High-temperature tribological properties of Ni-P alloy coatings deposited by electro-brush plating

High-temperature tribological properties of Ni-P alloy coatings processed by electro-brush plating on 20CrMo steel have been investigated. A baU-on-disc configuration was employed and 4 mm diameter Si3N4 balls were used as static counterpart. All the wear tests were carried out at 450℃ for 180 rain without lubricants. The electro-brush plating Ni-P coating is amorphous in as-deposited condition, and it becomes polycrystalline with the formation of Ni and Ni3P after heat treatment at 450℃for 1 h. The friction coefficient of the Ni-P coating is just 50% of that of the 20CrMo steel at the friction temperature of 450℃. A mild adhesive wear mechanism was found for the electro-brush plating Ni-P coating tested at 450℃, whereas for the 20CrMo steel at the same temperature a mixed adhesive and abrasive wear mechanism was observed.

Electroless Ni-P plating on Mg-Li alloy by two-step method

Pretreated Mg-Li alloy sheets were pre-plated in a NiCO3？2Ni（OH）2？4H2O solution to form a thin Ni-P alloy film and then plating in a NiSO4？6H2O solution was carried out to obtain a protective coating.The surface morphology,structure and corrosion resistance of the coating were studied.The results showed that a flat,bright and compact plating layer,which was integrated into the matrix metal,was obtained.The P content of the Ni-P coating reached 13.56%（mass fraction）.The hardness value of the Ni-P coating was about HV 549.The polarization curve showed that the corrosion potential of the Ni-P coating reached ？0.249 V（vs SCE）.A long passivation region was found on the polarization curve,and this phenomenon indicated that the coating has an excellent anti-corrosion property.

Electroless plating and growth kinetics of Ni-P alloy film on SiC_p/Al composite with high SiC volume fraction

After Sn/Pd activating, the SiCp/Al composite with 65% SiC (volume fraction) was coated by electroless Ni?P alloy plating. Surface morphology of the composite and its effect on the Ni?P alloy depositing process and bonding action of Ni and P atoms in the Ni?P alloy were studied. The results show that inhomogeneous distribution of the Sn/Pd activating points results in preferential deposition of the Ni?P alloy particles on the Al alloy and rough SiC particle surfaces and in the etched caves. The Ni?P alloy film has an amorphous structure where chemical bonding between Ni and P atoms exists. After a continuous Ni?P alloy film formed, electroless Ni?P alloy plating is not affected by surface morphology and characteristics of the SiCp/Al composite any longer, but by the electroless plating process itself. The Ni?P alloy film follows linear growth kinetics with an activation energy of 68.44 kJ/mol.

Study of Electroless Ni-P-CNTs Composite Plating

The electroless Ni-P-carbon nanotubes composite plating was studied on the copper substrate. Metallurgical microscope, scanning electronic microscope, X-ray diffractometer and micro hardness tester were used to study the structure, constitution and performance of the electroless Ni-P-carbon nanotubes composite deposit. Experiential results show that, with the increment of carbon nanotubes content in electroless plating solution, the grain size on the sample surface decreases whereas the density of grains and the hardness for composite deposit increases. Moreover, adding carbon nanotubes not only improves the degree of crystallization for the composite deposit but also helps their transformation from the amorphous state to the nanocrystal state.

Pretreatment-free Ni-P plating on magnesium alloy at low temperatures

Electrochemically promoted electroless plating(EPEP)was used for the application of pretreatment-free Ni-P coating on AM60B magnesium alloy at low temperatures and the obtained coating was characterized by SEM,AFM,EDS and XRD techniques.Compact,uniform,and medium-phosphorus Ni-P coating with mixed crystalline-amorphous microstructure was obtained by applying a cathodic current density of4mA/cm^2at50℃.Also,island-like nickel clusters were deposited on the alloy surface under the same plating condition but without applying the cathodic current.In addition,the durability of the magnesium alloy against corrosion was strongly improved after plating via EPEP technique which was revealed by electrochemical examinations in3.5%NaCl(mass fraction)corrosive electrolyte.The results of the electrochemical examinations were confirmed by microscopic observations.Thickness,microhardness,porosity and adhesive strength of the deposits were also qualified.

Evaluation of residual stress and corrosion behaviour of electroless plated Ni-P/Ni-Mo-P coatings

Single Ni-P and Ni-Mo-P coatings as well as duplex Ni-P/Ni-Mo-P coatings with the same compositions were prepared by electroless plating.The residual stresses of the coatings on the surface and cross sections were measured by nanoindentation and AFM analysis,and the corrosion behaviour of the coatings in10%HCl solution was evaluated by electrochemical methods,to establish the correlation between the residual stresses and corrosion behaviour of the coatings.The results showed that the single Ni-P and duplex Ni-P/Ni-Mo-P coatings presented residual compressive stresses of241and206MPa respectively,while the single Ni-Mo-P coating exhibited a residual tensile stress of257MPa.The residual compressive stress impeded the growth of the pre-existing porosity in the coatings,protecting the integrity of the coating.The duplex Ni-P/Ni-Mo-P coatings had better corrosion resistance than their respective single coating.In addition,the stress states affect the corrosive form of coatings.

Wear and Corrosion Resistance of Electroless Plating Ni-P Coating on P110 Steel

In order to improve the surface performance and increase the lifetime of P 110 oil casing tube steel during operation, electroless plating was conducted to form Ni-P coating onto its surface. The surface morphology/element distribution and phase constitution of the Ni-P coating were analyzed using scanning electron microscope （SEM） equipped with energy dispersive spectrometry （EDS） and X-ray diffraction （XRD）. Tribological and electrochemical measurement tests were applied to investigate the wear and corrosion resistance of P110 steel and the Ni-P coating. The results showed that a uniform and compact, high phosphorous Ni-P coating was formed. The obtained Ni-P coating indicated certain friction-reduction effect and lower mass loss during friction-wear tests. The Ni-P coating also exhibited higher corrosion resistance in comparison with bared P 110 steel. The obtained N i-P coating has significantly improved the surface performance of P110 steel.

Electrochemical behavior of Cu-Zn-Al shape memory alloy after surface modification by electroless plated Ni-P

The electrochemical behavior of Cu-Zn-Al shape memory alloy (SMA) with andwithout electroless plated Ni-P was investigated by electrochemical methods, in artificial Tyrode'ssolution. The results showed that Cu-Zn-Al SMA engendered dezincification corrosion in Tyrode'ssolution. The anodic active current densities as well as electrochemical dissolution sensitivity ofthe electroless plated Ni-P Cu-Zn-Al SMA increased with NaCl concentration rising, pH of solutiondecreasing and environmental temperature uprising. X-ray diffraction analysis indicated that aftersurface modification by electroless plated Ni-P, an amorphous plated film formed on the surface ofCu-Zn-Al SMA. This film can effectively isolate matrix metal from corrosion media and significantlyimprove the electrochemical property of Cu-Zn-Al SMA in artificial Tyrode's solution.

Investigation on a Non-cyanide Plating Process of Ni-P Coating on Magnesium Alloy AZ91D

In this research we presented a non-cyanide plating process of Ni-P alloy coating on Mg alloy AZ91D. By applying a new process flow of electroless nickel plating in which zinc coating is used as transition of Ni-P coating on Mg alloy AZ91D, the process of copper transition coating plated in the cyanides bath can be replaced. A new bath composed of NiSO4 was established by orthogonal test. The results show that zinc transition coating can increase the adhesion and protect the Mg alloy substrate from the bath corrosion. The optimal plating bath composition is NiSO4·6H2O 20 g/L, NaH2PO2·H2O20g/L and C6H8O7·H2O 2.5 g/L, and optimal bath acidity and optimal plating temperature are pH 4.0 and 95℃, respectively. The present process flow is composed of ultrasonic cleaning→alkaline cleaning→acid pickling→activation→double immersing zinc→electroplating zinc→electroless nickel plating→passivation treatment. The present non-cyanide process of electroless nickel plating is harmless to our surroundings and Ni-P coating on Mg alloy AZ91D produced by present process possesses good adhesion and corrosion resistance.

Preparation and tribological performances of Ni-P-multi-walled carbon nanotubes composite coatings

Multi-walled carbon nanotubes （MWNTs） were wet-milled in the presence of ammonia and cationic surfactant and then used as reinforcements to prepare Ni-P-MWNTs composite coatings by electroless plating. The tribological performances of the composite coatings under dry condition were investigated in comparison with 45 steel and conventional Ni-P coating, Micrographs show that short MWNTs with uniform length and open tips were obtained through the wet-milling process. The results of wear test reveal that the Ni-P-MWNTs composite coatings posses much better friction reduction and anti-wear performances when compared with 45 steel and Ni-P coating. Within the MWNTs content range of 0.74%-1.97%, the friction coefficient and the volume wear rate of the composite coatings decrease gradually and reach the minimum values of 0.08 and 6.22x10-15 m3/（N.m）, respectively. The excellent tribological performances of the composite coatings can be attributed to the introduction of MWNTs, which play both roles of reinforcements and solid lubricant during the wear process.

Characteristics of microstructure and performance of laser-treated electroless Ni-P/Ni-W-P duplex coatings

Characteristics of microstructures of electroless Ni-P/Ni-W-P duplex coatings were investigated using SEM/EDX and XRD analysis techniques. Microhardness and wear behaviour of the coatings before and after laser crystallization were evaluated by measurements of hardnesses of coating surface and cross-section, and by unlubricated friction and wear experiments. The results indicate that it is possible to prepare electroless Ni-P/Ni-W-P duplex coatings by sequential immersion in two different plating baths. After laser crystallization, the microstructures of electroless Ni-P/Ni-W-P duplex coatings present the characteristics of higher degree of crystallization and larger grain size for outer layer Ni-W-P than inner Ni-P, but outer layer has a higher hardness. The wear resistance of laser-treated duplex coatings in a given process parameter conditions is superior to the as-plated ones. Laser treatment was performed directly in air without argon protection, which provides the possibility for application of industrialized production.

Progress of electroplating and electroless plating on magnesium alloy

The current research processes of electroplating and electroless Ni-P alloy plating on magnesium alloys were reviewed. Theoretically,the reason for difficulties in electroplating and electroless plating on magnesium alloys was given.The zinc immersion, copper immersion,direct electroless Ni-P alloy plating and electroplating and electroless plating on magnesium alloys prepared by chemical conversion coating were presented in detail.Especially,the research development of magnesium alloy AZ91 and AZ31 was discussed briefly.Based on the analysis,the existing problems and future research directions were then given.

High-temperature Compressive Performance of Mg Alloy Foams Coated with Ni-P Layer

Mg/Ni hybrid foams were fabricated by the electroless method.The Ni-P(Nickel-Phosphorous)coatings were deposited on the surface of closed-cell Mg alloy foams.The composition,microstructure and phases of the Ni-P coatings were characterized by scanning electron microscopy(SEM),energy-dispersive X-ray spectroscopy(EDS)and X-ray diffraction(XRD),respectively.The compressive tests were performed on the Mg/Ni hybrid foams at 400℃using the Mg alloy foams as a reference.The experimental results show that the yield strength,plateau stress and energy absorption capacity of the closed-cell Mg alloy foams at high temperature were improved by the Ni-P coating.And there are four main modes for the Mg/Ni hybrid foam failure at 400℃,i e,shearing in cell wall,bending in cell edge,shedding and cracking in Ni-P coating.

Effect of additives on nickel-phosphorus deposition obtained by electroless plating:Characterization and corrosion resistance in 3%(mass)sodium chloride medium

Nichel-phosphorus(Ni-P)coatings are deposited on mild steel by using an electroless plating process.The effect of three calix[4]arene derivatives,namely tetra methyl ester-P-tertbutyl calix[4]arene(Calix1),tetra acid-P-tert-butyl calix[4]arene(Calix2)and tetra methyl P-tert-butyl-thicalix[4]arene ester(Calix3)on the deposition rate,the deposit composition,and the morphological surface was investigated and the study of growth mechanisms has delivered useful information about the surface properties of deposit.It is found that these additives modify the deposition rate and the nickel crystallization process.In fact,the Calix1 and Calix3 act as an accelerator,while Calix2 acts as an inhibitor for the nickel electroless.Furthermore,it is shown that the chemical bath is more stable with calix[4]arene derivatives addition and the obtained deposits are compact and adherent.It is observed also that the nickel content increases with additives.On the other hand,the X-ray diffraction showed that the orientation peaks are intensified at{111}in the presence of Calix2,confirming obtained results of EDAX spectrum.The cyclic voltammetry revealed that the tested additives strongly influence the cathodic process and slightly affect the hypophosphite oxidation.Finally,it is found that these compounds improve the anticorrosion efficiency of Ni-P coating on the mild steel substrate in 3%(mass)NaCl,where its polarization resistance increases with Calix2 and Calix3 addition.

Study on the Technology of Ni-P Electroless Plating on the Mg Alloy

Base on the analysis for the corrosion mechanism of the Mg alloys,the technology of Ni-P directly electroless plating on the Mg-10Li-1Zn alloys was studied.The effects of the pre-treatment on the morphologies of substrate and plating films were investigated,The result shows that Ni-P electroless plating could be divided two steps:the induction period and the rapid deposition period.The Ni-P film is amorphous structure:A excellent Ni-P coating can be obtained under the optimal parameter.The Ni-P coating can obviously improve the corrosion resistance of Mg alloy in variety environment.

Influence of heat treatment on microstructures and micro-hardness of n-SiO2/Ni composite coating

The n-SiO2/Ni composite electro-brush plating coating was prepared on the 1045 steel substrate. SEM and TEM were utilized to analyze the surface and cross-section morphologies or the microstructures of the composite coating before and after heat treatment, as well as a micro-hardness tester was used to measure the micro-hardness before and after heat treatment. The results show that the entrance of nano SiO2 particles into composite coating makes the micro-hardness higher. After heat treatment, due to the obstruction to growth of Ni crystals from nano particles, the composite coating still possesses a higher micro-hardness than that of common Ni-base coating.

Preparation and Characterization of Nanosized CeO_2/γ-Al_2O_3 Composite Supports

The main purpose of this article is to use rare earths to modify the electroless plating process for metallizing the surface of quartz optical fibers (silicon fibers). The effects of Yb, Ce and La on the deposition rate of Ni-P, the stability of plating solution and the surface structure of Ni-P film were investigated and their mechanisms were discussed. The surface morphonogies and compositions of the Ni-P films were characterized and analyzed by SEM, MSM, XRD and ESM, respectively. The experimental results showed that Ce(SO4)2 with concentration of 40 mg·L-1 was proved to be the best choice for increasing the deposition rate, enhancing the stability of plating solution and improving the quality of deposited Ni-P film compared with the other two kind of rare earths. The detections of ESM exhibited no effect of Ce on film compositions and no Ce deposition being found in the film prepared by electroless plating with adding Ce because of its much more negative deposition potential than those of the reducing agents used in the experiment. The addition of Ce resulted in a transmission of the film surface structure from crystal structure into a microcrystallitic structure. The Ni-P film with thickness of about 45 μm prepared using electroless plating by adding Ce(SO4)2 with concentration of 40 mg·L-1 had good quality, which will be satisfactorily for the next Ni deposition by electroplating.

Research on improvement of electrode efficiency of water electrolysis on Ni-P electroless plating by appended RE

Research on rare earth(RE) improved electrolytic efficiency of water electrolysis by electrode based on Ni-P coating was discussed.The result of research proved that efficiency of water electrolysis of the electrode was dramatically improved when a few of RE were added in plating tank.Moreover,it showed that La appended in the tank was more effective than Ce appended in the tank.Besides that,this article illustrated positive impact of RE on process of plating as well as effect of RE on microstructure of the Ni-P coating,composition of the plating and corrosion resistance of surface of the coating.Furthermore,argumentation extended to it that RE alone and compound of La and Ce had effect on efficiency of hydrogen production by water electrolysis process.At the last part of the article,it was shown that a new mechanism was presented in a new angle being established in effect of RE on electron state of Ni plating.

重整装置预加氢产物后冷器泄漏分析

华北石化公司130万吨/年重整装置2019年开工投产,分为石脑油加氢、重整、催化剂再生、重整产物后分馏以及公用工程几个部分。其中,预加氢处理的目的是为了给重整反应提供馏程和杂质含量都合格的原料,采用全馏分加氢,先汽提后分馏的工艺流程,拔头油中不含硫、氮。该装置预加氢产物后冷器E103A/B开工后,运行2个月发现管束内漏,在循环水侧放空导淋有石脑油可以排出,随后将管程切出,避免浊度超标对循环水场造成影响。2020年6月,预加氢处理单元停工,对该换热器管束进行更换。本文对抽出管束泄漏情况进行了分析,以便对相同工况的设备提供参考。

Morphologies and corrosion resistances of electroless Ni-P coated nanoporous coppers

In order to improve the corrosion resistance of nanoporous coppers （NPCs）, the electroless Ni-P coated NPCs were prepared in plating solutions with different pH values （5, 8, 11） and complexing agent （actic acid, citric acid）. The morphologies and cor- rosion resistances of the as-prepared samples were investigated. The results showed that the double complexing agent com- posed of lactic acid and citric acid is relatively suitable for preparing the Ni-P coated NPC with three-dimensional continuous interpenetrating ligament-channel structures, and the uniform ligaments and nanoporous channels could be obtained at pH8. The Ni-P coated NPC showed higher corrosion potentials than NPC in H2S04, NaOH and NaC1 corrosion solutions.