Synthesis of NO by rotating sliding arc discharge reactor with conical-spiral electrodes

The present work investigates the potential applications of nitrogen oxides(NO_(x)),particularly nitric oxide(NO)and nitrogen dioxide(NO_(2)),generated through discharge plasma in diverse sectors such as medicine,nitrogen fixation,energy,and environmental protection.In this study,a rotating sliding arc discharge reactor was initially employed to produce high concentrations of gaseous NO_(x),followed by the utilization of a molybdenum wire redox reactor for NO_(2)-to-NO conversion.The outcomes reveal that the discharge states and generations of NO_(x) are affected by varying parameters,including the applied energies,frequencies and airflow states(1.3-2.6 m/s are the laminar flow,2.6-5.2 m/s are the transition state,5.2-6.5 m/s are the turbulent flow),and the concentrations of NO_(x) within the arc discharge are higher than that in the spark discharge.Moreover,the concentrations of NO,NO_(2) and NO_(x) gradually increased,and the concentration ratios of NO/NO_(2) and NO_(x)/NO_(2) decreased with increasing the applied energy for one cycle from 14.8 mJ to 24.3 mJ.Meanwhile,the concentrations of NO,NO_(2) and NO_(x) gradually decreased,and the concentration ratios of NO/NO_(2) and NO_(x)/NO_(2) first decreased and then increased with increasing the applied frequencies from 5.0 kHz to 9.0 kHz.Further,the concentrations of NO,NO_(2) and NO_(x) gradually decreased,and the concentration ratios of NO/NO_(2) and NO_(x)/NO_(2) first increased and then decreased with increasing the air flow speeds from 1.3 m/s to 6.5 m/s.Lastly,the concentrations of NO increased and NO_(2) decreased with increasing temperature from 25℃ to 400℃ using molybdenum converted.These findings provide experimental support for the application of plasma in the fields of medicine,nitrogen fixation,energy and environmental protection.

Discharge behavior and electrochemical properties of Mg-Al-Sn alloy anode for seawater activated battery

Mg-Al-Sn alloy is one of the new developed anode materials for seawater activated batteries. The potentiodynamic polarization, galvanostatic discharge and electrochemical impedance spectroscopy of Mg-6%Al-1%Sn and Mg-6%Al-5%Sn(mass fraction) alloys in seawater were studied and compared with the commercial AZ31 and AP65 alloys. The results show that the Mg-6%Al-1%Sn alloy obtains the most negative discharge potential of average-1.611V with a electric current density of 100 mA/cm2. EIS studies reveal that the Mg-Al-Sn alloy/seawater interfacial electrochemical process is determined by an activation controlled reaction. The assembled prototype batteries with Mg-6%Al-1%Sn alloy as anodes and Ag Cl as cathodes exhibit a satisfactory integrated discharge properties.

基于NOD样受体3炎性小体通路对利拉鲁肽在氧化低密度脂蛋白诱导内皮细胞损伤的作用机制研究

背景动脉粥样硬化是世界范围内引起心脑血管疾病最主要的原因,炎症是目前研究热点,其中NOD样受体3(NLRP3)是研究最为深入的炎症小体。胰高糖素样肽1(GLP-1)受体激动剂有抗动脉粥样硬化作用,具体机制尚不明确。目的研究利拉鲁肽通过拮抗氧化低密度脂蛋白(ox-LDL)诱导的内皮细胞损伤的作用机制。方法2022-03-25—05-19培养人脐静脉内皮细胞(HUVEC),取HUVEC加空白血清作为对照组,100μg/mL的ox-LDL干预HUVEC 48 h作为模型组,100μg/mL的ox-LDL干预HUVEC 24 h后分别加入100、200、400 nmol/L利拉鲁肽处理24 h作为利拉鲁肽低浓度组、利拉鲁肽中浓度组、利拉鲁肽高浓度组。CCK-8法计算细胞增殖率。通过扫描电镜观察焦亡细胞形态。检测乳酸脱氢酶(LDH)活力。酶联免疫吸附试验(ELISA)检测白介素(IL)-1β、IL-18表达水平。蛋白质免疫印迹试验(Western blot)检测NLRP3、接头蛋白凋亡相关斑点样蛋白(ASC)、天冬氨酸蛋白水解酶1(Caspase-1)、焦亡执行蛋白(GSDMD)、N端结构域的焦亡执行蛋白(N-GSDMD)表达水平。结果模型组、利拉鲁肽低浓度组和利拉鲁肽中浓度组细胞增殖率低于对照组,利拉鲁肽低浓度组、利拉鲁肽中浓度组、利拉鲁肽高浓度组细胞增殖率高于模型组(P<0.05)。细胞扫描电镜结果示模型组细胞焦亡明显,利拉鲁肽低浓度组、利拉鲁肽中浓度组、利拉鲁肽高浓度组细胞焦亡情况明显改善。模型组、利拉鲁肽低浓度组LDH活力高于对照组,利拉鲁肽低浓度组、利拉鲁肽中浓度组、利拉鲁肽高浓度组低于模型组(P<0.05)。模型组、利拉鲁肽低浓度组IL-1β表达水平高于对照组,利拉鲁肽中浓度组、利拉鲁肽高浓度组IL-1β表达水平低于模型组(P<0.05);模型组IL-18表达水平高于对照组,利拉鲁肽低浓度组、利拉鲁肽中浓度组、利拉鲁肽高浓度组IL-18表达水平低于模型组(P<0.05)。模型组NLRP3、ASC、Caspase-1、GSDMD、N-GSDMD表达水平高于对照组,利拉鲁肽低浓度组ASC、Caspase-1表达水平高于对照组,利拉鲁肽中浓度组NLRP3、ASC表达水平低于模型组,利拉鲁肽高浓度组NLRP3、ASC、Caspase-1表达水平低于模型组(P<0.05)。结论利拉鲁肽显著抑制ox-LDL诱导的内皮细胞NLRP3炎性小体活化,并且能够抑制内皮细胞的焦亡,具有抗动脉粥样硬化作用。

Recent advances in high charge density triboelectric nanogenerators

Triboelectric materials with high charge density are the building-block for the commercial application of triboelectric nanogenerators(TENGs).Unstable dynamic processes influence the change of the charge density on the surface and inside of triboelectric materials.The charge density of triboelectric materials depends on the surface and the internal charge transfer processes.The focus of this review is on recent advances in high charge density triboelectric materials and advances in the fabrication of TENGs.We summarize the existing strategies for achieving high charge density in triboelectric materials as well as their fundamental properties.We then review current optimization methods for regulating dynamic charge transfer processes to increase the output charge density:first,increasing charge injection and limiting charge dissipation to achieve a high average surface charge density,and second,regulating the internal charge transfer process and storing charge in triboelectric materials to increase the output charge density.Finally,we present the challenges and prospects in developing high-performance triboelectric materials.

Multilevel carbon architecture of subnanoscopic silicon for fast‐charging high‐energy‐density lithium‐ion batteries

Silicon(Si)is widely used as a lithium‐ion‐battery anode owing to its high capacity and abundant crustal reserves.However,large volume change upon cycling and poor conductivity of Si cause rapid capacity decay and poor fast‐charging capability limiting its commercial applications.Here,we propose a multilevel carbon architecture with vertical graphene sheets(VGSs)grown on surfaces of subnanoscopically and homogeneously dispersed Si–C composite nanospheres,which are subsequently embedded into a carbon matrix(C/VGSs@Si–C).Subnanoscopic C in the Si–C nanospheres,VGSs,and carbon matrix form a three‐dimensional conductive and robust network,which significantly improves the conductivity and suppresses the volume expansion of Si,thereby boosting charge transport and improving electrode stability.The VGSs with vast exposed edges considerably increase the contact area with the carbon matrix and supply directional transport channels through the entire material,which boosts charge transport.The carbon matrix encapsulates VGSs@Si–C to decrease the specific surface area and increase tap density,thus yielding high first Coulombic efficiency and electrode compaction density.Consequently,C/VGSs@Si–C delivers excellent Li‐ion storage performances under industrial electrode conditions.In particular,the full cells show high energy densities of 603.5 Wh kg^(−1)and 1685.5 Wh L^(−1)at 0.1 C and maintain 80.7%of the energy density at 3 C.

Inter-comparison of field snow measurements using different instruments in Türkiye

Snow is important in Türkiye especially in the mountainous eastern areas where it may stay on the ground for more than half of the year.This region plays a vital role in feeding the water resources of the trans-boundary Euphrates-Tigris Basin,supporting crucial dams for water supply,irrigation and energy production.Thus,easy,frequent,correct and economical ways of measuring the snowpack is crucial.The snow properties at specific locations in the mountainous eastern regions over the two snow seasons(2018 and 2019)were studied by using different instruments and techniques,snow pit(box/cylinder/wedge cutter types),snow tube(Federal Sampler)and SnoTel(Snowpack Analyzer).The results point out a 1.7%-7.1%variation between different cutter type snow density measurements within snow pit analysis and the long-term utilized snow tube observations show a closer relation to box/cylinder type cutters.As for the continuous SnoTel observations,a variation of 2.4%-9.8%with various cutter types and a 5.9%difference regarding the snow tube density results are detected.These findings indicate a close range among different instruments,but it is the best when all three systems complement each other to characterize the snowpack effectively in the complex terrain since each has its own advantages.

Predictors of Abnormal Vaginal Discharge among Women of Reproductive Age in Southeast Nigeria

Background: An abnormal vaginal discharge is a common complaint among women of reproductive age, and it can indicate serious conditions like pelvic inflammatory disease and cervical cancer. This study aimed to assess the predictors of abnormal vaginal discharge in women of reproductive age group in Imo State, Southeast Nigeria. Methods: A cross-sectional study was conducted among 368 women of reproductive age group attending the clinic at Federal University Teaching Hospital Owerri, in Imo State, Nigeria. Respondents were recruited using a systematic sampling technique. Data were collected using a pre-tested interviewer-administered questionnaire. Multivariable analysis was performed to determine predictors of abnormal vaginal discharge. Statistical significance was set at p Results: The mean age of the respondents was 30 ± 4.5 years. Predictors of abnormal vaginal discharge were: age 36 - 45 years (OR: 4.5;95% C.I: 1.023 - 8.967, p = 0.041), being a student (OR: 2.4: 95% C.I: 1.496 - 7.336, p = 0.003), use of oral contraceptives (OR: 3.4;95% C.I: 1.068 - 6.932, p = 0.010), use of water cistern (OR: 4.7;C.I: 1.654 - 5.210, p = 0.028) anal hygiene practices (OR: 2.7;95% C.I: 1.142 - 4.809, p Conclusion: These findings suggest that targeted sexual and reproductive health interventions should be provided to reduce the risk of abnormal vaginal discharge in women of reproductive age group.

Tailoring the microstructure of Mg-Al-Sn-RE alloy via friction stir processing and the impact on its electrochemical discharge behaviour as the anode for Mg-air battery

Constructing the magnesium alloy with fine grains,low density of dislocations,and weak crystal orientation is of crucial importance to enhance its comprehensive performance as the anode for Mg-air battery.However,this unique microstructure can hardly be achieved with conventional plastic deformation such as rolling or extrusion.Herein,we tailor the microstructure of Mg-Al-Sn-RE alloy by using the friction stir processing,which obviously refines the grains without increasing dislocation density or strengthening crystal orientation.The Mg-air battery with the processed Mg-Al-Sn-RE alloy as the anode exhibits higher discharge voltages and capacities than that employing the untreated anode.Furthermore,the impact of friction stir processing on the electrochemical discharge behaviour of Mg-Al-Sn-RE anode and the corresponding mechanism are also analysed according to microstructure characterization and electrochemical response.

Machine learning for parameters diagnosis of spark discharge by electro-acoustic signal

Discharge plasma parameter measurement is a key focus in low-temperature plasma research.Traditional diagnostics often require costly equipment,whereas electro-acoustic signals provide a rich,non-invasive,and less complex source of discharge information.This study harnesses machine learning to decode these signals.It establishes links between electro-acoustic signals and gas discharge parameters,such as power and distance,thus streamlining the prediction process.By building a spark discharge platform to collect electro-acoustic signals and implementing a series of acoustic signal processing techniques,the Mel-Frequency Cepstral Coefficients(MFCCs)of the acoustic signals are extracted to construct the predictors.Three machine learning models(Linear Regression,k-Nearest Neighbors,and Random Forest)are introduced and applied to the predictors to achieve real-time rapid diagnostic measurement of typical spark discharge power and discharge distance.All models display impressive performance in prediction precision and fitting abilities.Among them,the k-Nearest Neighbors model shows the best performance on discharge power prediction with the lowest mean square error(MSE=0.00571)and the highest R-squared value(R^(2)=0.93877).The experimental results show that the relationship between the electro-acoustic signal and the gas discharge power and distance can be effectively constructed based on the machine learning algorithm,which provides a new idea and basis for the online monitoring and real-time diagnosis of plasma parameters.

Investigation of Power Density Amplification in Stacked Triboelectric Nanogenerators

In engineering practice,the output performance of contact separation TENGs(CS-TENGs)increases with the increase of tribo-pair area,which includes increasing the size of single layer CS-TENGs(SCS-TENGs)or the number of units(zigzag TENGs).However,such two strategies show significant differences in output power and power density.In this study,to seek a universal CS-TENG design solution,the output performance of a SCS-TENG and a zigzag TENG(Z-TENG)is systematically compared,including voltage,current,transferred charge,instantaneous power density,and charging power density.The relationship between contact area and output voltages is explored,and the output voltage equation is fitted.The experimental results reveal that SCS-TENGs yield better performance than Z-TENGs in terms of voltage,power,and power density under the same total contact area.Z-TENGs show energy loss during the transfer of mechanical energy,and such loss is aggravated by the increasing number of units.The instantaneous peak power of the SCS-TENG is up to 22 times that of the Z-TENG(45 cm^(2)).Furthermore,the power density of capacitor charging of SCS-TENGs is 131%of that of Z-TENGs,which are relatively close.Z-TENG is a feasible alternative when the working space is limited.

Local thermal conductivity of inhomogeneous nano-fluidic films:A density functional theory perspective

Combining the mean field Pozhar-Gubbins(PG)theory and the weighted density approximation,a novel method for local thermal conductivity of inhomogeneous fluids is proposed.The correlation effect that is beyond the mean field treatment is taken into account by the simulation-based empirical correlations.The application of this method to confined argon in slit pore shows that its prediction agrees well with the simulation results,and that it performs better than the original PG theory as well as the local averaged density model(LADM).In its further application to the nano-fluidic films,the influences of fluid parameters and pore parameters on the thermal conductivity are calculated and investigated.It is found that both the local thermal conductivity and the overall thermal conductivity can be significantly modulated by these parameters.Specifically,in the supercritical states,the thermal conductivity of the confined fluid shows positive correlation to the bulk density as well as the temperature.However,when the bulk density is small,the thermal conductivity exhibits a decrease-increase transition as the temperature is increased.This is also the case in which the temperature is low.In fact,the decrease-increase transition in both the small-bulk-density and low-temperature cases arises from the capillary condensation in the pore.Furthermore,smaller pore width and/or stronger adsorption potential can raise the critical temperature for condensation,and then are beneficial to the enhancement of the thermal conductivity.These modulation behaviors of the local thermal conductivity lead immediately to the significant difference of the overall thermal conductivity in different phase regions.

The Impact of the Inclusion of MgO Nano-Fillers in a Polyethylene Matrix on Dielectric Strength and Resistance to Partial Discharges

One commonly used strategy to enhance polymers specific properties such as the resistance to partial discharges erosion is the incorporation into the polymeric matrix of inorganic micro or nanoparticles. This study focused on the dielectric properties of Low-Density Polyethylene (LDPE) filled with nano-sized Magnesium Oxide (MgO) particles compounded by thermo-mechanical process and one of the purposes was to establish appropriate processing parameters in order to reach the desired dielectric properties. LDPE was used as a matrix and was reinforced by MgO particles having a nominal average size of 30 nm. The MgO nanoparticles were treated with a silane coupling agent (3-Glycidyloxypropyl Trimethoxysilane). The samples were initially prepared in a melt-mixing chamber with a MgO content of 1% wt. These pre-mixed samples were further treated by the means of thermo-mechanical mixing in a conical co-rotating twin-screw extruder in order to improve the dispersion and distribution of the MgO particles. In this report, both lifetime under a PD activity and AC dielectric strength of pure and nano-filled LDPE samples have been measured and compared. Nano-filled LDPE samples were found to exhibit an improve lifetime, without any detrimental impact on their short-term dielectric strength. This suggests that nano-filled LDPE may be for electric applications for which the dielectric materials may be exposed to partial discharge activities. This is significant result for the use of MgO-reinforced PE as an insulating material for HV cables since the resistance to PD is closely related to treeing resistance which is the main electrical degradation mechanism that leads to failure for shielded extruded power cables.

A Clinical Study to Assess the Effectiveness of Oral Combination Kit Therapy in Syndromic Management of Abnormal Vaginal Discharge (FEMINE Study) in Kinshasa, Democratic Republic of Congo

Background: Vaginal discharge is one of most common and nagging problems that women face. About 20% - 25% of women who visit gynecology department complain of vaginal discharge and leucorrhoea. An orally administered combination kit, containing 2 g secnidazole, 1 g azithromycin and 150 mg fluconazole (Azimyn FS Kit), has been successfully evaluated in clinical trials and used in several countries for management syndromic vaginal discharge due to infections. Methods: This is a longitudinal study which aimed to verify the clinical efficacy of the combined oral kit containing secnidazole, azithromycin and fluconazole (Azimyn FS Kit®) in the syndromic treatment of abnormal vaginal discharge in patients received in outpatient consultations in Kinshasa/DR Congo from March to September 2023. Results: Majority of patients had whitish vaginal discharge (51.6%) of average abundance (56.2%), accompanied by pruritus in 72.1% of cases, and dyspareunia in 23.5% of cases and hypogastralgia in 40.2% of cases. One week after treatment with the Azimyn FS® combined kit, at the greatest majority of patients (97.3%), abnormal vaginal discharge had decreased by more than 50% (84.1%). Two weeks after treatment with the Azimyn FS® combined kit, almost all patients (97.3%) no longer had abnormal vaginal discharge which had completely disappeared. Conclusion: A single dose of secnidazole, azithromycin and fluconazole in the form of an oral combi-kit (Azimyn FS Kit) has shown excellent therapeutic effectiveness in the syndromic treatment of abnormal vaginal discharge wherein patients were treated without diagnostic confirmation.

Phase field model for electric-thermal coupled discharge breakdown of polyimide nanocomposites under high frequency electrical stress

In contrast to conventional transformers, power electronic transformers, as an integral component of new energy power system, are often subjected to high-frequency and transient electrical stresses, leading to heightened concerns regarding insulation failures. Meanwhile, the underlying mechanism behind discharge breakdown failure and nanofiller enhancement under high-frequency electrical stress remains unclear. An electric-thermal coupled discharge breakdown phase field model was constructed to study the evolution of the breakdown path in polyimide nanocomposite insulation subjected to high-frequency stress. The investigation focused on analyzing the effect of various factors, including frequency, temperature, and nanofiller shape, on the breakdown path of Polyimide(PI) composites. Additionally, it elucidated the enhancement mechanism of nano-modified composite insulation at the mesoscopic scale. The results indicated that with increasing frequency and temperature, the discharge breakdown path demonstrates accelerated development, accompanied by a gradual dominance of Joule heat energy. This enhancement is attributed to the dispersed electric field distribution and the hindering effect of the nanosheets. The research findings offer a theoretical foundation and methodological framework to inform the optimal design and performance management of new insulating materials utilized in high-frequency power equipment.

Recent advances in fabricating high-performance triboelectric nanogenerators via modulating surface charge density

Triboelectric nanogenerators(TENGs),a type of promising micro/nano energy source,have been arousing tremendous research interest since their inception and have been the subject of many striking developments,including defining the fundamental physical mechanisms,expanding applications in mechanical to electric power conversion and self-powered sensors,etc.TENGs with a superior surface charge density at the interfaces of the electrodes and dielectrics are found to be crucial to the enhancement of the performance of the devices.Here,an overview of recent advances,including material optimization,circuit design,and strategy conjunction,in developing TENGs through surface charge enhancement is presented.In these topics,different strategies are retrospected in terms of charge transport and trapping mechanisms,technical merits,and limitations.Additionally,the current challenges in high-performance TENG research and the perspectives in this field are discussed.

Mitigating volume expansion of silicon-based anode through interfacial engineering based on intermittent discharge strategy

Silicon is considered to be one of the most promising anode materials for lithium-ion batteries(LIBs),but its application is limited by the large volume expansion during alloying and dealloying.The constructing of a high-performance solid electrolyte interface(SEI) film on the surface of the anode material is considered to be one of the effective strategies to mitigate volume expansion of silicon-based anode.In this study,an intermittent discharge strategy which helps to improve the utilization efficiency of electrolyte additive of lithium difluorobisoxalate phosphate(LiDFBOP) is proposed to construct a highly conductive and dense SEI film.The results of electrochemical and physical characterization and theoretical calculations show that the intermittent discharge in the voltage range from open circuit voltage(OCV) to 1.8 V facilitates the diffusion of the soluble products,creates the conditions for the repeated direct contact between Si@C anode and LiDFBOP additive,increases the decomposition of LiDFBOP additive,and thus produces a uniform,dense and inorganics-rich(Li_(2)C_(2)O_(4),LiF and Li_(x)PO_yF_z) SEI film.Subsequently,this SEI film helps to ensure the even intercalation/de-intercalation of Li^(+) in the SEI film and the homogeneous diffusion of Li^(+) inside the Si particles,decreasing the internal stresses and anisotropic phase transitions,maintaining the integrity of Si particles,inhibiting the volume expansion and thu s improving the electrochemical performance of cells.This study not only improves the utilization efficiency of expensive additives through a simply and low-cost method,but also enriches the strategy to improve the electrochemical performance of Si@C anode through interfacial engineering.

A comparative study on the spectral characteristics of nanosecond pulsed discharges in atmospheric He and a He+2.3%H_(2)O mixture

Nanosecond pulsed discharges at atmospheric pressure in a pin-to-pin electrode configuration are well reproducible in time and space, which is beneficial to the fundamentals and applications of low-temperature plasmas. In this experiment, the discharges in helium(He) and He with 2.3%water vapor(H_(2)O) are driven by a series of 10 ns overvoltage pulses(~13 k V). Special attention is paid to the spectral characteristics obtained in the center of discharges by time-resolved optical emission spectroscopy. It is found that in helium, the emission of atomic and molecular helium during the afterglow is more intense than that in the active discharge, while in the He+2.3%H_(2)O mixture, helium emission is only observed during the discharge pulse and the molecular helium emission disappears. In addition, the emissions of OH(A-X) and Hα present similar behavior that increases sharply during the falling edge of the voltage pulse as the electrons cool down rapidly. The gas temperature is set to remain low at 540 K by fitting the OH(A-X) band. A comparative study on the emission of radiative species(He, He_(2), OH and H)is performed between these two discharge cases to derive their main production mechanisms. In both cases, the dominant primary ion is He^(+) at the onset of discharges, but their He^(+) charge transfer processes are quite different. Based on these experimental data and a qualitative discussion on the discharge kinetics, with regard to the present discharge conditions, it is shown that the electron-assisted three-body recombination processes appear to be the significant sources of radiative OH and H species in high-density plasmas.

Fuzzy C-Means Algorithm Based on Density Canopy and Manifold Learning

Fuzzy C-Means(FCM)is an effective and widely used clustering algorithm,but there are still some problems.considering the number of clusters must be determined manually,the local optimal solutions is easily influenced by the random selection of initial cluster centers,and the performance of Euclid distance in complex high-dimensional data is poor.To solve the above problems,the improved FCM clustering algorithm based on density Canopy and Manifold learning(DM-FCM)is proposed.First,a density Canopy algorithm based on improved local density is proposed to automatically deter-mine the number of clusters and initial cluster centers,which improves the self-adaptability and stability of the algorithm.Then,considering that high-dimensional data often present a nonlinear structure,the manifold learning method is applied to construct a manifold spatial structure,which preserves the global geometric properties of complex high-dimensional data and improves the clustering effect of the algorithm on complex high-dimensional datasets.Fowlkes-Mallows Index(FMI),the weighted average of homogeneity and completeness(V-measure),Adjusted Mutual Information(AMI),and Adjusted Rand Index(ARI)are used as performance measures of clustering algorithms.The experimental results show that the manifold learning method is the superior distance measure,and the algorithm improves the clustering accuracy and performs superiorly in the clustering of low-dimensional and complex high-dimensional data.

The nature of electron density enhancement over a wide altitude range during ionosphere heating experiments at EISCAT

During the course of ionospheric heating experiments, researchers at the European Incoherent Scatter Scientific Association (EISCAT) observed an apparent electron density enhancement. The enhancement extended over a wide range of altitudes, above the reflection altitude of the high-frequency pump wave. However, whether this enhancement actually corresponds to a true enhancement in electron density remains an open question. When the dispersion relation of ion acoustic waves is followed, the frequency ratio of the enhanced ion line to the background ion line suggests that the profile of the effective ion mass may have remained unchanged. Furthermore, the solar radio flux and ion drift velocity indicate no significant changes in the ion species and their densities. In conclusion, the electron density enhancement observed at EISCAT should not, in fact, be considered a true enhancement.

Diagnosing ratio of electron density to collision frequency of plasma surrounding scaled model in a shock tube using low-frequency alternating magnetic field phase shift

A non-contact low-frequency(LF)method of diagnosing the plasma surrounding a scaled model in a shock tube is proposed.This method utilizes the phase shift occurring after the transmission of an LF alternating magnetic field through the plasma to directly measure the ratio of the plasma loop average electron density to collision frequency.An equivalent circuit model is used to analyze the relationship of the phase shift of the magnetic field component of LF electromagnetic waves with the plasma electron density and collision frequency.The applicable range of the LF method on a given plasma scale is analyzed.The upper diagnostic limit for the ratio of the electron density(unit:m^(-3))to collision frequency(unit:Hz)exceeds 1×10^(11),enabling an electron density to exceed 1×10^(20)m^(-3)and a collision frequency to be less than 1 GHz.In this work,the feasibility of using the LF phase shift to implement the plasma diagnosis is also assessed.Diagnosis experiments on shock tube equipment are conducted by using both the electrostatic probe method and LF method.By comparing the diagnostic results of the two methods,the inversion results are relatively consistent with each other,thereby preliminarily verifying the feasibility of the LF method.The ratio of the electron density to the collision frequency has a relatively uniform distribution during the plasma stabilization.The LF diagnostic path is a loop around the model,which is suitable for diagnosing the plasma that surrounds the model.Finally,the causes of diagnostic discrepancy between the two methods are analyzed.The proposed method provides a new avenue for diagnosing high-density enveloping plasma.