem of hot deformation cracking can be alleviated.Finally,the microhardness of the samples was measured.The results show that compared with as-cast samples,the microhardness of hot-deformed samples increases signific-antly,and with the increase of DRX degree,the microhardness decreases continuously.In addition,Ce can affect the microhardness of Mn18Cr18N steel by affecting as-cast and hot deformation microstructures.

First-principles calculations of Ni–(Co)–Mn–Cu–Ti all-d-metal Heusler alloy on martensitic transformation,mechanical and magnetic properties

The martensitic transformation,mechanical,and magnetic properties of the Ni_(2)Mn_(1.5-x)Cu_(x)Ti_(0.5) (x=0.125,0.25,0.375,0.5) and Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5)[(x=0.125,y=0.125,0.25,0.375,0.5) and (x=0.125,0.25,0.375,y=0.625)]alloys were systematically studied by the first-principles calculations.For the formation energy,the martensite is smaller than the austenite,the Ni–(Co)–Mn–Cu–Ti alloys studied in this work can undergo martensitic transformation.The austenite and non-modulated (NM) martensite always present antiferromagnetic state in the Ni_(2)Mn_(1.5-x)Cu_(x)Ti_(0.5) and Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5) (y<0.625) alloys.When y=0.625 in the Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5) series,the austenite presents ferromagnetic state while the NM martensite shows antiferromagnetic state.Cu doping can decrease the thermal hysteresis and anisotropy of the Ni–(Co)–Mn–Ti alloy.Increasing Mn and decreasing Ti content can improve the shear resistance and normal stress resistance,but reduce the toughness in the Ni–Mn–Cu–Ti alloy.And the ductility of the Co–Cu co-doping alloy is inferior to that of the Ni–Mn–Cu–Ti and Ni–Co–Mn–Ti alloys.The electronic density of states was studied to reveal the essence of the mechanical and magnetic properties.

孔隙和α-Al(Fe/Mn)Si相对高压压铸Al-7Si-0.2Mg合金塑性的影响

采用高压压铸工艺制备两批次不同尺寸的Al-7Si-0.2Mg(质量分数,%)合金,获得显微组织和孔隙非均匀分布的薄壁铸件,并对比研究孔隙和显微组织对铸态合金塑性的影响。结果表明:不同铸件和不同位置样品的伸长率有较大波动(9.7%~17.9%)。当合金存在大面积孔隙时,有效承载面积减小导致由孔隙产生的应力集中使合金伸长率显著降低。当合金只存在小面积孔隙时,塑性变形过程中合金中的α-Al(Fe/Mn)Si相先于共晶硅相发生脆性断裂,α-Al(Fe/Mn)Si相的数量密度对伸长率的波动起主导作用,具有高数量密度α-Al(Fe/Mn)Si相试样的伸长率显著降低。此外,局部较高的冷却速率导致铸件α-Al(Fe/Mn)Si相数量密度的增加。

Fe-Mn/TiO_(2)的制备及其催化臭氧氧化双酚A的性能研究

采用浸渍法制备Fe-Mn/TiO_(2)双金属催化材料,以双酚A(BPA)为目标降解物,探究了Fe-Mn/TiO_(2)对其的降解效果及降解机制。结果表明,Fe-Mn/TiO_(2)催化臭氧氧化降解BPA的去除率相较于单独TiO_(2)处理提升了83.4%;Fe、Mn成功负载且催化剂孔洞较丰富;相较于TiO_(2),Fe-Mn/TiO_(2)中锐钛矿质量分数增加能产生更多的羟基自由基。同时,Fe、Mn在TiO_(2)表面能发生价态转化,可作为活性位点促进臭氧分解为·OH等活性物质,增强催化反应活性。