Corrosion behavior of 2A97 Al-Cu-Li alloys in different thermomechanical conditions by quasi-in-situ analysis

As a promising material in the aircraft industry,2A97 Al-Cu-Li alloy exhibits high corrosion susceptibility that may limit its application.In the present work,to illustrate the influences of precipitate and grain-stored energy on localized corrosion evolution in 2A97 Al-Cu-Li alloy,cold working and artificial aging were carried out to produce 2A97 Al-Cu-Li alloys under different thermomechanical conditions.Quasi-in-situ analysis,traditional immersion test and electrochemical measurement were then conducted to examine the corrosion behavior of 2A97 alloys.It is revealed that precipitate significantly affects Cu enrichment at corrosion fronts,which determines corrosion susceptibility of alloys,whereas grain-stored energy distribution is closely associated with localized corrosion propagation.It is also indicated that quasi-in-situ analysis exhibits a consistent corrosion evolution with traditional immersion tests,which is regarded as a proper method to explore localized corrosion mechanisms by providing local microstructural information with enhanced time and spatial resolutions.

Improving comprehensive properties of Cu-11.9Al-2.5Mn shape memory alloy by adding multi-layer graphene carried by Cu_(51)Zr_(14)inoculant particles

In order to improve the comprehensive properties of the Cu-11.9Al-2.5Mn shape memory alloy(SMA),multilayer graphene(MLG)carried by Cu_(51)Zr_(14)inoculant particles was incorporated and dispersed into this alloy through preparing the preform of the cold-pressed MLG-Cu_(51)Zr_(14)composite powders.In the resultant novel MLG/Cu-Al-Mn composites,MLG in fragmented or flocculent form has a good bonding with the Cu-Al-Mn matrix.MLG can prevent the coarsening of grains of the Cu-Al-Mn SMA and cause thermal mismatch dislocations near the MLG/Cu-Al-Mn interfaces.The damping and mechanical properties of the MLG/Cu-Al-Mn composites are significantly improved.When the content of MLG reaches 0.2 wt.%,the highest room temperature damping of 0.0558,tensile strength of 801.5 MPa,elongation of 10.8%,and hardness of HV 308 can be obtained.On the basis of in-depth observation of microstructures,combined with the theory of internal friction and strengthening and toughening theories of metals,the relevant mechanisms are discussed.

Influence of thermomechanical treatment on recrystallization and softening resistance of Cu-6.5Fe-0.3Mg alloy

The recrystallization and softening resistance of a Cu-6.5Fe-0.3Mg(mass fraction,%)alloy prepared by Process 1(cold rolling heat treatment)and Process 2(hot/cold rolling heat treatment)were studied using Vickers hardness tests,tensile tests,scanning electron microscopy and transmission electron microscopy.The softening temperature,hardness and tensile strength of the alloy prepared by Process 2 were 110°C,HV 15 and 114 MPa higher,respectively,than those of the alloy prepared by Process 1 after aging at 300°C.The recrystallization activation energy of the alloys prepared by Process 1 and Process 2 were 72.83 and 98.11 kJ/mol,respectively.The pinning effects of the precipitates of the two alloys on grain boundaries and dislocations were basically the same.The softening mechanism was mainly attributed to the loss of dislocation strengthening.The higher Fe fiber density inhibited the average free migration path of dislocations and grain boundary migration in the alloy,which was the main reason for higher softening temperature of the alloy prepared by Process 2.

Microstructure of Al-Zn-Mg-Cu-Zr-0.5Er alloy under as-cast and homogenization conditions

The billets of Al-Zn-Mg-Cu-Zr and Al-Zn-Mg-Cu-Zr-0.5Er alloys were prepared by semi-continuous direct chill casting （DCC）.The effects of trace Er on microstructure of Al-Zn-Mg-Cu-Zr alloy under as-cast and homogenization conditions were studied.The results show that the grain morphology is large dendritic structure and the grain size increases obviously by the addition of 0.5% Er.Moreover,most of Er element in the alloy segregates at grain boundary during solidification,resulting in ternary Al8Cu4Er phase.After homogenization,most of the MgZn2 phase at grain boundary has dissolved back to Al matrix in the two alloys.In the Er-containing alloy,the dissolution temperature of Al8Cu4Er phase is about 575 °C.Therefore,the homogenization treatment cannot eliminate Al8Cu4Er phase validity.

Effects of grain refining and modification on mechanical properties and microstructures of Al-7.5Si-4Cu cast alloy

Al-7.5Si-4Cu cast alloy melt modified by Al-5Ti-B, RE and Al-10Sr master alloys were poured in the chromite sand moulds, to investigate comparatively the effects of individual or combined additions of grain refiners and modifiers on the mechanical properties, microstructures, grain refining and modification, and intermetallic compounds of the alloy. The results show that the mechanical properties and the microstructures of Al-7.5Si-4Cu cast alloys are improved immensely by combining addition of 0.8%Al-5Ti-B, 0.1%RE and 0.1%Al-10Sr grain refiners and modifiers compared with the individual addition and cast conditions. For individual addition condition, addition of 0.8%Al-5Ti-B master alloy can obtain superior tensile strength, Brinell hardness and finer equiaxedα（Al） dendrites. The alloy with 0.1%RE master alloy shows the highest improvement in ductility because the rare earth can purify the molten metal and change the shape of intermetallic compounds. While the alloy with 0.1%Al-10Sr modifier shows only good improvement in yield strength, and the improvement of other performance is unsatisfactory. The Al-10Sr modifier has a significant metamorphism for the eutectic silicon, but will make the gas content in the aluminum alloy melt increase to form serious columnar grain structures. The effects of grain refining and modification on mean area and aspect ratio have the same conclusions obtained in the mechanical properties and the microstructures analyses.

Investigation on sintering and deformation strengthening of Mo-Cu alloy

Mo-Swt%Cu nanocomposite powders were fabricated by mechanical alloying, and full density alloy was obtained via liquid-phase sintering and post-treatment process. The microstructure of Mo-8wt%Cu alloy was investigated by scanning elec-tron microscope （SEM） , and the effects of process parameters on relative density, tensile strength and elongation were stud-ied. The results indicate that the relative density of Mo-Cu alloy is 98. 6% after sintering at 1 250℃ for 30 min, and its micro-structure is composite network The full density of Mo-Cu alloy can be obtained when specimens are treated through deforma-tion strengthening process of rotating forging and hydrostatic extrusion The tensile strength and elongation rate are 576 MPa and 5. 8% ,respectively, when hydrostatic extrusion deformation degree is 40%.

粉末锻造Al_(2)O_(3)颗粒增强Fe–Ni–Mo–C–Cu复合材料的组织与性能

通过粉末锻造技术制备了不同含量微米级Al_(2)O_(3)颗粒强化的Fe–Ni–Mo–C–Cu(Q61)复合材料,并对调质态和淬火态复合材料的组织和性能进行了研究。结果表明:当Al_(2)O_(3)质量分数为0.15%时,增强颗粒在基体内分布均匀;相较于同种状态下不添加增强颗粒的单一Q61,调质态复合材料的硬度从HRC 38增至HRC 39.8,屈服强度从1106 MPa增至1121 MPa,延伸率从12%降至6.5%;淬火态复合材料的硬度从HRC 61.5增至HRC 63.2,磨损率从5.27×10^(-6)mm^(3)·m^(-1)·N^(-1)降至3.08×10^(-6)mm^(3)·m^(-1)·N^(-1),低于对比试验用的典型齿轮材料40Cr的磨损率(3.34×10^(-6)mm^(3)·m^(-1)·N^(-1))。当Al_(2)O_(3)质量分数大于0.15%时,Al_(2)O_(3)颗粒逐渐偏聚,虽然调质态下复合材料屈服强度仍继续小幅增加,但塑性严重退化,且淬火态复合材料磨损率增加,耐磨性变差。综合来看,添加0.15%Al_(2)O_(3)颗粒强化Q61复合材料在调质态下具有较高的综合力学性能,而在淬火态下表现出良好的抗摩擦磨损能力。

Synergistic effect of gradient Zn content and multiscale particles on the mechanical properties of Al-Zn-Mg-Cu alloys with coupling distribution of coarse-fine grains

This study investigated the influence of graded Zn content on the evolution of precipitated and iron-rich phases and grain struc-ture of the alloys,designed and developed the Al–8.0Zn–1.5Mg–1.5Cu–0.2Fe(wt%)alloy with high strength and formability.With the increase of Zn content,forming the coupling distribution of multiscale precipitates and iron-rich phases with a reasonable matching ratio and dispersion distribution characteristics is easy.This phenomenon induces the formation of cell-like structures with alternate distribu-tion of coarse and fine grains,and the average plasticity–strain ratio(characterizing the formability)of the pre-aged alloy with a high strength is up to 0.708.Results reveal the evolution and influence mechanisms of multiscale second-phase particles and the corresponding high formability mechanism of the alloys.The developed coupling control process exhibits considerable potential,revealing remarkable improvements in the room temperature formability of high-strength Al–Zn–Mg–Cu alloys.

强流脉冲电子束作用下Cu表面合金化Mo研究

钼(Mo)与铜(Cu)之间属于二元互不固溶体系,然而结合了Mo的高温硬度和强度以及Cu的导电导热等优异性能的Cu-Mo复合材料却在电触头、散热元件等领域有着重要的应用。存在的问题是Cu-Mo之间的固溶度极低,难以实现合金化,从而极大地限制了Cu-Mo复合材料优异性能的发挥。该研究尝试采用强流脉冲电子束(HCPEB)技术实现Cu-Mo互不固溶体系的合金化,从而达到改善材料表面力学性能的目的。利用HCPEB辐照预制Mo涂层粉的Cu基体进行辐照,研究不同脉冲次数对样品固溶度、相结构和表面硬度的影响。结果表明,HCPEB辐照可以有效提高Cu-Mo互不固溶体系的固溶度,15次辐照后,Mo在Cu基体中的固溶度达到最高;随辐照次数增加,Cu(Mo)固溶体受热脱溶影响导致合金层中的固溶度反而有所降低。微观结构图像显示,15次HCPEB辐照后样品表层中可观察到大量的球形以及摩尔形态的Mo颗粒;当辐照次数增加到35次后,Mo颗粒大多倾向于分布在晶体缺陷处,且脱溶析出的Mo颗粒与基体存在一定的取向关系。性能测试结果表明,HCPEB合金化处理后Cu(Mo)合金化表层的硬度与辐照次数呈统一变化趋势,即随辐照次数增加显著提升,固溶强化、位错强化和弥散强化机制的共同作用是合金化表层性能改善的原因之所在。

Preparation of CeO_2-Modified Mg(Al)O-Supported Pt–Cu Alloy Catalysts Derived from Hydrotalcite-Like Precursors and Their Catalytic Behavior for Direct Dehydrogenation of Propane

A series of PtCuCeMgAl quintuple hydrotalcite-like compounds with different Ce contents were synthesized by one-pot method. After calcining and reduction, CeO_2-modified Mg(Al)O-supported Pt–Cu alloy catalysts were obtained. To understand the effect of Cu and Ce, the structure and physico-chemistry properties of the catalysts were characterized and analyzed, and the catalytic behaviors were investigated in a direct dehydrogenation of propane to propene. The results show that the Pt^(4+), Cu^(2+), and Ce^(3+) ions can be incorporated into the brucite-like layers and the Ce content significantly affects the interaction strength between Pt and Cu and the dehydrogenation performance of propane. Under the reaction conditions, the highest propane conversion(45%) with 89% selectivity to propene and a 40% propene yield were achieved with a 0.3 wt% Ce-modified PtCu/Mg(Al)O catalyst. The improved catalytic performance is related to the easy formation of Pt–Cu alloy phase, excellent resistance to sintering, and coke deposits of active components modified by CeO_2.

Electrical conductivity of molten LiF–DyF3–Dy2O3–Cu2O system for Dy–Cu intermediate alloy production

Dy–Cu intermediate alloys have shown substantial potential in the field of magnetostrictive and magnetic refrigerant materials.Therefore,this study focused on investigating the electrical conductivity of molten-salt systems for the preparation of Dy–Cu alloys and on optimizing the corresponding operating parameters.The electrical conductivity of molten LiF–DyF3–Dy2O3–Cu2O systems was measured from 910 to 1030°C using the continuously varying cell constant method.The dependencies of the LiF–DyF3–Dy2O3–Cu2O system conductivity on the melt composition and temperature were examined herein.The optimal operating conditions for Dy–Cu alloy production were determined via analyses of the electrical conductivity and activation energies for conductance,which were calculated using the Arrhenius equation.The conductivity of the molten system regularly increases with increasing temperature and decreases with increasing concentration of Dy2O3 or Cu2O or both.The activation energy Eκof the LiF–DyF3–Dy2O3 and LiF–DyF3–Cu2O molten-salt systems increases with increasing Dy2O3 or Cu2O content.The regression functions of conductance as a function of temperature(t)and the addition of Dy2O3(W(Dy2O3))and Cu2O(W(Cu2O))can be expressed asκ=-2.08435+0.0068t-0.18929W(Dy2O3)-0.07918W(Cu2O).The optimal electrolysis conditions for preparing the Dy–Cu alloy in LiF–DyF3–Dy2O3–Cu2O molten salt are determined to be 2.0wt%≤W(Dy2O3)+W(Cu2O)≤3.0wt%and W(Dy2O3):W(Cu2O)=1:2 at 970 to 1000°C.

Microstructures of Sintered Mo-Cu Alloys with Mechanically Activated Powder

Mechanical activation and liquid phase sintering were used to manufacture high performance Mo-Cu alloy and develop new processes. The microstructures and properties of the alloy were investigated. The experimental results showed that: (1) the ball milled Mo/Cu powder has lamellar structure, (2) the microstructures of the sintered Mo-Cu alloy were homogenous compound structures of adhesive phase Cu linking Mo grains, (3) Mo grains frequently strung or gathered in Cu phase, and (4) the full densities of Mo-Cu alloy was achieved through sintering and special densification process. As a result, the properties of the alloy are good enough to satisfy various requirements.

AZ31镁合金基Cu-MOF-SA超疏水膜的制备及其耐腐蚀性能研究

腐蚀是影响镁及其合金大规模应用的关键技术难题之一,因可有效隔离金属基底与腐蚀介质的直接接触,从而降低腐蚀速率,制备超疏水表面成为提高镁合金耐蚀性的有效途径。通过一步电沉积方法,在AZ31镁合金基底上成功制备了铜-金属有机骨架-硬脂酸(Cu-MOF-SA)超疏水膜,并对超疏水膜的耐腐蚀性、化学稳定性和耐热性进行了综合研究。结果表明,表面的水接触角可达158°,超疏水膜覆盖的试样在3.5%NaCl溶液中表现出良好的耐腐蚀性能,相比AZ31镁合金基底,其腐蚀电位正移了0.24 V,腐蚀电流密度降低了1个数量级。在pH值为1~14的溶液中浸润24 h后,超疏水膜的水接触角仍可达135°以上,浸泡在pH=1的溶液24 h的超疏水膜的腐蚀电位比AZ31镁合金基底高0.21 V。在20~90℃空气中保温24 h后,超疏水膜的水接触角仍保持在154°以上,80℃下保温24 h后其腐蚀电位比AZ31镁合金基底的高0.22 V,腐蚀电流密度比AZ31镁合金基底的小1个数量级。结果表明,本研究制备的Cu-MOF-SA疏水膜具有良好的超疏水性和耐腐蚀性。

Densification of Mo Alloys at 1473 K by Adding Ni-Cu Solid Solution

Mo is difficult to sinter densely at a relatively low temperature due to its high melting point. In the present paper,by adding different weight contents of Ni and Cu additives, Mo alloys have been densified at 1473 K for an hour byhot-pressing method, and the optimum contents of Cu and Ni additives have been acquired: when the contents of Niand Cu are 3 and 2 wt pct respectively, the relative density of the sample reaches the maximum value. It was foundthat when the Ni-Cu solid solution was added into Mo alloys. the achieved density is higher than the case of Ni andCu additives. The experimental results indicate that, Ni and Cu play different roles in the process of sintering, theNi-Cu solid solution has the same function as Ni and Cu additives in the course of sintering Mo alloys, It shows moreactivating sintering feature for Mo than the Ni and Cu additives.

Microstructure and mechanical properties of hypereutectic Al-Si alloy modified with Cu-P

The microstructure and mechanical properties of Al-14.6Si castings modified by Cu-P master alloy under different conditions were studied with optical microscope（OM） and mechanical testing and simulation（MTS）.The results indicate that the Cu-P master alloy possesses not only obvious modification effect,but also longevity effect with more than 8 h on the hypereutectic Al-Si alloy.It is shown from thermal calculation,scanning electron microscope（SEM）,and energy dispersive analysis of X-rays（EDAX） that the modification mechanism of Cu-P on primary silicon in the castings is heterogeneous nucleation around AlP particles.The Cu-P master alloy has no or little modifying effect on eutectic silicon,even though it has obvious modification on primary silicon in the castings.This may be because of the fast transformation of eutectic silicon at a very narrow temperature,which will notably weaken the role of AlP particles as heterogeneous nuclei for eutectic silicon.

Relationship among solution heating rate,mechanical properties,microstructure and texture of Al−Mg−Si−Cu alloy

The relationship among heating rate, mechanical properties, microstructure and texture of Al-Mg-Si-Cu alloy during solution treatment was investigated through tensile test, scanning electron microscope, X-ray diffractometer and EBSD technology. The experimental results reveal that there is a non-monotonic relationship among solution heating rate, mechanical properties, microstructure and texture. As the solution heating rate increases, the strength variations are dependent on the tensile direction;work hardening exponent n decreases first, and then increases;plastic strain ratio r increases first, and then decreases, and finally increases. The final microstructure and texture are also affected by heating rate. As heating rate increases, the microstructure transforms from elongated grain structure to equiaxed grain structure, and the average grain size decreases first, and then increases, and decreases finally. Although the texture components including CubeND{001}<310> and P{011}<122> orientations almost have no change with the increase of heating rate, the texture intensity and volume fraction decrease first, and then increase, and finally decrease. Both microstructure and texture evolutions are weakly affected by heating rate. Improving heating rate is not always favorable for the development of fine equiaxed grain structure, weak texture and high average r value, which may be related to the recrystallization behavior.

Brazeability evaluation of Ti-Zr-Cu-Ni-Co-Mo filler for vacuum brazing TiAl-based alloy

Ti-47Al-2Nb-2Cr-0.15B(mole fraction,%)alloy was vacuum brazed with amorphous and crystalline Ti.25Zr-12.5Cu-12.5Ni-3.0Co-2.0Mo(mass fraction,%)filler alloys,and the melting,spreading and gap filling behaviors of the amorphous and crystalline filler alloys as well as the joints brazed with them were investigated in details.Results showed that the amorphous filler alloy possessed narrower melting temperature interval,lower liquidus temperature and melting active energy compared with the crystalline filler alloy,and it also exhibited better brazeability on the surface of the Ti.47Al.2Nb.2Cr.0.15B alloy.The TiAl joints brazed with crystalline and amorphous filler alloys were composed of two interfacial reaction layers and a central brazed layer.Under the same conditions,the tensile strength of the joint brazed with the amorphous filler alloy was always higher than that with the crystalline filler alloy.The maxmium tensile strength of the joint brazed at 1273 K with the amorphous filler alloy reached 254 MPa.

Strengthening mechanism of T8-aged Al-Cu-Li alloy with increased pre-deformation

The microstructure evolution and mechanical properties of a T8-aged Al-Cu-Li alloy with increased pre-deformation(0-15%) were investigated,revealing the microstructure-strength relationship and the intrinsic strengthening mechanism.The results show that increasing the pre-deformation levels remarkably improves the strength of the alloy but deteriorates its ductility.Dislocations introduced by pre-deformation effectively suppress the formation of Guinier-Preston(GP) zones and provide more nucleation sites for T1 precipitates.This leads to more intensive and finer T1 precipitates in the samples with higher pre-deformation levels.Simultaneously,the enhanced precipitation of T1 precipitates and inhibited formation of GP zones cause the decreases in number and sizes of θ′ precipitates.The quantitative descriptions of the strength contributions from different strengthening mechanisms reveal that strengthening contributions from T1 and θ′ precipitates decrease with increasing pre-deformation.The reduced diameters of T1 precipitates are primarily responsible for their weakened strengthening effects.Therefore,the improved strength of the T8-aged Al-Cu-Li alloy is mainly attributed to the stronger strain hardening from the increased pre-deformation levels.

Relationship between amounts of low-melting-point eutectics and hot tearing susceptibility of ternary Al−Cu−Mg alloys during solidification

A systematical study on the relationship between the amounts of different eutectic phases especially the low-melting-point(LMP)eutectics and the hot tearing susceptibility of ternary Al−Cu−Mg alloys during solidification was performed.By controlling the concentrations of major alloying elements(Cu,Mg),the amounts of LMP eutectics at the final stages of solidification were varied and the corresponding hot tearing susceptibility(HTS)was determined.The results showed that the Al−4.6Cu−0.4Mg(wt.%)alloy,which contained the smallest fraction of LMP eutectics among the investigated alloys,was observed to be the most susceptible to hot tearing.With the amount of total residual liquid being approximately the same in the alloys,the hot tearing resistance is considered to be closely related to the amounts of LMP eutectics.Specifically,the higher the amount of LMP eutectics was,the lower the HTS of the alloy was.Further,the potential mechanism of low HTS for alloys with high amounts of LMP eutectics among ternary Al−Cu−Mg alloys was discussed in terms of feeding ability and permeability as well as total viscosity evolution during solidification.

Damage characteristics of Cu−Cr−Zr alloy rail of electromagnetic railgun after simulated launch

The damage characteristics of different speed sections of Cu−Cr−Zr alloy rail after simulated launch were studied.The microstructure,morphologies and properties of samples were investigated by using XRD,XPS,EBSD,SEM,hardness test,electrochemical test and DSC techniques.It was found that deposition layers were formed on the surfaces of the simulated launch samples.The thickness and surface roughness of these deposition layers increased with increasing the heat effect,suggesting a launch speed dependent damage degree of the arc ablation.The hardness variation of samples is attributed to the effects of the deposition layer and deformation hardening.The surface deposition layer affects corrosion resistance and crystalline characteristics,leading to changes in subsequent service performances.Additionally,the surface texture and plastic deformation ability of the samples are related to the recrystallization degree and deformation grain amount.