The selective catalytic hydrogenation of naphthalene to high-value tetralin was systematically investigated.A series of Al2O3 catalysts containing different active metals(Co,Mo,Ni,W)were prepared by incipient wetness ...The selective catalytic hydrogenation of naphthalene to high-value tetralin was systematically investigated.A series of Al2O3 catalysts containing different active metals(Co,Mo,Ni,W)were prepared by incipient wetness impregnation.The effects of different active metals forms(oxidation,reduction,sulfuration)and reaction conditions on naphthalene hydrogenation were investigated and the catalysts were characterized by XRD,XPS,BET,NH3-TPD and SEM.Especially,Ni-Mo/Al2O3 was first used in this reactive system.The results show that the oxidative4%Ni O-20%MoO3/Al2O3 is the best catalyst for the preparation of tetralin.The conversion of naphthalene and the selectivity of tetralin can reach 95.62%and 99.75%respectively at 200℃,8 h and 6 MPa.Compared with reduced and sulfureted 4%Ni O-20%MoO3/Al2O3 catalysts,oxidative 4%Ni O-20%MoO3/Al2O3 has a well dispersed and uniform monolayer of the active metals,larger pore volume and size,and larger total acidity.NiO-MoO3/Al2O3 has a synergistic effect between NiO activity and MoO3 selectivity.展开更多
The influence of cathodic pulse parameters was evaluated on plasma electrolytic oxidation(PEO)coatings grown on 7075 aluminum alloy in a silicate-based electrolyte containing potassium titanyl oxalate(PTO)using pulsed...The influence of cathodic pulse parameters was evaluated on plasma electrolytic oxidation(PEO)coatings grown on 7075 aluminum alloy in a silicate-based electrolyte containing potassium titanyl oxalate(PTO)using pulsed bipolar waveforms with various cathodic duty cycles and cathodic current densities.The coatings were characterized by SEM,EDS,and XRD.EIS was applied to investigate the electrochemical properties.It was observed that the increase of cathodic duty cycle and cathodic current density from 20%and 6 A/dm^(2) to 40%and 12 A/dm^(2) enhances the growth rate of the inner layer from 0.22 to 0.75μm/min.Adding PTO into the bath showed a fortifying effect on influence of the cathodic pulse and the mentioned change of cathodic pulse parameters,resulting in an increase of the inner layer growth rate from 0.25 to 1.10μm/min.Based on EDS analysis,Si and Ti were incorporated dominantly in the upper parts of the coatings.XRD technique merely detectedγ-Al_(2)O_(3),and there were no detectable peaks related to Ti and Si compounds.However,the EIS results confirmed that the incorporation of Ti^(4+)into alumina changed the electronic properties of the coating.The coatings obtained from the bath containing PTO using the bipolar waveforms with a cathodic duty cycle of 40%and current density values higher than 6 A/dm^(2) showed highly appropriate electrochemical behavior during 240 d of immersion due to an efficient repairing mechanism.Regarding the effects of studied parameters on the coating properties,the roles of cathodic pulse parameters and PTO in the PEO process were highlighted.展开更多
Silane coupling agent KH560 was used to modify the surface of nano-α-Al<sub>2</sub>O<sub>3</sub> in ethanol-aqueous solution with different proportions. The particle size of nano-α-Al<sub&...Silane coupling agent KH560 was used to modify the surface of nano-α-Al<sub>2</sub>O<sub>3</sub> in ethanol-aqueous solution with different proportions. The particle size of nano-α-Al<sub>2</sub>O<sub>3</sub> was determined by nano-particle size analyzer, and the effects of nano-α-Al<sub>2</sub>O<sub>3</sub> content, ethanol-aqueous solution ratio and KH560 dosage on the dispersion and particle size of nano-α-Al<sub>2</sub>O<sub>3</sub> were investigated. The material structure before and after modification was determined by Fourier transform infrared spectroscopy (FTIR). Aqueous polyurethane resin and inorganic components are combined with modified nano-α-Al<sub>2</sub>O<sub>3</sub> dispersion to form chromium-free passivation solution. The solution is coated on the galvanized sheet, the adhesion and surface hardness are tested, the bonding strength of the coating and the surface hardness of the substrate are discussed. The corrosion resistance and surface morphology of the matrix were investigated by electrochemical test, neutral salt spray test and scanning electron microscope test. The chromium-free passivation film formed after the modification of nano-α-Al<sub>2</sub>O<sub>3</sub> increases the surface hardness of galvanized sheet by about 85%. The corrosion resistance of the film is better than that of a single polyurethane film. The results show that the surface hardness and corrosion resistance of polyurethane resin composite passivation film are significantly improved by the introduction of nano-α-Al<sub>2</sub>O<sub>3</sub>.展开更多
基金supported by the Joint Funds of National Key R&D Program of China(2018YFB0604603)the National Natural Science Foundation of China(21536009,21776229)+2 种基金Science and Technology Plan Projects of Shaanxi Province(2017ZDCXL-GY-10-03,2018ZDXMGY-167)The Young Science and Technology Star Project of Shaanxi Province(2017KJXX-62)Science and Technology Program of Yulin(2018-2-22)。
文摘The selective catalytic hydrogenation of naphthalene to high-value tetralin was systematically investigated.A series of Al2O3 catalysts containing different active metals(Co,Mo,Ni,W)were prepared by incipient wetness impregnation.The effects of different active metals forms(oxidation,reduction,sulfuration)and reaction conditions on naphthalene hydrogenation were investigated and the catalysts were characterized by XRD,XPS,BET,NH3-TPD and SEM.Especially,Ni-Mo/Al2O3 was first used in this reactive system.The results show that the oxidative4%Ni O-20%MoO3/Al2O3 is the best catalyst for the preparation of tetralin.The conversion of naphthalene and the selectivity of tetralin can reach 95.62%and 99.75%respectively at 200℃,8 h and 6 MPa.Compared with reduced and sulfureted 4%Ni O-20%MoO3/Al2O3 catalysts,oxidative 4%Ni O-20%MoO3/Al2O3 has a well dispersed and uniform monolayer of the active metals,larger pore volume and size,and larger total acidity.NiO-MoO3/Al2O3 has a synergistic effect between NiO activity and MoO3 selectivity.
文摘The influence of cathodic pulse parameters was evaluated on plasma electrolytic oxidation(PEO)coatings grown on 7075 aluminum alloy in a silicate-based electrolyte containing potassium titanyl oxalate(PTO)using pulsed bipolar waveforms with various cathodic duty cycles and cathodic current densities.The coatings were characterized by SEM,EDS,and XRD.EIS was applied to investigate the electrochemical properties.It was observed that the increase of cathodic duty cycle and cathodic current density from 20%and 6 A/dm^(2) to 40%and 12 A/dm^(2) enhances the growth rate of the inner layer from 0.22 to 0.75μm/min.Adding PTO into the bath showed a fortifying effect on influence of the cathodic pulse and the mentioned change of cathodic pulse parameters,resulting in an increase of the inner layer growth rate from 0.25 to 1.10μm/min.Based on EDS analysis,Si and Ti were incorporated dominantly in the upper parts of the coatings.XRD technique merely detectedγ-Al_(2)O_(3),and there were no detectable peaks related to Ti and Si compounds.However,the EIS results confirmed that the incorporation of Ti^(4+)into alumina changed the electronic properties of the coating.The coatings obtained from the bath containing PTO using the bipolar waveforms with a cathodic duty cycle of 40%and current density values higher than 6 A/dm^(2) showed highly appropriate electrochemical behavior during 240 d of immersion due to an efficient repairing mechanism.Regarding the effects of studied parameters on the coating properties,the roles of cathodic pulse parameters and PTO in the PEO process were highlighted.
文摘Silane coupling agent KH560 was used to modify the surface of nano-α-Al<sub>2</sub>O<sub>3</sub> in ethanol-aqueous solution with different proportions. The particle size of nano-α-Al<sub>2</sub>O<sub>3</sub> was determined by nano-particle size analyzer, and the effects of nano-α-Al<sub>2</sub>O<sub>3</sub> content, ethanol-aqueous solution ratio and KH560 dosage on the dispersion and particle size of nano-α-Al<sub>2</sub>O<sub>3</sub> were investigated. The material structure before and after modification was determined by Fourier transform infrared spectroscopy (FTIR). Aqueous polyurethane resin and inorganic components are combined with modified nano-α-Al<sub>2</sub>O<sub>3</sub> dispersion to form chromium-free passivation solution. The solution is coated on the galvanized sheet, the adhesion and surface hardness are tested, the bonding strength of the coating and the surface hardness of the substrate are discussed. The corrosion resistance and surface morphology of the matrix were investigated by electrochemical test, neutral salt spray test and scanning electron microscope test. The chromium-free passivation film formed after the modification of nano-α-Al<sub>2</sub>O<sub>3</sub> increases the surface hardness of galvanized sheet by about 85%. The corrosion resistance of the film is better than that of a single polyurethane film. The results show that the surface hardness and corrosion resistance of polyurethane resin composite passivation film are significantly improved by the introduction of nano-α-Al<sub>2</sub>O<sub>3</sub>.
