A Novel High Output Resistance Current Source Based on Negative Resistance

This paper presents a novel scheme for enhancing resistance that utilizes an equivalent negative resistance. Adopting this novel scheme in the proposed current source could remarkably boost its output resistance without requiring increased power supply. Simulation with 0.6μm CMOS process models shows that the output resistance of the novel current source can reach the order of 10^9Ω with a 1.04GHz bandwidth and only 10.6ppm/℃ in the range of -40～145℃.

The characteristics of negative corona discharge and radio interference at different altitudes based on coaxial wire-cylinder gap

The corona discharge from transmission lines in high-altitude areas is more severe than at lower altitudes. The radio interference caused thereby is a key factor to be considered when designing transmission lines. To study the influence of altitude on negative corona characteristics, an experimental platform comprising a movable small corona cage was established: experiments were conducted at four altitudes in the range of 1120-4320 m, and data on the corona current pulse and radio interference level of 0.8-mm diameter fine copper wire under different negative voltages were collected. The experimental results show that the average amplitude, repetition frequency and average current of the corona current pulse increase with increasing altitude. The dispersion of pulse amplitude increases with increase in altitude, while the randomness of the pulse interval decreases continuously. Taking the average current as an intermediate variable,the relationship between radio interference level and altitude is obtained. The result of this research has some significance for understanding the corona discharge characteristics of ultra-highvoltage lines.

A Possible Minimum Toy Model with Negative Differential Capacitance for Self-sustained Current Oscillation

We generalize a simple model for superlattices to include the effect of differential capacitance. It is shown that the model always has a stable steady-state solution （SSS） if all differential capacitances are positive. On the other hand, when negative differential capacitance is included, the model can have no stable SSS and be in a self-sustained current oscillation behavior. Therefore, we find a possible minimum toy model with both negative differential resistance and negative differential capacitance which can include the phenomena of both self-sustained current oscillation and I-V oscillation of stable SSSs.

Current Reversal and Negative Conductance for a Super-Conducting Junctions Device

In the paper, we study a super-conducting junctions device subject to an input periodic signal and a constant force. It is shown that, for this device, we can get current reversals for the current of the electron pairs versus the frequency of the periodic signal and negative conductance for the current of the electron pairs as a function of the constant force.

Current loss of magnetically insulated coaxial diode with cathode negative ion

Current loss without an obvious impedance collapse in the magnetically insulated coaxial diode （MICD） is studied through experiment and particle-in-cell （PIC） simulation when the guiding magnetic field is strong enough. Cathode nega- tive ions are clarified to be the predominant reason for it. Theoretical analysis and simulation both indicate that the velocity of the negative ion reaches up to 1 cm/ns due to the space potential between the anode and cathode gap （A-C gap）. Accord- ingly, instead of the reverse current loss and the parasitic current loss, the negative ion loss appears during the whole pulse. The negative ion current loss is determined by its ionization production rate. It increases with diode voltage increasing. The smaller space charge effect caused by the beam thickening and the weaker radial restriction both promote the negative ion production under a lower magnetic field. Therefore, as the magnetic field increases, the current loss gradually decreases until the beam thickening nearly stops.

Reassessment of Permissible Negative Sequence Current for Power Plant Operation of Taipower

The N3 power plant of Taipower is located in the southern tip of Taiwan and connected to the power pool by four out-linking 345-kV overhead transmission circuits. There are two 951-MW generators. Each generator occupied 11% of the system peak load in 1985 when the generator was in commercial operation. Since Taipower is an isolated system, at the N-2 conditions, those generators were reduced to 75% loading to protect the power system. By the way, to avoid damage of negative sequence current (NSC), the limits of the N3 power plant are stricter than those in the IEEE Standard. However, in 2010, the capacity ratio of each generator in the plant to the system peak load has been reduced to 3% only. To increase the economic benefit of those generators, it is required to reassess the operation limits of NSC. EMTP was used to calculate the levels of NSC from the out-linking transmission circuits. From the results of this study, the effects of NSC could be ignored when the four out-linking circuits are in N-0, N-1, and N-2 conditions. The generators can be operated in full loading under these conditions. The modifications to the NSC limits of the N3 power plant are also suggested.

The current pulses characteristics of the negative corona discharge in SF_(6)/CF_(4)mixtures

This paper presents the results of numerical investigation of the current pulses characteristics in SF_(6)/CF_(4)mixtures for the negative point-plane corona discharge.The pressure and the temperature of gas mixtures are 0.4 MPa and 300 K,respectively.The CF_(4)content varies from20%to 80%.The 2D axisymmetric geometry with point-plane electrodes is investigated,and the three drift-diffusion equations are solved to predict the characteristics of the negative corona discharge.In addition,Poisson’s equation is coupled with the above three continuity equations to calculate the electric field.In order to calculate the electron impact coefficients,including the Townsend ionization and attachment coefficients,as well as the mobilities and diffusion coefficients for electrons,the two-term Boltzmann equation is solved.The characteristics of three ionic species at five stages of the first current pulse in 60%SF_(6)-40%CF_(4)and20%SF_(6)-80%CF_(4)mixtures are selected to discuss the development mechanism of current pulses.Moreover,the reduced electric field strengths at the corresponding time instants are presented to help understand the discharge process.The current waveform and the total number of three species are compared in all the cases to analyze the effects of the CF_(4)content on the discharge.The reduced electric field strength is also helpful in understanding the effects of CF_(4)content.When the CF_(4)content increases to 80%,the discharge is more intensive and the pulse frequency also increases.

Effects of temperature and discharge parameters on ozone concentration of negative corona discharge

The relationship of the ozone generation and the heating power, corona wire surface temperature, discharge electrode and netting electrode was studied during the negative corona discharge. The experimental results showed that the ozone concentration reduced with applied voltage decrease. With heating power increase, the ozone concentration of unit current decreased at exponential rate and it almost change no longer over 0.40 W. Under given temperature, the lower the applied voltage was, the smaller the ozone concentration was; while under given applied voltages, only over 11 kV could decrease with the surface temperature increase. The ozone concentration decreased with the lengthening of corona wire, and could reduced to 10 ppb under experimental condition of 14.2 kV; it also decreased with the shortening of wire diameter, and could decrease 67% at best in the given condition. Moreover, it decreased with the increasing size of netting electrode mesh. At the anion current of 1.65 μΑ, the ozone concentration of 5.0×5.0 cm 2 is only 41% of that of 3.3×3.3 cm 2.

Bioinspired polydopamine coated nanopore nanofluidic unijunction transistor exhibiting negative differential resistance and ion current oscillation

Nanofluidic devices have turned out to be exemplary systems for investigating fluidic transport properties in a highly restricted area, where the electrostatic interactions or chemical reactions between nanochannel and flowing species strongly dominate the ions and flow transport. Numerous nanofluidic devices have recently been explored to manipulate ion currents and construct electronic devices. Enlightened by electronic field effect transistors, utilizing the electric field effect of nanopore nanochannels has also been adopted to develop versatile nanofluidic devices. Here, we report a nanopore-based nanofluidic unijunction transistor composed of a conical glass nanopipette with the biomaterial polydopamine (PDA) coated at its outer surface. The asfabricated nanofluidic device exhibited negative differential resistance (NDR) and ion current oscillation (ICO) in ionic transport. The pre-doped copper ions in the PDA moved toward the tip as increasing the potential, having a robust shielding effect on the charge of the tip, thus affecting the surface charge density of the nanopore in the working zone. Finite element simulation based on a continuum model coupled with Stokes-Brinkman and Poisson-Nernst-Planck (PNP) equations revealed that the fluctuations in charge density remarkably affect the transport of ionic current in the nanofluidic device. The as-prepared nanofluidic semiconductor device was a ready-to-use equipment that required no additional external conditions. Our work provides a versatile and convenient way to construct nanofluidic electronic components;we believe by taking advantage of advanced surface modification methods, the oscillation frequency of the unijunction transistors could be controlled on demand, and more nanofluidic devices with resourceful functions would be exploited.

Improved Ladder Wave Modulation of Circulating Current Suppressing Control Strategy of MMC

This paper partitions the arm current of MMC into uncontrollable current and controllable current. The former is determined by the load that can’t be controlled by taking any control strategy. The later caused by the unbalanced total inserted voltage of three arms can be controlled by some improved algorithms. The conclusion based on the researching the essence of circulating current is reached that change the number of the inserted sub-modules in each phase can suppress the circulating current. Combined with the improved ladder wave modulation, a novel circulating current suppression strategy particularly for the inverter station is developed. The improved strategy can adapt to load changes and reduce the circulating current and output voltage THD of MMC ac terminals greatly without increasing any peripheral circuits. Finally, the simulation model of 100 submodules in each phase is constructed in MATLAB and the simulation results verify the correctness and effectiveness of the modified control algorithm.

A High Dynamic Range GMI Current Sensor

The design and performances of a high dynamic range DC-AC current sensor utilizing Giant Magneto-Impedance (GMI) are presented. The sensor is based on a GMI element with negative feedback. The sensing element is a 30 μm diameter GMI Co-based amorphous wire. It is curled to a toroidal core of 2 cm diameter. A bias magnetic field of about 650 A/m is applied to the GMI element to obtain an asymmetric GMI effect. A strong negative feedback is introduced to ensure linearity in a wide dynamic range. Analog conditioning electronics was fully developed. This includes a square wave oscillator based on an inverter trigger;a peak detector and a high gain amplifier with zero adjust. The GMI element is driven at a 3 MHz frequency and 5 mA peak-to-peak current. The closed-loop operations are investigated and the performances of the sensor are presented. DC current measurements are performed. The sensor exhibits good sensitivity and very good linearity, free from hysteresis, in a wide dynamic range of ±40 A. The sensitivity is about 0.24 V/A and the linearity error is about 0.02% of the full scale (FS). The hysteresis error is smaller than the measurement accuracy. AC current measurements using the developed sensor have also been successfully achieved. The sensor bandwidth in closed-loop was about 1.7 kHz.

Generation of adjustable pure spin currents in negative-U systems

Single-particle sequential tunneling is studied through a negative-U center hybridized with a superconducting, a ferromagnetic, and a normal metal electrodes. In stark contrast to the case of positive U, the single-particle tunneling in attractive charging energy is usually prohibited by ground states with electrons in pairs. We find a microscopic mechanism to induce single-particle sates from pair states. As a consequence, in the nonpolarized metal terminal a remarkable pure spin current with no charge currents survives over a wide range of gate- and bias- voltages, which is rather crucial for experimental observation and design of spintronic devices. In addition, a significant spin-filter effect is presented in certain bias regime.

论李伯元对科举制度的否定及其对选官制度的探索

考察李伯元的《官场现形记》《中国现在记》《文明小史》,我们可以看出李伯元认为科举制度对应试者的道德衡量没有保障、以"四书五经"为基础的八股文考试空疏无用,否定集权的考官制度,这些否定性的科举观念是对清代小说家科举观的总结。在此基础上,他预感科举即将废除,对科举改革表示赞赏、对改革的弊端提出了批评,还对选官制度进行了积极探索。究其原因,对考官不满的心理动机、拯时济世的热切愿望、科举将废的时代潮流是促使他在小说中否定科举、探索新制的几个重要因素。

凝结水泵进空气事故特例分析

以600MW亚临界火电机组的立式长轴凝结水泵作为研究对象,通过对水泵汽蚀和水泵进空气2种事故的原因、异同点的介绍和对比,并结合凝结水泵的具体汽蚀事故特例,较为详细的分析了系统运行中突发异常和备用泵检修导致凝结水泵进空气事故的原因。提出了比较现实可行的防范措施和处理方法。

否定自然辩证法的后果——卢卡奇总体性辩证法探析的一个维度

卢卡奇在《历史与阶级意识》中试图阐述一种正统马克思主义,他自己也努力想成为正统马克思主义者。但是,结果却并没有获得成功,反而偏离了马克思主义。究其原因可能很多,但是最为根本的一点,在于他主张的总体性辩证法否定自然辩证法。而否定自然辩证法主要会导致三个后果:一是致使他的总体性辩证法失去物质基础,成为"空中楼阁";二是在认识论上批判反映论,反映论因此成为他批判的"靶子";三是他宣称通过总体性辩证法要实现的"当前目标"和"最终目标"都成为幻影,对于他而言,改变世界只是"神话"。

反馈类型的判断方法

反馈类型的判断和引入是电路分析和设计的重点和难点，本文就各种反馈类型的判断方法进行了详细的阐述。

Modeling and Analysis of Novel Integrated Radial Hybrid Magnetic Bearing for Magnetic Bearing Reaction Wheel

Conventional ball bearing reaction wheel used to control the attitude of spacecraft can＇t absorb the centrifugal force caused by imbalance of the wheel rotor,and there will be a torque spike at zero speed,which seriously influences the accuracy and stability of spacecraft attitude control.Compared with traditional ball-bearing wheel,noncontact and no lubrication are the remarkable features of the magnetic bearing reaction wheel,and which can solve the high precision problems of wheel.In general,two radial magnetic bearings are needed in magnetic bearing wheel,and the design results in a relatively large axial dimension and smaller momentum-to-mass ratios.In this paper,a new type of magnetic bearing reaction wheel（MBRW） is introduced for satellite attitude control,and a novel integrated radial hybrid magnetic bearing（RHMB） with permanent magnet bias is designed to reduce the mass and minimize the size of the MBRW,etc.The equivalent magnetic circuit model for the RHMB is presented and a solution is found.The stiffness model is also presented,including current stiffness,position negative stiffness,as well as tilting current stiffness,tilting angular position negative stiffness,force and moment equilibrium equations.The design parameters of the RHMB are given according to the requirement of the MBRW with angular momentum of 30 N ？ m ？ s when the rotation speed of rotor reaches to 5 kr/min.The nonlinearity of the RHMB is shown by using the characteristic curves of force-control current-position,current stiffness,position stiffness,moment-control current-angular displacement,tilting current stiffness and tilting angular position stiffness considering all the rotor position within the clearance space and the control current.The proposed research ensures the performance of the radial magnetic bearing with permanent magnet bias,and provides theory basis for design of the magnetic bearing wheel.

Effects of Voltage Sag on the Performance of Induction Motor Based on a New Transient Sequence Component Method

Voltage sag is one of the most common power quality disturbances in industry,which causes huge inrush currents in stator windings of induction motors,and adversely impacts the motor secure operation.This paper firstly introduces a 2D Time-Stepping multi-slice finite element method(2D T-S multi-slice FEM)which is used for calculating the magnetic field distribution in induction motors under different sag events.Then the paper deduces the transient analytical expression of stator inrush current based on the classical theory of AC motors and presents a separation method for the positive,negative and zero sequence values based on instantaneous currents.With this method,the paper studies the influences of voltage sag amplitude,phase-angle jump and initial phase angle on the stator positive-and negative-sequence peak currents of 5.5 kW and 55 kW induction motors.This paper further proposes a motor protection method under voltage sag condition with the stator negative-sequence peak currents as the protection threshold,so that the protection false trip can be avoided effectively.Finally,the calculation and analysis results are validated by the comparison of calculated and measured stator peak value of the 5.5 kW induction motor.

Intelligent power factor compensation equipment of three phase low voltage loads

An intelligent power factor correction scheme is presented for three phase low power factor loads. This new scheme is able to perform individual phase sensing of parameters by monitoring at all times to sense a change in system parameters and affects individual phase correction by applying the exact amount of reactive components needed for each phase, and can also reduce negative sequence current caused by the load to improve system balance. An optimization criterion is used for the proper calculation of reactive power steps in a power compensation installation of capacitor banks. The criterion is enabled by sampling measurements performed on the electrical plant examined within specific interval of time.

Design of DSTATCOM Controller for Compensating Unbalances

In a three phase power system, the voltages at the generation side are in sinusoidal and equal in magnitude with 120? phase difference between the phases. However, at the load side voltages may become unbalanced due to unequal voltage magnitudes at the fundamental frequency, phase angle deviations or unequal distribution of single phase loads. The voltage unbalance is a major power quality issue, because a small unbalance in the phase voltages can cause a larger unbalance in the phase currents. A completely balanced three-phase three wire system contains only positive sequence components of voltage, current and impedance, whereas unbalanced system contains both positive and negative sequence components of voltages and currents. The negative sequence component of current in the unbalanced system increases the temperature and losses in the equipments. Hence, it is necessary to mitigate this problem by supplying the negative sequence current to the load at the load side and keep the source side balanced. This paper proposes the shunt connected, current injecting Distribution Static Synchronous Compensator (DSTATCOM) with appropriate controller to mitigate the unbalanced load current. The symmetrical components based Hysteresis Current Controller (HCC) is designed for DSTATCOM to diminish the unbalances in a three-phase three-wire system. The performance of the controller is studied by simulating the entire system in the MATLAB/Simulink environment. The DSTATCOM with HCC is found to be better than other controllers because it is suitable for compensating both balanced and unbalanced loads.