The dependences of the power loss per cycle on frequency have been investigated in the ranges of 100 Hz<= f<=25000 Hz and 0.1 T< =Bm <=1.0 T for three main original magnetic states in five sorts of Fe-base...The dependences of the power loss per cycle on frequency have been investigated in the ranges of 100 Hz<= f<=25000 Hz and 0.1 T< =Bm <=1.0 T for three main original magnetic states in five sorts of Fe-based nanocrystalline soft magnetic alloys. The measured and calculated results showed that the total power loss per cycle clearly exhibited a nonlinear behavior in the range below 3 kHz～5 kHz depending on both the magnetic state and the value of Dm, whereas it showed a quasi-linear behavior above this range. The total loss was decomposed into hysteresis loss, classical eddy current loss and excess loss, the obvious nonlinear behavior has been confirmed to be completely determined by the dependence of the excess loss on frequency. It has been indicated that the change rate of the excess loss per cycle with respect to frequency sharp decreases with increasing frequency in the range below about 3 kHz～5 kHz, wherease the rate of change slowly varies above this range, thus leading to the quasilinear behavior of the total loss per cycle. In this paper, some linear expressions of the total loss per cycle has been given in a wider medium-frequency segment, which can be used for roughly estimating the total loss.展开更多
Fe73. 5 Cu1 Nb3 Si15.5B7 nanocrystalline powder cores with different particle sizes ranging from 10 to 125 9m were fabricated by cold-pressing techniques. The cores exhibited increased core loss P cv and decreased ini...Fe73. 5 Cu1 Nb3 Si15.5B7 nanocrystalline powder cores with different particle sizes ranging from 10 to 125 9m were fabricated by cold-pressing techniques. The cores exhibited increased core loss P cv and decreased initial permea- bility μi with addition of fine powders below 50 μm in size, and the content should be less than 40 mass%. It was thought to be closely related to the high coercive force H c due to the stresses generated during the crushing process and high demagnetization fields of small powders. Furthermore, modifying the alloy compositions by adding defined amount of Ni could improve the soft magnetic properties, including superior characteristics of permeability under high direct current （DC） bias field and comparable low core loss at high frequency.展开更多
文摘The dependences of the power loss per cycle on frequency have been investigated in the ranges of 100 Hz<= f<=25000 Hz and 0.1 T< =Bm <=1.0 T for three main original magnetic states in five sorts of Fe-based nanocrystalline soft magnetic alloys. The measured and calculated results showed that the total power loss per cycle clearly exhibited a nonlinear behavior in the range below 3 kHz～5 kHz depending on both the magnetic state and the value of Dm, whereas it showed a quasi-linear behavior above this range. The total loss was decomposed into hysteresis loss, classical eddy current loss and excess loss, the obvious nonlinear behavior has been confirmed to be completely determined by the dependence of the excess loss on frequency. It has been indicated that the change rate of the excess loss per cycle with respect to frequency sharp decreases with increasing frequency in the range below about 3 kHz～5 kHz, wherease the rate of change slowly varies above this range, thus leading to the quasilinear behavior of the total loss per cycle. In this paper, some linear expressions of the total loss per cycle has been given in a wider medium-frequency segment, which can be used for roughly estimating the total loss.
基金Sponsored by National High-tech Research and Development Program(863 Program)of China(2013AA030802)
文摘Fe73. 5 Cu1 Nb3 Si15.5B7 nanocrystalline powder cores with different particle sizes ranging from 10 to 125 9m were fabricated by cold-pressing techniques. The cores exhibited increased core loss P cv and decreased initial permea- bility μi with addition of fine powders below 50 μm in size, and the content should be less than 40 mass%. It was thought to be closely related to the high coercive force H c due to the stresses generated during the crushing process and high demagnetization fields of small powders. Furthermore, modifying the alloy compositions by adding defined amount of Ni could improve the soft magnetic properties, including superior characteristics of permeability under high direct current （DC） bias field and comparable low core loss at high frequency.
