Effect of Shot Peening on Surface Damage Evolution Behavior of Cu-19Ni Alloy

Shot peening is a surface modification technology with the metal surface nano machine(SNC),which can modify the surface microstructure and extend the fatigue life of Cu-19Ni alloy.The hardness,damage evolution and mechanical properties were investigated and characterized by scanning electron microscope(SEM),laser confocal microscope(LSM)and material surface performance tester(CFT).The results showed that the surface roughness and friction coefficient of Cu-19Ni alloy decreased with the increase of shot peening duration and diameter,while the microhardness and strength increased.Moreover,with the increase in shot peening duration and diameter,SEM observation showed that the fracture dimples became smaller,meanwhile,with the increase of small cleavage planes,shear tearing ridges and the thickness of the surface nano layer,the fracture mode gradually evolved from plastic to brittle fracture.The uniaxial tensile test of shot peened Cu-19Ni alloy was carried out by MTS testing machine combined with digital image correlation technology(DIC).The evolution of Cu-19Ni surface damage was analyzed,and the evolution equations describing the damage of large deformation zone and small deformation zone were established.The effect of shot peening on the damage evolution behavior of Cu-19Ni alloy was revealed.

Effect of rare earths on corrosion resistance of Cu-30Ni alloys in simulated seawater

Cu-30Ni-xRE(x=0–0.213 wt.%) alloy was prepared by adding rare earths(RE) in melted Cu-30Ni alloy using metal mould casting method.The effects of RE on corrosion resistance of the alloy in simulated seawater were investigated using optical microscope,scanning electronic microscope with energy-dispersive spectrometer and electrochemical measurement system.The results showed that the corrosion resistance of Cu-30Ni alloy was greatly improved by adding proper amount of RE,whereas excess addition of RE worsened ...

Properties of oxide films grown on 25Cr20Ni alloy in air-H_2O and H_2-H_2O atmospheres

The oxidation kinetics,surface morphology and phase structure of oxide films grown on 25Cr20Ni alloy in air-H2O and H2-H2O atmospheres at 900 ℃ for 20 h were investigated.The anti-coking performance and resistance to carburization of the two oxide films were compared using 25Cr20Ni alloy tubes with an inner diameter of 10 mm and a length of 850 mm in a bench scale naphtha steam pyrolysis unit.The oxidation kinetics followed a parabolic law in an air-H2O atmosphere and a logarithm law in a H2-H2O atmosphere in the steady-state stage.The oxide film grown in the air-H2O atmosphere had cracks where the elements Fe and Ni were enriched and the un-cracked area was covered with octahedral-shaped MnCr2O4 spinels and Cr1.3Fe0.7O3 oxide clusters,while the oxide film grown in the H2-H2O atmosphere was intact and completely covered with dense standing blade MnCr2O4 spinels.In the pyrolysis tests,the anti-coking performance and resistance to carburization of the oxide film grown in the H2-H2O atmosphere were far better than that in the air-H2O atmosphere.The mass of coke formed in the oxide film grown in the H2-H2O atmosphere was less than 10％ of that in the air-H2O atmosphere.The Cr1.3Fe0.7O3 oxide clusters converted into Cr23C6 carbides and the cracks were filled with carbon in the oxide film grown in the air-H2O atmosphere after repeated coking and decoking tests,while the dense standing blade MnCr2O4 spinels remained unchanged in the oxide film grown in the H2-H2O atmosphere.The ethylene,propylene and butadiene yields in the pyrolysis tests were almost the same for the two oxide films.

Pre-bainitic Transformation in Fe-Ni Alloy

The behaviour of the pre bainitic transformation in Fe Ni alloy was investigated by using SAM, X ray diffraction and TEM. The results show that there is segregation of Ni atoms in austenite and that bainite forms in depleted regions of Ni atoms.

Influence of microstructure and surface condition on antifouling property of 90Cu-10Ni alloy in seawater

Through the experiment of natural seawater exposure corrosion, the antifouling properties of the plate specimens of 90Cu 10Ni alloy were studied, which were processed by different deformations, annealing treatments and surface treatments. The results indicate that after exposure corrosion for half a year, the antifouling properties of the specimens are quite different. The specimens processed by suitable deformations, annealing treatment at 650?℃ and pretreatment of surface film possess both good corrosion resistance and antifouling properties. However, the specimens processed by different deformations and annealing treatment at 450?℃ possess lower corrosion resistance, although they are also treated by the pretreatment of surface film; their antifouling properties change with different deformations. The relationships among the corrosion morphology and microstructure with the antifouling property of 90Cu 10Ni alloy are observed under the scanning electron microscopy (SEM).

Magnetization-Enhanced Dislocation Motion and Decreased Yield Strength of 60Fe40Ni Alloy

Using a special constant deflection device, the changes in dislocation configuration ahead of a loaded crack tip for 60Fe40Ni alloy. before and after magnetization in a magnetic field, have been studied in TEM. The results showed that the magnetization for 60Fe40Ni alloy could enhance dislocation emission, multiplication and motion. Also, the mechanical properties of 60Fe40Ni alloy, in air and in the magnetic field respectively have been investigated using the slow strain rate tension. And the results indicated that magnetization could make the yield strength corresponding to decrease by 26 percent, but did not influence the ultimate tensile strength and the fracture strain, which showed that magnetization could enhance plastic deformation.

Hydriding-dehydriding properties of Mg_2Ni alloy modified by ball-milling in tetrahydrofuran

A new approach of ball-milled Mg_2Ni in tetrahydrofuran (THF) to improve thehydriding kinetics of Mg_2Ni alloy is suggested and studied. It is found that the modified alloydisplayed the improved activity for hydriding even at relatively low temperature (e.g., 323-373 K).In the case of the sample milled in THF for 20 h, the hydrogen content (mass fraction) reaches 1.6 %at 323 K, 2.1% at 348 K and 3.4% at 448 K, respectively. The use of THF during grinding led to thechange of the structure, which is reflected by the broadening and weakening of the diffraction peaksin the XRD spectra. The XPS analysis shows that Mg (2s) binding energy peak of Mg_2Ni aftermodification shifted from a lower binding energy to a higher one, indicating the charge transferencebetween Mg and THF and the formation of catalytically active electron donor-acceptor (EDA)complexes on the surface of modified Mg_2Ni alloy.

Electrochemical Isolation and Determination of GCP Phase in a Fe-Cr-Ni Alloy

Geometrical Close Packed (GCP) phase in Fe Cr Ni alloy was quantitatively isolated and precisely determined when electrolyzed in 10 % H 3PO 4 electrolyte at a low current density of 5 mA/cm 2 and 22 ℃±1 ℃. The transpassive dissolution potential of the alloy matrix under above conditions is about 1 140 mV (SCE), at which GCP phase is in passive state and can be isolated from the alloy.[WT5”HZ〗

EFFECT OF INTERGRANULAR CARBIDES ON CREEP RUPTURE PROPERTIES OF Fe-15Cr-25Ni ALLOY

The intergranular carbides may significantly increase rupture life and ductility of the Fe-15Cr-25Ni alloy.This seems due to the grain boundary sliding and diffusion hindered by precipitation of intergranular carbides,so the nucleation and growth rate of cracks or cavities are reduced.

Cavitation Erosion Behavior of as-Welded Cu12Mn8Al3Fe2Ni Alloy

Cavitation erosion behavior of as-welded Cu12Mn8Al3Fe2Ni alloy in 3.5% NaCl aqueous solution was studied bymagnetostrictive vibratory device for cavitation erosion. The results show that the cavitation erosion resistance ofthe as-welded Cu12Mn8Al3Fe2Ni alloy is much more superior to that of the as-cast one. The cumulative mass lossand the mass loss rate of the as-welded Cu12Mn8Al3Fe2Ni alloy are almost 1/4 that of the as-cast one. SEM analysisof eroded specimens reveals that the as-cast Cu12Mn8Al3Fe2Ni alloy is attacked more severely than the as-weldedone. Microcracks causing cavitation damage initiate at the phase boundaries.

Electrochemical Hydrogen Absorbing/Desorbing Behavior of Double Phase Mg-Ni Alloy

The electrochemical performance of double phase Mg Ni alloy was characterized at 25°C and 70°C, in order to evaluate briefly its utility as negative electrode materials in nickel metal hydride batteries. The results show that the electrochemical capacity of double phase Mg Ni alloy is rarely low at 25°C, but increased rapidly when the temperature is enhanced, and the double phase Mg Ni alloy has its maximum capacity at the first discharge cycle, but the capacity degrades rapidly with cycling number.

First-principles calculations of Ni–(Co)–Mn–Cu–Ti all-d-metal Heusler alloy on martensitic transformation,mechanical and magnetic properties

The martensitic transformation,mechanical,and magnetic properties of the Ni_(2)Mn_(1.5-x)Cu_(x)Ti_(0.5) (x=0.125,0.25,0.375,0.5) and Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5)[(x=0.125,y=0.125,0.25,0.375,0.5) and (x=0.125,0.25,0.375,y=0.625)]alloys were systematically studied by the first-principles calculations.For the formation energy,the martensite is smaller than the austenite,the Ni–(Co)–Mn–Cu–Ti alloys studied in this work can undergo martensitic transformation.The austenite and non-modulated (NM) martensite always present antiferromagnetic state in the Ni_(2)Mn_(1.5-x)Cu_(x)Ti_(0.5) and Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5) (y<0.625) alloys.When y=0.625 in the Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5) series,the austenite presents ferromagnetic state while the NM martensite shows antiferromagnetic state.Cu doping can decrease the thermal hysteresis and anisotropy of the Ni–(Co)–Mn–Ti alloy.Increasing Mn and decreasing Ti content can improve the shear resistance and normal stress resistance,but reduce the toughness in the Ni–Mn–Cu–Ti alloy.And the ductility of the Co–Cu co-doping alloy is inferior to that of the Ni–Mn–Cu–Ti and Ni–Co–Mn–Ti alloys.The electronic density of states was studied to reveal the essence of the mechanical and magnetic properties.

Electrodeposition of Er-Ni Alloy Film in Dimethylsulfoxide

The cyclic voltammetry and chronoamperometry were used to investigate the electrochemical behaviors of Er(Ⅲ) and Ni(Ⅱ) in LiClO 4 DMSO(dimethylsufoxide) system on Pt and Cu electrodes. Experimental results indicated that the reduction of Er(Ⅲ) to Er and Ni(Ⅱ) to Ni were irreversible in one step on Pt and Cu electrodes. The diffusion coefficient and electron transfer coefficient of Er(Ⅲ) in 0.01 mol·L -1 ErCl 3 -0.1 mol·L -1 LiClO 4 DMSO system at 303K were 1.47×10 -10 m 2·s -1 and 0.108 respectively, and the diffusion coefficient and electron transfer coefficient of Ni(Ⅱ) in 0.01 mol·L -1 NiCl 2-0.1 mol·L -1 LiClO 4 DMSO system at 303K were 3.38×10 -10 m 2·s -1 and 0.160 respectively. The homogeneous, strong adhesive Er Ni alloy films with metallic lu- stre was prepared by potentiostatic electrolysis on Cu electrode in ErCl 3 NiCl 2 LiClO 4 DMSO system at -1.90～ -2.55 V (vs SCE).

Effects of Ni addition on liquid phase separation and giant magnetoresistance of Cu-Co alloys

The effects of Ni addition on the liquid phase separation and giant magnetoresi stance (GMR) of Cu Co alloys were discussed. The results reveal that Ni additio n can partially restrain the liquid phase separation of Cu Co alloys, resultin g in a decrease of volume fraction for the Co rich particles separated from the liquid phase and in refined microstructures. The composition analyses indicate t hat Ni is dissolved in both the Co rich and the Cu rich phases, but Ni content in the Co rich phase is much higher than that in the Cu matrix. At the same ti me, Ni addition enhance the solubility between Cu and Co, especially Cu in Co s olid solution. Ni alloying into Cu Co alloys can fully prevent the liquid phase separation during melt spinning, which is very beneficial to improve GMR of Cu Co alloys.

Effect of cerium addition on oxidation behavior of 25Cr20Ni alloy under low oxygen partial pressure

The influence of Ce addition on the oxidation behavior of 25Cr20Ni alloy at 950 oC under low oxygen partial pressure was inves-tigated. The oxidized samples were characterized by using X-ray diffraction （XRD）, scanning electron microscopy （SEM）, energy dispersive X-ray spectroscopy （EDS）, and scratch tester to obtain the oxide phases, morphology, thickness, composition and adhesion property of the oxide scales. The experiment results indicated that a small amount of Ce addition （0.02 wt.% or 0.05 wt.%） promoted oxidation resistance and inhibited the growth of the needlelike oxide. The Ce addition also decreased the formation of MnCr2O4 but promoted the SiO2 formation un-derneath the Cr2O3, which largely contributed to the improvement of oxide scale spallation resistance. For the sample with 0.3 wt.% Ce addi-tion, the oxidation rate significantly increased and the spallation resistance of the oxide scale decreased.

Stabilization of Cu/Ni Alloy Nanoparticles with Graphdiyne Enabling Efficient CO_(2) Reduction

Electrocatalysis has become an attractive strategy for the artificial reduction of CO_(2) to high-value chemicals.However,the design and development of highly selective and stable non-noble metal electrocatalysts that convert CO_(2) to CO are still a challenge.As a new type of two-dimensional carbon material,graphdiyne(GDY),is rarely used to explore the application in carbon dioxide reduction reaction(CO_(2)RR).Therefore,we tried to use GDY as a substrate to stabilize the copper-nickel alloy nanoparticles(NPs)to synthesize Cu/Ni@GDY.Cu/Ni@GDY requires an overpotential(−0.61 V)to 10 mA/cm^(2) for the formation of CO,and it shows better activity than Au and Ag,achieving a higher Faraday efficiency of about 95.2%and high stability of about 26 h at an overpotential(−0.70 V).The electronic interaction between GDY substrate and Cu/Ni alloy NPs and the large specific surface area of GDY is responsible for the high performance.

Correlation Between Microstructure and Corrosion Behavior of Two 90Cu10Ni Alloy Tubes

Two kinds of 90Cu10 Ni tubes with different service lives（more than 3 years and only 1 year,respectively）under identical working conditions were studied by an immersion test in a 3.5 wt% NaCl solution and the electron backscattered diffraction（EBSD） technique.The morphology after immersion showed severer corrosion attack at the grain boundaries of the tube with shorter service life compared with the tube with longer service life.The grain boundary characterization distributions（GBCDs） of the two tubes obtained by EBSD revealed more Σ3 boundaries and twins,and larger random boundary meshes in the tube with longer service life.A short immersion test in a modified Livingston＇s solution was conducted to evaluate the tendency to corrosion attack of different types of the grain boundaries.SEM and AFM were used to characterize the corrosion morphologies of the boundaries.A strong correlation between varying depths of corrosion grooves and types of the grain boundaries was obtained.The influence of deviation angle of low Σ boundaries on corrosion resistance of the grain boundaries was also discussed.It is concluded that a special ‘‘grain boundary engineering＇＇（GBE） treatment has been performed on the tube with longer service life.It is proposed that the optimized GBCD is responsible for the better service performance of the tube.

Corrosion Resistance of Deformed Cu-Ni Alloy in Seawater

After solutionized, 70Cu 30Ni alloy was deformed in different degrees and then exposed both in NaCl solution and in seawater. The results show that with the increase of deformation, the E c and R p -1 of 70Cu 30Ni alloy decrease more quickly and fluctuate less when the exposure time increases, and the corrosion product films contain more nickel and less chloride because the distribution of dislocations tends to be homogeneous.

Preparation of La-Ni Based Alloys Used in Ni-Metal Hydride Bateries by Mechanical Alloying

La Ni based alloy powders used for Ni metal hydride batteries were synthesized by mechanical alloying starting from the elements. The electrical capacity obtained was up to 320 mAh/g. In addition, the comparison in the microstructure and electrochemical properties was made between the alloy powders produced by mechanical alloying and by melting. It was shown that mechanical alloying is promising in the preparation of practical RE hydrogen storage electrode materials.

In situ Study on the Growth Behavior of Primary Al_3Ni Phase in Solidifying Al–Ni Alloy by Synchrotron Radiography

The growth behavior of Al_3Ni intermetallic compounds（IMCs）during the directional solidification of Al-10 wt%Ni alloy was investigated by synchrotron radiography.Two main growth patterns of primary Al_3Ni phase,I-like and V-like,appeared during solidification,and I-like Al_3Ni phase grew faster than V-like phase,which can be explained by the minimum energy criterion.The growth of I-like phase can be divided into two stages and was mainly affected by undercooling and Ni concentration.We also found that V-like Al_3Ni phase can evolve into M-like phase during solidification.