Method Development and Validation of the Simultaneous Analysis of Methylisothiazolinone, Methylchloroisothiazolinone, Benzisothiazolinone and Bronopol in Washing-Up Liquid

A method of analysis for the simultaneous determination of methylisothiazolinone (MI), methylchloroisothiazolinone (CMI), benzisothiazolinone (BIT) and Bronopol (BNP) in washing-up liquid was established. The method consisted of a gradient HPLC analysis at three different wavelengths. The four compounds could be analyzed with good precision and accuracy.

Orientational Separation of Sulfur in Petroleum Coke by Alkali Calcining and Reflux Washing

The application of high-sulfur petroleum coke after desulfurization in aluminum electrolysis anodes is an important development trend. However, removing sulfur from high-sulfur petroleum coke is still a significant challenge.This study proposes alkali calcining and reflux washing to examine the impacts of temperature, particle size, the mass ratio of Na_(2)CO_(3) to NaOH, and total sodium addition on the desulfurization efficiency and mechanism. The results show that the desulfurization rate increases with increasing temperature, increasing total sodium content, and decreasing particle size. The addition of alkali can significantly reduce the opening-ring reaction temperature of thiophene and convert organic sulfur into inorganic sulfur(Na_(2)S). Three washing methods were compared, and reflux washing was selected to separate inorganic sulfur(Na_(2)S) from calcined petroleum coke. The sulfur content in petroleum coke decreased from 7.29% to 1.90%, with a desulfurization rate of 80.13% under optimal conditions. The petroleum coke was analyzed before and after desulfurization using X-Ray diffraction(XRD), Scanning Electron Microscopy(SEM), Infrared Spectroscopy(IR), Thermogravimetric Analysis and Differential Scanning Calorimetry(TG-DSC), Gaschromatography-mass Spectrometry(GC-MS). The results show that thiophene and benzothiophene in petroleum coke are decomposed and converted into octane and ethyl cyclohexane. These new observations are expected to provide further understanding and guidance for the utilization of highsulfur petroleum coke.

Discussion on the Treatment of Palmoplantar Keratosis by TCM Soaking and Washing

By combing the mechanism and advantages of traditional Chinese medicine(TCM)soaking and washing and combining TCM syndrome differentiation with western medicine differentiation of diseases,guided by the view that"the principle of external treatment is that of internal treatment",this article discusses the differentiation and treatment ideas of palmoplantar keratosis by TCM soaking and washing,which will provide a reference for clinical treatment.

Effect of Water Washing Pre-treatment on the Properties of Glass-ceramics from Incinerator Fly Ash Using Electronic Arc Furnace

Production of glass-ceramics by sintering the molten slag obtained from electric arc furnace treatment of fly ash was investigated. The effect of washing pretreatment prior to melting the fly ash on the microstructure and properties of the glass-ceramics was examined. The results show that washing pretreatment of fly ash can decrease alkali metal chloride and increase network former in fly ash, which results in the increase of peak crystallization temperature of parent glass and strengthening of properties of bending strength and chemical stability of the glass-ceramics. The optimal heat treatment temperature for parent glass of washed fly ash is 1 173 K, at which the crystalline phase of glass-ceramics is composed of gelignite （Ca2A12SiO7） and akermanite （Ca2MgSi207）. Glass-ceramics produced at optimal heat treatment temperature are excellent in term of the physical and chemical properties and leaching characteristics, indicating attractive potential as substitute of nature materials.

Bronchial Washing to Diagnose Smear-Negative Pulmonary Tuberculosis

Introduction: Bronchoscopy with bronchial washing is useful for the diagnosis of pulmonary tuberculosis (TB) when sputum smears are negative. However, its indication has not been standardized. Therefore, we conducted a retrospective study to assess the diagnostic value of bronchial washing in patients suspected with pulmonary TB. Methodology: A retrospective analysis was performed on patients diagnosed with pulmonary TB in Kosin university gospel hospital, a tertiary hospital with 969 beds in South Korea, from March 2017 to December 2018. We obtained three serial sputum samples for acid-fast bacilli (AFB) smear and culture, and all patients underwent bronchoscopy with bronchial washing for AFB smear and culture. Results: Fifty-six patients were enrolled in the study. Smear-negative pulmonary TB (SNPT) was diagnosed in 42/56 (75%) patients. Among the patients with smear-positive sputum, 14/14 (100%) showed culture-positive sputum, while smear- and culture-positive bronchial washing were seen in 7/14 (50%) and 12/14 (85.7%) patients, respectively. Among the patients with SNPT, 17/42 (40.47%) had culture-negative sputum and were diagnosed using the bronchoscopic washing. Conclusions: For patients with smear-negative sputum, it is necessary to perform bronchoscopic washing to increase the diagnostic rate of pulmonary TB. To control the transmission of pulmonary TB, it is necessary to use a fast and accurate examination method.

Washing and Dyeing Wastewater Treatment by Combined Nano Flocculation and Photocatalysis Processes

The research investigated the performance of combined process (flocculation pretreatment-pho- to catalysis). The characteristics of nano flocculation and photocataly were evaluated by simulated dye and surfactant wastewater. In the coagulation and settling period, decolorization rate of five dyes wastewater by nano flocculant was higher than 95%. In the photocatalytic period, degradation of twelve sodium dodecyl benzene sulfonate reached 33%. Washing and dyeing wastewater treated by combined process conformed to the “textile dyeing and finishing industry back to the water quality standard” (FZ/T 01107-2011). The results showed that the combined process was highly advanced treatment for washing and dying wastewater.

Application of Electrocoagulation and Electrolysis on the Precipitation of Heavy Metals and Particulate Solids in Washwater from the Soil Washing

Soil washing, ex situ mechanical technique, is one of the few permanent treatment alternatives to remove metal contaminants from soils by employing physical separation based on mineral processing technologies to remove discrete particles or metal-bearing particles and/or chemical extraction based on leaching or dissolving process to extract the metals from the soils into an aqueous solution. However, washwater remained from soil washing process contains discrete particulate particles along with heavy metals as solution phase to be treated separately, as well as this process can produce large amount of sludge that requires further treatment, slow metal precipitation, poor settling, the aggregation of metal precipitates. Electrical treatments including electrocoagulation and electrolysis can be effective in removing these substances from washwater. This paper reviews the theoretical models in applying electrocoagulation and electrolysis to remove heavy metals and discrete particulate particles in washwater by examining and comparing the status of washwater treatment technologies which have been undertaken, mostly in the US and EU for the period 1990-2012.

Surfactant-Enhanced Washing of Soils Contaminated with Wasted-Automotive Oils and the Quality of the Produced Wastewater

An old automotive industrial site located at Mexico City with many years of operation and contaminated with heavy oil hydrocarbons, particularly spent oils, was assessed for restoration using the surfactant enhanced soil washing (SESW) process. The main goal of this study was to characterize the contaminated soil in terms of TPHs, BTEX, PAHs, and metals contents as well as microbiologically (total heterotrophs and specific degrading microorganisms). We also aimed to determine the surfactant type and concentration to be used in the SESW process for the automotive waste oil contaminated soil. At the end, sixteen kg of contaminated soil were washed and the produced wastewater (approximately 40 L) was characterized in terms of COD, BOD;solids, and other physico-chemical parameters. The soil contained about 14,000 mg of TPH/kg soil (heavy fraction), 0.13 mg/kg of benzo (k) fluoranthene and 0.07 mg/kg of benzo (a) pyrene as well as traces of some metals. Metals concentrations were always under the maximum concentration levels suggested by Mexican regulations. 15 different surfactants were used to identify the one with the capability to achieve the highest TPH removal. Surfactants included 5 anionics, 2 zwitterionic, 5 nonionics and 3 natural gums. Sulfopon 30 at a concentration of 0.5% offered the best surfactant performance. The TPH removals employing the different surfactants were in the range from 38% to 68%, in comparison to the soil washing with water (10% of TPH removal). Once the surfactant was selected, 70 kg of soil were washed and the resulting water contained approximately 1300 mg/L of COD, 385 mg/L of BOD (BOD/COD = 0.29), 122 mg/L of MBAS, and 212 mg/L of oil and greases, among other contaminants.

Investigation of Different Washing Effects on Physical and Mechanical Properties of Cotton Knitted Garments

This paper deals with three types of washing (enzyme, softener, Silicone) effects on 100% cotton Single Jersey T-shirt, Slub Single Jersey T-shirt, Double Lacoste (5% Lycra) Polo shirt, Single jersey CVC (T-shirt) and PC single Jersey (T-shirt). Typical industrial washing procedures and techniques were followed and then physico-mechanical properties were analyzed under standard condition. It is observed that after washing, weight of each garments has increased from 5% to 36%;stitch length of the constituted fabric has decreased from 1% to 10% approximately;CPI has increased 23% for CVC fabric only for enzyme treatment and for other process it has a little bit or no wash effects. Same effects found for WPI except 100% cotton and Double Lacoste. Shrinkage property both for lengthwise and widthwise remains the same except CVC and Double Lacoste knitted garments and spirality has almost unchanged except 100% cotton and slub fabric. Both the dry and wet rubbing properties have improved after any types of wash except 100% cotton on Silicone wash. Water absorbency property has increased;pH of all the samples is under controlled and lies between 4.5 and 5.0. But there is no significant change of colorfastness to wash and stain after these washing treatments.

Isolation of Iron Bacteria from Washing Sludge Filters Kolda (Senegal) Water Treatment Station and Study of the Kinetics of Biological Degradation of the Iron (II)

In the present work, the treatment of synthetic waters doped with iron (II) has been studied. The treatment mechanism used in this study is the biological oxidation which consists, in test tubes, of bringing bacteria isolated on Petri dishes into contact with water containing divalent iron (II). These de-ironing bacteria (non-specific bacteria) are used to carry out laboratory biological oxidation experiments on iron (II) under different pH conditions (pH = 3.4 - 3.6, pH = 7.3 - 7.5 and pH = 9.8 - 10) and variable concentration of iron (II). Biological treatment trials included different concentrations of iron during time intervals of a day. Examination of the elimination kinetics of Iron (II) indicates a removal rate of 59.453% for an initial iron concentration in the synthetic solution of 1 mg·L−1 at basic pH (pH = 9.8 - 10). Therefore, the degradation of divalent iron by this method seems to be quite effective, but it should be noted that biological nitrification is impaired by the presence of high iron concentrations above 5 mg·L−1.

Quantitative assessment and significance of gas washing of oil in Block 9 of the Tahe Oilfield,Tarim Basin,NW China

Some Ordovician and Triassic oils in Block 9 are characterized by light oils,which have distinctly differentiated from heavy oils in other blocks in the Tahe Oilfield,Tarim Basin.Based on the whole oil gas chroma- tograms,this paper estimates the effect of oil migration and fractionation and the amount of depletion(Q)in terms of the n-alkanes depletion model.The results showed that the amount of depletion in the Ordovician reservoir is highest in the east of this block,e.g.the depletion is 97% in Well T904.The amount of Q gets lower to the west,e.g.the depletion is 53.4%in Well T115 and there is no sign of depletion in Well S69.It is suggested that the direction of gas washing is from the east to the west.The compositions and isotopic characteristics of associated gas in Ordovician oils indicated that the gas might be derived from Cambrian source rocks of the Caohu Depression which lies to the east of Block 9.In contrast,no obvious depletion of n-alkanes in Triassic oils was found,suggesting that the migration pathway of natural gas has been limited to the Ordovician karst fracture system formed in the Early Hercynian Orogeny.Different depletions of the Ordovician and Triassic oils can reveal fault activities in this region.

Efficient Extraction of Astaxanthin from Phaffia rhodozyma with Polar and Non-polar Solvents after Acid Washing

在酸的洗以后与各种各样的溶剂从 Phaffia rhodozyma 提取 astaxanthin 的方法被调查。抽取效率清楚地在 P 的酸的洗以后被增加。rhodozyma 房间。当 HCl 的集中是 0.4 摩尔时 ?

高white washing防御力的P2P全局信任模型

在分析P2P网络的特点及其所面临的各种安全问题的基础上,提出了一个全局信任模型,对恶意行为及free riding都有较高的抵御力.特别是当恶意节点或信誉值很低的自私节点企图重新注册时(white washing),模型采用双重机制,可以很快将之屏蔽在外.仿真结果证明,模型有较强的恶意节点免疫力,尤其对于white washing有高的防御能力.

APPLICATIONS OF FLOCCULANT IN BLEACHING AND WASHING OF KAOLIN

The difficulties of washing during the dressing of kaolin ore have been analyzed, the multistep intermittent washing model has been deduced, and effective methods for dealing with the difficulties were put forward. Experimental results show that the bleaching and washing process was enhanced, the washing time was shortened and the consumption of water was reduced by means of adding flocculant.

Recycling of waste foundry sands by chemical washing method

This study aims to remove the metals(inorganic and heavy metals) in waste foundry sand(WFS)via chemical washing method. Washed waste foundry sand(WWFS) samples were obtained by using triptych washing successively with 5 M HCl, 5 M H_2SO_4 and 5 M NaOH solutions. Analysis on functional groups,micropores, heavy metals,and inorganic components of WFS and WWFS was carried out by using FT-IR, SEM and XRF. Results show that the concentration values of some inorganic components such as Ca, Fe, Mg, S were decreased, and the maximum removal percentage of these inorganic components are 47%, 19%, 32%, and 8%,respectively. The concentration values for each of the heavy metals of WWFS are below of limit values given in App-3 List of Regulation on General Principles of Waste Management. The removal percentages of Pb, As and Zn elements are 100%, 71%, and 40%, respectively. The findings of this research suggest that WWFS can be used in more applications due to its ability to remove heavy metals and some other inorganic components.

Washing Defects and Remedial Actions of Denim Garments and Statistical Review of Denim Sectors in Emerging Economy

This paper aimed to identify the washing defects of denim garments and the remedies for these washing defects of denim garments in Bangladesh.The other purpose of this paper is to explain how such errors are related to the waste,production,and production costs of denim clothing.It also provides a statistical review of the denim sector in Bangladesh as compared to other countries.This paper is conveyed based on theoretical and statistical.It appears washing defects of denim garment,and their remedial actions and reveals the effect of washing defects on wastage,production,and production cost of denim garments.This research paper shows more washing defects of denim garments in Bangladesh.The statistical review displays that Bangladesh is exporting denim products nearly 200 million pieces every year over the world and ranks as the second-largest denim garments exporter after China.By studying this paper,the manufacturer of denim garments in Bangladesh and other countries will be conscious of these defects and able to minimize these defects that will help improve the economy all over the world.

Synthesis of Super Plasticizer NF-30 from Coal Coking by Product Washing Oil and Performance Analysis

Super plasticizer was synthesized by using coal coking by product washing oil and industrial naphthalene. The results show that sulfonationt time （2.5 h）, sulfonation temperature （160 ℃） and condensation time （5.0 h） are key factors. Adding oxidizing agent MO in the course of synthesis can decrease the emission of SO2 in exhaust （20%）. Compared with NF, NF-30 have some advantages in lower cost, high water reducing rate （19.7%） and optimum early strengths. Moreover, TGA-DTA and SEM analysis were adopted to research the NF-30 modified concrete on hydyation mechanism. The analysis show that, compared with NF, there are a large number of hydration products such as Ca （OH）2, C-S-H, AFt etc of NF-30, the structure of NF-30 is dense and the performance is good.

Bending and Washing Reliabilities of Screen-Printed UHF RFID Tags Based on Woven Water-Mark Fabric

Compared with bar code and quick response( QR) code in the storage and retailing management of textiles, the ultra-high frequency( UHF) radio frequency identification( RFID) tags have high information capacity as well as reliability in complex environmental conditions. In this study,the UHF RFID tags with perfect integration with textiles are assembled with screen-printed antenna on woven water-mark nylon fabric and Alien UHF integrated circuit( IC), and their reading performance under various washing and bending conditions is evaluated by an RFID reader. The results show that the tags after fifty bending( both arch and sink) cycles of screen-printed antenna still have reading distance more than 5.5 m,and an average reading distance is over 4.0 m after five washing cycles. The experimental results demonstrate that the tag antenna on the water-mark fabric can be manufactured by the screen-printing technology,and a coating process on this fabric facilitates the reading performance and the resistance against complex mechanical impact.