A new universal multiple input multiple output (MIMO) type current-mode biquad employing two dual output current conveyors (DOCCII), one multiple output current controlled current amplifier (MOCCCA) and four passive g...A new universal multiple input multiple output (MIMO) type current-mode biquad employing two dual output current conveyors (DOCCII), one multiple output current controlled current amplifier (MOCCCA) and four passive grounded elements is proposed which can realize all the five basic filtering functions namely, low-pass (LP), high-pass (HP), band-pass (BP), band-stop (BR) and all-pass (AP) in current mode from the same configuration. The centre frequency can be set by the passive elements of the circuit and the quality factor Q0 is electronically tunable through bias currents of the MOCCCA. Therefore, the biquad filter has independent tenability for the and Q0. The active and passive sensitivities of Q0 and are low. The workability of the new configuration has been demonstrated by PSPICE simulation results based upon a CMOS CCII in0.35μm technology.展开更多
This paper studied a snow event over North China on 21 February 2017,using aircraft in-situ data,a Lagrangian analysis tool,and WRF simulations with different microphysical schemes to investigate the supercooled layer...This paper studied a snow event over North China on 21 February 2017,using aircraft in-situ data,a Lagrangian analysis tool,and WRF simulations with different microphysical schemes to investigate the supercooled layer of warm conveyor belts(WCBs).Based on the aircraft data,we found a fine vertical structure within clouds in the WCB and highlighted a 1-2 km thin supercooled liquid water layer with a maximum Liquid Water Content(LWC) exceeding0.5 g kg^(-1) during the vertical aircraft observation.Although the main features of thermodynamic profiles were essentially captured by both modeling schemes,the microphysical quantities exhibited large diversity with different microphysics schemes.The conventional Morrison two-moment scheme showed remarkable agreement with in-situ observations,both in terms of the thermodynamic structure and the supercooled liquid water layer.However,the microphysical structure of the WCB clouds,in terms of LWC and IWC,was not apparent in HUJI fast bin scheme.To reduce such uncertainty,future work may focus on improving the representation of microphysics in bin schemes with in-situ data and using similar assumptions for all schemes to isolate the impact of physics.展开更多
The State Council, or China＇s cabinet, has called for a middle to long-term plan to pro- mote new-style urbanization, enabling more migrant workers and their families to settle in cities.
The oil film clutch, which is superior in speed adjustment, is capable of being used in the belt conveyor to carry out soft start operation. According to running properties of both belt conveyor and oil film clutch...The oil film clutch, which is superior in speed adjustment, is capable of being used in the belt conveyor to carry out soft start operation. According to running properties of both belt conveyor and oil film clutch, equations that are used to decide the lubricating oil flow and the number of oil films (i.e. the number of rotating and stationary plates) are deduced theoretically. Also key parameters are provided for the design of the hydraulic system. All these together provide the theoretical basis for the soft start design of the belt conveyor and references for the application of the oil film clutch in similar fields.展开更多
The key technology of semi-continuous conveyor system decides the successful using of this system. The key technology includes optimal initial building depth of this system,the crusher moving step and the layout of co...The key technology of semi-continuous conveyor system decides the successful using of this system. The key technology includes optimal initial building depth of this system,the crusher moving step and the layout of conveyor system are studied, and their calculating models are built up.展开更多
Considering the control difficulties of a hydro-viscous trol algorithm was derived. A fuzzy-immune PID controller was soft start （HVSS） device of a belt conveyor, a fuzzy-immune con- designed based on immune feedbac...Considering the control difficulties of a hydro-viscous trol algorithm was derived. A fuzzy-immune PID controller was soft start （HVSS） device of a belt conveyor, a fuzzy-immune con- designed based on immune feedback regulations and adaptability of the fuzzy logic inference. Using MATLAB software, we simulated the controller and compared the HVSS device with a conven- tional PID controller and a fuzzy PID controller. The simulation results show that the controller is not only very reliable as a PID controller, robust and requires only a short adjustment time of fuzzy control, but possesses also capacity of global optimization of the immune algorithm. To verify our theoretical analysis and simulation, a HVSS test-bed was developed. The experimental results demonstrate that the fuzzy-immune PID controller managed to start the belt conveyor softly and to follow an S-shaped curve while the output speed correctly followed the preset speed with only small fluctuations in speed.展开更多
The dynamic characteristics of a belt conveyor are determined to a large extent by the properties of the belt. This paper describes experiments designed to establish the dynamic properties of belting material. The dyn...The dynamic characteristics of a belt conveyor are determined to a large extent by the properties of the belt. This paper describes experiments designed to establish the dynamic properties of belting material. The dynamic elastic modulus, viscous damping and rheologicat constants of the belt were measured. Several properties were studied as a function of the tensile loading on the belt. These included longitudinal vibration, the natural vibration frequency in the transverse direction and the response to an impulse excitation. Vibration response was observed under several different excitation frequencies. Most of these properties have not been tested previously under conditions appropriate for the ISO/DP9856 standard. Two types of belt were tested, a steel reinforced belt and a fabric reinforced belt. The test equipment was built to provide data appropriate for designing belt conveyors. It was observed that the stress wave propagation speed increased with tensile load and that tensile load was the main factor influencing longitudinal vibrations.展开更多
In this paper, we present a new voltage-mode biquad filter that uses a six-terminal CMOS fully differential current conveyor(FDCCII). The FDCCII with only 23 transistors in its structure and operating at ± 1.5 V,...In this paper, we present a new voltage-mode biquad filter that uses a six-terminal CMOS fully differential current conveyor(FDCCII). The FDCCII with only 23 transistors in its structure and operating at ± 1.5 V, is based on a class AB fully differential buffer. The proposed filter has the facility to tune gain, ωo and Q. A circuit division circuit(CDC) is employed to digitally control the FDCCII block. This digitally controlled FDCCII is used to realize a new reconfigurable fully-differential integrator and differentiator. We performed SPICE simulations to determine the performance of all circuits using CMOS 0.25 μm technology.展开更多
The mechanism of a hydro-viscous soft start is of great importance in the design of a hydro-viscous clutch and its control system. To explain the mechanism of a hydro-viscous soft start, the startup process of a belt ...The mechanism of a hydro-viscous soft start is of great importance in the design of a hydro-viscous clutch and its control system. To explain the mechanism of a hydro-viscous soft start, the startup process of a belt conveyor was numerically analyzed with the modified Reynolds equation, an energy equation and a temperature-viscosity equation. The effect of temperature and grooves of the friction disk surface on torque transfer and load capacity of the oil film have also been analyzed. The results show that 1) the grooves are the basis of forming dynamic pressure but they may reduce the capacity of torque transfer to a certain extent, 2) during the startup process, temperature has little effect on torque transfer and load capacity and the variation in load capacity of the oil film is very small, indicating that it is preferable to use the flow rate as a control object than the pressure of the feed cylinder. The results have been verified by an experiment.展开更多
The movement of the floating connecting mechanism between a hydraulic support and scraper conveyor is space movement;thus,when the hydraulic support pushes the scraper conveyor,there is an error between the actual dis...The movement of the floating connecting mechanism between a hydraulic support and scraper conveyor is space movement;thus,when the hydraulic support pushes the scraper conveyor,there is an error between the actual distance of the scraper conveyor and the theoretical moving distance.As a result,the scraper conveyor cannot obtain the straightness requirement.Therefore,the movement law of the floating connecting mechanism between the hydraulic support and scraper conveyor is analyzed and programmed into the Unity3D to realize accurate pushing of the scraper conveyor via hydraulic support.The Coal Seam?Equipment Joint Virtual Straightening System is established,and a straightening method based on the motion law of a floating connection is proposed as the default method of the system.In addition,a straightening simulation of the scraper conveyor was performed on a complex coal seam floor,the results demonstrate that the average straightening error of the scraper conveyor is within 2-8 mm,and is in direct proportion to the fluctuation of the coal seam floor in the strike of the seam with high accuracy,the straightness of scraper conveyor is more affected by the subsidence terrain during straightening than by the bulge terrain.And some conclusions are verified by experiment.Based on the verification of the relevant conclusions,a comparison and analysis of Longwall Automation Steering Committee(LASC)straightening technology and default straightening method in the simulation system shows that the straightness accuracy of LASC straightening technology under complex floor conditions is slightly less than that of the default straightening method in the proposed system.展开更多
文摘A new universal multiple input multiple output (MIMO) type current-mode biquad employing two dual output current conveyors (DOCCII), one multiple output current controlled current amplifier (MOCCCA) and four passive grounded elements is proposed which can realize all the five basic filtering functions namely, low-pass (LP), high-pass (HP), band-pass (BP), band-stop (BR) and all-pass (AP) in current mode from the same configuration. The centre frequency can be set by the passive elements of the circuit and the quality factor Q0 is electronically tunable through bias currents of the MOCCCA. Therefore, the biquad filter has independent tenability for the and Q0. The active and passive sensitivities of Q0 and are low. The workability of the new configuration has been demonstrated by PSPICE simulation results based upon a CMOS CCII in0.35μm technology.
基金jointly supported by the China National Science Foundation under Grant Nos.41875172 and 42075192。
文摘This paper studied a snow event over North China on 21 February 2017,using aircraft in-situ data,a Lagrangian analysis tool,and WRF simulations with different microphysical schemes to investigate the supercooled layer of warm conveyor belts(WCBs).Based on the aircraft data,we found a fine vertical structure within clouds in the WCB and highlighted a 1-2 km thin supercooled liquid water layer with a maximum Liquid Water Content(LWC) exceeding0.5 g kg^(-1) during the vertical aircraft observation.Although the main features of thermodynamic profiles were essentially captured by both modeling schemes,the microphysical quantities exhibited large diversity with different microphysics schemes.The conventional Morrison two-moment scheme showed remarkable agreement with in-situ observations,both in terms of the thermodynamic structure and the supercooled liquid water layer.However,the microphysical structure of the WCB clouds,in terms of LWC and IWC,was not apparent in HUJI fast bin scheme.To reduce such uncertainty,future work may focus on improving the representation of microphysics in bin schemes with in-situ data and using similar assumptions for all schemes to isolate the impact of physics.
文摘The State Council, or China＇s cabinet, has called for a middle to long-term plan to pro- mote new-style urbanization, enabling more migrant workers and their families to settle in cities.
文摘The oil film clutch, which is superior in speed adjustment, is capable of being used in the belt conveyor to carry out soft start operation. According to running properties of both belt conveyor and oil film clutch, equations that are used to decide the lubricating oil flow and the number of oil films (i.e. the number of rotating and stationary plates) are deduced theoretically. Also key parameters are provided for the design of the hydraulic system. All these together provide the theoretical basis for the soft start design of the belt conveyor and references for the application of the oil film clutch in similar fields.
文摘The key technology of semi-continuous conveyor system decides the successful using of this system. The key technology includes optimal initial building depth of this system,the crusher moving step and the layout of conveyor system are studied, and their calculating models are built up.
文摘Considering the control difficulties of a hydro-viscous trol algorithm was derived. A fuzzy-immune PID controller was soft start （HVSS） device of a belt conveyor, a fuzzy-immune con- designed based on immune feedback regulations and adaptability of the fuzzy logic inference. Using MATLAB software, we simulated the controller and compared the HVSS device with a conven- tional PID controller and a fuzzy PID controller. The simulation results show that the controller is not only very reliable as a PID controller, robust and requires only a short adjustment time of fuzzy control, but possesses also capacity of global optimization of the immune algorithm. To verify our theoretical analysis and simulation, a HVSS test-bed was developed. The experimental results demonstrate that the fuzzy-immune PID controller managed to start the belt conveyor softly and to follow an S-shaped curve while the output speed correctly followed the preset speed with only small fluctuations in speed.
文摘The dynamic characteristics of a belt conveyor are determined to a large extent by the properties of the belt. This paper describes experiments designed to establish the dynamic properties of belting material. The dynamic elastic modulus, viscous damping and rheologicat constants of the belt were measured. Several properties were studied as a function of the tensile loading on the belt. These included longitudinal vibration, the natural vibration frequency in the transverse direction and the response to an impulse excitation. Vibration response was observed under several different excitation frequencies. Most of these properties have not been tested previously under conditions appropriate for the ISO/DP9856 standard. Two types of belt were tested, a steel reinforced belt and a fabric reinforced belt. The test equipment was built to provide data appropriate for designing belt conveyors. It was observed that the stress wave propagation speed increased with tensile load and that tensile load was the main factor influencing longitudinal vibrations.
基金UGC for providing valuable support in form of the NET-JRF grant
文摘In this paper, we present a new voltage-mode biquad filter that uses a six-terminal CMOS fully differential current conveyor(FDCCII). The FDCCII with only 23 transistors in its structure and operating at ± 1.5 V, is based on a class AB fully differential buffer. The proposed filter has the facility to tune gain, ωo and Q. A circuit division circuit(CDC) is employed to digitally control the FDCCII block. This digitally controlled FDCCII is used to realize a new reconfigurable fully-differential integrator and differentiator. We performed SPICE simulations to determine the performance of all circuits using CMOS 0.25 μm technology.
文摘The mechanism of a hydro-viscous soft start is of great importance in the design of a hydro-viscous clutch and its control system. To explain the mechanism of a hydro-viscous soft start, the startup process of a belt conveyor was numerically analyzed with the modified Reynolds equation, an energy equation and a temperature-viscosity equation. The effect of temperature and grooves of the friction disk surface on torque transfer and load capacity of the oil film have also been analyzed. The results show that 1) the grooves are the basis of forming dynamic pressure but they may reduce the capacity of torque transfer to a certain extent, 2) during the startup process, temperature has little effect on torque transfer and load capacity and the variation in load capacity of the oil film is very small, indicating that it is preferable to use the flow rate as a control object than the pressure of the feed cylinder. The results have been verified by an experiment.
基金This research was supported by the Project funded by National Natural Science Foundation of China(Grant No.52004174)China Postdoctoral Science Foundation(No.2019M651081)+2 种基金the Key Research and Development Program of Shanxi(201903D121141)the Natural Science Foundation of Shanxi Province(201901D211022)the Scientific and Technological Innovation Programs of Higher Education Institutions in Shan Xi(No.2019L0305).
文摘The movement of the floating connecting mechanism between a hydraulic support and scraper conveyor is space movement;thus,when the hydraulic support pushes the scraper conveyor,there is an error between the actual distance of the scraper conveyor and the theoretical moving distance.As a result,the scraper conveyor cannot obtain the straightness requirement.Therefore,the movement law of the floating connecting mechanism between the hydraulic support and scraper conveyor is analyzed and programmed into the Unity3D to realize accurate pushing of the scraper conveyor via hydraulic support.The Coal Seam?Equipment Joint Virtual Straightening System is established,and a straightening method based on the motion law of a floating connection is proposed as the default method of the system.In addition,a straightening simulation of the scraper conveyor was performed on a complex coal seam floor,the results demonstrate that the average straightening error of the scraper conveyor is within 2-8 mm,and is in direct proportion to the fluctuation of the coal seam floor in the strike of the seam with high accuracy,the straightness of scraper conveyor is more affected by the subsidence terrain during straightening than by the bulge terrain.And some conclusions are verified by experiment.Based on the verification of the relevant conclusions,a comparison and analysis of Longwall Automation Steering Committee(LASC)straightening technology and default straightening method in the simulation system shows that the straightness accuracy of LASC straightening technology under complex floor conditions is slightly less than that of the default straightening method in the proposed system.
