On December 18,2023,an M_(s)6.2 earthquake occurred in Jishishan,Gansu Province,China.This earthquake happened in the eastern region of the Qilian Orogenic Belt,which is situated at the forefront of the NE margin of t...On December 18,2023,an M_(s)6.2 earthquake occurred in Jishishan,Gansu Province,China.This earthquake happened in the eastern region of the Qilian Orogenic Belt,which is situated at the forefront of the NE margin of the Tibetan Plateau(i.e.,Qinghai-Tibet Plateau),encompassing a rhombic-shaped area that intersects the Qilian-Qaidam Basin,Alxa Block,Ordos Block,and South China Block.In this study,we analyzed the deep tectonic pattern of the Jishishan earthquake by incorporating data on the crustal thickness,velocity structure,global navigation satellite system(GNSS)strain field,and anisotropy.We discovered that the location of the earthquake was related to changes in the crustal structure.The results showed that the Jishishan M_(s)6.2 earthquake occurred in a unique position,with rapid changes in the crustal thickness,Vp/Vs,phase velocity,and S-wave velocity.The epicenter of the earthquake was situated at the transition zone between high and low velocities and was in proximity to a low-velocity region.Additionally,the source area is flanked by two high-velocity anomalies from the east and west.The principal compressive strain orientation near the Lajishan Fault is primarily in the NNE and NE directions,which align with the principal compressive stress direction in this region.In some areas of the Lajishan Fault,the principal compressive strain orientations show the NNW direction,consistent with the direction of the upper crustal fast-wave polarization from local earthquakes and the phase velocity azimuthal anisotropy.These features underscore the relationship between the occurrence of the Jishishan M_(s)6.2 earthquake and the deep inhomogeneous structure and deep tectonic characteristics.The NE margin of the Tibetan Plateau was thickened by crustal extension in the process of northeastward expansion,and the middle and lower crustal materials underwent structural deformation and may have been filled with salt-containing fluids during the extension process.The presence of this weak layer makes it easier for strong earthquakes to occur through the release of overlying rigid crustal stresses.However,it is unlikely that an earthquake of comparable or larger magnitude would occur in the short term(e.g.,in one year)at the Jishishan east margin fault.展开更多
On September 5, 2022, a magnitude Ms 6.8 earthquake occurred along the Moxi fault in the southern part of the Xianshuihe fault zone located in the southeastern margin of the Tibetan Plateau,resulting in severe damage ...On September 5, 2022, a magnitude Ms 6.8 earthquake occurred along the Moxi fault in the southern part of the Xianshuihe fault zone located in the southeastern margin of the Tibetan Plateau,resulting in severe damage and substantial economic loss. In this study, we established a coseismic landslide database triggered by Luding Ms 6.8 earthquake, which includes 4794 landslides with a total area of 46.79 km^(2). The coseismic landslides primarily consisted of medium and small-sized landslides, characterized by shallow surface sliding. Some exhibited characteristics of high-position initiation resulted in the obstruction or partial obstruction of rivers, leading to the formation of dammed lakes. Our research found that the coseismic landslides were predominantly observed on slopes ranging from 30° to 50°, occurring at between 1000 m and 2500 m, with slope aspects varying from 90° to 180°. Landslides were also highly developed in granitic bodies that had experienced structural fracturing and strong-tomoderate weathering. Coseismic landslides concentrated within a 6 km range on both sides of the Xianshuihe and Daduhe fault zones. The area and number of coseismic landslides exhibited a negative correlation with the distance to fault lines, road networks, and river systems, as they were influenced by fault activity, road excavation, and river erosion. The coseismic landslides were mainly distributed in the southeastern region of the epicenter, exhibiting relatively concentrated patterns within the IX-degree zones such as Moxi Town, Wandong River basin, Detuo Town to Wanggangping Township. Our research findings provide important data on the coseismic landslides triggered by the Luding Ms 6.8 earthquake and reveal the spatial distribution patterns of these landslides. These findings can serve as important references for risk mitigation, reconstruction planning, and regional earthquake disaster research in the earthquake-affected area.展开更多
Based on the understanding that the seismic fault system is a nonlinear complex system,Rundle(1995)introduced the nonlinear threshold system used in meteorology to analyze the ocean-atmosphere interface and the El Ni?...Based on the understanding that the seismic fault system is a nonlinear complex system,Rundle(1995)introduced the nonlinear threshold system used in meteorology to analyze the ocean-atmosphere interface and the El Ni?o Southern Oscillation into the study of seismic activity changes,and then proposed the PI method(Rundle et al.,2000a,b).Wu et al.(2011)modified the Pattern Informatics Method named MPI to extract the ionospheric anomaly by using data from DEMETER satellites which is suitable for 1–3 months short-term prediction.展开更多
Cemented and mechanically clamped types of end fittings(fitting-C and fitting-M)are commonly used in transformer bushings.During the Luding Ms 6.8 earthquake that occurred in China on September 5,2022,all transformer ...Cemented and mechanically clamped types of end fittings(fitting-C and fitting-M)are commonly used in transformer bushings.During the Luding Ms 6.8 earthquake that occurred in China on September 5,2022,all transformer bushings with the two types of end fittings in a 500 kV substation were damaged.Post-earthquake field investigations were conducted,and the failures of the two types of bushings were compared.Two elementary simulation models of the transformer-bushing systems were developed to simulate the engineering failures,and further compute their seismic responses for comparison.The results indicate that the hitch lugs of the connection flange are structurally harmful to seismic resistance.Fitting-M can decrease the bending stiffness of the bushing due to the flexible sealing rubber gasket.Since it provides a more flexible connection that dissipates energy,the peak accelerations and relative displacements at the top of the bushing are significantly lower than those of the bushing with fitting-C.Compared with fitting-C,fitting-M transfers the high-stress areas from the connection flange to the root of the porcelain,so the latter becomes the most vulnerable component.Fitting-M increases the failure risk of the low-strength porcelain,indicating the unsuitability of applying it in high-intensity fortification regions.展开更多
According to news reports on severe earthquakes since 2008,a total of 51 cases with magnitudes of 6.0 or above were analyzed,and 14 frequently occurring secondary disasters were identified.A disaster chain model was d...According to news reports on severe earthquakes since 2008,a total of 51 cases with magnitudes of 6.0 or above were analyzed,and 14 frequently occurring secondary disasters were identified.A disaster chain model was developed using principles from complex network theory.The vulnerability and risk level of each edge in this model were calculated,and high-risk edges and disaster chains were identified.The analysis reveals that the edge“floods→building collapses”has the highest vulnerability.Implementing measures to mitigate this edge is crucial for delaying the spread of secondary disasters.The highest risk is associated with the edge“building collapses→casualties,”and increased risks are also identified for chains such as“earthquake→building collapses→casualties,”“earthquake→landslides and debris flows→dammed lakes,”and“dammed lakes→floods→building collapses.”Following an earthquake,the prompt implementation of measures is crucial to effectively disrupt these chains and minimize the damage from secondary disasters.展开更多
The Ms 6.4 earthquake occurred on May 21,2021 in Yangbi County,Dali Prefecture,Yunnan Province,which was the largest earthquake after the 2014 Jinggu Ms 6.6 earthquake,in western Yunnan.After the earthquake,the rapid ...The Ms 6.4 earthquake occurred on May 21,2021 in Yangbi County,Dali Prefecture,Yunnan Province,which was the largest earthquake after the 2014 Jinggu Ms 6.6 earthquake,in western Yunnan.After the earthquake,the rapid field investigation and earthquake relocation reveal that there was no obvious surface rupture and the earthquake did not occur on pre-existing active fault,but on a buried fault on the west side of Weixi–Qiaohou–Weishan fault zone in the eastern boundary of Baoshan sub-block.Significant foreshocks appeared three days before the earthquake.These phenomena aroused scholars'intensive attention.What the physical process and seismogenic mechanism of the Yangbi Ms 6.4 earthquake are revealed by the foreshocks and aftershocks?These scientific questions need to be solved urgently.展开更多
In the past two decades,because of the significant increase in the availability of differential interferometry from synthetic aperture radar and GPS data,spaceborne geodesy has been widely employed to determine the co...In the past two decades,because of the significant increase in the availability of differential interferometry from synthetic aperture radar and GPS data,spaceborne geodesy has been widely employed to determine the co-seismic displacement field of earthquakes.On April 18,2021,a moderate earthquake(Mw 5.8)occurred east of Bandar Ganaveh,southern Iran,followed by intensive seismic activity and aftershocks of various magnitudes.We use two-pass D-InSAR and Small Baseline Inversion techniques via the LiCSBAS suite to study the coseismic displacement and monitor the four-month post-seismic deformation of the Bandar Ganaveh earthquake,as well as constrain the fault geometry of the co-seismic faulting mechanism during the seismic sequence.Analyses show that the co-and postseismic deformation are distributed in relatively shallow depths along with an NW-SE striking and NE dipping complex reverse/thrust fault branches of the Zagros Mountain Front Fault,complying with the main trend of the Zagros structures.The average cumulative displacements were obtained from-137.5 to+113.3 mm/yr in the SW and NE blocks of the Mountain Front Fault,respectively.The received maximum uplift amount is approximately consistent with the overall orogen-normal shortening component of the Arabian-Eurasian convergence in the Zagros region.No surface ruptures were associated with the seismic source;therefore,we propose a shallow blind thrust/reverse fault(depth~10 km)connected to the deeper basal decollement fault within a complex tectonic zone,emphasizing the thin-skinned tectonics.展开更多
After the September 5,2022(Beijing time).Luding Ms6.8 earthquake(29.59°N.102.08°E.depth 16 km.according to the initial determination by the China Earthquake Networks Center(CENC)).field investigation was car...After the September 5,2022(Beijing time).Luding Ms6.8 earthquake(29.59°N.102.08°E.depth 16 km.according to the initial determination by the China Earthquake Networks Center(CENC)).field investigation was carried out by the China Earthquake Administration(CEA).which associated the earthquake to the Moxi segment on the south part of the Xianshuihe fault system.This segment,with horizontal slip rate 5-10 mm/a.locates in the convergent part among the Xianshuihe fault.展开更多
Stochastic finite-fault simulations are effective for simulating ground motions and are widely used in engineering to determine the impacts of ground motion and develop relevant predictive equations.In this study,the ...Stochastic finite-fault simulations are effective for simulating ground motions and are widely used in engineering to determine the impacts of ground motion and develop relevant predictive equations.In this study,the source,path,and site amplification coefficient of western Sichuan Province,China,and stochastic finite-fault simulations were used to simulate the acceleration time series,Fourier amplitude spectra,and 5%damped response spectra of 28 strong-motion stations with rupture distances within 300 km of the 2022 MS6.8 Luding earthquake.The simulation results of 14 stations at rupture distances of 45-185 km match the observation.However,the simulation results of 3 near-and 6 far-field stations at rupture distances of 12-36 km and 222-286 km,respectively,were obviously deviated from the observations.Simulation results of the near-field stations are larger than the observations at high frequencies(>6 Hz).The discrepancy likely comes from the nonlinear site effect of near-field stations,which reduced the site amplification at high frequencies.Simulation result of the far-field stations is smaller than the observation at frequencies above 1 Hz.As these stations are located close to the Longmenshan Fault Zone(LFZ),thus,we obtained a new quality factor(Q)from data of historical events and stations located around LFZ.Using the new Q value,the discrepancies of the high-frequency simulation results of the far-field stations were corrected.This result indicated that the laterally varying Q values can be used to address the impact of strong crustal lateral heterogeneity on simulation.展开更多
At 12:52 pm on September 5,2022,an Ms 6.8 earthquake occurred in Luding County,Sichuan Province,China.Based on high-resolution aerial photographs and satellite imageries obtained after the earthquake,as well as field ...At 12:52 pm on September 5,2022,an Ms 6.8 earthquake occurred in Luding County,Sichuan Province,China.Based on high-resolution aerial photographs and satellite imageries obtained after the earthquake,as well as field investigation,a total of 8685 earthquake-triggered landslides(EQTLs)were interpreted.The landslides covered an area of 30.7km^(2),with a source area of 9.4 km^(2).These EQTLs were mainly distributed in areas with a seismic intensity of VIII and IX.Most of the landslides were small and medium in size,and their types included landslide,rockfall,and rock slump.Characteristic landslide distributions were found,EQTLs were distributed along the Xianshuihe fault,landslide area decreased gradually with an increased distance to the fault;EQTLs were distributed along the Daduhe River and roads;besides,landslide distribution was associated with ground deformation caused by the earthquake.EQTLs’characteristics indicated that,a large number of EQTLs were located near the foot of the slope;the full area of EQTLs and their source area followed a power function.This study concluded that Luding EQTLs were greater in number and area but relatively smaller in terms of affected area.Investigations on geo-hazards post-earthquake and risk assessment were proposed in the earthquake-stricken area to support the rehabilitation and reconstruction.展开更多
On August 6,2023,a magnitude MW5.5 earthquake struck Pingyuan County,Dezhou City,Shandong Province,China.This event was significant as no large earthquakes had been recorded in the region for over a century,and no act...On August 6,2023,a magnitude MW5.5 earthquake struck Pingyuan County,Dezhou City,Shandong Province,China.This event was significant as no large earthquakes had been recorded in the region for over a century,and no active fault had been previously identified.This study collects 1309 P-wave arrival times and 866 S-wave arrival times from 74 seismic stations less than 200 km to the epicenter to constrain the spatial distribution of the mainshock and its 125 early aftershocks by the double difference earthquake relocation method,and selects 864 P-waveforms from 288 stations located within 800 km of the epicenter to constrain the focal mechanism solution of the mainshock through centroid moment tensor inversion.The relocation and the inversion indicate,the Pingyuan MW5.5 earthquake was caused by a rupture on a buried fault,likely an extensive segment of the Gaotang fault.This buried fault exhibited a dip of approximately 75°to the northwest,with a strike of 222°,similar to the Gaotang fault.The rupture initiated at the depth of 18.6 km and propagated upward and northeastward.However,the ground surface was not broken.The total duration of the rupture was~6.0 s,releasing the scalar moment of 2.5895×1017 N·m,equivalent to MW5.54.The moment rate reached the maximum only 1.4 seconds after the rupture initiation,and the 90%scalar moment was released in the first 4.6 s.In the first 1.4 seconds of the rupture process,the rupture velocity was estimated to be 2.6 km/s,slower than the local S-wave velocity.As the rupture neared its end,the rupture velocity decreased significantly.This study provides valuable insights into the seismic characteristics of the Pingyuan MW5.5 earthquake,shedding light on the previously unidentified buried fault responsible for the seismic activity in the region.Understanding the behavior of such faults is crucial for assessing seismic hazards and enhancing earthquake preparedness in the future.展开更多
The M6.2 earthquake in Jishishan,Gansu Province,on December 18,2023,caused extraordinary earthquake disasters.It was located in the northern part of the north−south seismic zone,which is a key area for earthquake moni...The M6.2 earthquake in Jishishan,Gansu Province,on December 18,2023,caused extraordinary earthquake disasters.It was located in the northern part of the north−south seismic zone,which is a key area for earthquake monitoring in China.The newly built dense strong motion stations in this area provide unprecedented conditions for high-precision earthquake relocation,especially the earthquake focal depth.This paper uses the newly built strong motion and traditional broadband seismic networks to relocate the source locations of the M3.0 and above aftershocks and to invert their focal mechanisms.The horizontal error of earthquake location is estimated to be 0.5−1 km,and the vertical error is 1−2 km.The focal depth range of aftershocks is 9.6−14.6 km,distributed in a 12-km-long strip with SSE direction.Aftershocks in the south are more concentrated horizontally and vertically,while aftershocks in the north are more scattered.The focal mechanisms of the main shock and aftershocks are relatively consistent,and the P-axis orientation is consistent with the regional strain direction.There is a seismic blank area of M3.0 and above,about 3−5 km between the main shock and aftershocks.It is suggested that the energy released by the main shock rupture is concentrated in this area.Based on the earthquake location and focal mechanism of the main shock,it is inferred that the Northern Lajishan fault zone is the seismogenic structure of the main shock,and the main shock did not occur on the main fault,but on a secondary fault.The initial rupture depth and centroid depth of the main shock were 12.8 and 14.0 km,respectively.The source rupture depth may not be the main reason for the severe earthquake disaster.展开更多
In order to investigate the role of the amplification of peak ground acceleration(PGA) in seismic landslide formation mechanisms and study how earthquake waves interact with rock structures, a few strong-motion seismo...In order to investigate the role of the amplification of peak ground acceleration(PGA) in seismic landslide formation mechanisms and study how earthquake waves interact with rock structures, a few strong-motion seismometers are installed at various locations on both sides of the Lengzhuguan gully. Five strong-motion seismometers were triggered at different depths in a tunnel at the same altitude during the Kangding Ms 5.8 earthquake on November 25 th, 2014. The data reveal that the horizontal peak acceleration(PGA_H) at each site decreased with increasing site depths. The PGAH at the deepest monitoring site(99 m from the tunnel entrance) was approximately half that of the outermost site. The amplitude of the acceleration response spectrum was also attenuated from the entrance inwards, the dynamic magnification factor(β) of the standard acceleration spectrum was less than 3.5, and rate of change was the same as that for the amplitude acceleration response. The Fourier spectra of each monitoring site also decreased from the outside inwards, and the components of the Fourier spectra were more complex at the surface.展开更多
基金the National Natural Science Foundation of China(Project Nos.41804046 and 41974050)the Special Fund of the Key Laboratory of Earthquake Prediction,China Earthquake Administration(No.CEAIEF2022010100).
文摘On December 18,2023,an M_(s)6.2 earthquake occurred in Jishishan,Gansu Province,China.This earthquake happened in the eastern region of the Qilian Orogenic Belt,which is situated at the forefront of the NE margin of the Tibetan Plateau(i.e.,Qinghai-Tibet Plateau),encompassing a rhombic-shaped area that intersects the Qilian-Qaidam Basin,Alxa Block,Ordos Block,and South China Block.In this study,we analyzed the deep tectonic pattern of the Jishishan earthquake by incorporating data on the crustal thickness,velocity structure,global navigation satellite system(GNSS)strain field,and anisotropy.We discovered that the location of the earthquake was related to changes in the crustal structure.The results showed that the Jishishan M_(s)6.2 earthquake occurred in a unique position,with rapid changes in the crustal thickness,Vp/Vs,phase velocity,and S-wave velocity.The epicenter of the earthquake was situated at the transition zone between high and low velocities and was in proximity to a low-velocity region.Additionally,the source area is flanked by two high-velocity anomalies from the east and west.The principal compressive strain orientation near the Lajishan Fault is primarily in the NNE and NE directions,which align with the principal compressive stress direction in this region.In some areas of the Lajishan Fault,the principal compressive strain orientations show the NNW direction,consistent with the direction of the upper crustal fast-wave polarization from local earthquakes and the phase velocity azimuthal anisotropy.These features underscore the relationship between the occurrence of the Jishishan M_(s)6.2 earthquake and the deep inhomogeneous structure and deep tectonic characteristics.The NE margin of the Tibetan Plateau was thickened by crustal extension in the process of northeastward expansion,and the middle and lower crustal materials underwent structural deformation and may have been filled with salt-containing fluids during the extension process.The presence of this weak layer makes it easier for strong earthquakes to occur through the release of overlying rigid crustal stresses.However,it is unlikely that an earthquake of comparable or larger magnitude would occur in the short term(e.g.,in one year)at the Jishishan east margin fault.
基金supported by the National Natural Science Foundation of China project (No. 42372339)the China Geological Survey Project (Nos. DD20221816, DD20190319)。
文摘On September 5, 2022, a magnitude Ms 6.8 earthquake occurred along the Moxi fault in the southern part of the Xianshuihe fault zone located in the southeastern margin of the Tibetan Plateau,resulting in severe damage and substantial economic loss. In this study, we established a coseismic landslide database triggered by Luding Ms 6.8 earthquake, which includes 4794 landslides with a total area of 46.79 km^(2). The coseismic landslides primarily consisted of medium and small-sized landslides, characterized by shallow surface sliding. Some exhibited characteristics of high-position initiation resulted in the obstruction or partial obstruction of rivers, leading to the formation of dammed lakes. Our research found that the coseismic landslides were predominantly observed on slopes ranging from 30° to 50°, occurring at between 1000 m and 2500 m, with slope aspects varying from 90° to 180°. Landslides were also highly developed in granitic bodies that had experienced structural fracturing and strong-tomoderate weathering. Coseismic landslides concentrated within a 6 km range on both sides of the Xianshuihe and Daduhe fault zones. The area and number of coseismic landslides exhibited a negative correlation with the distance to fault lines, road networks, and river systems, as they were influenced by fault activity, road excavation, and river erosion. The coseismic landslides were mainly distributed in the southeastern region of the epicenter, exhibiting relatively concentrated patterns within the IX-degree zones such as Moxi Town, Wandong River basin, Detuo Town to Wanggangping Township. Our research findings provide important data on the coseismic landslides triggered by the Luding Ms 6.8 earthquake and reveal the spatial distribution patterns of these landslides. These findings can serve as important references for risk mitigation, reconstruction planning, and regional earthquake disaster research in the earthquake-affected area.
基金supported by the Joint Funds of the National Natural Science Foundation of China(Grant No.U2039207)。
文摘Based on the understanding that the seismic fault system is a nonlinear complex system,Rundle(1995)introduced the nonlinear threshold system used in meteorology to analyze the ocean-atmosphere interface and the El Ni?o Southern Oscillation into the study of seismic activity changes,and then proposed the PI method(Rundle et al.,2000a,b).Wu et al.(2011)modified the Pattern Informatics Method named MPI to extract the ionospheric anomaly by using data from DEMETER satellites which is suitable for 1–3 months short-term prediction.
基金National Natural Science Foundation of China under Grant No.51878508。
文摘Cemented and mechanically clamped types of end fittings(fitting-C and fitting-M)are commonly used in transformer bushings.During the Luding Ms 6.8 earthquake that occurred in China on September 5,2022,all transformer bushings with the two types of end fittings in a 500 kV substation were damaged.Post-earthquake field investigations were conducted,and the failures of the two types of bushings were compared.Two elementary simulation models of the transformer-bushing systems were developed to simulate the engineering failures,and further compute their seismic responses for comparison.The results indicate that the hitch lugs of the connection flange are structurally harmful to seismic resistance.Fitting-M can decrease the bending stiffness of the bushing due to the flexible sealing rubber gasket.Since it provides a more flexible connection that dissipates energy,the peak accelerations and relative displacements at the top of the bushing are significantly lower than those of the bushing with fitting-C.Compared with fitting-C,fitting-M transfers the high-stress areas from the connection flange to the root of the porcelain,so the latter becomes the most vulnerable component.Fitting-M increases the failure risk of the low-strength porcelain,indicating the unsuitability of applying it in high-intensity fortification regions.
基金National Key Research and Development Program of China(No.2022YFC3803000).
文摘According to news reports on severe earthquakes since 2008,a total of 51 cases with magnitudes of 6.0 or above were analyzed,and 14 frequently occurring secondary disasters were identified.A disaster chain model was developed using principles from complex network theory.The vulnerability and risk level of each edge in this model were calculated,and high-risk edges and disaster chains were identified.The analysis reveals that the edge“floods→building collapses”has the highest vulnerability.Implementing measures to mitigate this edge is crucial for delaying the spread of secondary disasters.The highest risk is associated with the edge“building collapses→casualties,”and increased risks are also identified for chains such as“earthquake→building collapses→casualties,”“earthquake→landslides and debris flows→dammed lakes,”and“dammed lakes→floods→building collapses.”Following an earthquake,the prompt implementation of measures is crucial to effectively disrupt these chains and minimize the damage from secondary disasters.
文摘The Ms 6.4 earthquake occurred on May 21,2021 in Yangbi County,Dali Prefecture,Yunnan Province,which was the largest earthquake after the 2014 Jinggu Ms 6.6 earthquake,in western Yunnan.After the earthquake,the rapid field investigation and earthquake relocation reveal that there was no obvious surface rupture and the earthquake did not occur on pre-existing active fault,but on a buried fault on the west side of Weixi–Qiaohou–Weishan fault zone in the eastern boundary of Baoshan sub-block.Significant foreshocks appeared three days before the earthquake.These phenomena aroused scholars'intensive attention.What the physical process and seismogenic mechanism of the Yangbi Ms 6.4 earthquake are revealed by the foreshocks and aftershocks?These scientific questions need to be solved urgently.
文摘In the past two decades,because of the significant increase in the availability of differential interferometry from synthetic aperture radar and GPS data,spaceborne geodesy has been widely employed to determine the co-seismic displacement field of earthquakes.On April 18,2021,a moderate earthquake(Mw 5.8)occurred east of Bandar Ganaveh,southern Iran,followed by intensive seismic activity and aftershocks of various magnitudes.We use two-pass D-InSAR and Small Baseline Inversion techniques via the LiCSBAS suite to study the coseismic displacement and monitor the four-month post-seismic deformation of the Bandar Ganaveh earthquake,as well as constrain the fault geometry of the co-seismic faulting mechanism during the seismic sequence.Analyses show that the co-and postseismic deformation are distributed in relatively shallow depths along with an NW-SE striking and NE dipping complex reverse/thrust fault branches of the Zagros Mountain Front Fault,complying with the main trend of the Zagros structures.The average cumulative displacements were obtained from-137.5 to+113.3 mm/yr in the SW and NE blocks of the Mountain Front Fault,respectively.The received maximum uplift amount is approximately consistent with the overall orogen-normal shortening component of the Arabian-Eurasian convergence in the Zagros region.No surface ruptures were associated with the seismic source;therefore,we propose a shallow blind thrust/reverse fault(depth~10 km)connected to the deeper basal decollement fault within a complex tectonic zone,emphasizing the thin-skinned tectonics.
基金This work is supported by the National Natural Science Foundation of China(Nos.U2039207 and 42004038)National Key Research and Development Program of China(No.2018YFE0109700)the Special Fund of the Institute of Earthquake Forecasting,China Earthquake Administration(No.CEAIEF2022030206).
文摘After the September 5,2022(Beijing time).Luding Ms6.8 earthquake(29.59°N.102.08°E.depth 16 km.according to the initial determination by the China Earthquake Networks Center(CENC)).field investigation was carried out by the China Earthquake Administration(CEA).which associated the earthquake to the Moxi segment on the south part of the Xianshuihe fault system.This segment,with horizontal slip rate 5-10 mm/a.locates in the convergent part among the Xianshuihe fault.
基金supported by the Special Fund of the Institute of Geophysics,China Earthquake Administration(Nos.DQJB2B28 and DQJB22X09)the National Natural Science Foundation of China(No.52192675).
文摘Stochastic finite-fault simulations are effective for simulating ground motions and are widely used in engineering to determine the impacts of ground motion and develop relevant predictive equations.In this study,the source,path,and site amplification coefficient of western Sichuan Province,China,and stochastic finite-fault simulations were used to simulate the acceleration time series,Fourier amplitude spectra,and 5%damped response spectra of 28 strong-motion stations with rupture distances within 300 km of the 2022 MS6.8 Luding earthquake.The simulation results of 14 stations at rupture distances of 45-185 km match the observation.However,the simulation results of 3 near-and 6 far-field stations at rupture distances of 12-36 km and 222-286 km,respectively,were obviously deviated from the observations.Simulation results of the near-field stations are larger than the observations at high frequencies(>6 Hz).The discrepancy likely comes from the nonlinear site effect of near-field stations,which reduced the site amplification at high frequencies.Simulation result of the far-field stations is smaller than the observation at frequencies above 1 Hz.As these stations are located close to the Longmenshan Fault Zone(LFZ),thus,we obtained a new quality factor(Q)from data of historical events and stations located around LFZ.Using the new Q value,the discrepancies of the high-frequency simulation results of the far-field stations were corrected.This result indicated that the laterally varying Q values can be used to address the impact of strong crustal lateral heterogeneity on simulation.
基金supported by the“Second Tibetan Plateau Scientific Expedition and Research Program(STEP)”(Grant No.2019QZKK0902)the Strategic Priority Research Program of the CAS(No.XDA23090203)。
文摘At 12:52 pm on September 5,2022,an Ms 6.8 earthquake occurred in Luding County,Sichuan Province,China.Based on high-resolution aerial photographs and satellite imageries obtained after the earthquake,as well as field investigation,a total of 8685 earthquake-triggered landslides(EQTLs)were interpreted.The landslides covered an area of 30.7km^(2),with a source area of 9.4 km^(2).These EQTLs were mainly distributed in areas with a seismic intensity of VIII and IX.Most of the landslides were small and medium in size,and their types included landslide,rockfall,and rock slump.Characteristic landslide distributions were found,EQTLs were distributed along the Xianshuihe fault,landslide area decreased gradually with an increased distance to the fault;EQTLs were distributed along the Daduhe River and roads;besides,landslide distribution was associated with ground deformation caused by the earthquake.EQTLs’characteristics indicated that,a large number of EQTLs were located near the foot of the slope;the full area of EQTLs and their source area followed a power function.This study concluded that Luding EQTLs were greater in number and area but relatively smaller in terms of affected area.Investigations on geo-hazards post-earthquake and risk assessment were proposed in the earthquake-stricken area to support the rehabilitation and reconstruction.
基金support from the National Natural Science Foundation of China(Nos.42104043,42374081,and U2039208)the Fundamental Research Funds for the Institute of Geophysics,China Earthquake Administration(No.DQJB22R35).
文摘On August 6,2023,a magnitude MW5.5 earthquake struck Pingyuan County,Dezhou City,Shandong Province,China.This event was significant as no large earthquakes had been recorded in the region for over a century,and no active fault had been previously identified.This study collects 1309 P-wave arrival times and 866 S-wave arrival times from 74 seismic stations less than 200 km to the epicenter to constrain the spatial distribution of the mainshock and its 125 early aftershocks by the double difference earthquake relocation method,and selects 864 P-waveforms from 288 stations located within 800 km of the epicenter to constrain the focal mechanism solution of the mainshock through centroid moment tensor inversion.The relocation and the inversion indicate,the Pingyuan MW5.5 earthquake was caused by a rupture on a buried fault,likely an extensive segment of the Gaotang fault.This buried fault exhibited a dip of approximately 75°to the northwest,with a strike of 222°,similar to the Gaotang fault.The rupture initiated at the depth of 18.6 km and propagated upward and northeastward.However,the ground surface was not broken.The total duration of the rupture was~6.0 s,releasing the scalar moment of 2.5895×1017 N·m,equivalent to MW5.54.The moment rate reached the maximum only 1.4 seconds after the rupture initiation,and the 90%scalar moment was released in the first 4.6 s.In the first 1.4 seconds of the rupture process,the rupture velocity was estimated to be 2.6 km/s,slower than the local S-wave velocity.As the rupture neared its end,the rupture velocity decreased significantly.This study provides valuable insights into the seismic characteristics of the Pingyuan MW5.5 earthquake,shedding light on the previously unidentified buried fault responsible for the seismic activity in the region.Understanding the behavior of such faults is crucial for assessing seismic hazards and enhancing earthquake preparedness in the future.
文摘The M6.2 earthquake in Jishishan,Gansu Province,on December 18,2023,caused extraordinary earthquake disasters.It was located in the northern part of the north−south seismic zone,which is a key area for earthquake monitoring in China.The newly built dense strong motion stations in this area provide unprecedented conditions for high-precision earthquake relocation,especially the earthquake focal depth.This paper uses the newly built strong motion and traditional broadband seismic networks to relocate the source locations of the M3.0 and above aftershocks and to invert their focal mechanisms.The horizontal error of earthquake location is estimated to be 0.5−1 km,and the vertical error is 1−2 km.The focal depth range of aftershocks is 9.6−14.6 km,distributed in a 12-km-long strip with SSE direction.Aftershocks in the south are more concentrated horizontally and vertically,while aftershocks in the north are more scattered.The focal mechanisms of the main shock and aftershocks are relatively consistent,and the P-axis orientation is consistent with the regional strain direction.There is a seismic blank area of M3.0 and above,about 3−5 km between the main shock and aftershocks.It is suggested that the energy released by the main shock rupture is concentrated in this area.Based on the earthquake location and focal mechanism of the main shock,it is inferred that the Northern Lajishan fault zone is the seismogenic structure of the main shock,and the main shock did not occur on the main fault,but on a secondary fault.The initial rupture depth and centroid depth of the main shock were 12.8 and 14.0 km,respectively.The source rupture depth may not be the main reason for the severe earthquake disaster.
基金supported by the National Natural Science Foundation of China (51408086)the Opening Fund of the State Key Laboratory of Geohazard Prevention and GeoenvironmentalProtection (Chengdu University of Technology) (SKLGP2015Z001)
文摘In order to investigate the role of the amplification of peak ground acceleration(PGA) in seismic landslide formation mechanisms and study how earthquake waves interact with rock structures, a few strong-motion seismometers are installed at various locations on both sides of the Lengzhuguan gully. Five strong-motion seismometers were triggered at different depths in a tunnel at the same altitude during the Kangding Ms 5.8 earthquake on November 25 th, 2014. The data reveal that the horizontal peak acceleration(PGA_H) at each site decreased with increasing site depths. The PGAH at the deepest monitoring site(99 m from the tunnel entrance) was approximately half that of the outermost site. The amplitude of the acceleration response spectrum was also attenuated from the entrance inwards, the dynamic magnification factor(β) of the standard acceleration spectrum was less than 3.5, and rate of change was the same as that for the amplitude acceleration response. The Fourier spectra of each monitoring site also decreased from the outside inwards, and the components of the Fourier spectra were more complex at the surface.