A neutral point potential drift control method for NPC three-level inverter

The output current harmonic distortion of a three-level inverter is less than the traditional twolevel inverter.The voltage stress of the semiconductor switch is low.A neutral point potential drift control method is proposed to solve the problem of the neutral point potential drift of the three-level inverter.The interaction mechanism between the neutral point potential and the space voltage vector is presented.The small vector output by the inverter is found to be the root cause of the midpoint potential drift.It is found that the fluctuation of the midpoint potential could be suppressed by increasing the capacitance value of the inverter bus voltage stabilizing capacitor.Furthermore,it inhibits the fluctuation of the midpoint potential.The experimental results verify the efficiency and precision of the proposed method.

A Study of DTC-Power Electronic Cascade Fed by Photovoltaic Cell-Three-Level NPC Inverter

This paper proposes a high performance three-level inverter Neutral Point Clamped (NPC) structure for photovoltaic system. The proposed configuration which can boost the low voltage of photovoltaic (PV) array, can also convert the photovoltaic DC power into high quality AC power. Attention has been paid to the problem of neutral point potential variation. In this way, a Direct Torque Control (DTC) technique has been applied and the estimated value of the Neutral Point Potential (NPP) is used, which is calculated by motor currents. This control strategy uses the redundancy presented by the inverter for selecting appropriate switching state through a switching table to achieve the control of NPP. This study shows the effect of the stability problem of the DC voltages and good static and dynamic performances were obtained in simulation of the proposed cascade “photovoltaic cell-three-level NPC VSI-induction motor”.

Model predictive current control for PMSM driven by three-level inverter based on fractional sliding mode speed observer

Based on the fractional order theory and sliding mode control theory,a model prediction current control(MPCC)strategy based on fractional observer is proposed for the permanent magnet synchronous motor(PMSM)driven by three-level inverter.Compared with the traditional sliding mode speed observer,the observer is very simple and eases to implement.Moreover,the observer reduces the ripple of the motor speed in high frequency range in an efficient way.To reduce the stator current ripple and improve the control performance of the torque and speed,the MPCC strategy is put forward,which can make PMSM MPCC system have better control performance,stronger robustness and good dynamic performance.The simulation results validate the feasibility and effectiveness of the proposed scheme.

An improved SVPWM control algorithm for three-level inverter

In the traditional three-level space vector pulse width modulation(SVPWM)algorithm,the sector judgment is computationallycomplex since the sector is divided into triangles and hexagons.In addition,the switching frequency is high becausethe seven-segment switching sequence is adopted.For this reason,a new SVPWM control algorithm for three-level inverteris proposed,in which the sector judgment is simplified by dividing the sector into quasi hexagons?and the new four-segmentswitching sequence is adopted to reduce the switching frequency.Simulation results show that the total harmonic distortiongrows down with the switching frequency decreasing,moreover,the algorithm runtime is also decreased.

Model predictive flux control of permanent magnet synchronous motor driven by three-level inverter based on fine-division strategy

Aiming at the difficulty of setting the weight coefficient in the value function of model predictive torque control(MPTC)for permanent magnet synchronous motor(PMSM)driven by three-level inverter,a fine-division model predictive flux control(MPFC)method is proposed.First,establish a mathematical model between the motor torque and the stator flux linkage according to the mathematical equations of PMSM.Thus,the control of the motor torque and stator flux linkage in the MPTC is transformed into the control of a single stator flux linkage vector,omitting the cumbersome weight setting process in the traditional MPTC.The midpoint potential control strategy is proposed,which uses the characteristics of redundant small vectors to balance the midpoint potential.After that,a fine-division strategy is proposed,which effectively reduces the number of candidate vectors and the computational burden of the system.Finally,the proposed MPFC is compared with MPTC by simulation.The results show that the proposed fine-division MPFC effectively reduces the system calculation,and has the advantages of simple principle and better dynamic and steady-state control performance.The feasibility of the control strategy is verified.

A Modified Neutral-point Voltage Control Strategy for Three-level Inverters Based on Decomposition of Space Vector Diagram

Capacitor voltage imbalance is a significant problem for three-level inverters.Due to the mid-point modulation of these inverter topologies,the neutral point potential moves up or down depending on the neutral point current direction creating imbalanced voltages among the two capacitors.This imbalanced capacitor voltage causes imbalanced voltage stress among the semiconductor devices and causes increase output voltage and current harmonics.This paper introduces a modified voltage balancing strategy using two-level space vector modulation.By decomposing the three-level space vector diagram into two-level space vector diagram and redistributing the dwell times of the two-level zero space vectors,the modified voltage balancing method ensures minimal NP voltage ripple.Compared to the commonly used NP voltage control method(using 3L SVM[9]),the proposed modified NP voltage control method offers a slightly higher neutral-point voltage ripple and output voltage harmonics but,it has much lower switching loss,code size and execution time.

Design and Implementation of a Three-Phase Active T-Type NPC Inverter for Low-Voltage Microgrids

This paper presents the design and implementation of a 3 kVA three-phase active T-type neutral-point clamped (NPC) inverter with GaN power devices for low-voltage microgrids. The designed inverter is used in a battery-based energy system (BESS) for power conversion optimization in applications to low-voltage microgrids. A modular design method has been developed for the design and implementation of the AT-NPC inverter. Experimental verification has been carried out based on a 3-kW three-phase T-Type NPC grid-connected inverter. FPGA based digital control technique has been developed for the current control of the three-level three-phase grid inverter. A maximum efficiency of 98.49% has been achieved within a load range from 50% to 75%.

Research of Wavelet Modulation for Single-Phase Three-Level Inverter

The single-phase three-level voltage source inverter based on wavelet modulation(WM) is proposed.The WM technique is based on constructing a nondyadic-type multi-resolution analysis(MRA),which supports sampling continuous-time sinusoidal signals in a nonuniform recurrent manner,and then reconstructing it by using inverter switching actions. In order to further improve the output voltage waveform and reduce harmonic distortion,the wavelet modulation is used to three-level inverter. The high magnitude of fundamental component and significantly reduced harmonic contents of the inverter output voltage can be achieved by using WM in the single-phase three-level voltage source inverter. Furthermore,the WM algorithm is implemented by using only one element government(EV) in DSP. The simulated and experimental results prove the accuracy and feasibility of the WM scheme for single-phase three-level voltage source inverter.

A neutral-point potential balance control strategy for three-level inverter based on VSVPWM

The topology of diode neutral-point-clamped(NPC)three-level inverter is prone to neutral-point potential offset.When the sum of three-phase current is zero,the virtual space vector pulse width modulation(VSVPWM)scheme does not cause the neutral-point voltage offset,but it lacks the ability to balance the deviation.For this reason,a neutral-point potential control strategy combining virtual space vector modulation and loop width control is proposed.The neutral-point potential is balanced by introducing the distribution factor for the regions with redundant vectors.For other regions,the potential is controlled by selecting a suitable switching sequence.Meanwhile,the effect on the virtual vector modulation is reduced within the loop width by setting an appropriate loop width,thereby improving the balance effect.The simulation results show that the proposed method has a strong ability to control the offset and has excellent potential balance performance under the conditions of balanced load,unbalanced load and asymmetric capacitance parameters.

Ride through Strategy for a Three-Level Dual Z-Source Inverter Using TRIAC

A new ride through strategy is introduced in a three-level dual Z-source inverter, for isolation under semiconductor switching failure condition. Here the output will have no significant decrease in the amplitude and quality. Instead of diodes, the triacs are added to the inverter source ends, as it can perform a bidirectional power transfer also it can operate well in both low and high voltage operating conditions. The faulted part can be isolated by simply altering the firing pulses for turning on/off the triacs using the carrier based SPWM technique and resulting in a boosting output with zero common mode voltage. Consequently, it forms a common floating point or null point with a zero common mode voltage. It is experimentally verified by using MATLAB, and digital oscilloscope.

Realization of a Nine-Level Cascaded NPC/H-Bridge PWM Inverter Using Phase-Shifted Carrier PWM Technique

Cascaded H-Bridge inverter has been researched for the past two decades, but there are no explicit guidelines on how one can realize a cascaded NPC （neutral-point-clamped）/H-Bridge inverter. Past research has also concentrated on realizing a five-level NPC/H-Bridge inverter. This fails to address the principle of realizing a general cascaded N-level NPC/H-Bridge PWM inverter. This paper proposes an improved topology for achieving a nine-level cascaded NPC （neutral-point-clamped） H-Bridge inverter with reduced harmonic content. This new proposed topology requires a lesser number of separate dc sources as compared to conventional cascaded H-Bridge inverter. The whole system is considered as having four three level legs having two positive and two negative legs. By properly phase shifting the modulating wave and carriers, a nine-level output is achieved. A theoretical harmonic analysis of the proposed inverter is carried out based on double Fourier principle. The theoretical results are verified through MATLAB simulation.

Three-level inverter configuration with common mode voltage elimination for induction motor drive (To continue)

The multiplicity of vector combinations for vectors of combined three-level inverters plays an important role, when deciding on the modulation scheme, to obtain minimum switching per inverter vector change, as described in the next Section. This is not possible with reduced common-mode three-level inverter structure, obtained with a five-level cascaded H-bridge configuration, as the space vectors locations do not exhibit multiplicity. Moreover, the proposed configuration requires only two power supplies, whereas the scheme with the five-level H-bridge configuration requires six isolated power supplies.

Three-level inverter configuration with common mode voltage elimination for induction motor drive

The multiplicity of vector combinations for vectors of combined three-level inverters plays an important role, when deciding on the modulation scheme, to obtain minimum switching per inverter vector change, as described in the next Section. This is not possible with reduced common-mode three-level inverter structure, obtained with a five-level cascaded H-bridge configuration, as the space vectors locations do not exhibit multiplicity. Moreover, the proposed configuration requires only two power supplies, whereas the scheme with the five-level H-bridge configuration requires six isolated power supplies.

基于SVPWM补偿优化的三电平NPC并网逆变器容错控制

为保证并网系统中三电平中点箝位(neutral point clamped,NPC)型并网逆变器单相桥臂短路或断路故障后持续运行,提出一种基于空间矢量脉宽调制(space vector pulse width modulation,SVPWM)的优化补偿型低共模电压容错控制策略。首先,通过分析故障后八开关三相逆变器(eight switch three phase inverters,ESTPI)拓扑开关状态对应的共模电压大小,确定参考电压矢量合成规则;然后,通过一个基波周期内中点电流情况分析中点电位波动机理,进而对空间矢量合成进行调节补偿;最后,设计低通滤波器和滞环控制器进一步对补偿进行优化调整,保证并网电流质量的同时有效抑制了直流母线中点电位偏移。仿真结果表明,该容错控制策略能够实现三电平NPC并网逆变器单相桥臂故障后并网系统的稳定可靠运行,每个基波周期有三分之一时间的共模电压得到改善,优化补偿后的并网电流质量显著提高,且在并网电流突变时具备良好的控制特性。

基于T-NPC型三电平逆变器的控制策略研究

T-NPC三电平逆变器作为中高功率发电领域应用极为广泛的拓扑,对提高电能转换效率起到极大促进作用。研究了基于T-NPC三电平逆变器的新型PET拓扑结构,该拓扑结构将传统变压器的两电平逆变器替换为T-NPC结构的三电平逆变器,以进一步减少谐波、降低损耗。MATLAB/Simulink仿真实验验证了T-NPC型三电平结构控制策略的可行性和有效性。

NPC三电平并网逆变器共模电流抑制技术研究

共模电流抑制是非隔离型光伏并网逆变器的一个关键技术问题。首先基于考虑所有寄生参数的非隔离型单相并网逆变器高频共模等效模型归纳出两种抑制漏电流的途径,并将其应用到二极管钳位(neutral point clamped,NPC)三电平并网逆变器中得出仅通过正弦脉宽调制(sine pulse width modulation,SPWM)策略抑制共模电压不可行和通过电路元件参数匹配抑制共模电压的3种可能方案。针对3种可能的方案分析了它们的成立条件和现实可行性,并通过相应的实验验证结论的可靠性。其中,提出的通过补偿电容来弥补寄生参数差异的措施可以进一步增强NPC三电平并网逆变器漏电流抑制性能,是一种简单、可靠、有效的实用技术。

基于独立量分析的NPC光伏逆变器故障诊断

功率开关器件是逆变器的核心部件,功率开关器件的故障诊断对逆变器的可靠运行意义重大,而功率开关器件故障特征提取技术是实现其故障诊断的技术基础。分析三电平逆变器中常见的功率开关器件开路故障,将故障类型分成典型故障与非典型故障两大类。对于非典型故障应用基于独立量分析的稀疏编码算法对逆变器输出相电压信号进行故障特征提取,并采用BP神经网络的分类器对非典型故障进行诊断。通过仿真验证其可行性,故障诊断准确率达到95%,并通过与小波分析及主元分析的特征提取算法的对比试验,说明独立量分析算法的在逆变器开关器件开路故障特征提取应用的合理性和优越性。

NPC三电平逆变器容错拓扑及其控制研究

研究了二极管中点钳位(Neutral point clamped,NPC)三电平逆变器的容错拓扑及其控制问题,以保证NPC逆变器在发生器件故障时,仍然能够继续工作。在基本的NPC逆变器中增加一个不对称桥臂,并将其中点用双向可控开关连接到每相负载。为消除输出相电压的低次谐波含量,该桥臂采用SPWM控制方法代替传统的方波控制方法。当检测到NPC逆变器某相器件出现故障时,控制双向可控开关将故障相的负载连接到新加入的不对称桥臂中点。与以前文献提出的容错拓扑相比,在获得相同效果的情况下,提出的拓扑具有使用器件及其驱动电路数量少、电路成本低等优势。仿真和实验结果表明,所提出的NPC逆变器容错拓扑能够在容错控制后保持三相平衡工作,同时不降低原电路的输出功率,电路的可靠性得到很大提高。

基于新型SVPWM的NPC/H桥五电平逆变器共模电压抑制策略研究

为解决逆变器中共模电压随其电平数增加而幅值增大的问题,以中点箝位H桥五电平逆变器为例,分析共模电压的产生机理,并提出一种基于参考电压矢量分解的新型五电平空间矢量脉冲宽度调制(SVPWM)算法。该算法直接将五电平分解为两电平,避免了先将五电平转化为三电平,再将三电平转化为两电平的繁琐过程且可适用于更高电平。基于该算法设计了一种通过合理选择空间矢量来抑制共模电压的五段式调制方法。理论分析、仿真与实验结果表明,该方法可以将共模电压最大值抑制到单相直流电压源电压值的1/3,比传统SVPWM算法下降了60%;同时,逆变器的开关损耗也得到了减小。

一种抑制NPC逆变器共模电压的新方法

提出一种用集成共模电抗器抑制逆变器产生的共模电压的方法,介绍了电路的拓扑、NPC逆变器和共模电抗器的结构和工作原理。仿真结果表明这种电路抑制共模电压的效果好,可以消除95%以上的共模电压,同时差模电压的变化率dv/dt也变得很小。