Identification of relevant active sites and a mechanism study for reverse water gas shift reaction over Pt/CeO_2 catalysts

Reverse water gas shift (RWGS) reaction can serve as a pivotal stage in the CO2 conversion processes, which is vital for the utilization of CO2. In this study, RWGS reaction was performed over Pt/CeO2 catalysts at the temperature range of 200-500 degrees C under ambient pressure. Compared with pure CeO2, Pt/CeO2 catalysts exhibited superior RWGS activity at lower reaction temperature. Meanwhile, the calculated TOF and E-a values are approximately the same over these Pt/CeO2 catalysts pretreated under various calcination conditions, indicating that the RWGS reaction is not affected by the morphologies of anchored Pt nanoparticles or the primary crystallinity of CeO2. TPR and XPS results indicated that the incorporation of Pt promoted the reducibility of CeO2 support and remarkably increased the content of Ce 3 + sites on the catalyst surface. Furthermore, the CO TPSR-MS signal under the condition of pure CO2 flow over Pt/CeO 2 catalyst is far lower than that under the condition of adsorbed CO2 with H-2 -assisted flow, revealing that CO2 molecules adsorbed on Ce3+ active sites have difficult in generating CO directly. Meanwhile, the adsorbed CO2 with the assistance of H-2 can form formate species easily over Ce3+ active sites and then decompose into Ce3+-CO species for CO production, which was identified by in-situ FTIR. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B. V. and Science Press. All rights reserved.

Screening of MgO- and CeO_2-Based Catalysts for Carbon Dioxide Oxidative Coupling of Methane to C_(2+) Hydrocarbons

The catalyst screening tests for carbon dioxide oxidative coupling of methane (CO2-OCM) have been investigated over ternary and binary metal oxide catalysts. The catalysts are prepared by doping MgO- and CeO2-based solids with oxides from alkali (Li2O), alkaline earth (CaO), and transition metal groups (WO3 or MnO). The presence of the peroxide (O2-2) active sites on the Li2O2, revealed by Raman spectroscopy, may be the key factor in the enhanced performance of some of the Li2O/MgO catalysts. The high reducibility of the CeO2 catalyst, an important factor in the CO2-OCM catalyst activity, may be enhanced by the presence of manganese oxide species. The manganese oxide species increases oxygen mobility and oxygen vacancies in the CeO2 catalyst. Raman and Fourier Transform Infra Red (FT-IR) spectroscopies revealed the presence of lattice vibrations of metal-oxygen bondings and active sites in which the peaks corresponding to the bulk crystalline structures of Li2O, CaO, WO3 and MnO are detected. The performance of 5%MnO/15%CaO/CeO2 catalyst is the most potential among the CeO2-based catalysts, although lower than the 2%Li2O/MgO catalyst. The 2%Li2O/MgO catalyst showed the most promising C2+ hydrocarbons selectivity and yield at 98.0% and 5.7%, respectively.

Electronic and geometric structure of the copper-ceria interface on Cu/CeO2 catalysts

The atomic structure of the active sites in Cu/CeO2 catalysts is intimately associated with the copper-ceria interaction. Both the shape of ceria and the loading of copper affect the chemical bonding of copper species on ceria surfaces and the electronic and geometric character of the relevant interfaces. Nanostructured ceria, including particles(polyhedra), rods, and cubes, provides anchoring sites for the copper species. The atomic arrangements and chemical properties of the(111),(110) and(100) facets, preferentially exposed depending on the shape of ceria, govern the copper-ceria interactions and in turn determine their catalytic properties. Also, the metal loading significantly influences the dispersion of copper species on ceria with a specific shape, forming copper layers, clusters, and nanoparticles. Lower copper contents result in copper monolayers and/or bilayers while higher copper loadings lead to multi-layered clusters and faceted particles. The active sites are usually generated via interactions between the copper atoms in the metal species and the oxygen vacancies on ceria, which is closely linked to the number and density of surface oxygen vacancies dominated by the shape of ceria.

Methane reforming with CO_2 to syngas over CeO_2-promoted Ni/Al_2O_3-ZrO_2 catalysts prepared via a direct sol-gel process

CeO2-promoted Ni/Al2O3-ZrO2 （Ni/Al2O3-ZrO2-CeO2） catalysts were prepared by a direct sol-gel process with citric acid as gelling agent. The catalysts used for the methane reforming with CO2 was studied by infrared spectroscopy （IR）, thermal gravimetric analysis （TGA）, microscopic analysis, X-ray diffraction （XRD） and temperature-programmed reduction （TPR）. The catalytic performance for CO2 reforming of methane to synthesis gas was investigated in a continuous-flow micro-reactor under atmospheric pressure. TGA, IR, XRD and microscopic analysis show that the catalysts prepared by the direct sol-gel process consist of Ni particles with a nanostructure of around 5 nm and an amorphous-phase composite oxide support. There exists a chemical interaction between metallic Ni particles and supports, which makes metallic Ni well dispersed, highly active and stable. The addition of CeO2 effectively improves the dispersion and the stability of Ni particles of the prepared catalysts, and enhances the adsorption of CO2 on the surface of catalysts. The catalytic tests for methane reforming with CO2 to synthesis gas show that the Ni/Al2O3-ZrO2-CeO2 catalysts show excellent activity and stability compared with the Ni/Al2O3 catalyst. The excellent catalytic activity and stability of the Ni/Al2O3-ZrO2-CeO2 are attributed to the highly, uniformly and stably dispersed small metallic Ni particles, the high reducibility of the Ni oxides and the interaction between metallic Ni particles and the composite oxide supports.

Partial Oxidation of Methane over Monolithic Ni/CeO_2-ZrO_2/γ-Al_2O_3 Catalysts

A series of monolithic Ni/CeO_2-ZrO_2/γ-Al_2O_3 catalysts for the POM reaction were prepared. The activity test shows that the catalyst has the best performance when CeO_2-ZrO_2 content is 8 wt%.The synergistic actions between CeO_2-ZrO_2 and γ-Al_2O_3 improve highly catalytic activity by increasing CH_4 conversion, H_2 and CO selectivity. XPS analysis of the used catalyst indicates that there coexist Ce^(4+) and Ce^(3+).

Ni/CeO_(2)基催化剂构筑及其CO_(2)甲烷化催化性能研究进展

CO_(2)加氢制甲烷(即“CO_(2)甲烷化”)是实现碳中和目标的重要途径。CeO_(2)由于具有丰富的表面氧空位和优异的储氧性能被认为是重要的催化剂载体之一,过渡金属Ni也因为具有优异的催化性能和低廉的价格被广泛应用于催化剂的研究,CeO_(2)和金属Ni结合形成的Ni/CeO_(2)基催化剂在CO_(2)甲烷化反应中展现了良好的应用前景。阐述了Ni/CeO_(2)基催化剂催化CO_(2)甲烷化的机理,介绍了Ni/CeO_(2)基催化剂制备方法,重点总结了活性中心特征、载体性质、助剂类型和金属-载体相互作用等影响Ni/CeO_(2)基催化CO_(2)甲烷化催化性能的因素,并总结了改性Ni/CeO_(2)基催化剂的催化性能。分析发现,通过对Ni/CeO_(2)基催化剂进行改性,可以调控Ni/CeO_(2)基催化剂的CO_(2)甲烷化催化性能与产物选择性,可为提升其CO_(2)甲烷化催化性能提供新的思路。

Ni/CeO_(2)催化剂上CO_(2)甲烷化反应本征动力学研究

CO_(2)加氢合成CH4(CO_(2)甲烷化)是CO_(2)高效、清洁转化的重要途径之一。尽管CO_(2)甲烷化的催化体系研究已较深入,但特定条件下CO_(2)甲烷化本征动力学的研究较少。采用燃烧法制备了Ni/CeO_(2)催化剂(Ni质量分数为10%),并通过加入内稀释剂(α-Al_(2)O_(3))制备了不同m(α-Al_(2)O_(3)):m(Ni/CeO_(2))的样品。考察了在温度为300℃、压力为1 MPa和空速为3×10^(6)mL/(g·h)的条件下,m(α-Al_(2)O_(3)):m(Ni/CeO_(2))=25:1样品(样品A)的CO_(2)甲烷化本征动力学。结合本征动力学测试、漫反射红外光谱、H_(2)-程序升温还原和H_(2)-程序升温脱附等对CO_(2)甲烷化本征反应动力学方程进行了深入分析。结果表明,样品A作用下的CH_(4)生成速率最高可达41.4mmol/(g·h)(H_(2)分压为400kPa,CO_(2)分压为120 kPa)。当CO_(2)分压为30~120 kPa时,CH_(4)生成速率随H_(2)分压的增大线性增长,并且不受CO_(2)分压或CO分压变化的影响。在该CO_(2)分压范围内,富氢环境可以显著提高催化剂的CO_(2)甲烷化催化活性。

Methanation of syngas over coral reef-like Ni/Al_2O_3 catalysts

Coral reef-like Ni/Al2O3 catalysts were prepared by co-precipitation of nickel acetate and aluminium nitrate with sodium carbonate aqueous solution in the medium of ethylene glycolye.Methanation of syngas was carried out over coral reef-like Ni/Al2O3 catalysts in a continuous flow type fixed-bed reactor.The structure and properties of the fresh and used catalysts were studied by SEM,N2 adsorption-desorption,XRD,H2-TPR,O2-TPO,TG and ICP-AES techniques.The results showed that the coral reef-like Ni/Al2O3 catalysts exhibited better activity than the conventional Ni/Al2O3-H2O catalysts.The activities of coral reef-like catalysts were in the order of Ni/Al2O3-673Ni/Al2O3-573Ni/Al2O3- 473Ni/Al2O3-773.Ni/Al2O3-673-EG catalyst showed not only good activity and improved stability but also superior resistance to carbon deposition,sintering,and Ni loss.Under the reaction conditions of CO/H2（molar ratio）=1：3,593 K,atmospheric pressure and a GHSV of 2500 h-1,CH4 selectivity was 84.7%,and the CO conversion reached 98.2%.

The Effect of Titania Structure on Ni/TiO_2 Catalysts for p-Nitrophenol Hydrogenation

The catalytic hydrogenation of p-nitrophenol to p-aminophenol was investigated over Ni/TiO2 catalysts prepared by a liquid-phase chemical reduction method. The catalysts were characterized by inductively coupled plasma (ICP), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectra (XPS) and temperature-programmed reduction (TPR). Results show that the titania structure has favorable influence on physio-chemical and catalytic properties of Ni/TiO2 catalysts. Compared to commercial Raney nickel, the catalytic activity of Ni/TiO2 catalyst is much superior, irrespective of the titania structure. The catalytic activity of anatase titania supported nickel catalyst Ni/TiO2(A) is higher than that of rutile titania supported nickel catalyst Ni/TiO2(R), possibly because the reduction of nickel oxide to metallic nickel for Ni/TiO2(A) is easier than that for Ni/TiO2(R) at similar reaction conditions.

Influence of preparation methods on the physicochemical properties and catalytic performance of MnO_x-CeO_2 catalysts for NH_3-SCR at low temperature

This work examines the influence of preparation methods on the physicochemical properties and catalytic performance of MnOx‐CeO2 catalysts for selective catalytic reduction of NO by NH3 (NH3‐SCR) at low temperature. Five different methods, namely, mechanical mixing, impregnation,hydrothermal treatment, co‐precipitation, and a sol‐gel technique, were used to synthesizeMnOx‐CeO2 catalysts. The catalysts were characterized in detail, and an NH3‐SCR model reaction waschosen to evaluate the catalytic performance. The results showed that the preparation methodsaffected the catalytic performance in the order: hydrothermal treatment > sol‐gel > co‐precipitation> impregnation > mechanical mixing. This order correlated with the surface Ce3+ and Mn4+ content,oxygen vacancies and surface adsorbed oxygen species concentration, and the amount of acidic sitesand acidic strength. This trend is related to redox interactions between MnOx and CeO2. The catalystformed by a hydrothermal treatment exhibited excellent physicochemical properties, optimal catalyticperformance, and good H2O resistance in NH3‐SCR reaction. This was attributed to incorporationof Mnn+ into the CeO2 lattice to form a uniform ceria‐based solid solution (containing Mn‐O‐Cestructures). Strengthening of the electronic interactions between MnOx and CeO2, driven by thehigh‐temperature and high‐pressure conditions during the hydrothermal treatment also improved the catalyst characteristics. Thus, the hydrothermal treatment method is an efficient and environment‐friendly route to synthesizing low‐temperature denitrification (deNOx) catalysts.

Preparation, Characterization of CuO/CeO_2 and Cu/CeO_2 Catalysts and Their Applications in Low-Temperature CO Oxidation

CeO2 was synthesized via sol-gel process and used as supporter to prepare CuO/CeO2, Cu/CeO2 catalysts by impregnation method. The catalytic properties and characterization of CeO2, CuO/CeO2 and Cu/CeO2 catalysts were examined by means of a microreactor-GC system, HRTEM, XRD, TPR and XPS techniques. The results show that CuO has not catalytic activity and the activity of CeO2 is quite low for CO oxidation. However, the catalytic activity of CuO/CeO2 and Cu/ CeO2 catalysts increases significantly. Furthermore, the activity of CuO/CeO2 is higher than that of Cu/CeO2 catalysts.

Mechanistic insight into N_2O formation during NO reduction by NH_3 over Pd/CeO_2 catalyst in the absence of O_2

N2O is a major by-product emitted during low-temperature selective catalytic reduction of NO with NH3(NH3-SCR), which causes a series of serious environmental problems. A full understanding of the N2O formation mechanism is essential to suppress the N2O emission during the low-temperature NH3-SCR, and requires an intensive study of this heterogeneous catalysis process. In this study, we investigated the reaction between NH3 and NO over a Pd/CeO2 catalyst in the absence of O2, using X-ray photoelectron spectroscopy, NH3-temperature-programmed desorption, NO-temperature-programmed desorption, and in-situ Fourier-transform infrared spectroscopy. Our results indicate that the N2O formation mechanism is reaction-temperature-dependent. At temperatures below 250 ℃, the dissociation of HON, which is produced from the reaction between surface H· adatoms and adsorbed NO, is the key process for N2O formation. At temperatures above 250 ℃,the reaction between NO and surface N·, which is produced by NO dissociation, is the only route for N2O formation, and the dissociation of NO is the rate-determining step. Under optimal reaction conditions, a high performance with nearly 100% NO conversion and 100% N2 selectivity could be achieved. These results provide important information to clarify the mechanism of N2O formation and possible suppression of N2 O emission during low-temperature NH3-SCR.

Effect of Alumina Particle Size on Ni/Al2O3 Catalysts for p-Nitrophenol Hydrogenation

The catalytic hydrogenation of p-nitrophenol to p-aminophenol was investigated over Ni/Al2O3 catalyst on alumina support with different particle size. It is found that support particle size has significant influences on physiochemical properties and catalytic activity of the resulting Ni/Al2O3 catalyst, but little influence on the selec-tivity. At a comparable amount of Ni loading, the catalytic activity of Ni/Al2O3 prepared with alumina support of smaller particle size is lower. The reduction behavior of the catalyst is a key factor in determining the catalytic activity of Ni/Al2O3 catalyst. The supported nickel catalyst 10.3Ni/Al2O3-3 improves the life span of the membrane by reducing fouling on the membrane surface compared to nano-sized nickel.

Ni/bentonite catalysts prepared by solution combustion method for CO_2 methanation

A 20 wt% Ni/bentonite catalyst was prepared by a solution combustion synthesis (SCS), which exhibited higher activity for the CO_2methanation than that of an impregnation method (IPM), and the catalyst prepared by SCS showed a CO_2 conversion of 85% and a CH4selectivity of 100% at 300 °C, atmospheric pressure, and 3600 ml·(g cat)-1·h-1, and the catalyst exhibited stable within a 110-h reaction. The results showed higher me- tallic Ni dispersion, smaller Ni particle size, larger specific surface area and lower reduction temperature in the Ni/ bentonite prepared by SCS than that of IPM. And the Ni/bentonite prepared by the SCS moderated the interaction between NiO and bentonite.

Effects of Cerium Oxide on Ni/Al_2O_3 Catalysts for Decomposition of CH_4 and C_2H_4

Characteristics of carbon deposition of CH 4 and C 2H 4 decomposition over supported Ni and Ni Ce catalysts were studied by using a pulse reaction as well as BET, TPR, XPS and hydrogen chemisorption techniques. It is found that there is a metal semiconductor interaction (MScI) in the Ni Ce catalyst, and the effect of MScI on the carbon deposition of CH 4 decomposition is opposite to that of C 2H 4. A novel model of carbon deposition of CH 4 or C 2H 4 decomposition was proposed.

CeO_2-Co_3O_4 Catalysts for CO Oxidation

CeO2-Co3O4 catalysts for low-temperature CO oxidation were prepared by a co-precipitation method. In combination with the characterization methods of N2 adsorption/desorption, XRD, temperature-programmed reduction （TPR）, and FT-IR, the influence of the cerium content on the catalytic performance of CeO2-Co3O4 was investigated. The results indicate that the prepared CeO2-Co3O4 catalysts exhibit a better activity than that of pure CeO2 or pure Co3O4. The catalyst with the Ce/Co atomic ratio 1 ： 16 exhibits the best activity, which converts 77% of CO at room temperature and completely oxidizes CO at 45 ℃.

Partial oxidation of methane over SiO2 supported Ni and NiCe catalysts

Nickel and nickel-ceria catalysts supported on high surface area silica, with 6 wt% Ni and 20 wt% CeO2 were prepared by microwave assisted(co) precipitation method. The catalysts were investigated by XRD,TPR and XPS analyses and they were tested in partial oxidation of methane(CPO). The catalytic reaction was carried out at atmospheric pressure in a temperature range of 400–800℃ with a feed gas mixture containing methane and oxygen in a molecular ratio CH4/O2=2. The Ni catalyst exhibited 60% methane conversion with 60% selectivity to CO already at 500℃. On the contrary, the Ni–Ce catalyst was inert to CPO up to 700℃. Moreover, the former catalyst reproduced its activity at the descending temperatures maintaining a good stability at 600℃, over a reaction time of 80 h, whereas the latter one completely deactivated. Test of CH4 temperature programmed surface reaction(CH4-TPSR) revealed a higher methane activation temperature(> 100℃) for the Ni–Ce catalyst as compared to the Ni one. Noticeable improvement of the ceria containing catalyst occurred when the reaction test started at a temperature higher than the methane decomposition temperature. In this case, the sample achieved the same catalytic behavior of the Ni catalyst. As confirmed by XPS analyses, the distinct electronic state of the supported nickel was responsible for the differences in catalytic behavior.

Insight into MgO promoter with low concentration for the carbon-deposition resistance of Ni-based catalysts in the CO_2 reforming of CH_4

The CO2reforming of CH4is studied over MgO‐promoted Ni catalysts,which were supported on alumina prepared from hydrotalcite.This presents an improved stability compared with non‐promoted catalysts.The introduction of the MgO promoter was achieved through the‘‘memory effect’’of the Ni‐Al hydrotalcite structure,and ICP‐MS confirmed that only0.42wt.%of Mg2+ions were added into the Ni‐Mg/Al catalyst.Although no differences in the Ni particle size and basicity strength were observed,the Ni‐Mg/Al catalyst showed a higher catalytic stability than the Ni/Al catalyst.A series of surface reaction experiments were used and showed that the addition of a MgO promoter with low concentration can promote CO2dissociation to form active surface oxygen arising from the formation of the Ni‐MgO interface sites.Therefore,the carbon‐resistance promotion by nature was suggested to contribute to an oxidative environment around Ni particles,which would increase the conversion of carbon residues from CH4cracking to yield CO on the Ni metal surface.?2018,Dalian Institute of Chemical Physics,Chinese Academy of Sciences.Published by Elsevier B.V.All rights reserved.

Dry reforming of methane on active and coke resistant Ni/Y_2Zr_2O_7 catalysts treated by dielectric barrier discharge plasma

In this study, Ni/YZrOcatalysts prepared with impregnation method and treated by dielectric barrier discharge plasma(DBD) in different atmospheres have been investigated for methane dry reforming. It is revealed by H-TPR that plasma treatment can enhance the interaction between Ni O/Ni particles and the YZrOpyrochlore support. Therefore, catalysts with smaller Ni O and Ni grains sizes, higher metallic Ni active surface areas can be achieved, as evidenced by XRD, TEM and Hadsorption-desorption measurements. As a consequence, the plasma-treated catalysts show significantly improved activity, stability and coke resistance, as testified by the TEM and TGA-DSC results. Plasma treatment in H/Ar gas mixture is found to be the best condition to prepare Ni/YZrO, which can be used to obtain a catalyst with the highest activity, stability and most potent coke resistance. It is believed that the smaller Ni grain size and higher metallic Ni active surface area induced by plasma treatment are the inherent reasons accounting for the promoted reaction performance of the Ni/YZrOpyrochlore catalysts.

Preferential oxidation of CO in excess H_2 over the CeO_2/CuO catalyst: Effect of initial support

Three series of CeO2/CuO samples were prepared by impregnation method and characterized by XRD, N2 adsorption-desorption, temperatureprogrammed reduction （TPR）, XPS and TEM techniques. In comparison with the samples prepared with CuO as initial support, the samples with Cu（OH）2 as initial support have higher reducibilities and smaller relative TPR peak areas, and also larger specific surface areas at calcina- tion temperatures of 400 ℃--600 ℃. As a result, Cu（OH）2 is better than CuO as initial support for preferential oxidation of CO in excess H2 （CO-PROX）. The best catalytic performance was achieved on the sample calcined at 600 ℃ and with an atomic ratio of Ce/Cu at 40%. XPS analyses indicate that more interface linkages Ce-O-Cu could be formed when it was calcined at 600 ℃. And the atomic ratio of Ce/Cu at 40% led to a proper reducibility for the sample as illustrated by the TPR measurements.