Experimental study on tensile deformation behaviors under room and elevated temperatures induced by microstructure inhomogeneity of ZK60 Mg with a longitudinal weld

The tensile tests of the extruded ZK60 Mg containing a longitudinal weld seam were carried out at room and elevated temperatures, and the effects of induced microstructure inhomogeneity on tensile deformation behavior was clarified. The results show that the deformation mode, dynamic recrystallization(DRX), texture evolution and mechanical properties are strongly affected by the longitudinal weld seam,temperature, and loading direction. The room temperature(RT) deformation of welding zone is controlled by the dislocation slips with the association of some twins, while twinning plays significant roles in the accommodation of c-axis strain of the coarse grains on matrix zone.The deformation at RT stretched along extrusion direction(ED) and transverse direction(TD) are controlled by basal slip/twinning and basal slip/prismatic slip/twinning, respectively. During high temperature tension, the dislocation cross slip of pyramidal slip is activated, and grain boundary sliding occurred in welding zone, leading to the superplastic behavior. With the increase of tensile temperature, the predominant DRX mode is transformed from continuous DRX to discontinuous DRX. Moreover, the basal poles of the grains spread from TD towards ED with the decrease of maximum pole intensity when stretched along ED, while non-basal textures are transformed to (10-10) fiber texture when stretched along TD. The slip-dominated flow is seen during RT tension along ED, while twinning becomes predominant during RT tension along TD. The fine grain structure causes the superior RT tensile properties along ED of welding zone with ultimate tensile strength of 315 MPa and elongation to failure of 13.8%. With the increase of tensile temperature, the slipping-dominated deformation is transformed into twinning-dominated, causing the decrease of strength and increase of elongation.

Spatial Inhomogeneity of Atmospheric CO_(2) Concentration and Its Uncertainty in CMIP6 Earth System Models

This paper provides a systematic evaluation of the ability of 12 Earth System Models(ESMs)participating in the Coupled Model Intercomparison Project Phase 6(CMIP6)to simulate the spatial inhomogeneity of the atmospheric carbon dioxide(CO_(2))concentration.The multi-model ensemble mean(MME)can reasonably simulate the increasing trend of CO_(2) concentration from 1850 to 2014,compared with the observation data from the Scripps CO_(2) Program and CMIP6 prescribed data,and improves upon the CMIP5 MME CO_(2) concentration(which is overestimated after 1950).The growth rate of CO_(2) concentration in the northern hemisphere(NH)is higher than that in the southern hemisphere(SH),with the highest growth rate in the mid-latitudes of the NH.The MME can also reasonably simulate the seasonal amplitude of CO_(2) concentration,which is larger in the NH than in the SH and grows in amplitude after the 1950s(especially in the NH).Although the results of the MME are reasonable,there is a large spread among ESMs,and the difference between the ESMs increases with time.The MME results show that regions with relatively large CO_(2) concentrations(such as northern Russia,eastern China,Southeast Asia,the eastern United States,northern South America,and southern Africa)have greater seasonal variability and also exhibit a larger inter-model spread.Compared with CMIP5,the CMIP6 MME simulates an average spatial distribution of CO_(2) concentration that is much closer to the site observations,but the CMIP6-inter-model spread is larger.The inter-model differences of the annual means and seasonal cycles of atmospheric CO_(2) concentration are both attributed to the differences in natural sources and sinks of CO_(2) between the simulations.

Analysis of inhomogeneity of solidified microstructure of continuous casting copper tubular billet based on factor analysis

The horizontal continuous casting process,the initial step in TP2 copper tubular processing,directly determines the microstructure and properties of copper tubular.However,the process parameters of the continuous casting characterize time variation,multiple disturbances and strong coupling.As a consequence,their influence on a casting billet is difficult to be determined.Due to the above issues,the common factor and special factor analysis of the factor analysis model were used in this study,and the casting experiment and billet metallographic experiment were carried out to diagnose and analyze the reason of the microstructure inhomogeneity.The multiple process parameters were studied and classified using common factor analysis,2 the cast billets with abnormal microstructures were identified by GT^(2) statistics,and the most important factors affecting the microstructural homogeneity were found by special factor analysis.The calculated and experimental results show that the principal parameters influencing the inhomogeneity of solidified microstructure are the primary inlet water pressure and the primary outlet water temperature.According to the consequence of the above investigation,the inhomogeneity of the copper billet microstructure can be effectively improved when the process parameters are controlled and adjusted.

The multi-peak point phenomenon of broadband microwave reflection caused by inhomogeneous plasma

During spacecraft re-entry,the challenge of measuring plasma sheath parameters directly contributes to difficulties in addressing communication blackout.In this work,we have discovered a phenomenon of multiple peaks in reflection data caused by the inhomogeneous plasma.Simulation results show that the multi-peak points fade away as the characteristic frequency is approached,resembling a series of gradually decreasing peaks.The positions and quantities of these points are positively correlated with electron density,yet they show no relation to collision frequency.This phenomenon is of significant reference value for future studies on the spatial distribution of plasmas,particularly for using microwave reflection signals in diagnosing the plasma sheath.

Effective dynamics for a spin-1/2 particle constrained to a curved layer with inhomogeneous thickness

We derive an effective Hamiltonian for a spin-1/2 particle confined within a curved thin layer with non-uniform thickness using the confining potential approach.Our analysis reveals the presence of a pseudo-magnetic field and effective spin–orbit interaction(SOI)arising from the curvature,as well as an effective scalar potential resulting from variations in thickness.Importantly,we demonstrate that the physical effect of additional SOI from thickness fluctuations vanishes in low-dimensional systems,thus guaranteeing the robustness of spin interference measurements to thickness imperfection.Furthermore,we establish the applicability of the effective Hamiltonian in both symmetric and asymmetric confinement scenarios,which is crucial for its utilization in one-side etching systems.

Review of Computational Approaches to Optimization Problems in Inhomogeneous Rods and Plates

In this paper,we review computational approaches to optimization problems of inhomogeneous rods and plates.We consider both the optimization of eigenvalues and the localization of eigenfunctions.These problems are motivated by physical problems including the determination of the extremum of the fundamental vibration frequency and the localization of the vibration displacement.We demonstrate how an iterative rearrangement approach and a gradient descent approach with projection can successfully solve these optimization problems under different boundary conditions with different densities given.

Inhomogeneity of density and mechanical properties of A357 aluminum alloy backward extruded in semi-solid state

The inhomogeneity of density and mechanical properties of A357 aluminum alloy in the semi-solid state were investigated.Numerical simulation and backward extrusion were adopted to study the preparation of cup shells.The results show that the relative density of the wall is the lowest in samples,and that of the base is the highest.With increasing the billet height,more time is needed for relative density of the corner to reach the maximum value,and the relative densities in every region improve evidently with increasing the pressure.The tensile stress was simulated to be the largest at the corner,and the hot tearings were forecasted to mainly appear at the corner too.By employing proper billet height and pressure,the extruded samples consisted of fine and uniform microstructures,and can obtain excellent mechanical properties and Brinell hardness.

A BEEM Study on Effects of Annealing Temperature on Barrier Height Inhomogeneity of CoSi_2/Si Contact Formed in Co-Ti-Si Systems

Ultra thin epitaxial CoSi 2 films are fabricated by solid state reaction of a deposited bilayer of Co(3nm)/Ti (1nm) on n Si(100) substrates at different temperatures.The local barrier heights of the CoSi 2/Si contacts are determined by using the ballistic electron emission microscopy (BEEM) and its spectroscopy (BEES) at low temperature.For CoSi 2/Si contact annealed at 800℃,the spatial distribution of barrier heights,which have mean barrier height of 599meV and a standard deviation of 21meV,obeys the Gaussian Function.However,for a sample that is annealed at 700℃,the barrier heights of it are more inhomogenous.Its local barrier heights range from 152meV to 870meV,which implies the large inhomogeneity of the CoSi 2 film.

Detecting Inhomogeneity in Daily Climate Series Using Wavelet Analysis

A wavelet method was applied to detect inhomogeneities in daily meteorological series, data which are being increasingly applied in studies of climate extremes. The wavelet method has been applied to a few well- established long-term daily temperature series back to the 18th century, which have been ＂homogenized＂ with conventional approaches. Various types of problems remaining in the series were revealed with the wavelet method. Their influences on analyses of change in climate extremes are discussed. The results have importance for understanding issues in conventional climate data processing and for development of improved methods of homogenization in order to improve analysis of climate extremes based on daily data.

Influence of Inhomogeneity on the Estimation of Mean and Extreme Temperature Trends in Beijing and Shanghai

Inhomogeneities in the temperature series from Beijing and Shanghai are analyzed, using the detailed histories of both sets of observations. The major corrections for different periods range from ?0.33 to 0.6°C for Beijing and ?0.33 to 0.3°C for Shanghai, Annual mean and extreme temperature series are deduced from the daily observations and trends in the adjusted and unadjusted series are compared. The adjusted yearly mean temperatures show a warming trend of 0.5°C/ century since the turn of this century and an enhanced one of 2.0°C/ century since the 1960s. In contrast, the unadjusted data show a twice this value trend for Shanghai but little trend for Beijing at the long-term scale and overestimate the recent warming by 50%–130%. Beijing experienced a decrease of frequency of the extremes together with a cooling during the 1940s–1970s and an increase of frequency of extremes together with a warming since then. The trends of frequency of extremes at Shanghai were more or less opposite. It is implied that the regional trends of strong weather variations may be different even when the regional mean temperatures coherently change. Key words Inhomogeneity - Daily temperature series - Climatic warming - Extreme temperature The study was supported by the China NKBRSF Project G 1999043400, IAP/ DF and CAS project (KZ951-A1-402).

Experimental verification of effect of horizontal inhomogeneity of evaporation duct on electromagnetic wave propagation

The evaporation duct which forms above the ocean surface has a significant influence on electromagnetic wave propagation above 2 GHz over the ocean. The effects of horizontal inhomogeneity of evaporation duct on electromagnetic wave propagation are investigated, both in numerical simulation and experimental observation methods, in this paper. Firstly, the features of the horizontal inhomogeneity of the evaporation duct are discussed. Then, two typical inhomogeneous cases are simulated and compared with the homogeneous case. The result shows that path loss is significantly higher than that in the homogeneous case when the evaporation duct height （EDH） at the receiver is lower than that at the transmitter. It is also concluded that the horizontal inhomogeneity of the evaporation duct has a significant influence when the EDH is low or when the electromagnetic wave frequency is lower than 13 GHz. Finally, experimental data collected on a 149-km long propagation path in the South China Sea in 2013 are used to verify the conclusion. The experimental results are consis- tent with the simulation results. The horizontal inhomogeneity of evaporation duct should be considered when modeling electromagnetic wave propagation over the ocean.

ANTI-PLANE SHEAR WAVES SCATTERING FROM A PARTIALLY DEBONDED MAGNETO-ELECTRO-ELASTIC CIRCULAR CYLINDRICAL INHOMOGENEITY

This article presents an analysis of the scattering of anti-plane shear waves from a single cylindrical inhomogeneity partially bonded to an unbounded magneto-electro-elastic matrix. The magneto-electric permeable boundary conditions are adopted. The crack opening displacement is represented by Chebyshev polynomials and a system of equations is derived and solved for the unknown coefficients. Some examples are calculated and the results are illustrated. The results show that the COD increases when the piezomagnetic coefficient of the inhomogeneity bonded to the piezoelectric matrix becomes larger, and that the COD decreases when the piezomagnetic coefficient of the matrix with the piezoelectric inhomogeneity increases.

Interaction between a screw dislocation and an elastic elliptical inhomogeneity with interfacial cracks

The elastic interaction between a screw dislocation and an elliptical inhomogeneity with interfacial cracks is studied. The screw dislocation may be located outside or inside the inhomogeneity. An efficient complex variable method for the complex multiply connected region is developed, and the general solutions to the problem are derived. As illustrative examples, solutions in explicit series form for complex potentials are presented in the case of one or two interfacial cracks. Image forces on the dislocation are calculated by using the Peach-Koehler formula. The influence of crack geometries and material properties on the image forces is evaluated and discussed. It is shown that the interfacial crack has a significant effect on the equilibrium position of the dislocation near an elliptical-arc interface. The main results indicate, when the length of the crack goes up to a critical value, the presence of the interfacial crack can change the interaction mechanism between a screw dislocation and an elliptical inclusion. The present solutions can include a number of previously known results as special cases.

Equilibrium position of misfit dislocation dipole and critical parameters of buried strained nanoscale inhomogeneity in system of viscoelastic matrix

A theoretical model was suggested which describes the generation of the misfit dislocation dipole in the system of the viscoelastic matrix containing a circular stiff nanoscale inhomogeneity.The critical condition of misfit dislocation dipole and the solution of equilibrium position were given.The influence of the ratio of shear modulus,the misfit strain and viscosity on the equilibrium of the dislocation and critical parameter of inhomogeneity was investigated.The result shows that the equilibrium position de increases with the increase of the ratio of original shear modulus and the effect decreases with the increase of viscosity of matrix.Along with the increase of viscosity of matrix,de first increases and then decreases and possesses maximum value when t=0.3τ and tends to a stable value when t≥1.0τ.Along with the increase of viscosity of matrix,Rc first decreases and then increases and possesses minimum value when t=0.3τ and tends to a stable value when t≥1.0τ.

Zone inhomogeneity with the random asymmetric simple exclusion process in a one-lane system

In this paper we use theoretical analysis and extensive simulations to study zone inhomogeneity with the random asymmetric simple exclusion process （ASEP）. In the inhomogeneous zone, the hopping probability is less than 1. Two typical lattice geometries are investigated here. In case A, the lattice includes two equal segments. The hopping probability in the left segment is equal to 1, and in the right segment it is equal to p, which is less than 1. In case B, there are three equal segments in the system; the hopping probabilities in the left and right segments are equal to 1, and in the middle segment it is equal to p, which is less than 1. Through theoretical analysis, we can discover the effect on these systems when p is changed.

Effects of Aerosol Vertical Inhomogeneity on the Upwelling Radiance and Satellite Remote Sensing of Surface Reflectance

There are two widely used radiative models without consideration of aerosol inhomogeneity for satellite remote sensing application, the Homogeneous Model and the Two-layer Model with aerosol in the lower layer. In this paper, effects of the aerosol vertical inhomogeneity on upwelling radiance and satellite remote sensing of surface reflectance are analyzed through numerical simulations by using two models. As shown in the simulations by using 24 representative aerosol models, there is often a considerably large error in upwel-ling radiance calculated by two models (Homogeneous and Two-layer) for the short wavelength channel with strong molecular scattering, owing to the difference between molecular and aerosol scattering proper-ties. For the long wavelength channel, the error is small if aerosol optical parameters are less variable with height, but it could also be significant if there are aerosol layers with different scattering phase functions and single scattering albedo. The radiance errors by the Homogeneous Model and the Two-layer Model can be up to 31.4% and 31.5% for the clean atmosphere, and in case of turbid atmosphere 67.8% and 59.2%, respectively. The radiance error could result in a large uncertainty of surface reflectance retrievals, especially for the short wavelength channel and the strongly absorbing aerosol. For the turbid atmosphere with strong-ly absorbing aerosol, the Homogeneous Model and the Two-layer Model are not suitable for atmospheric correction application. Key words Satellite remote sensing - Aerosol inhomogeneity - Surface reflectance - Radiance

Annealing temperature influence on the degree of inhomogeneity of the Schottky barrier in Ti/4H–SiC contacts

Tung＇s model was used to analyze anomalies observed in Ti/Si C Schottky contacts. The degree of the inhomogeneous Schottky barrier after annealing at different temperatures is characterized by the ‘T0anomaly＇ and the difference（△Φ）between the uniformly high barrier height（Φ0B） and the effective barrier height（Φeff B）. Those two parameters of Ti Schottky contacts on 4H–Si C were deduced from I–V measurements in the temperature range of 298 K–503 K. The increase in Schottky barrier（SB） height（ΦB） and decrease in the ideality factor（n） with an increase measurement temperature indicate the presence of an inhomogeneous SB. The degree of inhomogeneity of the Schottky barrier depends on the annealing temperature, and it is at its lowest for 500-°C thermal treatment. The degree of inhomogeneity of the SB could reveal effects of thermal treatments on Schottky contacts in other aspects.

Thermohaline structure inhomogeneity associated with polynia at the northern margin of Emery Ice-shelf

Based on the hydrographic data in austral summer during the 22nd Antarctic Expedition of China(2005/2006),some features can be found about the northern margin of Emery ice shelf as follows.The heat content in the surface layer(0-50 m) at the eastern end and the western end of the ice-shelf margin is much higher than that at the middle.The upper mixing-layer depth and the seasonal thermocline depth at the middle of the ice-shelf northern margin are much shallower than those at the both ends.However there is much less difference between the middle and the ends in the bottom layer.The remote sensing photos show that the inhomogeneity in the surface-layer water is closely related to the spatial distribution of the floes and polynia in the area.

Local inhomogeneity of mechanical properties in stir zone of friction stir welded AA1050 aluminum alloy

The local inhomogeneity of the stir zone in friction stir welded face-centered cubic metal was investigated,which has multiple activated slip systems during plastic deformation,by selecting commercial AA1050 aluminum alloy as an ideal experimental material.The local inhomogeneity was evaluated by uniaxial tensile tests using small samples with a 1 mm gauge length.The corresponding microstructural parameters such as grain size,misorientation angle distribution,and micro-texture,were quantified by the backscattered electron diffraction technique.A comprehensive model was used to reveal the microstructure−mechanical property relationship.The experimental results showed that the uniaxial tensile property changes significantly across the weld.The maximum ultimate tensile strength(UTS)occurred in the center of the stir zone,which was 99.0 MPa.The weakest regions were located at the two sides of the stir zone.The largest difference value in UTS reached 14.9 MPa,accounting for 15%of the maximum UTS.The analysis on the structure−mechanical property relationship suggests that the micro-texture change with the location formed during the rotational material flow is the main reason for the local inhomogeneity.

Deformation inhomogeneity due to sample-anvil friction in cylindrical compression test

Finite element(FEM)analysis was used to systematically evaluate the inhomogeneity of deformation in cylindrical samples with various sample-anvil friction coefficients,m.It was found that the level of friction strongly influences the deformation homogeneity,which increases significantly with the friction coefficient although the overall geometry of the samples almost remains the same when m >0.4.The position,at which the effective strain along the maximum radial direction in a compressed sample is equal to the equivalent strain of the sample,does not vary greatly with respect to both equivalent strain of the sample and m.Hardness measurements of compressed cylindrical 5056B Al alloy samples revealed a change of effective strain distribution similar to that revealed by FEM analysis.There exists a quantitative relationship between the hardness and the effective strain if no recrystallization or recovery occurs during the compression process.