Effect of Oxygen on Surface Properties and Drug Release Behavior of Plasma Polymer of n-Butyl Methacrylate

The effects of oxygen on the chemical structure, morphology, hydrophilicity and drug release behavior of radio-frequency plasma poly n- butyl methacrylate （PPBMA） thin film were carded out for the first time. ATR-FTIR and XPS showed that oxygen had little influence on the chemical structure and composition of PPBMAs, which did not agree with the thought that the presence of oxygen gas would increase the oxidized carbon functionalities in the plasma polymer. SEM and static contact angle measurement indicated that in case of deposition with oxygen, the smoothness and hydrophilicity of PPBMA were dramatically improved. The drug release behavior showed that drug release from the PPBMA coating without oxygen was biphasic patterns, while from PPBMA coating with oxygen was Higuchi release. These results were helpful for the design and tailoring of the PPBMA polymer film and other of plasma polymers film, but could provide a new idea for the drug release controlled form.

Controlled Radical Photopolymerization of n-Butyl Methacrylate in Bluk Mediated by HTEMPO

Controlled radical photopolymerization of n-butyl methacrylate（n-BMA） mediated by 4-hydroxy-2,2,6,6-tetramethyl-1-piperidinyloxy（HTEMPO） was carried out in bulk at ambient temperature. It was found that obtained n-BMA homopolymers exhibited narrow polydispersities of around 1.4, which was characterized by GPC. Plots of number-average molecular weight vs. conversion and Ln（[Mo]/[M]） vs. time were liner respectively, indicating that was a controlled photopolymerization.

INVESTIGATION OF THE ATRP OF n-BUTYL METHACRYLATE USING THE Cu(I)/N,N,N',N",N"-PENTAMETHYLDIETHYLENETRIAMINE CATALYST SYSTEM

The polymerization of n-butyl methacrylate was investigated using the Atom Transfer Radical Polymerization technique with CuBr and CuCl/N,N,N',N',N'-pentamethyldiethylenetriamine catalytic systems. Various combinations of catalyst systems and initiators were utilized in order to optimize the polymerization conditions and to obtain well-defined polymers (i.e. controlled molecular weights and low polydispersities). It has been found that the optimal initiator for this system is a chlorine-based initiator, when the catalyst used is a salt in conjunction with the N,N,N',N',N'- pentamethyldiethylenetriamine ligand. Bromine-based initiators tend to result in large amounts of initial termination, leading to polymers with less than ideal chain end functionality, even if CuCl is used as the species to invoke the halogen exchange. Additionally, the effects of the polymerization temperature, species and the initiator structure were determined.

Preparation and Alkylation of Carbon Nanofibers from Polymethyl Methacrylate

Carbon nanofibers have revolutionized nanotechnology due to their potential applications in emerging frontiers of research and industrial sectors. This can be attributed to their superior properties such as higher mechanical strength, unique surface characteristics, and improved adherence that is transmitted into the polymer matrix to form a nanocomposite with improved properties. Polymethyl methacrylate is a common carbon source for the synthesis of carbon nanofibres of its high mechanical strength, thermal stability, and low moisture and water absorbing capacity that allows its products to have several applications. In this work, we report the successful electrospinning of carbon nanofibres from Poly methyl methacrylate and functionalizing the resulting carbon nanofibres. The functionalized carbon nanofibres were analyzed to determine their solubility/dispersion in selected organic solvents, then characterized using Fourier transform infra-red spectroscopy, Raman spectroscopy, scanning electron microscopy combined with Energy dispersive spectroscopy and Thermalgravimetric analysis.

Synthesis and Characterization of Poly Styrene-Co-Poly 2-Hydroxyethylmethacrylate (HEMA) Copolymer and an Investigation of Free-Radical Copolymerization Propagation Kinetics by Solvent Effects

A series of homo and copolymers of styrene (ST) and 2-hydroxyethyl methacrylate (HEMA) in three different media (bulk, tetrahydrofuran, and benzene) have been investigated by free radical polymerization method. The samples obtained from the synthesis were characterized by Fourier Transform-Infrared spectroscopy (FT-IR), proton nuclear magnetic resonance spectroscopy (1H NMR), atomic force microscopy (AFM), and differential scanning calorimetry (DSC). The results show that the synthesis of the polymers is more feasible under neat conditions rather than solvent directed reaction. Moreover, the DSC data shows that the polystyrene obtained is amorphous in nature and therefore displayed only a glass transition signal rather than crystallization and melting peaks. In addition, this study indicates that homolopolymerization of styrene via free radical polymerization tends to be preferable in less polar solvents like THF than in non-polar solvents like benzene. Benzene might destabilize the formation of the reactive radicals leading to the formation of the products. In summary, the homolpolymerization of styrene is more feasible than the homopolymerization 2-hydroxyethyl methacrylate under the experimental setup used. Styrene is more reactive than 2-hydroxyethyl methacrylate than free radical polymerization reaction due in part of the generation of the benzylic radical intermediate which is more stable leading to the formation of products than alkyl radical which are less stable. Furthermore, polymerization of styrene under neat conditions is preferable in solvent-assisted environments. The choice of solvent for the synthesis of these polymers is crucial and therefore the selection of solvent that leads to the formation of a more stable reaction intermediate is more favorable. It is worth noting that the structure of the proposed copolymer consists of a highly polar and hydrophilic monomer, 2-hydroxyethyl methacrylate and a highly non-polar and hydrophobic monomer, styrene. These functionalities constitute an amphiphilic copolymer with diverse characteristics. A plausible explanation underlying our observations is that the reaction conditions employed in the synthesis of these copolymers might not be the right route required under free radical polymerization.

EFFECTS OF ω-ACRYLOYL POLY (ETHYLENE OXIDE) MACROMONOMER ON EMULSIFIER-FREE EMULSI0N COPOLYMERIZATION OF METHYL METHACRYLATE AND n-BUTYL ACRYLATE

Well-defined nonionic hydrophilic ω-acryloyl poly(ethylene oxide) macro-monomer (PEO-A) has been prepared by living anionic polymerization of ethylene oxidewith diphenyl methyl potassium as the initiator and acryloyl chloride as the reaction termi-nating agent. The polymer was characterized by FTIR and SEC. The emulsifier-free emul-sion polymerization of methyl methacrylate (MMA) and n-butyl acrylate (BA) containingvarious concentrations of PEO-A was studied. In all cases stable emulsion coplymerizationsof MMA and BA were obtained. The stabilizing effect was found to be dependent on themolecular weight and the feed amount of the macromonomer.

Synthesis,Characterization and Catalytic Application of H_3PW_(12)O_(40)/MCM-48 in the Esterification of Methacrylic Acid with n-butyl Alcohol

A novel environmental friendly catalyst, H3PW12O40/MCM-48, was prepared by impregnation method. The catalysts were characterized by means of XRD and FT-IR. The synthesis of n-butyl methacrylate catalyzed by H3PW12O40/MCM-48 was studied with methacrylic acid and n-butyl alcohol as reactants. H3PW12O40/MCM-48 is an excellent catalyst for synthesizing n-butyl methacrylate and Keggin structure of H3PW12O40 kept unchanged after being impregnated on surface of the molecular sieve support. Effects of n（methacrylic acid）：n（n-butyl alcohol）, catalyst dosage, cyclohexane（water-stripped reagent） and reaction time on yields of the product were investigated. The optimum conditions have been found, that is, molar ratio of acid to alcohol is 1：1.6, mass ratio of catalyst used to the reactants is 0.5% and reaction time is 2.0 h. Under these conditions, the yield of n-butyl methacrylate can reach 93.7%.

Synthesis, characterization and catalytic application of H4SiW12O40/MCM-48 in the esterification of methacrylic acid with n-butyl alcohol

A novel environmental friendly catalyst, H4SiW12O40/MCM-48, was prepared by impregnation method. The catalysts were characterized by means of XRD and FT-IR. The synthesis of n-butyl methacrylate catalyzed by H4SiW12O40/MCM-48 was studied with methacrylic acid and n-butyl alcohol as reactants. H4SiW12O40/MCM-48 was an excellent catalyst for the synthesis of n-butyl methacrylate and Keggin structure ofH4SiW12O40 kept unchanged after impregnated on surface of the molecular sieve support. Effects of n（methacrylic acid）： n（n-butyl alcohol）, catalyst dosage, cyclohexane （water-stripped reagent） and reaction time on the yields of the product were investigated. The optimum conditions have been found, that is, molar ratio of acid to alcohol is 1：1.5, mass ratio of catalyst used to the reactant is 1.5%, cyclohexane is 10 mL and reaction time is 1.5h. Under these conditions, the yield of n-butyl methacrylate can reach 73.2%.

DESIGN AND SYNTHESIS OF NOVEL CHIRAL IONIC LIQUIDS AND THEIR APPLICATION IN FREE RADICAL POLYMERIZATION OF METHYL METHACRYLATE

Two new chiral ionic liquids, 1 -((-)-menthoxycarbonylmethylene)-3-methylimidazolium hexafluorophosphateand 1-((-)-menthoxycarbonylmethylene)-3-hexadecylimidazolium hexafluorophosphate, were designed an d prepared. Theirchemical structures were characterized by ~1H-NMR. Reverse atom transfer radical polymerization of methyl methacrylate(MMA) in these two ionic liquids was carried out using AIBN/CuCl_2/bipy as the initiating system. The resultant well-definedpolymethyl methacrylate (PMMA) was employed as a macroinitiator to induce the atom transfer radical polymerization ofmenthyl methacrylate (MnMA) in chlorobenzene, which yielded a PMMA-b-PMnMA diblock copolymer with narrow polydispersity.

Polybutylacrylate/poly(methyl methacrylate) Core-Shell Elastic Particles as Epoxy Resin Toughener: Part I Design and Preparation

Polybutylacrylate (PBA)/poly(methyl methacrylate) (PMMA) core-shell elastic particles (CSEP), whose rubbery core diameter ranged from 0.08 μm to 1.38μm, were synthesized by using conventional emulsion polymerization, multi-step emulsion polymerization, and soapless polymerization. Allyl methacylate (ALMA) and ethylene glycol dimethacrylate (EGDMA) were selected as crosslinking reagents for core polymerization. Methacrylic acid (MAA) was used as functional co-monomer with methyl methacrylate as shell component. The content of vinyl groups in PBA rubbery core increased with the amount of crosslinking reagents. The core-shell ratio affected great on the morphology of the complex particles. Furthermore, the amounts of carboxyl on the surface of core-shell particles, copolymerized with acrylic acid, were determined by potentiometric titration. Results showed that methylacrylic acid was distributed mostly on the surface of particles.

MgO–SBA-15 Supported Pd–Pb Catalysts for Oxidative Esterification of Methacrolein with Methanol to Methyl Methacrylate

Novel Mg O–SBA-15 supported catalysts were prepared for oxidative esterification of methacrolein(MAL) with methanol to methyl methacrylate(MMA). The Mg O–SBA-15 supports were synthesized with different magnesia loadings from different magnesium precursors and hydrochloric acid molar concentrations. The Mg O–SBA-15 supports and Pd–Pb/Mg O–SBA-15 catalysts were characterized by several analysis methods. The results revealed that the addition of Mg O improved the ordered structure of SBA-15 supports and provided surface alkalinity of SBA-15 supports. The average size of the Pd3 Pb particles on magnesia-modified Pd–Pb/Mg O–SBA-15 catalysts was smaller than that on the pure silica-based Pd–Pb/SBA-15 catalysts. The experiments on catalyst performance showed that the magnesia-modified Pd–Pb/Mg O–SBA-15 catalysts had higher activity than pure silica-based Pd–Pb/SBA-15 catalysts, showing the strong dependence of catalytic activity on the average size of active particles. The difference of activity between Pd–Pb/SBA-15 catalysts and Pd–Pb/Mg O–SBA-15 catalysts was due to the discrepant structural properties and surface alkalinity provided by Mg O, which led to the different Pd3 Pb particle sizes and then resulted in the different number of active sites. Besides magnesia loadings, other factors, such as hydrochloric acid molar concentration and magnesium precursors, had considerable influences on the catalytic activity.

Novel ionic liquids as reaction medium for atom transfer radical polymerization of methyl methacrylate

Atom transfer radical polymerization （ATRP） of methyl methacrylate （MMA） employing ethyl 2-bromoisobutyrate （EBiB）/ CuBr as the initiating system was investigated at 50 ℃ in the absence of any additional ligand in the three room temperature ionic liquids （RTILs）, 1-methyl-imidazolium acetate （[mim][CH3COO]）, 1-methylimidazolium propionate （[mim][CH3CH2COO]） and 1-methylimidazolium butyrate （[mim][CH3CH2CH2COO]）, respectively. All the polymerization in the three RTILs proceeded in a well-controlled manner. The sequence of the apparent polymerization rate constants was kapp（[mim][CH3COO]） 〉 kapp（[mim] [CH3CH2COO]） 〉 kapp （[mim][CH3CH2CH2COO]）.

Evaluation of three-dimensional biofilms on antibacterial bonding agents containing novel quaternary ammonium methacrylates

Antibacterial adhesives are promising to inhibit biofilms and secondary caries. The objectives of this study were to synthesize and incorporate quaternary ammonium methacrylates into adhesives, and investigate the alkyl chain length effects on three-dimensional biofilms adherent on adhesives for the first time. Six quaternary ammonium methacrylates with chain lengths of 3, 6, 9, 12, 16 and 18 were synthesized and incorporated into Scotchbond Multi-Purpose. Streptococcus mutans bacteria were cultured on resin to form biofilms. Confocal laser scanning microscopy was used to measure biofilm thickness, live/dead volumes and live-bacteria percentage vs. distance from resin surface. Biofilm thickness was the greatest for Scotchbond control; it decreased with increasing chain length, reaching a minimum at chain length 16. Live-biofilm volume had a similar trend. Dead-biofilm volume increased with increasing chain length. The adhesive with chain length 9 had 37% live bacteria near resin surface, but close to 100% live bacteria in the biofilm top section. For chain length 16, there were nearly 0% live bacteria throughout the three-dimensional biofilm. In conclusion, strong antibacterial activity was achieved by adding quaternary ammonium into adhesive, with biofilm thickness and live-biofilm volume decreasing as chain length was increased from 3 to 16. Antibacterial adhesives typically only inhibited bacteria close to its surface; however, adhesive with chain length 16 had mostly dead bacteria in the entire three-dimensional biofilm. Antibacterial adhesive with chain length 16 is promising to inhibit biofilms at the margins and combat secondary caries.

MONOMER REACTIVITY RATIO AND THERMAL PERFORMANCE OFα-METHYL STYRENE AND GLYCIDYL METHACRYLATE COPOLYMERS

Synthesis and characterization of the copolymers （PAG） of α-methyl styrene （AMS） and glycidyl methacrylate （GMA） are presented. The copolymers of PAG were characterized by gel permeation chromatography （GPC）, Fourier transform infrared spectroscopy （FTIR）, nuclear magnetic resonance （^1H-NMR） and thermogravimetery （TG）. Based on the copolymer compositions determined by ^1H-NMR, the reactivity ratios of AMS and GMA were found to be 0.105 ± 0.012 and 0.883 ± 0.046 respectively by Kelen-Tudos method. TG revealed that thermal stability of the copolymers decreased with increasing the AMS content in the copolymers, which indicated that the degradation was mainly caused by the chain scission of AMS-containing structures. Under heating, the copolymers depolymerize at their weak bonds and form chain radicals, which could further initiate other chemical reactions.

Genotoxic and Nongenotoxic Effects of Glycidyl Methacrylate on Human Lung Fibroblast Cells

Objective To evaluate the genotoxic and nongenotoxic effects of short-term exposure to glycidyl mathacrylate (GMA) on human lung fibroblast cells (2BS cells) in vitro. Methods DNA strand breakage was determined by single cell gel electrophoresis, and DNA ladder formation assay and flow cytometric analysis were carried out to detect apoptic responses of cells to GMA exposure. The HPRT gene mutation assay was used to evaluate the mutagenicity, and the effect of GMA on gap junctional intercellular communication (GJIC) in the exposed cells was examined with the scrape loading/dye transfer technique. The ability of GMA to transform 2BS cells was also tested by an in vitro cell transformation assay. Results Exposure to GMA resulted in a dose-dependent increase in DNA strand breaks but not apoptic responses. GMA was also shown to significantly induce HPRT gene mutations and morphological transformation in 2BS cells in vitro. In contrast, GMA produced a concentration-dependent inhibition of GJIC. Conclusions GMA elicits both genotoxic and nongenotoxic effects on 2BS cells in vitro. The induction of DNA damage and gene mutations and inhibition of GJIC by GMA may casually contribute to GMA-induced cell transformation.

The Intermetallic Catalysts for Oxidative Esterification of Methacrolein to Methyl Methacrylate

A series of supported intermetallic Pb-Pb catalysts were prepared with the impregnation method by changing the support(silica,molecular sieve or γ-alumina)and the pore size.The chemical states of the two metals were characterized by XPS analysis,the process for producing methyl methacrylate based on the direct oxidative esterification of methacrolein with methanol in the presence of oxygen was performed in a slurry reactor with the above-mentioned catalysts.The influence of the calcination temperature and the kinds of support as well as the pore size on catalytic activity had been extensively investigated.Under the conditions of temperature at 80℃,catalyst 3.8%(ω)and the reaction time 2 h,the conversion rate of methacrolein reached 85%,the selectivity and the yield of methyl methacrylate were 90% and 76.5%,respectively.

SYNTHETIC STUDIES ON BLOOD COMPATIBLE BIOMATERIALSⅡ. SYNTHESIS OF POLY(ETHYLENEGLYCOL MONOMETHYLLTHER ) METHACRYLATE AND ANTITHROMBOGENICITY OF ITS COPOLYMERS

Poly （ethyleneglycol monomethylether） methacrylate （PEGMM）was synthesized by means of the reaction of methacrylyl chloride with sodium monomethylpolyethyleneglycoxide and was characterized by FTIR,;H-NMR,and ultraviolet spectrometries. A series of poly （vinyl alcohol）-graft-PEGMM （PVA-g-PEGMM ）and methyl methacrylate-PEGMM copolymer （PMMA-PEGMM） were prepared and tested for antithrombogenicity in vitro. The results indicate that the antithrombogenicity of the copolymers basically increases with the increasing of the DP of polyoxyethylene （POE） chain and tends to a plateau after the DP around 114,i.e. the long chain structure of POE is favourable to the antithrombogenicityof its copolymers ;moreover, the extent of the improvement ofantithrombogenicity also relates to the PEGMM content of the copolymers and the kind of the matrix that the POE chains are located on. These results are consistent with the anticipation of the hypothesis of maintaining proteins normal conformations for blood compatible bioraaterials.

Experimental Study on Malignant Transformation of Human Bronchial Epithelial Cells Induced by Glycidyl Methacrylate and Analysis on its Methylation

Objective To establish the model of human bronchial epithelial cells （16HBE） malignant transformation induced by glycidyl methacrylate （GMA） and define the different methylation genes at different stages. Methods DNA was extracted at different 16HBE malignant phases and methylation at different stages were detected using Methylation chip of Promoter Microarray Methylation＇. Methylation-specific PCR （MSP） was methylation status of some genes, and then compared with the control groups. changes of genes DNA ＇NimbleGen HG18 CpG used to observe the Results The result showed that GMA induced 16HBE morphorlogical transformation at the dose of 8 I^g/mL, and cell exposed to GMA had 1 374 genes in protophase, 825 genes in metaphase, 1 149 genes in anaphase, respectively; 30 genes are all methylation in the 3 stages; 318 genes in protophase but not in metaphase and anaphase; 272 genes in metaphase but not in protophase and anaphase; 683 genes in anaphase but not in metaphase and protophase; 73 genes in protophase and metaphase but not in anaphase; 67 genes in protophase and anaphase but not in metaphase; 59 genes in metaphase and anaphase but not in protophase. Conclusion The pattern of DNA methylation could change in the process of 16HBE induced by GMA.

SURFACE MODIFICATION OF MICROPOROUS POLYPROPYLENE MEMBRANES BY GRAFT POLYMERIZATION OF N,N-DIMETHYLAMINOETHYL METHACRYLATE

Surface modification of microporous polypropylene hollow fiber membranes was performed by radical-induced graft polymerization of N,N-dimethylaminoethyl methacrylate (DMAEMA). The influences of temperature, monomer concentration and pre-adsorbed amount of benzoyl peroxide on grafting degree were studied respectively. It was found that the appropriate graft temperature was 75 'C, at which the grafting degree was the highest and the hydrolytic decomposition of DMAEMA the lowest. Scanning electron photomicrography and the average pore diameters of the modified membranes demonstrated that part of the micropores on the membrane surface was plugged by the grafted polyDMAEMA chains, especially at high grafting degree. Contact angle and water swelling experiments showed that a moderate grafting degree could improve the hydrophilicity of the membranes. In the range of 11.3%-12.0% grafting degree, the water swelling percentage reached its maximum (51.1%) and the contact angle reached its minimum (74 degrees). The bovine serum albumin (BSA) adsorption experiment indicated that the grafted polyDMAEMA had a dual effect on protein adsorption. At the first stage, the BSA adsorption decreased with increasing of DMAEMA grafting degree. As the interaction between BSA and polyDMAEMA on membrane surface increased, the BSA adsorption increased with increasing of DMAEMA grafting degree.

Primer containing dimethylaminododecyl methacrylate kills bacteria impregnated in human dentin blocks

Antibacterial dimethylaminododecyl methacrylate （DMADDM） was recently synthesized. The objectives of this study were to： （1） investigate antibacterial activity of DMADDM-containing primer on Streptococcus mutans impregnated into dentin blocks for the first time, and （2） compare the antibacterial efficacy of DMADDM with a previous quaternary ammonium dimethacrylate （QADM）. Scotchbond Multi-Purpose （SBMP） bonding agent was used. DMADDM and QADM were mixed into SBMP primer. Six primers were tested： SBMP control primer P, P＋2.5% DMADDM, P＋5% DMADDM, P＋7.5% DMADDM, P＋10% DMADDM, and P＋10% QADM. S. mutans were impregnated into human dentin blocks, and each primer was applied to dentin to test its ability to kill bacteria in dentinal tubules. Bacteria in dentin were collected via a sonication method, and the colony-forming units （CFU） and inhibition zones were measured. The bacterial inhibition zone of P＋10% DMADDM was 10 times that of control primer （P〈0.05）. CFU in dentin with P＋10% DMADDM was reduced by three orders of magnitude, compared with control. DMADDM had a much stronger antibacterial effect than QADM, and antibacterial efficacy increased with increasing DMADDM concentration. Dentin shear bond strengths were similar among all groups （P〉0.1）. In conclusion, antibacterial DMADDM-containing primer was validated to kill bacteria inside dentin blocks, possessing a much stronger antibacterial potency than the previous QADM. DMADDM-containing bonding agent was effective in eradicating bacteria in dentin, and its efficacy was directly proportional to DMADDM mass fraction. Therefore, DMADDM may be promisine for use in bonding agents as well as in other restorative and oreventive materials to inhibit bacteria.