Microstructure and mechanical properties of isothermal multi-axial forging formed AZ61 Mg alloy

Microstructure and mechanical properties of AZ61 Mg alloy during isothermal multi-axial forging （MAF） were studied. The mechanisms of grain refinement and relationship between the microstructures and mechanical properties were discussed. The results show that the average grain size decreases with increasing the number of MAF passes. The grains are significantly refined at the 1st and 2nd MAF passes, and gradually refined at higher MAF passes. The initial grain size of 148 lam decreases to about 14 gm after 6 MAF passes. The grain refinement occurs mainly by continuous dynamic recrystallization. With increasing the MAF passes, both the tensile strength and the elongation to failure of the alloy are significantly enhanced.

Dynamic precipitation during multi-axial forging of an Mg-7Gd-5Y-1Nd-0.5Zr alloy

The dynamic precipitation behavior during multi-axial forging in an Mg-7Gd-5Y-1Nd-0.5Zr alloy has been investigated and compared with that in static precipitation treatment. The results indicated that dynamic precipitation does occur during multi-axial forging. The dynamic precipitate can be deduced as β phase with face-centered cubic crystal structure (a = 2.22 nm). Most of the β precipitates locate at the dynamic recrystallization grain boundaries. The morphology and orientation relationship is different from that of the β phase formed in the static precipitation treated alloys, although the crystal structure is the same. The precipitation temperature of β phase during MAF is higher than that in the static precipitation treatment.

Multi-axial strain-stiffening elastic potentials with energy bounds:explicit approach based on uniaxial data

According to the well-known models for rubberlike elasticity with strain- stii^ening effects, the unbounded strain energy is generated with the unlimitedly growing stress when the stretch approaches certain limits. Toward a solution to this issue, an explicit approach is proposed to derive the multi-axial elastic potentials directly from the uniaxial potentials. Then, a new multi-axial potential is presented to characterize the strain-stiffening effect by prescribing suitable forms of uniaxia] potentials so that the strain energy is always bounded as the stress grows to infinity. Numerical examples show good agreement with a number of test data.

Three-dimensional Tool Radius Compensation for Multi-axis Peripheral Milling

Few function about 3D tool radius compensation is applied to generating executable motion control commands in the existing computer numerical control (CNC) systems. Once the tool radius is changed, especially in the case of tool size changing with tool wear in machining, a new NC program has to be recreated. A generic 3D tool radius compensation method for multi-axis peripheral milling in CNC systems is presented. The offset path is calculated by offsetting the tool path along the direction of the offset vector with a given distance. The offset vector is perpendicular to both the tangent vector of the tool path and the orientation vector of the tool axis relative to the workpiece. The orientation vector equations of the tool axis relative to the workpiece are obtained through homogeneous coordinate transformation matrix and forward kinematics of generalized kinematics model of multi-axis machine tools. To avoid cutting into the corner formed by the two adjacent tool paths, the coordinates of offset path at the intersection point have been calculated according to the transition type that is determined by the angle between the two tool path tangent vectors at the corner. Through the verification by the solid cutting simulation software VERICUTwith different tool radiuses on a table-tilting type five-axis machine tool, and by the real machining experiment of machining a soup spoon on a five-axis machine tool with the developed CNC system, the effectiveness of the proposed 3D tool radius compensation method is confirmed. The proposed compensation method can be suitable for all kinds of threeto five-axis machine tools as a general form.

Anisotropic Force Ellipsoid Based Multi-axis Motion Optimization of Machine Tools

The existing research of the motion optimization of multi-axis machine tools is mainly based on geometric and kinematic constraints, which aim at obtaining minimum-time trajectories and finding obstacle-free paths. In motion optimization, the stiffness characteristics of the whole machining system, including machine tool and cutter, are not considered. The paper presents a new method to establish a general stiffness model of multi-axis machining system. An analytical stiffness model is established by Jacobi and point transformation matrix method. Based on the stiffness model, feed-direction stiffness index is calculated by the intersection of force ellipsoid and the cutting feed direction at the cutter tip. The stiffness index can help analyze the stiffness performance of the whole machining system in the available workspace. Based on the analysis of the stiffness performance, multi-axis motion optimization along tool paths is accomplished by mixed programming using Matlab and Visual C＋＋. The effectiveness of the motion optimization method is verified by the experimental research about the machining performance of a 7-axis 5-linkage machine tool. The proposed research showed that machining stability and production efficiency can be improved by multi-axis motion optimization based on the anisotropic force ellipsoid of the whole machining system.

The development of real time data driving multi-axis linkage and synergic movement control system of 3D variable cross-section roll forming machine

The three dimensional variable cross-section roll forming is a kind of new metal forming technol- ogy which combines large forming force, multi-axis linkage movement and space synergic movement, and the sequential synergic movement of the ganged roller group is used to complete the metal sheet forming according to the shape of the complicated and variable forming part data. The control system should meet the demands of quick response to the test requirements of the product part. A new kind of real time data driving multi-axis linkage and synergic movement control strategy of 3D roll forming is put forward in the paper. In the new control strategy, the forming data are automatically generated according to the shape of the parts, and the multi-axis linkage movement together with cooperative motion among the six stands of the 3D roll forming machine is driven by the real-time information, and the control nodes are also driven by the forming data. The new control strategy is applied to a 48 axis 3D roll forming machine developed by our research center, and the control servo period is less than 10ms. A forming experiment of variable cross section part is carried out, and the forming preci- sion is better than ＋ 0.5mm by the control strategy. The result of the experiment proves that the control strategy has significant potentiality for the development of 3D roll forming production line with large scale, multi-axis ganged and svner^ic movement

Design of a Multi-axis Motion Control Platform Based on LabVIEW’s Fuzzy Control Algorithm

This paper presents a fuzzy control algorithm applied to the position control of a multi-axis motion platform to achieve high precision motion control of the multi-axis motion platform.A LabVIEW-based multi-axis motion control system is designed.This system controls stepper motors using trapezoidal acceleration/deceleration pulse types and fuzzy control algorithms,which effectively avoids mechanical jitter and loss of step in the process of multi-angle motion of the stepper motor,and achieves accurate control of the stepper motor.The TCP/IP(transmission control protocol/internet protocol)communication protocol is used,so that data are output stably and not lost in the process of transmission and communication,achieving the purpose of interconnection of different systems and remote control of equipment.This control system has been tested to maintain a high level of stability and repeatability during actual operation.

Laser Interferometer Based Measurement for Positioning Error Compensation in Cartesian Multi-Axis Systems

Accuracy is one of the most important key indices to evaluate multi-axis systems’ (MAS’s) characteristics and performances. The accuracy of MAS’s such as machine tools, measuring machines and robots is adversely affected by various error sources, including geometric imperfections, thermal deformations, load effects, and dynamic disturbances. The increasing demand for higher dimensional accuracy in various industrial applications has created the need to develop cost-effective methods for enhancing the overall performance of these mechanisms. Improving the accuracy of a MAS by upgrading the physical structure would lead to an exponential increase in manufacturing costs without totally eliminating geometrical deviations and thermal deformations of MAS components. Hence, the idea of reducing MAS’s error by a software-based alternative approach to provide real-time prediction and correction of geometric and thermally induced errors is considered a strategic step toward achieving the full potential of the MAS. This paper presents a structured approach designed to improve the accuracy of Cartesian MAS’s through software error compensation. Four steps are required to develop and implement this approach: (i) measurement of error components using a multidimensional laser interferometer system, (ii) tridimensional volumetric error mapping using rigid body kinematics, (iii) volumetric error prediction via an artificial neural network model, and finally (iv) implementation of the on-line error compensation. An illustrative example using a bridge type coordinate measuring machine is presented.

DEVELOPMENT OF NEW GENERATION THERMOMECHANICAL SIMULATOR-MULTI-AXIS RESTRAINT COMPRESSION(MARC-STRAIN^(TM))SYSTEM

Ultrafine grain size is often achieved by severe plastic deformation. A few techniques have been devel- oped to achieve severe plastic deformation,such as equal channel angular (ECA ) processing, torsion, and accumulative roll bonding (ARB) techmpues. This paper will introduce a moftiaxis deformation technique which can achieve essentially unlimited strain with constant deformation volume. The mul- tiaxis deformation can be fully restrained or unrestrained.The bulk volume of a multiaxis restraint compression specimen can be easily machined into mechanical testing specimens for mechanical property measurement and other studies.

Multi-Excitation Fatigue Testing for Large Full-Scale Wind Turbine Blade

In order to solve the problem of insufficient exciting force of equipment for large full-scale wind turbine blade fatigue testing,the influence of gravity on the performance of excitation equipment and fatigue damage evaluation of the different positions of wind turbine blades are analyzed.With the multi-excitation loading in the horizontal direction,the actuator force of the excitation equipment does not need to overcome the gravity of the dynamic mass,which directly outputs the exciting force of the system vibration.The excitation efficiency of the equipment is 77%higher than that of the vertical load.The gravity moment of the horizontal loading mode is perpendicular to the loading direction.That is,the mean load in the flapwise direction is zero.The weight of excitation equipment could replace the tuning mass on the condition that the self-weight of equipment is reduced by the multi-excitation mode,which helps the excitation equipment play the comprehensive function of excitation equipment and tuning mass.At the same time,the gravity moment in the edgewise direction will be decreased by 17.0%22.5%under the multi-excitation horizontal loading mode.In the vertical loading mode,the gravity moment is the mean load,which only increases fatigue damage accumulation by 15.6%.By comparing the role of gravity in the excitation equipment and fatigue damage evaluation,the multi-excitation horizontal loading mode has more advantage to performance the exciting force than the contribution of gravity to the fatigue damage accumulation in the vertical loading mode.Through the fatigue testing of multi-excitation horizontal loading,the potential of excitation equipment is explored,and the problem of insufficient exciting force in large full-scale wind turbine blade fatigue testing will be solved.

Observation of tropospheric NO_2 by airborne multi-axis differential optical absorption spectroscopy in the Pearl River Delta region,south China

An airborne multi-axis differential optical absorption spectroscopic （AMAX-DOAS） instrument was developed and applied to measure tropospheric NO2 in the Pearl River Delta region in the south of China. By combining the measurements in nadir and zenith directions and analyzing the UV and visible spectral region using the DOAS method, information about tropospheric NO2 vertical columns was obtained. Strong tropospheric NO2 signals were detected when flying over heavilly polluted regions and point sources like plants. The AMAX-DOAS results were compared with ground-based MAX-DOAS observations in the southwest of Zhuhai city using the same parameters for radiative transport calculations. The difference in vertical column data between the two instruments is about 8%. Our data were also compared with those from OMI and fair agreement was obtained with a correlation coefficient R of 0.61. The difference between the two instruments can be attributed to the different spatial resolution and the temporal mismatch during the measurements.

Research on Contour Error Based on CNC Multi-axis Motion Control System

The contour error was analyzed based on CNC multi-axis motion control, the contour error model was obtained focused on beeline and different radius of curvature and common contour of curve, for a CNC biaxial motion control system and the mechanism of producing contour error and the relationship between tracking error and contour error were presented. The theoretical and practical significance of modeling error and controlling error in motion control systems was carried out.

Fine-Grained Action Recognition Based on Temporal Pyramid Excitation Network

Mining more discriminative temporal features to enrich temporal context representation is considered the key to fine-grained action recog-nition.Previous action recognition methods utilize a fixed spatiotemporal window to learn local video representation.However,these methods failed to capture complex motion patterns due to their limited receptive field.To solve the above problems,this paper proposes a lightweight Temporal Pyramid Excitation(TPE)module to capture the short,medium,and long-term temporal context.In this method,Temporal Pyramid(TP)module can effectively expand the temporal receptive field of the network by using the multi-temporal kernel decomposition without significantly increasing the computational cost.In addition,the Multi Excitation module can emphasize temporal importance to enhance the temporal feature representation learning.TPE can be integrated into ResNet50,and building a compact video learning framework-TPENet.Extensive validation experiments on several challenging benchmark(Something-Something V1,Something-Something V2,UCF-101,and HMDB51)datasets demonstrate that our method achieves a preferable balance between computation and accuracy.

A study on the application of diffuse axonal multi-axis general evaluation for braininjury assessment in small overlap barrier crash test

Purpose:Head injury criterion(HIC)companied by a rotation-based metric was widely believed to behelpful for head injury prediction in road traffic accidents.Recently,the Euro-New Car AssessmentProgram utilized a newly developed metric called diffuse axonal multi-axis general evaluation(DAMAGE)to explain test device for human occupant restraint(THOR)head injury,which demonstratedexcellent ability in capturing concussions and diffuse axonal injuries.However,there is still a lack ofcomprehensive understanding regarding the effectiveness of using DAMAGE for Hybrid III 50thpercentile male dummy(H50th)head injury assessment.The objective of this study is to determinewhether the DAMAGE could capture the risk of H50th brain injury during small overlap barrier tests.Methods:To achieve this objective,a total of 24 vehicle crash loading curves were collected as input datafor the multi-body simulation.Two commercially available mathematical dynamic models,namelyH50th and THOR,were utilized to investigate the differences in head injury response.Subsequently,adecision method known as simple additive weighting was employed to establish a comprehensive braininjury metric by incorporating the weighted HIC and either DAMAGE or brain injury criterion.Furthermore,35 sets of vehicle crash test data were used to analyze these brain injury metrics.Results:The rotational displacement of the THOR head is significantly greater than that of the H50thhead.The maximum linear and rotational head accelerations experienced by H50th and THOR modelswere(544.6±341.7)m/s^(2),(2468.2±1309.4)rad/s^(2) and(715.2±332.8)m/s^(2),(3778.7±1660.6)rad/s^(2),respectively.Under the same loading condition during small overlap barrier(SOB)tests,THOR exhibits ahigher risk of head injury compared to the H50th model.It was observed that the overall head injuryresponse during the small overlap left test condition is greater than that during the small overlap righttest.Additionally,an equation was formulated to establish the necessary relationship between theDAMAGE values of THOR and H50th.Conclusion:If H50th rather than THOR is employed as an evaluation tool in SOB crash tests,newlydesigned vehicles are more likely to achieve superior performance scores.According to the current injurycurve for DAMAGE and brain injury criterion,it is highly recommended that HIC along with DAMAGE wasprioritized for brain injury assessment in SOB tests.

串并联机器人控制HIFU的插补算法的研究

针对高强度聚焦超声串并联机器人的硬件结构特点,插补算法采取了粗插补和精插补相结合的两级模式。为满足电机轴动态性能限制条件,同时采用了插补前加减速和插补后加减速的方法,并给出了插补算法的具体实现步骤。

基于可编程多轴控制器的红外传感器片上测试系统设计

探针测试台是一种传统半导体工艺中间测试设备,用于在硅片划片前测试电子器件性能、良率,并给出其在晶圆上分布的映射图表。目前国内外自动或半自动探针测试台都是针对传统IC电路设计,采用封闭式结构,无法根据传感器多变的特性、复杂的测试环境需求完成对器件的片上测试。采用美国Delta Tau公司推出的PMAC可编程多轴运动控制器作为核心控制系统,构建了一套针对红外热电堆器件特殊测试需求的批量化片上测试系统。该测试系统具有响应速度快、控制精度高、可扩展性强的特性,不仅可满足红外热电堆器件的片上批量化测试需求,还可通过定制性的模块删减以满足不同传感器的片上测试。

Path Planning of Multi-Axis Robotic Arm Based on Improved RRT*

An improved RRT∗algorithm,referred to as the AGP-RRT∗algorithm,is proposed to address the problems of poor directionality,long generated paths,and slow convergence speed in multi-axis robotic arm path planning.First,an adaptive biased probabilistic sampling strategy is adopted to dynamically adjust the target deviation threshold and optimize the selection of random sampling points and the direction of generating new nodes in order to reduce the search space and improve the search efficiency.Second,a gravitationally adjustable step size strategy is used to guide the search process and dynamically adjust the step-size to accelerate the search speed of the algorithm.Finally,the planning path is processed by pruning,removing redundant points and path smoothing fitting using cubic B-spline curves to improve the flexibility of the robotic arm.Through the six-axis robotic arm path planning simulation experiments on the MATLAB platform,the results show that the AGP-RRT∗algorithm reduces 87.34%in terms of the average running time and 40.39%in terms of the average path cost;Meanwhile,under two sets of complex environments A and B,the average running time of the AGP-RRT∗algorithm is shortened by 94.56%vs.95.37%,and the average path cost is reduced by 55.28%vs.47.82%,which proves the effectiveness of the AGP-RRT∗algorithm in improving the efficiency of multi-axis robotic arm path planning.

MODELING AND COMPENSATION TECHNIQUE FOR THE GEOMETRIC ERRORS OF FIVE-AXIS CNC MACHINE TOOLS

One of the important trends in precision machining is the development ofreal-time error compensation technique. The error compensation for multi-axis CNC machine tools isvery difficult and attractive. The modeling for the geometric error of five-axis CNC machine toolsbased on multi-body systems is proposed. And the key technique of the compensation―identifyinggeometric error parameters―is developed. The simulation of cutting workpiece to verify the modelingbased on the multi-body systems is also considered.

ROBOT'S MOTION ERROR AND ONLINE COMPENSATION BASED ON FORCE SENSOR

Robot＇s dynamic motion error and on-line compensation based on multi-axis force sensor are dealt with.It is revealed that the reasons of the error are formed and the relations of the error are delivered.A motion equation of robot＇s termination with the error is established,and then,an error matrix and an error compensation matrix of the motion equation are also defined.An on-line error＇s compensation method is put forward to decrease the displacement error,which is a degree of millimeter,shown by the result of simulation of PUMA562 robot.

Vertical profile of aerosol extinction based on the measurement of O4 of multi-elevation angles with MAX-DOAS

A method for aerosol extinction profile retrieval using ground-based multi-axis differential optical absorption spectroscopy(MAX-DOAS)is studied,which is based on a look-up table algorithm.The algorithm uses parametric method to represent aerosol extinction profiles and simulate different atmospheric aerosol states through atmospheric radiation transfer model.Based on the method,aerosol extinction profile was obtained during six cloud-free days.The O4 differential air mass factor(dAMF)measured by MAX-DOAS is compared with the corresponding model results under different atmospheric conditions(R^2=0.78).The aerosol optical thickness,aerosol weight factor in boundary layer,and the height of the boundary layer are obtained after the process of minimization and look-up table method.The retrieved aerosol extinction in boundary layer is compared with PM2.5 data measured by ground point instrument.The diurnal variation trends of the two methods are in good agreement.The correlation coefficients of the two methods are 0.71 when the aerosol optical thickness is smaller than 0.5.The results show that the look-up table method can obtain the aerosol state of the troposphere and provide validation for other instrument data.