Despite being one of the oldest and most widely-used turbulence models in engineering computational fluid dynamics(CFD),the k-ωmodel has not been fully understood theoretically because of its high nonlinearity and co...Despite being one of the oldest and most widely-used turbulence models in engineering computational fluid dynamics(CFD),the k-ωmodel has not been fully understood theoretically because of its high nonlinearity and complex model parameter setting.Here,a multi-layer analytic expression is postulated for two lengths(stress and kinetic energy lengths),yielding an analytic solution for the k-ωmodel equations in pipe flow.Approximate local balance equations are analyzed to determine the key parameters in the solution,which are shown to be rather close to the empirically-measured values from the numerical solution of the Wilcox k-ωmodel,and hence the analytic construction is fully validated.The results provide clear evidence that the k-ωmodel sets in it a multilayer structure,which is similar to but different,in some insignificant details,from the Navier-Stokes(N-S)turbulence.This finding explains why the k-ωmodel is so popular,especially in computing the near-wall flow.Finally,the analysis is extended to a newlyrefined k-ωmodel called the structural ensemble dynamics(SED)k-ωmodel,showing that the SED k-ωmodel has improved the multi-layer structure in the outer flow but preserved the setting of the k-ωmodel in the inner region.展开更多
New energy vehicles have better clean and environmental protection characteristics than traditional fuel vehicles.The new energy engine cooling technology is critical in the design of new energy vehicles.This paper us...New energy vehicles have better clean and environmental protection characteristics than traditional fuel vehicles.The new energy engine cooling technology is critical in the design of new energy vehicles.This paper used oneand three-way joint simulation methods to simulate the refrigeration system of new energy vehicles.Firstly,a k-εturbulent flow model for the cooling pump flow field is established based on the principle of computational fluid dynamics.Then,the CFD commercial fluid analysis software FLUENT is used to simulate the flow field of the cooling pump under different inlet flow conditions.This paper proposes an optimization scheme for new energy vehicle engines’“boiling”phenomenon under high temperatures and long-time climbing conditions.The simulation results show that changing the radiator’s structure and adjusting the thermostat’s parameters can solve the problem of a“boiling pot.”The optimized new energy vehicle engine can maintain a better operating temperature range.The algorithm model can reference each cryogenic system component hardware selection and control strategy in the new energy vehicle’s engine.展开更多
The internal turbulent flow in conical diffuser is a very complicated adverse pressure gradient flow.DLR k-ε turbulence model was adopted to study it.The every terms of the Laplace operator in DLR k-ε turbulence mod...The internal turbulent flow in conical diffuser is a very complicated adverse pressure gradient flow.DLR k-ε turbulence model was adopted to study it.The every terms of the Laplace operator in DLR k-ε turbulence model and pressure Poisson equation were discretized by upwind difference scheme.A new full implicit difference scheme of 5-point was constructed by using finite volume method and finite difference method.A large sparse matrix with five diagonals was formed and was stored by three arrays of one dimension in a compressed mode.General iterative methods do not work wel1 with large sparse matrix.With algebraic multigrid method(AMG),linear algebraic system of equations was solved and the precision was set at 10-6.The computation results were compared with the experimental results.The results show that the computation results have a good agreement with the experiment data.The precision of computational results and numerical simulation efficiency are greatly improved.展开更多
Local heat transfer and flow characteristics in a round turbulent impinging jet for Re≈23 000 is predicted numerically with the RANS approach and a k-ε-fu turbulence model. The heat transfer predictions and turbulen...Local heat transfer and flow characteristics in a round turbulent impinging jet for Re≈23 000 is predicted numerically with the RANS approach and a k-ε-fu turbulence model. The heat transfer predictions and turbulence parameters are verified against the axis-symmetric free jet impingement measurements and compared with previous other turbulence models, and results show the k-ε-fu model has a good performance in predictions of the local wall heat transfer coefficient, and in agreement with measurements in mean velocity profiles at different radial positions as well. The numerical model is further used to examine the effect of the fully confined impingement jet on the local Nusselt number. Local Nusselt profiles in x and y-centerlines for the target plate over three separation distances are predicted. Compared with the experimental data, the numerical results are accurate in the central domain around the stagnation region and present a consistent structure distribution.展开更多
The research is motivated by the ongoing the electromagnetic continuous casting of molten metal. The revised k-ε model considering the effect of magnetic field application was derived. The specific model equations fo...The research is motivated by the ongoing the electromagnetic continuous casting of molten metal. The revised k-ε model considering the effect of magnetic field application was derived. The specific model equations for the electromagnetic braking were used to calculate the velocity distribution in the continuous casting mold of steel. The results show that the revised k-ε model considering the effect of magnetic field application tends to suppress the production of turbulence and difference between the conventional and revised k-e model is small.展开更多
A two-equation turbulence model has been dereloped for predicting two-phase flow the two equations describe the conserration of turbulence kinetic energy and dissipation rate of that energy for the incompressible carr...A two-equation turbulence model has been dereloped for predicting two-phase flow the two equations describe the conserration of turbulence kinetic energy and dissipation rate of that energy for the incompressible carrier fluid in a two-phase flow The continuity, the momentum, K and εequations are modeled. In this model,the solid-liquid slip veloeites, the particle-particte interactions and the interactions between two phases are considered,The sandy water pipe turbulent flows are sueeessfuly predicted by this turbulince model.展开更多
By modifying the Rodi assumption to take account of the influence of flow curvature, a new curvature modified algebraic stress model(CMASM) is de- veloped from the second moment closure in the generalized curvilinear ...By modifying the Rodi assumption to take account of the influence of flow curvature, a new curvature modified algebraic stress model(CMASM) is de- veloped from the second moment closure in the generalized curvilinear coordinate system. And the explicit form of this ASM, a new curvature modified nonlinear k-ε model (CMNKE), is derived in the orthogonal curvilinear coordinate system. This new nonlinear k-ε model is further validated by a numerical simulation of a two- dimensional U-type turnaround duct flow. The results show that the CMNKE can effectively capture the main characteristic of this curvature flow and simulate the damping effect of the shear stress by a convex curvature and the enhancing effect by a concave curvature. So, this model is a rational and effective simplification to the second moment closure.展开更多
The paper presents the k-ε model equations of turbulence with a single set of constants chosen by the authors, which is appropriate to simulate a wide range of turbulent flows. The model validation has been performed...The paper presents the k-ε model equations of turbulence with a single set of constants chosen by the authors, which is appropriate to simulate a wide range of turbulent flows. The model validation has been performed for a number of flows and its main results are given in the paper. The turbulent mixing of flow with shear in the tangential velocity component is discussed in details. An analytical solution to the system of ordinary differential equations of the k-ε model of turbulent mixing has been found for the self-similar regime of flow. The model coefficients were chosen using simulation results for some simplest turbulent flows. The solution can be used for the verification of codes. The numerical simulation of the problem has been performed by the 2D code EGAK using this model. A good agreement of the numerical simulation results with the self-similar solution, 3D DNS results and known experimental data has been achieved. This allows stating that the k-ε model constants chosen by the authors are acceptable for the considered flow.展开更多
In turbulence modeling, the RNG and Realizable models have important improvements in the turbulent production and dissipation terms in comparison to the Standard. The selection of the appropriate turbulence model has ...In turbulence modeling, the RNG and Realizable models have important improvements in the turbulent production and dissipation terms in comparison to the Standard. The selection of the appropriate turbulence model has an impact on the convergence and solution in STRs, and they are used in mixing, multiphase modeling or as starting solution of transient models as DES and LES. Although there are several studies with the pitched blade turbine(PBT) impeller, most of them used the Standard model as representative of all k–ε models, using structured hexahedral grids composed of low number of cells, and in some cases under axial symmetry assumptions.Accordingly, in this work the assessment of the Standard, RNG and Realizable models to describe the turbulent flow field of this impeller, using the Multiple Reference Frame(MRF) and Sliding Mesh(SM) approaches with tetrahedral domains in dense grids, is presented. This kind of cell elements is especially suitable to reproduce complex geometries. Flow velocities and turbulent parameters were verified experimentally by PIV and torque measurements. The three models were capable of predicting fairly the pumping number, the power number based on torque, and velocities. Although the RNG improved the predictions of the turbulent kinetic energy and dissipation rate, the Realizable model presented better performance for both approaches. All models failed in the prediction of the total dissipation rate, and a dependence of its value on the number of cells for the MRF was found.展开更多
Discrete choice model acts as one of the most important tools for studies involving mode split in the context of transport demand forecast. As different types of discrete choice models display their merits and restric...Discrete choice model acts as one of the most important tools for studies involving mode split in the context of transport demand forecast. As different types of discrete choice models display their merits and restrictions diversely, how to properly select the specific type among discrete choice models for realistic application still remains to be a tough problem. In this article, five typical discrete choice models for transport mode split are, respectively, discussed, which includes multinomial logit model, nested logit model （NL）, heteroscedastic extreme value model, multinominal probit model and mixed multinomial logit model （MMNL）. The theoretical basis and application attributes of these five models are especially analysed with great attention, and they are also applied to a realistic intercity case of mode split forecast, which results indi- cating that NL model does well in accommodating similarity and heterogeneity across alternatives, while MMNL model serves as the most effective method for mode choice prediction since it shows the highest reliability with the least significant prediction errors and even outperforms the other four models in solving the heterogeneity and similarity problems. This study indicates that conclusions derived from a single discrete choice model are not reliable, and it is better to choose the proper model based on its characteristics.展开更多
Cavitation is a complex flow phenomenon including unsteady characteristics, turbulence, gas-liquid two-phase flow. This paper provides a numerical investigation on comparing the simulation performance of three differe...Cavitation is a complex flow phenomenon including unsteady characteristics, turbulence, gas-liquid two-phase flow. This paper provides a numerical investigation on comparing the simulation performance of three different models in OpenFOAM-Merkle model, Kunz model and Schnerr-Sauer model, which is helpful for understanding the cavitation flow. Considering the influence of vapor-liquid mixing density on turbulent viscous coefficient, the modified SST k-ω model is adopted in this paper to increase the computing reliability. The InterPhaseChangeFoam solver is utilized to simulate the two-dimensional cavitation flow of the Clark-Y hydrofoil with three cavitation models. The hydrodynamic performance including lift coefficient, drag coefficient and cavitation flow shape of the hydrofoil is analyzed. Through the comparison of the numerical results and experimental data, it is found that the Schnerr-Sauer model can get the most accurate results among the three models. And from the simulation point of water and water vapor mixing, the Merkle model has the best water and water vapor mixing simulation.展开更多
A two-equation K-ε turbulent fluid flow model is built to model the heat transfer and fluid flow in gas tungsten arc welding （GTAW） process of stainless steel S US310 and S US316. This model combines the buoyancy f...A two-equation K-ε turbulent fluid flow model is built to model the heat transfer and fluid flow in gas tungsten arc welding （GTAW） process of stainless steel S US310 and S US316. This model combines the buoyancy force, lorentz force and marangni force as the driving forces of thefluidflow in the weld pool. The material properties are functions of temperature in this model. The simulated results show that the molten metal flowing outward is mainly caused by the marangoni convection, which makes the weld pool become wider and shallower. The comparison of the weld pool shape of SUS310 and SUS316 shows that the slight differences of the value of thermal conductivity mainly attributes to the difference of the weld pool shape and the distinction of heat transport in laminar and turbulent model makes large diversity in the simulated results.展开更多
基金the National Numerical Wind Tunnel(No.NNW2019ZT1-A03)the National Natural Science Foundation of China(Nos.91952201,11372008,and 11452002)。
文摘Despite being one of the oldest and most widely-used turbulence models in engineering computational fluid dynamics(CFD),the k-ωmodel has not been fully understood theoretically because of its high nonlinearity and complex model parameter setting.Here,a multi-layer analytic expression is postulated for two lengths(stress and kinetic energy lengths),yielding an analytic solution for the k-ωmodel equations in pipe flow.Approximate local balance equations are analyzed to determine the key parameters in the solution,which are shown to be rather close to the empirically-measured values from the numerical solution of the Wilcox k-ωmodel,and hence the analytic construction is fully validated.The results provide clear evidence that the k-ωmodel sets in it a multilayer structure,which is similar to but different,in some insignificant details,from the Navier-Stokes(N-S)turbulence.This finding explains why the k-ωmodel is so popular,especially in computing the near-wall flow.Finally,the analysis is extended to a newlyrefined k-ωmodel called the structural ensemble dynamics(SED)k-ωmodel,showing that the SED k-ωmodel has improved the multi-layer structure in the outer flow but preserved the setting of the k-ωmodel in the inner region.
文摘New energy vehicles have better clean and environmental protection characteristics than traditional fuel vehicles.The new energy engine cooling technology is critical in the design of new energy vehicles.This paper used oneand three-way joint simulation methods to simulate the refrigeration system of new energy vehicles.Firstly,a k-εturbulent flow model for the cooling pump flow field is established based on the principle of computational fluid dynamics.Then,the CFD commercial fluid analysis software FLUENT is used to simulate the flow field of the cooling pump under different inlet flow conditions.This paper proposes an optimization scheme for new energy vehicle engines’“boiling”phenomenon under high temperatures and long-time climbing conditions.The simulation results show that changing the radiator’s structure and adjusting the thermostat’s parameters can solve the problem of a“boiling pot.”The optimized new energy vehicle engine can maintain a better operating temperature range.The algorithm model can reference each cryogenic system component hardware selection and control strategy in the new energy vehicle’s engine.
基金Projects(59375211,10771178,10676031) supported by the National Natural Science Foundation of ChinaProject(07A068) supported by the Key Project of Hunan Education CommissionProject(2005CB321702) supported by the National Key Basic Research Program of China
文摘The internal turbulent flow in conical diffuser is a very complicated adverse pressure gradient flow.DLR k-ε turbulence model was adopted to study it.The every terms of the Laplace operator in DLR k-ε turbulence model and pressure Poisson equation were discretized by upwind difference scheme.A new full implicit difference scheme of 5-point was constructed by using finite volume method and finite difference method.A large sparse matrix with five diagonals was formed and was stored by three arrays of one dimension in a compressed mode.General iterative methods do not work wel1 with large sparse matrix.With algebraic multigrid method(AMG),linear algebraic system of equations was solved and the precision was set at 10-6.The computation results were compared with the experimental results.The results show that the computation results have a good agreement with the experiment data.The precision of computational results and numerical simulation efficiency are greatly improved.
基金Sponsored by the National Natural Science Foundation of China(Grant No.51576054)
文摘Local heat transfer and flow characteristics in a round turbulent impinging jet for Re≈23 000 is predicted numerically with the RANS approach and a k-ε-fu turbulence model. The heat transfer predictions and turbulence parameters are verified against the axis-symmetric free jet impingement measurements and compared with previous other turbulence models, and results show the k-ε-fu model has a good performance in predictions of the local wall heat transfer coefficient, and in agreement with measurements in mean velocity profiles at different radial positions as well. The numerical model is further used to examine the effect of the fully confined impingement jet on the local Nusselt number. Local Nusselt profiles in x and y-centerlines for the target plate over three separation distances are predicted. Compared with the experimental data, the numerical results are accurate in the central domain around the stagnation region and present a consistent structure distribution.
文摘The research is motivated by the ongoing the electromagnetic continuous casting of molten metal. The revised k-ε model considering the effect of magnetic field application was derived. The specific model equations for the electromagnetic braking were used to calculate the velocity distribution in the continuous casting mold of steel. The results show that the revised k-ε model considering the effect of magnetic field application tends to suppress the production of turbulence and difference between the conventional and revised k-e model is small.
文摘A two-equation turbulence model has been dereloped for predicting two-phase flow the two equations describe the conserration of turbulence kinetic energy and dissipation rate of that energy for the incompressible carrier fluid in a two-phase flow The continuity, the momentum, K and εequations are modeled. In this model,the solid-liquid slip veloeites, the particle-particte interactions and the interactions between two phases are considered,The sandy water pipe turbulent flows are sueeessfuly predicted by this turbulince model.
基金The project supported by the National Natural Science Foundation of China (19725208)the National Climbing project of China
文摘By modifying the Rodi assumption to take account of the influence of flow curvature, a new curvature modified algebraic stress model(CMASM) is de- veloped from the second moment closure in the generalized curvilinear coordinate system. And the explicit form of this ASM, a new curvature modified nonlinear k-ε model (CMNKE), is derived in the orthogonal curvilinear coordinate system. This new nonlinear k-ε model is further validated by a numerical simulation of a two- dimensional U-type turnaround duct flow. The results show that the CMNKE can effectively capture the main characteristic of this curvature flow and simulate the damping effect of the shear stress by a convex curvature and the enhancing effect by a concave curvature. So, this model is a rational and effective simplification to the second moment closure.
文摘The paper presents the k-ε model equations of turbulence with a single set of constants chosen by the authors, which is appropriate to simulate a wide range of turbulent flows. The model validation has been performed for a number of flows and its main results are given in the paper. The turbulent mixing of flow with shear in the tangential velocity component is discussed in details. An analytical solution to the system of ordinary differential equations of the k-ε model of turbulent mixing has been found for the self-similar regime of flow. The model coefficients were chosen using simulation results for some simplest turbulent flows. The solution can be used for the verification of codes. The numerical simulation of the problem has been performed by the 2D code EGAK using this model. A good agreement of the numerical simulation results with the self-similar solution, 3D DNS results and known experimental data has been achieved. This allows stating that the k-ε model constants chosen by the authors are acceptable for the considered flow.
基金the National Council of Science and Technology, Mexico CONACyT for the support provided for this research, through the Basic Science project CB-2011/ 169786
文摘In turbulence modeling, the RNG and Realizable models have important improvements in the turbulent production and dissipation terms in comparison to the Standard. The selection of the appropriate turbulence model has an impact on the convergence and solution in STRs, and they are used in mixing, multiphase modeling or as starting solution of transient models as DES and LES. Although there are several studies with the pitched blade turbine(PBT) impeller, most of them used the Standard model as representative of all k–ε models, using structured hexahedral grids composed of low number of cells, and in some cases under axial symmetry assumptions.Accordingly, in this work the assessment of the Standard, RNG and Realizable models to describe the turbulent flow field of this impeller, using the Multiple Reference Frame(MRF) and Sliding Mesh(SM) approaches with tetrahedral domains in dense grids, is presented. This kind of cell elements is especially suitable to reproduce complex geometries. Flow velocities and turbulent parameters were verified experimentally by PIV and torque measurements. The three models were capable of predicting fairly the pumping number, the power number based on torque, and velocities. Although the RNG improved the predictions of the turbulent kinetic energy and dissipation rate, the Realizable model presented better performance for both approaches. All models failed in the prediction of the total dissipation rate, and a dependence of its value on the number of cells for the MRF was found.
基金supported by the Science&Technology pillar project(No.0556)of Guangzhou
文摘Discrete choice model acts as one of the most important tools for studies involving mode split in the context of transport demand forecast. As different types of discrete choice models display their merits and restrictions diversely, how to properly select the specific type among discrete choice models for realistic application still remains to be a tough problem. In this article, five typical discrete choice models for transport mode split are, respectively, discussed, which includes multinomial logit model, nested logit model （NL）, heteroscedastic extreme value model, multinominal probit model and mixed multinomial logit model （MMNL）. The theoretical basis and application attributes of these five models are especially analysed with great attention, and they are also applied to a realistic intercity case of mode split forecast, which results indi- cating that NL model does well in accommodating similarity and heterogeneity across alternatives, while MMNL model serves as the most effective method for mode choice prediction since it shows the highest reliability with the least significant prediction errors and even outperforms the other four models in solving the heterogeneity and similarity problems. This study indicates that conclusions derived from a single discrete choice model are not reliable, and it is better to choose the proper model based on its characteristics.
文摘Cavitation is a complex flow phenomenon including unsteady characteristics, turbulence, gas-liquid two-phase flow. This paper provides a numerical investigation on comparing the simulation performance of three different models in OpenFOAM-Merkle model, Kunz model and Schnerr-Sauer model, which is helpful for understanding the cavitation flow. Considering the influence of vapor-liquid mixing density on turbulent viscous coefficient, the modified SST k-ω model is adopted in this paper to increase the computing reliability. The InterPhaseChangeFoam solver is utilized to simulate the two-dimensional cavitation flow of the Clark-Y hydrofoil with three cavitation models. The hydrodynamic performance including lift coefficient, drag coefficient and cavitation flow shape of the hydrofoil is analyzed. Through the comparison of the numerical results and experimental data, it is found that the Schnerr-Sauer model can get the most accurate results among the three models. And from the simulation point of water and water vapor mixing, the Merkle model has the best water and water vapor mixing simulation.
基金The research is supported by China Postdoctoral Science Foundation （No. 20080430129 ） and National Key Technology R＆D Program （ No. 2007 BAE07 B07 ）.
文摘A two-equation K-ε turbulent fluid flow model is built to model the heat transfer and fluid flow in gas tungsten arc welding （GTAW） process of stainless steel S US310 and S US316. This model combines the buoyancy force, lorentz force and marangni force as the driving forces of thefluidflow in the weld pool. The material properties are functions of temperature in this model. The simulated results show that the molten metal flowing outward is mainly caused by the marangoni convection, which makes the weld pool become wider and shallower. The comparison of the weld pool shape of SUS310 and SUS316 shows that the slight differences of the value of thermal conductivity mainly attributes to the difference of the weld pool shape and the distinction of heat transport in laminar and turbulent model makes large diversity in the simulated results.
