Influence of different cooling rates on the microstructure and the precipitation behavior of Nb-Ti microalloyed steel was investigated by CSLM, OM, SEM and EDS. The results show that the precipitation process of carbo...Influence of different cooling rates on the microstructure and the precipitation behavior of Nb-Ti microalloyed steel was investigated by CSLM, OM, SEM and EDS. The results show that the precipitation process of carbonitrides can be in-situ observed by CSLM, and with the increase of the cooling rate, the distribution of precipitates changes from along the austenitic grain boundaries to within the grains. With the increase of the cooling rate, the proeutectoid ferritic film becomes smaller and smaller and then disappears, and the original austenitic grains become finer and finer. In order to obtain non-film like proeutectoid ferrites or non-chain like precipitates along the austenitic grain boundaries and finer austenitic grains,the cooling rate should be at least 5℃/s.展开更多
The dynamic recrystallization （DRX） behavior of Nb-Ti microalloyed steels was investigated by isothermal single compression tests in the temperature range of 900-1 150 ℃ at constant strain rates of 0.1-5 s^-1. DRX ...The dynamic recrystallization （DRX） behavior of Nb-Ti microalloyed steels was investigated by isothermal single compression tests in the temperature range of 900-1 150 ℃ at constant strain rates of 0.1-5 s^-1. DRX was retarded effectively at low temperature due to the onset of dynamic precipitation of Nb and Ti carbonitrides, resulting in higher values of the peak strain. An expression was developed for the activation energy of deformation as a function of the contents of Nb and Ti in solution as well as other alloying elements. A new value of corrective factor was determined and applied to quantify the retardation produced by increase in the amount of Nb and Ti dissolved at the reheating temperature. The ratio of critical strain to peak strain decreases with increasing equivalent Nb content. In addition, the effects of Ti content and deformation conditions on DRX kinetics and steady state grain size were determined. Finally, the kinetics of dynamic precipitation was determined and effect of dynamic precipitation on the onset of DRX was clarified based on the comparison between precipitate pinning force and recrystallization driving force.展开更多
Hot ductility of the Nb- and Ti-containing line-pipe steel CC slab specimens were measured under the sirain rate of 1 x 10-3/s. Three types of precipitates were found in the fractured specimens. One was the block-shap...Hot ductility of the Nb- and Ti-containing line-pipe steel CC slab specimens were measured under the sirain rate of 1 x 10-3/s. Three types of precipitates were found in the fractured specimens. One was the block-shaped coarse TiN particles precipitated at high temperature. Another type was the fine dynamic precipitation products precipitated at 950～900℃ which caused remarkable ductility reduction of the steel. The third type was the co-existed precipitates formed by fine Nb precipitates nucleating and growing on TiN paricles. Compared with Nb-containing steel which contains no Ti, there was no ductility drop for Nb- and Ti-containing steel at temperature between 850℃ and Ar3 and, the γ→α transformation inside the grain matrixes proceeded faster, which both improved the ductility of the steel in the low ductility temperature Region Ⅲ.展开更多
The nanometer-size carbides formed in ferrite matrix of Nb-Ti microalloyed steel at different finishing cooling temperatures and holding time have been investigated. The characteristics of nanometer-size carbides in f...The nanometer-size carbides formed in ferrite matrix of Nb-Ti microalloyed steel at different finishing cooling temperatures and holding time have been investigated. The characteristics of nanometer-size carbides in ferrite were observed by transmission electron microscopy, and mechanical properties of ferrite were detected by a nano-hardness tester. The results showed that interphase precipitation and diffusion precipitation were observed at different finishing cooling temperatures, and the interphase precipitation was planar and curved. Sheet spacing of inter-phase precipitation increased with the increase of finishing cooling temperature and changed a little when holding for 50--1000 s. Interphase precipitation shows higher nano-hardness at 640℃ compared with diffusion precipitation at 600℃, and the contribution of interphase precipitation to the mechanical properties of ferrite was larger than that of diffusion precipitation.展开更多
文摘Influence of different cooling rates on the microstructure and the precipitation behavior of Nb-Ti microalloyed steel was investigated by CSLM, OM, SEM and EDS. The results show that the precipitation process of carbonitrides can be in-situ observed by CSLM, and with the increase of the cooling rate, the distribution of precipitates changes from along the austenitic grain boundaries to within the grains. With the increase of the cooling rate, the proeutectoid ferritic film becomes smaller and smaller and then disappears, and the original austenitic grains become finer and finer. In order to obtain non-film like proeutectoid ferrites or non-chain like precipitates along the austenitic grain boundaries and finer austenitic grains,the cooling rate should be at least 5℃/s.
基金the National Natural Science Foundation of China(No.50474086,50334010)the Program for New Century Excellent Talents in Universities(No.NCET-04-0278)of the Ministry of Education
文摘The dynamic recrystallization （DRX） behavior of Nb-Ti microalloyed steels was investigated by isothermal single compression tests in the temperature range of 900-1 150 ℃ at constant strain rates of 0.1-5 s^-1. DRX was retarded effectively at low temperature due to the onset of dynamic precipitation of Nb and Ti carbonitrides, resulting in higher values of the peak strain. An expression was developed for the activation energy of deformation as a function of the contents of Nb and Ti in solution as well as other alloying elements. A new value of corrective factor was determined and applied to quantify the retardation produced by increase in the amount of Nb and Ti dissolved at the reheating temperature. The ratio of critical strain to peak strain decreases with increasing equivalent Nb content. In addition, the effects of Ti content and deformation conditions on DRX kinetics and steady state grain size were determined. Finally, the kinetics of dynamic precipitation was determined and effect of dynamic precipitation on the onset of DRX was clarified based on the comparison between precipitate pinning force and recrystallization driving force.
文摘Hot ductility of the Nb- and Ti-containing line-pipe steel CC slab specimens were measured under the sirain rate of 1 x 10-3/s. Three types of precipitates were found in the fractured specimens. One was the block-shaped coarse TiN particles precipitated at high temperature. Another type was the fine dynamic precipitation products precipitated at 950～900℃ which caused remarkable ductility reduction of the steel. The third type was the co-existed precipitates formed by fine Nb precipitates nucleating and growing on TiN paricles. Compared with Nb-containing steel which contains no Ti, there was no ductility drop for Nb- and Ti-containing steel at temperature between 850℃ and Ar3 and, the γ→α transformation inside the grain matrixes proceeded faster, which both improved the ductility of the steel in the low ductility temperature Region Ⅲ.
基金Item Sponsored by National Natural Science Foundation of China(51104046)Fundamental Research Funds for Central Universities of China(N120407001,N120807001)
文摘The nanometer-size carbides formed in ferrite matrix of Nb-Ti microalloyed steel at different finishing cooling temperatures and holding time have been investigated. The characteristics of nanometer-size carbides in ferrite were observed by transmission electron microscopy, and mechanical properties of ferrite were detected by a nano-hardness tester. The results showed that interphase precipitation and diffusion precipitation were observed at different finishing cooling temperatures, and the interphase precipitation was planar and curved. Sheet spacing of inter-phase precipitation increased with the increase of finishing cooling temperature and changed a little when holding for 50--1000 s. Interphase precipitation shows higher nano-hardness at 640℃ compared with diffusion precipitation at 600℃, and the contribution of interphase precipitation to the mechanical properties of ferrite was larger than that of diffusion precipitation.
