Discussion on New Evaluation Technology of Non-Metallic Composite Continuous Pipe for Oil and Gas Field

In view of the serious lack and lag of the test and evaluation technology of non-metallic composite continuous pipe, and focusing on the characteristics of the application of non-metallic composite continuous pipe in oil field, this paper discusses a series of new full-scale test and evaluation technologies for accurately evaluating the product quality and practical application performance of non-metallic composite continuous pipe, which effectively solves the major technical problem that the new products of non-metallic pipe cannot be accurately evaluated. Based on the characteristics of the application of non-metallic composite continuous pipe in oil field, a series of new full-scale test evaluation technologies which can accurately evaluate the product quality and practical application performance of non-metallic pipe are designed through a large number of tests. The test and evaluation technology can accurately evaluate the key performance of high and low pressure cycle, high and low temperature cycle, gas permeability resistance, minimum bending radius etc. It provides a scientific evaluation basis for the standardized application of non-metallic continuous pipe and a reliable quality control method for the selection of products in oil field.

Rise of quantum correlations in non-Markovian environments in continuous-variable systems

We investigate the time evolution of quantum correlations, which are measured by Gaussian quantum discord in a continuous-variable bipartite system subject to common and independent non-Markovian environments. Considering an initial two-mode Gaussian symmetric squeezed thermal state, we show that quantum correlations can be created during the non-Markovian evolution, which is different from the Markovian process. Furthermore, we find that the temperature is a key factor during the evolution in non-Markovian environments. For common reservoirs, a maximum creation of quantum correlations may occur under an appropriate temperature. For independent reservoirs, the non-Markovianity of the total system corresponds to the subsystem whose temperature is higher. In both common and independent environments, the Gaussian quantum discord is influenced by the temperature and the photon number of each mode.

Development of Optimal Maintenance Policies for Offshore Wind Turbine Gearboxes Based on the Non-homogeneous Continuous-Time Markov Process

Gearbox in offshore wind turbines is a component with the highest failure rates during operation. Analysis of gearbox repair policy that includes economic considerations is important for the effective operation of offshore wind farms. From their initial perfect working states, gearboxes degrade with time, which leads to decreased working efficiency. Thus, offshore wind turbine gearboxes can be considered to be multi-state systems with the various levels of productivity for different working states. To efficiently compute the time-dependent distribution of this multi-state system and analyze its reliability, application of the nonhomogeneous continuous-time Markov process(NHCTMP) is appropriate for this type of object. To determine the relationship between operation time and maintenance cost, many factors must be taken into account, including maintenance processes and vessel requirements. Finally, an optimal repair policy can be formulated based on this relationship.

CONSTRUCTION OF SOME KIESSWETTER-LIKE FUNCTIONS-THE CONTINUOUS BUT NON-DIFFERENT-IABLE FUNCTION DEFINED BY QUINARY DECIMAL

In this paper, we construct some continuous but non-differentiable functions defined by quinary dec-imal, that are Kiesswetter-like functions. We discuss their properties, then investigate the Hausdorff dimensions of graphs of these functions and give a detailed proof.

THE CONTINUOUS CASTING PROBLEM WITH NON-EQUILIBRIUM CONDITIONS

We establish the existence and uniqueness of classical solutions of the continuous casting problem with surface tension and kinetic conditions in a short time interval.

Non-metallic Inclusions in Continuously Cast Aluminum Killed Steels

In aluminum killed steels, the size, shape, quantity and formation of non-metallic inclusions in ladle steel (before and after RH vacuum treatment) and in tundish as well as in slabs were studied by EPMA (Electron Probe Microanalysis) and by analyzing the total oxygen. The results showed that in the slabs the total oxygen was quite low and the inclusions discovered were mainly small-sized angular alumina inclusions. This indicates that most inclusions have been removed by floating out during the continuous casting process. In addition, the countermeasures were discussed to decrease the alumina inclusions in the slabs further.

Production of 48MnV-C non-heat treatment crankshaft steel by means of converter plus continuous casting and hot-rolling process

48MnV-C non-heat treatment crankshaft steel is specially used for making crankshafts of Cummings C engines.It mainly adopts the technology of V—N micro-alloying,at present,it has been successfully used in making crankshaft of heavy duty truck engines.BX STEEL made trial production by means of converter→secondary metallurgy(RH + LF)→rectangular slab caster→hot rolling process,and studied the T[O],T[N],[H]and non-metal inclusion in 48MnV - C steel under continuous casting process condition,the actual grain size and the slab quality.All the chemical compositions and test results met the needs of Cummings Crankshaft Steel Standard.In order to ensure the mechanical properties of the non-heat treatment steel,a certain amount of nitrogen is added to it,also a small amount of sulfur is added to improve the cutting property of the steel.This process route can make full use of the de-hydrogen function of RH,and during RH treatment,rough adjustment of alloy elements may be made while the adjustment of Nitride Manganese nitrogen pick up and adjusting Mn,as well as Ca treatment and S content adjustment may be done during LF treatment so as to ensure the requirement of high nitrogen,low hydrogen,low oxygen content in 48MnV-C steel.Magnetic marks are defects shown in magnetic powder testing after the steel was used to make finished crankshafts.The 48MnV - C non-heat treatment crankshaft steel produced by means of the above-mentioned process route has not only relatively high robust performance which meets the needs of truck crankshaft safety,but also high qualification rate and basically no "magnetic marks" are found after being made into finished crankshafts,which meets the crankshaft standard.Therefore,this steel has been widely used in domestic crankshaft industry.

Microstructure and properties of Al-0.70Fe-0.24Cu alloy conductor prepared by horizontal continuous casting and subsequent continuous extrusion forming

A novel process for manufacturing A1-0.70Fe-0.24Cu alloy conductor was proposed, which includes horizontal continuous casting and subsequent continuous extrusion forming （Conform）. The mechanical properties, electrical conductivity and the compressed creep behaviour of the alloy were studied. The results indicate that the Conform process induces obvious grain refinement, strain-induced precipitation of AI7CuzFe phase and the transformation of crystal orientation distribution. The processed alloy has good comprehensive mechanical properties and electrical conductivity. Moreover, a better creep resistance under the conditions of 90 ~C and 76 MPa is shown compared with pure A1 and annealed copper, and the relationship between primary creep strain and time may comply with the logarithmic law. The enhanced properties are attributed to the grain refinement as well as the fine and homogeneously distributed thermally stable A1Fe and A17Cu2Fe precipitation phases.

Process for improving the ladle free- opening rate for high aluminum steel in continuous casting

Steel 20Mn23AlV is a type of high aluminum steel with a very low ladle free-opening rate. The aluminum composition of 20Mn23AlV ranges from 1.6% to 2.45% ,which is significantly higher than other types of steel. According to the real condition of 40 t ladle in steel-making plant of Baosteel Special Steel Company, previous works show that the key factors affecting the ladle free-opening rate of high aluminum steel in continuous casting are：sand material, accessories baking, ladle nozzle cleaning, the process and amount of adding sand, and the rate of argon stirring during refining. Therefore, improving the ladle filler sand quality, baking all of the raw materials, controlling the addition of ladle filler sand, cleaning the ladle nozzle, and optimizing argon stirring during the refining process can resolve the problem of a low ladle free-opening rate of high aluminum steel caused by the long ladle time of liquid steel.

Numerical study on three-dimensional flow field of continuously rotating detonation in a toroidal chamber

Gaseous detonation propagating in a toroidal chamber was numerically studied for hydrogen/oxygen/nitrogen mixtures. The numerical method used is based on the three-dimensional Euler equations with detailed finiterate chemistry. The results show that the calculated streak picture is in qualitative agreement with the picture recorded by a high speed streak camera from published literature. The three-dimensional flow field induced by a continuously rotating detonation was visualized and distinctive features of the rotating detonations were clearly depicted. Owing to the unconfined character of detonation wavelet, a deficit of detonation parameters was observed. Due to the effects of wall geometries, the strength of the outside detonation front is stronger than that of the inside portion. The detonation thus propagates with a constant circular velocity. Numerical simulation also shows three-dimensional rotating detonation structures, which display specific feature of the detonation- shock combined wave. Discrete burning gas pockets are formed due to instability of the discontinuity. It is believed that the present study could give an insight into the interest- ing properties of the continuously rotating detonation, and is thus beneficial to the design of continuous detonation propulsion systems.

Optimization of Process Parameters of Continuous Microwave Drying Raspberry Puree Based on RSM and ANN-GA

To improve drying uniformity and anthocyanin content of the raspberry puree dried in a continuous microwave dryer,the effects of process parameters(microwave intensity,air velocity,and drying time)on evaluation indexes(average temperature,average moisture content,average retention rate of the total anthocyanin content,temperature contrast value,and moisture dispersion value)were investigated via the response surface method(RSM)and the artificial neural network(ANN)with genetic algorithm(GA).The results showed that the microwave intensity and drying time dominated the changes of evaluation indexes.Overall,the ANN model was superior to the RSM model with better estimation ability,and higher drying uniformity and anthocyanin retention rate were achieved for the ANN-GA model compared with RSM.The optimal parameters were microwave intensity of 5.53 W•g^(-1),air velocity of 1.22 m·s^(-1),and drying time of 5.85 min.This study might provide guidance for process optimization of microwave drying berry fruits.

Improved continuous precipitation kinetics and tensile properties of extruded AZ80 alloy through {10-12} twin formation

This study investigates the effect of{10-12}deformation twins on the continuous precipitation behavior of an extruded Mg-8.0Al-0.5Zn-0.2Mn(AZ80)alloy during aging.The extruded AZ80 alloy is compressed along the transverse direction to introduce{10-12}twins,followed by an aging treatment at 300℃.The extruded material exhibits a twin-free microstructure with low internal strain energy,whereas the pre-twinned material possesses abundant{10-12}twins and has high internal strain energy.The aging results reveal that the peak-aging time of the pre-twinned material(1 h)is one-eighth of that of the extruded material(8 h).Although Mg_(17)Al_(12)continuous precipitates(CPs)are observed in both the peak-aged materials,these CPs are much smaller and more densely distributed in the pre-twinned material despite the significantly shorter aging time.The CPs size in the peak-aged materials increases in the following order:twinned region in the pre-twinned material(0.47μm)<residual matrix region in the pre-twinned material(1.71μm)<matrix region in the extruded material(2.55μm).Moreover,the CPs number density in the twinned region of the pre-twinned material is approximately 11 times higher than that in the matrix region of the extruded material.The peak-aged pre-twinned material exhibits significantly higher tensile strength and ductility than the peak-aged extruded material.These results demonstrate that the formation of{10-12}twins in the extruded AZ80 alloy substantially accelerates the static precipitation of CPs during aging at 300℃and improves the tensile properties of the peak-aged material.

Tripartite continuous-variable entanglement of NOPA system

We investigate the fundamental limits to the achievable tripartite continuous-variable （CV） entanglement criterion of a generalized Vl criterion. Our numerical simulation results show that the non-degenerate eigenvalues do effect the performances of the estimated minimum variances. From below the threshold to above the threshold, with the increase of the pump parameter, the tripartite CV entanglement gradually disappears. The different off-diagonal elements seriously distort the weights for entanglement. We can obtain a good tripartite CV entanglement by appropriately controlling the values of off-diagonal elements eij.

Application of LRB isolation technology in continuous girder bridges

This paper summarizes the superiority of lead-rubber beating （LRB） continuous girder bridges. The research method for isolation performance is discussed when pile-soil interaction is considered. By the finite element method and self-compiling program, a systematic study of the reliability of LRB continuous girder bridges is given by the use of different indicators, including the riding comfort of the LRB system, the pounding and dynamic stability when the LRB system is subjected to seismic excitations, and the reliability of the LRB system when subjected to other common horizontal loads. The results show that the LRB system has obvious advantages over the traditional continuous girder structure. The LRB isolation effect remains good even when pile-soil interaction is considered; the vertical rigidity of the LRB guarantees desirable riding comfort. The LRB demonstrates good reliability when subjected to the effects of braking, wind loads and temperature. However, it is also pointed out that the pounding of the LRB system subjected to earthquakes must be avoided, and the dynamic stability may be reduced when the LRB system has higher piers and generates a larger displacement in a strong earthquake. Useful advice and guidance are proposed for engineering application.

肥胖儿童non-HDL-C、remnant cholesterol与亚临床动脉粥样硬化的关系

目的:了解non-HDL-C和remnant cholesterol与肥胖儿童亚临床动脉粥样硬化(AS)的关系。方法:根据甘油三酯(TG)水平将65例肥胖儿童(肥胖组)分为I组(TG≥2.3 mmol/L)32例,II组(TG<2.3 mmol/L)33例,与肥胖组儿童性别年龄相匹配的正常体质量儿童30例为III组(对照组)。比较3组儿童血脂指标,对肥胖组各项血脂指标与血浆致动脉粥样硬化指数(AIP)进行相关性分析,肥胖患儿体质指数、血脂指标与颈动脉内径、内膜-中层厚度(c-IMT)、血流参数进行相关性分析。结果:I组、II组的TG、总胆固醇(TC)、低密度脂蛋白胆固醇(LDL-C)、non-HDL-C、remnant cholesterol、AIP均较对照组升高,高密度脂蛋白胆固醇(HDL-C)较对照组降低,且I组的remnant cholesterol、AIP均较II组升高。肥胖组儿童AIP与TG、non-HDL-C、remnant cholesterol呈正相关,与HDL-C呈负相关。37例行颈动脉超声检查的肥胖儿童的c-IMT较正常儿童的增厚。结论:non-HDL-C、remnant cholesterol在肥胖儿童亚临床AS中有重要作用,在肥胖儿童血脂异常的治疗中应关注non-HDL-C、remnant cholesterol的变化。

Shenqi Fuzheng injection combined with GP chemotherapy in the treatment of advanced non-small cell lung cancer： a meta-analysis

Objective： To evaluate the clinical efficacy of Shenqi Fuzheng injection combined with gemcitabine plus cisplatin（GP） in the treatment of advanced non-small cell lung cancer （NSCLC）. Methods： we performed a systematicsearch in the electronic databases such as Cochrane Library, Pubmed, Embase, Chinese Journal Full-text Database,Chinese Biomedical Literature Database, Chinese Science and Technology Periodical Full-text Database andWanfang Database up to 30 January 2017. Randomized controlled trials （RCT） of Shenqi Fuzheng Injectioncombined with GP chemotherapy in the treatment of advanced NSCLC were searched, and all the RCTs wereconducted on methodological quality assessment. Data extraction and data analysis were according to standards ofCochrane systematic review. Results： Eight trials were included including a total of 701 patients. Meta-analysisresults： Shenqi Fuzheng injection combined with GP chemotherapy could significantly improve the functionalstatus of patients with NSCLC （OR = 3.44, 95% CI [2.26, 5.25], P 〈 0.0001） and clinical treatment efficacy （OR =（OR = 0.31, 95%CI [0.20, 0.47], P 〈 0.0001. The rate of leukopenia （OR = .31, 95%CI [0.20,0.47], P 〈 0.0001）,thrombocytopenia （OR = 0.58, 95%CI [0.37, 0.91], P = 0.020）, hemoglobin decline （（OR = 0.31, 95%CI [0.16,0.59], P = 0.0004） and incidence of gastrointestinal reactions （OR = 0.58,P 〈 0.05） could be reduced. Conclusion：Shenqi Fuzheng injection combined with GP chemotherapy in the treatment of advanced NSCLC obtainedsignificantly clinical efficacy. The quality of the literature incorporated is low, the conclusion requires high-qualityresearch to further prove.

NC-OFDM雷达通信一体化设计

雷达通信一体化有利于提高设备硬件资源利用率和频谱利用率,已成为近年来的研究热点。针对目前频谱资源稀缺的情况,结合认知无线电的概念,提出了基于非连续正交频分复用(NC-OFDM)的雷达通信一体化设计,对NC-OFDM雷达通信一体化信号测量目标特征进行了距离及速度的估计,并对基于NC-OFDM雷达通信一体化信号模糊函数、雷达成像的距离分辨率和方位分辨率、自相关性及误码率进行了分析,同时,选取互信息作为指标,利用优化算法进行波形设计。仿真结果表明,NC-OFDM雷达通信一体化信号具有较好的雷达探测性能和更为优良的无线通信性能。

THEORETICAL STUDY OF AN OSCILLATING WAVEFORM FUNCTION AND PARAMETERS FOR CONTROLLING THE NON-SINUSOIDAL OSCILLATION OF A MOLD

A new non-sinusoidal oscillation waveform is constructed for controlling themold oscillation during continuous casting. Casting velocity and oscillation parameters are thenestablished for a computer model of the continuous casting process. The waveform distortioncoefficient ? of waveform function is close to the waveform distortion rate a, so s is taken for awhen the basic parameters are selected initially. The waveform function can be created for the servohydraulic system or the mechanical driving system. Industrial scale experiments show the waveformfunction is effective.

Design and Experimental Research on Seedling Pick-Up Mechanism of Planetary Gear Train with Combined Non-circular Gear Transmission

Currently, transplanting mechanisms for dryland plug seedlings in China are mainly semiautomatic and have low efficiency. The rotary seedling pick-up mechanism with a planetary gear train for non-uniform intermittent transmission, and a concave and convex locking arc device, has a large rigid impact. To solve these problems, according to the design requirements for a dryland plug seedling transplanting mechanism, a rotary seedling pick-up mechanism of a planetary gear train with combined non-circular gear transmission of incomplete eccentric circular and noncircular gears was proposed. This has the characteristics of two-times greater fluctuation of the transmission ratio in a cycle, and can achieve a non-uniform continuous drive. Through analysis of the working principle of the seedling pick-up mechanism, its kinematics model was established. The human–computer interaction optimization method and self-developed computer-aided analysis and optimization software were used to obtain a set of parameters that satisfy the operation requirements of the seedling pick-up mechanism. According to the optimized parameters, the structure of the seedling pick-up mechanism was designed, a virtual prototype of the mechanism was created, and a physical prototype was manufactured. A virtual motion simulation of the mechanism was performed, high-speed photographic kinematics tests were conducted, and the kinematic properties of the physical prototype were investigated, whereby the correctness of the theoretical model and the optimized design of the mechanism were verified. Further, laboratory seedling pick-up tests were conducted. The success ratio of seedling pick-up was 93.8% when the seedling pick-up efficiency of the mechanism was 60 plants per minute per row, indicating that the mechanism has a high efficiency and success ratio for seedling pick-up and can be applied to a dryland plug seedling transplanter.

Motion Stability Analysis of Non-sinusoidal Oscillation of Mold Driven by Servomotor

The investments of the electro-hydraulic servo system of the mold non-sinusoidal oscillator are great, the modification ratio of the mechanical type is unable to be adjusted online, and some continuous casters suffer from server resonance during the casting. A mold non-sinusoidal oscillation mechanism driven by servomotor is proposed and the prototype is produced in the lab, the investment is low and the modification ratio is can be adjusted online, and the stability problem is studied. At first the dynamics model of the servomotor non-sinusoidal oscillation is established, and the kinematics differential function is deduced. Furthermore, based on the harmonic balance method, the eigenvalues of the system are solved; the criterion of the stability of the system is put forward. In addition, the eigenvalues and harmonic with different oscillating parameters are analyzed. Analytical results show that the real parts of the eigenvalues are positive, the system will be unstable, and the resonance will occur when the positive real parts of the eigenvalues are extremum. A foundation is established for solving the running smooth problem and next application of this mechanism.