Ni/Al_2O_3-ZnO催化剂在FCC重汽油加氢脱砷的应用研究

以馏程在100~224℃、砷含量350ng·g^(-1)的FCC重汽油为原料,以镍质量分数28~31%的负载型Ni/Al_2O_3-ZnO催化剂为活性中心,在100ml加氢装置上评价了催化剂的加氢脱砷性能。评价结果表明:在压力1.8MPa、温度120~160℃、氢油比40~80(v/v)、空速4.0~6.0h^(-1)条件下,FCC重汽油具有良好的深度脱砷性能并保持催化活性稳定性,稳定运转2000h后,加氢产品中砷含量仍小于10ng.g^(-1),脱砷的同时有少量的加氢脱硫和脱烯烃反应发生。

喹啉对在Co-Mo/Al_2O_3及Ni-Mo/Al_2O_3催化剂上二苯并噻吩加氢脱硫活性的影响

在工业催化剂FHUDS-5(Co-Mo/Al2O3)和FHUDS-6(Ni-Mo/Al2O3)上,模拟工业柴油加氢工艺,考察了喹啉对二苯并噻吩(DBT)加氢脱硫(HDS)活性的影响,还讨论了喹啉抑制DBT加氢脱硫反应的机理。结果表明,喹啉对DBT的HDS反应有强烈抑制作用,对加氢路径(HYD)的抑制作用大于对氢解路径(DDS)的抑制作用;反应温度高于300℃时,在同一温度下,喹啉对在Co-Mo/Al2O3及Ni-Mo/Al2O3催化剂上DBT加氢脱硫反应活性的影响不同;当氢分压大于4.8 MPa时,在同一氢分压下,喹啉对在Co-Mo/Al2O3及Ni-Mo/Al2O3催化剂上DBT加氢脱硫反应活性的影响不同。

Enhanced CO oxidation over potassium-promoted Pt/Al_2O_3 catalysts:Kinetic and infrared spectroscopic study

A series of K-promoted Pt/Al2O3 catalysts were tested for CO oxidation. It was found that the addition of K significantly enhanced the activity. A detailed kinetic study showed that the activation energies of the K-containing catalysts were lower than those of the K-free ones, particularly for catalysts with high Pt contents （51.6 k）/mol for 0.42K-2.0Pt/Al2O3 and 6：3.6 kJ/mol for 2.0Pt/Al2O3 ）. The CO reaction orders were higher for the K-containing catalysts （about -0.2） than for the K-free ones （about -0.5）, with the former having much lower equilibrium constants for CO adsorption than the latter. In situ Fourier-transform infrared spectroscopy showed that surface CO desorption from the 0.42K-2.0Pt/Al2O3 catalyst was easier than from 2.0Pt/Al2O3. The promoting effect of K was therefore caused by weakening of the interactions between CO and surface Pt atoms. This decreased coverage of the catalyst with CO and facilitated competitive O2 chemisorption on the Pt surface, and significantly lowered the reaction barrier between chemisorbed CO and O2 species.

Methanation of syngas over coral reef-like Ni/Al_2O_3 catalysts

Coral reef-like Ni/Al2O3 catalysts were prepared by co-precipitation of nickel acetate and aluminium nitrate with sodium carbonate aqueous solution in the medium of ethylene glycolye.Methanation of syngas was carried out over coral reef-like Ni/Al2O3 catalysts in a continuous flow type fixed-bed reactor.The structure and properties of the fresh and used catalysts were studied by SEM,N2 adsorption-desorption,XRD,H2-TPR,O2-TPO,TG and ICP-AES techniques.The results showed that the coral reef-like Ni/Al2O3 catalysts exhibited better activity than the conventional Ni/Al2O3-H2O catalysts.The activities of coral reef-like catalysts were in the order of Ni/Al2O3-673Ni/Al2O3-573Ni/Al2O3- 473Ni/Al2O3-773.Ni/Al2O3-673-EG catalyst showed not only good activity and improved stability but also superior resistance to carbon deposition,sintering,and Ni loss.Under the reaction conditions of CO/H2（molar ratio）=1：3,593 K,atmospheric pressure and a GHSV of 2500 h-1,CH4 selectivity was 84.7%,and the CO conversion reached 98.2%.

Selective catalytic hydrogenation of naphthalene to tetralin over a NiMo/Al2O3 catalyst

The selective catalytic hydrogenation of naphthalene to high-value tetralin was systematically investigated.A series of Al2O3 catalysts containing different active metals(Co,Mo,Ni,W)were prepared by incipient wetness impregnation.The effects of different active metals forms(oxidation,reduction,sulfuration)and reaction conditions on naphthalene hydrogenation were investigated and the catalysts were characterized by XRD,XPS,BET,NH3-TPD and SEM.Especially,Ni-Mo/Al2O3 was first used in this reactive system.The results show that the oxidative4%Ni O-20%MoO3/Al2O3 is the best catalyst for the preparation of tetralin.The conversion of naphthalene and the selectivity of tetralin can reach 95.62%and 99.75%respectively at 200℃,8 h and 6 MPa.Compared with reduced and sulfureted 4%Ni O-20%MoO3/Al2O3 catalysts,oxidative 4%Ni O-20%MoO3/Al2O3 has a well dispersed and uniform monolayer of the active metals,larger pore volume and size,and larger total acidity.NiO-MoO3/Al2O3 has a synergistic effect between NiO activity and MoO3 selectivity.

Investigation of the characteristics and deactivation of catalytic active center of Cr-Al_2O_3 catalysts for isobutane dehydrogenation

Deactivation mechanism of Cr-Al2O3catalyst and the interaction of Cr-A1 in the dehydrogenation of isobutane, as well as the nature of the catalytic active center, were studied using XRD, SEM, XPS, H2-TPR, isobutane-TPR and TPO techniques. The results revealed that the deactivation of Cr-Al2O3 catalyst was mainly caused by carbon deposition on its surface. The Cr3＋ ion could not be reduced by hydrogen but could be reduced to Cr2＋ by hydrocarbons and monoxide carbon. The active center for isobutane dehydrogenation could be Cr2＋/Cr3＋ produced from Cr6＋ by the on line reduction of hydrocarbon and carbon monoxide. The binding energy of Al3＋ was strongly affected by the state of chromium cations in the catalysts.

Ethanol steam reforming over Ni-Cu/Al_2O_3-M_yO_z (M = Si, La, Mg,and Zn) catalysts

Ni-based catalysts doped with copper additives were studied on their role in ethanol steam reforming reaction. The effects of Cu content, support species involving Al2O3-SIO2, Al2O3-MgO, Al2O3-ZnO, and Al2O3-La2O3, on the catalytic performance were studied. Characterizations by TPR, XRD, NH3-TPD, XPS, and TGA indicated that catalysts 30Ni5Cu/Al2O3-MgO and 30Ni5Cu/Al2O3-ZnO have much higher H2 selectivity than 30Ni5Cu/Al2O3-SiO2, as well as good coke resistance. H2 selectivity for 30Ni5Cu/Al2O3-MgO catalyst was 73.3% at 450 ℃ and increased to 94.0% at 600℃, whereas for 30Ni5Cu/Al2O3-ZnO catalyst, the H2 selectivity was 63.6% at 450 ℃ and 95.2% at 600℃. TheseAl2O3-MgO and Al2O3-ZnO supported Ni-Cu bimetallic catalysts may have important applications in the production of hydrogen by ethanol steam reforming reactions.

Propane Dehydrogenation over a Commercial Pt-Sn/Al2O3 Catalyst for Isobutane Dehydrogenation： Optimization of Reaction Conditions

The applicability of a commercial Pt-Sn/Al2O3 isobutane dehydrogenation catalyst in dehydrogenation of propane was studied. Catalyst performance tests were carded out in a fixed-bed quartz reactor under different operating conditions. Generally, as the factors improving propane conversion decrease the propylene selectivity, the optimal operating condition to maximize propylene yield is expected. The optimal condition was obtamed by the experimental design method. The investigated parameters were temperature, hydrogen/hydrocarbon （HE/HC） ratio and space velocity, being changed in three levels. Constrains such as the susceptibility of the catalyst components to sintering or phase transformation were also taken into account. Activity, selectivity and stability of the catalyst were considered as the measured response factors, while the space-time-yield （STY） was considered as the variable to be optimized due to its commercial interest. A STY of 16 mol.kg^-1.h^-1 was achieved under the optimal conditions of T= 620 ℃, H2/HC = 0.6 and, weight hourly space velocity （WHSV） = 2.2 h^-1. Single carbon-carbon bond rupture was found to be the main route for the formation of lower hydrocarbon byproducts.

Local structural evolutions of CuO/ZnO/Al2O3 catalyst for methanol synthesis under operando conditions studied by in situ quick X-ray absorption spectroscopy

In situ quick X-ray absorption spectroscopy(QXAFS) at the Cu and Zn K-edge under operando conditions has been used to unravel the Cu/Zn interaction and identify possible active site of CuO/ZnO/Al_2O_3 catalyst for methanol synthesis. In this work, the catalyst, whose activity increases with the reaction temperature and pressure, was studied at calcined, reduced, and reacted conditions. TEM and EDX images for the calcined and reduced catalysts showed that copper was distributed uniformly at both conditions. TPR profile revealed two reduction peaks at 165 and 195 °C for copper species in the calcined catalyst. QXAFS results demonstrated that the calcined form consisted mainly of a mixed Cu O and Zn O, and it was progressively transformed into Cu metal particles and dispersed Zn O species as the reduction treatment. It was demonstrated that activation of the catalyst precursor occurred via a Cu^+intermediate, and the active catalyst predominantly consisted of metallic Cu and Zn O evenunder higher pressures. Structure of the active catalyst did not change with the temperature or pressure, indicating that the role of the Zn was mainly to improve Cu dispersion.This indicates the potential of QXAFS method in studying the structure evolutions of catalysts in methanol synthesis.

Effect of Al_2O_3 Binder on the Precipitated Iron-Based Catalysts for Fischer-Tropsch Synthesis

A series of iron-based Fischer-Tropsch synthesis （FTS） catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characterized by using N2 physical adsorption, temperature-programmed reduction/desorption （TPR/TPD） and MSssbauer effect spectroscopy （MES） methods. The characterization results indicated that the BET surface area increases with increasing Al2O3 content and passes through a maximum at the Al2O3/Fe ratio of 10/100 （weight basis）. After the point, it decreases with further increase in Al2O3 content. The incorporation of Al2O3 binder was found to weaken the surface basicity and suppress the reduction and carburization of iron-based catalysts probably due to the strong K-Al2O3 and Fe-Al2O3 interactions. Furthermore, the H2 adsorption ability of the catalysts is enhanced with increasing Al2O3 content. The FTS performances of the catalysts were tested in a slurry-phase continuously stirred tank reactor （CSTR） under the reaction conditions of 260 ℃, 1.5 MPa, 1000 h^-1 and molar ratio of H2/CO 0.67 for 200 h. The results showed that the addition of small amounts of Al2O3 affects the activity of iron-based catalysts to a little extent. However, with further increase of Al2O3 content, the FTS activity and water gas shift reaction （WGS） activity are decreased severely. The addition of appropriate Al2O3 do not affect the product selectivity, but the catalysts incorporated with large amounts of Al2O3 have higher selectivity for light hydrocarbons and lower selectivity for heavy hydrocarbons.

Simultaneous catalytic hydrolysis of carbonyl sulfide and carbon disulfide over Al_2O_3-K/CAC catalyst at low temperature

In this work, a series of coal-based active carbon （CAC） catalysts loaded by A1203 were prepared by sol-gel method and used for the simulta- neous catalytic hydrolysis of carbonyl sulfide （COS） and carbon disulfide （CS2） at relatively low temperatures of 30-70 ℃. The influences of calcinations temperatures and operation conditions such as： reaction temperature, 02 concentration, gas hourly space velocity （GHSV） and relative humidity （RH） were also discussed respectively. The results showed that catalysts with 5.0 wt% A1203 calcined at 300 ℃ had supe- rior activity for the simultaneous catalytic hydrolysis of COS and CS2. When the reaction temperature was above 50 ℃, catalytic hydrolysis activity of COS could be enhanced but that of CS2 was inhibited. Too high RH could make the catalytic hydrolysis activities of COS and CS2 decrease. A small amount of 02 introduction could enhance the simultaneous catalytic hydrolysis activities of COS and CS2.

Effect of Alumina Particle Size on Ni/Al2O3 Catalysts for p-Nitrophenol Hydrogenation

The catalytic hydrogenation of p-nitrophenol to p-aminophenol was investigated over Ni/Al2O3 catalyst on alumina support with different particle size. It is found that support particle size has significant influences on physiochemical properties and catalytic activity of the resulting Ni/Al2O3 catalyst, but little influence on the selec-tivity. At a comparable amount of Ni loading, the catalytic activity of Ni/Al2O3 prepared with alumina support of smaller particle size is lower. The reduction behavior of the catalyst is a key factor in determining the catalytic activity of Ni/Al2O3 catalyst. The supported nickel catalyst 10.3Ni/Al2O3-3 improves the life span of the membrane by reducing fouling on the membrane surface compared to nano-sized nickel.

Preparation of Fe_2P/Al_2O_3 and FeP/Al_2O_3 catalysts for the hydrotreating reactions

A 60%Fe/Al_2O_3 catalyst was prepared by the co-precipitation method.It was reduced by H_2 to produce metallic Fe,which was then sulfided by CS_2 to Fe_(0.96) S and Fe_3S_4 or phosphided by triphenylphosphine(PPh3) in liquid phases to Fe2 P and Fe P.It was found that the iron sulfides(Fe0.96 S and Fe_3S_4) exhibited the low activity for the hydrodesulfurization(HDS) reactions.The HDS activity was also low on the Fe(metal)/Al_2O_3 and Fe_2 P/Al_2O_3 catalysts since they were converted into Fe0.96 S and Fe_3S_4 during the HDS reactions.In contrast,the FeP/Al_2O_3 was found to be stable and active for the HDS reactions.In particular,Fe P/Al_2O_3 possessed significantly smaller Fe P particles than Fe P/C,leading to the significant higher HDS activity of FeP/Al_2O_3 than Fe P/C.

The nature of the deactivation of hydrothermally stable Ni/SiO2–Al2O3 catalyst in long-time aqueous phase hydrogenation of crude 1,4-butanediol

The deactivation of Ni/SiO2-Al2 O3 catalyst in hydrogenation of crude 1,4-butanediol was investigated.During the operation time of 2140 h,the catalyst showed slow activity decay.Characterization results,for four spent catalysts used at different time,indicated that the main reason of the catalyst deactivation was the deposition of carbonaceous species that covered the active Ni and blocked mesopores of the catalyst.The TPO and SEM measurements revealed that the carbonaceous species included both oligomeric and polymeric species with high C/H ratio and showed sheet.Such carbonaceous species might be eliminated through either direct H2 reduction or the combined oxidation-reduction methodologies.

DBD coupled with MnOx/γ-Al2O3 catalysts for the degradation of chlorobenzene

This paper investigates the degradation of chlorobenzene by dielectric barrier discharge(DBD)coupled with MnOx/γ-Al2O3 catalysts.MnOx/γ-Al2O3 catalysts were prepared using the impregnation method and were characterized in detail by N2 adsorption/desorption,x-ray diffraction and x-ray photoelectron spectroscopy.Compared with the single DBD reactor,the coupled reactor has a better performance on the removal rate of chlorobenzene,the selectivity of COx,and the inhibition of ozone production,especially at low discharge voltages.The degradation rate of chlorobenzene and selectivity of COx can reach 96.3%and 53.0%,respectively,at the specific energy density of 1350 J l-1.Moreover,the ozone concentration produced by the discharge is significantly reduced because the MnOx/Al2O3 catalysts contribute to the decomposition of ozone to form oxygen atoms for the oxidation of chlorobenzene.In addition,based on analysis of the byproducts,the decomposition mechanism of chlorobenzene in the coupled reactor is also discussed.

超细负载型Ni-Mo/Al_2O_3催化剂在渣油加氢裂化中的应用

针对渣油固定床加氢工艺催化剂易结焦失活以及悬浮床加氢工艺催化剂活性偏低的问题,将能悬浮在渣油中的超细负载型催化剂(Ni-Mo/Al2O3)应用于渣油的加氢裂化反应,并在高压釜中考察了反应条件对新疆减压渣油(XJVR)转化率的影响,其中催化剂添加量(质量分数)的考察范围为1%～10%、反应温度为410～450℃、反应时间为0.5～2.5 h、氢气初始压力为5～9 MPa。结果表明,催化剂的添加量对渣油、沥青质以及残炭转化率的影响都很小,但增加催化剂添加量能明显地促进硫的转化,即在此催化体系下,渣油的裂化反应以热反应为主,而加氢脱硫反应则由催化剂的活性中心所决定;反应温度对渣油、残炭、沥青质以及硫的转化率的影响较大,随着反应温度的提高,渣油、残炭、沥青质以及硫的转化率都呈上升的趋势,且前三者的上升趋势更为显著;延长反应时间对反应转化率的影响与提高反应温度所得到的结果类似;当氢气严重过量时,再提高氢气压力对硫转化率没有影响,但可在一定程度上促进残炭和沥青质的加氢反应。

Effects of Cerium Oxide on Ni/Al_2O_3 Catalysts for Decomposition of CH_4 and C_2H_4

Characteristics of carbon deposition of CH 4 and C 2H 4 decomposition over supported Ni and Ni Ce catalysts were studied by using a pulse reaction as well as BET, TPR, XPS and hydrogen chemisorption techniques. It is found that there is a metal semiconductor interaction (MScI) in the Ni Ce catalyst, and the effect of MScI on the carbon deposition of CH 4 decomposition is opposite to that of C 2H 4. A novel model of carbon deposition of CH 4 or C 2H 4 decomposition was proposed.

Characterization and performance of Cu/ZnO/Al_2O_3 catalysts prepared via decomposition of M(Cu,Zn)-ammonia complexes under sub-atmospheric pressure for methanol synthesis from H_2 and CO_2

Methanol synthesis from hydrogenation of CO2 is investigated over Cu/ZnO/Al2O3 catalysts prepared by decomposition of M（Cu,Zn）-ammonia complexes （DMAC） at various temperatures.The catalysts were characterized in detail,including X-ray diffraction,N2 adsorption-desorption,N2O chemisorption,temperature-programmed reduction and evolved gas analyses.The influences of DMAC temperature,reaction temperature and specific Cu surface area on catalytic performance are investigated.It is considered that the aurichalcite phase in the precursor plays a key role in improving the physiochemical properties and activities of the final catalysts.The catalyst from rich-aurichalcite precursor exhibits large specific Cu surface area and high space time yield of methanol （212 g/（Lcat·h）;T=513 K,p=3MPa,SV=12000 h-1）.

H_2-induced CO adsorption and dissociation over Co/Al_2O_3 catalyst

The activation of adsorbed CO is an important step in CO hydrogenation. The results from TPSR of pre-adsorbed CO with H2 and syngas suggested that the presence of H2 increased the amount of CO adsorption and accelerated CO dissociation. The H2 was adsorbed first, and activated to form H＊ over metal sites, then reacted with carbonaceous species. The oxygen species for CO2 formation in the presence of hydrogen was mostly OH^＊, which reacted with adsorbed CO subsequently via CO^＊＋OH^＊ → CO2^＊＋H^＊; however, the direct CO dissociation was not excluded in CO hydrogenation. The dissociation of C-O bond in the presence of H2 proceeded by a concerted mechanism, which assisted the Boudourd reaction of adsorbed CO on the surface via CO^＊＋2H^＊ → CH^＊＋OH^＊. The formation of the surface species （CH） from adsorbed CO proceeded as indicated with the participation of surface hydrogen, was favored in the initial step of the Fischer-Tropsch synthesis.

New technique of comprehensive utilization of spent Al_2O_3-based catalyst

A new technology was developed to recover multiple valuable elements from the spent Al2O3-based catalyst by X-ray phase analysis and exploratory experiments. The experimental results show that in the condition of roasting temperature of 750℃ and roasting time of 30 min, molar ratio of Na2O to Al2O3 of 1.2, the leaching rates of alumina, vanadium and molybdenum in the spent catalyst are 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by precipitators A and B, and the precipitation rates of vanadium and molybdenum are 94.8% and 92.6%. Al（OH）3 was prepared from sodium aluminate solution in the carbonation decomposition process, and the purity of Al2O3 is 99.9% after calcination, the recovery of alumina reaches 90.6% in the whole process; the Ni-Co concentrate was leached by sulfuric acid, a nickel recovery of 98.2% and cobalt recovery over 98.5% can be obtained under the experimental condition of 30% H2SO4, 80℃, reaction time 4 h, mass ratio of liquid to solid 8, stirring rate 800r/min.