Lattice structure adaptive IIR notch filter based on least square kurtosis

A new variable step-size algorithm for a second-order lattice form structure adaptive infinite impulse response （IIR） notch filter to detection and estimation frequency of sinusoids in Gaussian noises is proposed. Utilizing least square kurtosis of output signals as a cost function, the new gradient-based algorithm to update frequency of the adaptive IIR notch filter and the new variable step-size algorithm are given. The computer simulation results show that the proposed algorithm has better ability in suppressing colored Gaussian noises and better accuracy in estimating parameters at low SNR than previous algorithms.

A novel algorithm of adaptive IIR lattice notch filter and performance analysis

A novel adaptive algorithm of IIR lattice notch filter realized by all-pass filter is presented. The time-averaged estimation of cross correlation of the present instantaneous input signal and the past output signal is used to update the step-size, leading to a considerably improved convergence rate in a low SNR situation and reduced steady-state bias and MSE. The theoretical expression for steady-state bounds on the step-size is derived, and the influence factors on the stable performance of the algorithm theoretically are analyzed. A normalized power factor is then introduced to control variation of step-size in its steady-state bounds. This technique prevents divergence due to the influence of large power input signal and improves robustness. Numerical experiments are performed to demonstrate superiority of the proposed method.

Notch filter feedback controlled chaos in buck converter

A method of controlling chaos in the voltage-mode buck converter is presented by using an improved notch filter feedback control in this paper. The proposed control part comprises a notch filter and a low-pass filter. The discrepancy between the outputs of the two filters is introduced into the control prototype of the power converter. In this way, the system period-1 solution is kept unchanged. The harmonic balance method is applied to analysing the variation law of the system bifurcation point, and then the stable range of the feedback gain is ascertained. The results of simulation and experiment are also given finally.

Multi-Frequency Interference Detection and Mitigation Using Multiple Adaptive IIR Notch Filter with Lattice Structure

Radio Frequency Interferences (RFI), such as strong Continuous Wave Interferences (CWI), can influence the Quality of Service (QoS) of communications, increasing the Bit Error Rate (BER) and decreasing the Signal-to-Noise Ratio (SNR) in any wireless transmission, including in a Digital Video Broadcasting (DVB-S2) receiver. Therefore, this paper presents an algorithm for detecting and mitigating a Multi-tone Continuous Wave Interference (MCWI) using a Multiple Adaptive Notch Filter (MANF), based on the lattice form structure. The Adaptive Notch Filter (ANF) is constructed using the second-order IIR NF. The approach consists in developing a robust low-complexity algorithm for removing unknown MCWI. The MANF model is a multistage model, with each stage consisting of two ANFs: the adaptive IIR notch filter Hl(z) and the adaptive IIR notch filter HN(z), which can detect and mitigate CWI. In this model, the ANF is used for estimating the Jamming-to-Signal Ratio (JSR) and the frequency of the interference (w(0)) by using an LMS-based algorithm. The depth of the notch is then adjusted based on the estimation of the JSR. In contrast, the ANF HN(z) is used to mitigate the CW interference. Simulation results show that the proposed ANF is an effective method for eliminating/reducing the effects of MCWI, and yields better system performance than full suppression (kN=1) for low JSR values, and mostly the same performance for high JSR values. Moreover, the proposed can detect low and high JSR and track hopping frequency interference and provides better Bit error ratio (BER) performance compared to the case without an IIR notch filter.

Theoretical and experimental study of Chen chaotic system with notch filter feedback control

Since the past two decades, the time delay feedback control method has attracted more and more attention in chaos control studies because of its simplicity and efficiency compared with other chaos control schemes. Recently, it has been proposed to suppress low-dimensional chaos with the notch filter feedback control method, which can be implemented in a laser system. In this work, we have analytically determined the controllable conditions for notch filter feedback controlling of Chen chaotic system in terms of the Hopf bifurcation theory. The conditions for notch filter feedback controlled Chen chaoitc system having a stable limit cycle solution are given. Meanwhile, we also analysed the Hopf bifurcation direction, which is very important for parameter settings in notch filter feedback control applications. Finally, we apply the notch filter feedback control methods to the electronic circuit experiments and numerical simulations based on the theoretical analysis. The controlling results of notch filter feedback control method well prove the feasibility and reliability of the theoretical analysis.

TIME-VARYING AR MODELING AND ADAPTIVE IIR NOTCH FILTER FOR ANTI-JAMMING DSSS RECEIVER

Using Time-Varying AR (TVAR) model and adaptive notch filter is a new method for the non-stationary jammer suppression in Direct Sequence Spread Spectrum (DSSS). The performance of TVAR model for Instantaneous Frequency (IF) estimation will be affected by some factors such as basis functions. Focusing on this problem, the optimal basis function of TVAR model for the IF estimation of the LFM signal is obtained in this paper. Besides the depth and width of notching, the phase properties of notch filter affect the Signal-to-Interference plus-Noise Ratio (SINR) of correlation output to the narrowband jammer suppression in DSSS, in response to the problem the closed solution of correlation output SINR improvement has been derived when a single frequency jammer passes through direct IIR notch filter, and its performance has been compared with those of five coefficient FIR filters. Later, a novel method for LFM jammer suppression based on Fourier basis TVAR model and direct IIR notch filter is proposed. The simulation results show the effectiveness of the proposed method.

The Effect of Notch Filter on RFI Suppression

Radio Frequency Interference (RFI) suppression is an important technique in the ultra-wideband synthetic aperture radar (UWB SAR). In this paper, we mainly analyze the performance of a notch filter for RFI sup-pression. The theoretical output from notch filter is presented based on RFI signal’s narrowband property. The research conclusion shows that the notch filter has significant effect on sidelobes of the system response, which might be considered to be false targets, however it has little effect on the resolution of the system re-sponse. The theoretical result is verified by simulation and experimental data processing both in one dimen-sion (range dimension) and in two dimensions (range and azimuth dimension).

Performance Analysis of an Inverse Notch Filter and Its Application to <i>F₀</i>Estimation

In this paper, we analyze an inverse notch filter and present its application to F0 (fundamental frequency) estimation. The inverse notch filter is a narrow band pass filter and it has an infinite impulse response. We derive the explicit forms for the impulse response and the sum of squared impulse response. Based on the analysis result, we derive a normalized inverse notch filter whose pass band area is identical to unit. As an application of the normalized inverse notch filter, we propose an F0 estimation method for a musical sound. The F0 estimation method is achieved by connecting the normalized inverse notch filters in parallel. Estimation results show that the proposed F0 estimation method effectively detects F0s for piano sounds in a mid-range.

BER of OFDM System with Multiple NBI Rejection Cascade Complex Coefficient Adaptive IIR Notch Filter

In this paper, rejection of multiple narrowband interferers in a binary phase shift keying modulated orthogonal frequency division multiplexing (BPSK-OFDM) system is investigated. The BPSK-OFDM system in consideration operates in an additive white Gaussian noise (AWGN) channel. A cascade complex coefficient adaptive infinite impulse response (IIR) notch filter with gradient-based algorithm is used to reject the interferers. Bit error ratio (BER) performance of the system is studied and a general closed-form expression is derived assuming negligible steady-state leakage NBI and by estimating the decision variable as Gaussian distributed based on Central Limit Theorem (CLT). Dependence of the BER performance on the notch bandwidth coefficient is demonstrated by the analysis. Extensive simulation results are included to substantiate accuracy of the analysis.

Design of Low Power CMOS LNA with Current-Reused and Notch Filter Topology for DS-UWB Application

This paper presents the design of a low power LNA with second stage that uses a notch filter for DS-UWB application. The LNA employs a current reuse structure to reduce the power consumption and an active second order notch filter to produce band rejection in the 5 - 6 GHz frequency band. The input reflection coefficient S11 and output reflection S22 are both less than –10 dB. The maximum power gain S21 is 15 dB while the maximum rejection ratio is over –10 dB at 4.8 GHz. The minimum noise figure is 5 dB. The input referred third-order intercept point (IIP3) is –7 dBm at 6 GHz. The power consumption is 6.4 mW from a 1-V power supply.

Efficient background removal based on two-dimensional notch filtering for polarization interference imaging spectrometers

A background removal method based on two-dimensional notch filtering in the frequency domain for polarization interference imaging spectrometers（PIISs） is implemented. According to the relationship between the spatial domain and the frequency domain, the notch filter is designed with several parameters of PIISs, and the interferogram without a background is obtained. Both the simulated and the experimental results demonstrate that the background removal method is feasible and robust with a high processing speed. In addition, this method can reduce the noise level of the reconstructed spectrum, and it is insusceptible to a complicated background, compared with the polynomial fitting and empirical mode decomposition（EMD） methods.

The Notched Filtering Characteristics of Stratified Volume Holographic Grating

Utilizing the tool of beam propagation method (BPM) to calculate the zeroth order diffraction beam intensity, we find SVHG displays notched diffraction response as a function of the readout wavelength. Using the method of SA and considering the variance of refractive index as the readout wavelength changes, a practiced notch filter can be designed and the period of the filter is discussed.

Microwave photonic notch filter with complex coefficient based on four wave mixing

A microwave photonic notch filter with a complex coefficient is proposed and demonstrated based on four wave mixing(FWM). FWM effect of two single-frequency laser beams occurs in a highly nonlinear fiber(HNLF), and multi-wavelength optical signals are generated and used to generate the multi-tap of microwave photonic filter(MPF). The complex coefficient is generated by using a Fourier-domain optical processor(FD-OP) to control the amplitude and phase of the optical carrier and phase modulation sidebands. The results show that this filter can be changed from bandpass filter to notch filter by controlling the FD-OP. The center frequency of the notch filter can be continuously tuned from 5.853 GHz to 29.311 GHz with free spectral range(FSR) of 11.729 GHz. The shape of the frequency response keeps unchanged when the phase is tuned.

Double Narrow Notch Spectral Filter Design Using Waveguide Grating on Metal Substrate

A double narrow notch spectral filter design using planar dielectric grating diffraction coupled resonant thin dielectric waveguide on metal substrate is numerically studied in this article. Due to excitation and coupling of guided resonance mode in thin dielectric waveguide layer and surface plasmon mode on the interface between the waveguide and the metal substrate, double deep and narrow reflection spectrum dip can be obtained. This physical explanation is confirmed by the momentum matching conditions of resonance and the field distribution calculation. As an example, double notch filter design with full width half maximum less than 2 nm centered at 549 nm and 651 nm is presented.

Research of the terahertz dual-band notch filter based on FSS structures

In this paper,a dual-band notch filter for two-layer frequency selective surface(FSS)at terahertz(THz)frequency with high filtering performance has been realized on high-resistivity silicon substrates.With periodic metallic resonators patterned on the silicon wafer,the designed filter can provide two tunable resonant frequencies for terahertz application.The transmission response was improved by introducing an extra surrounding pattern around the T-shaped structure,and the location of transmission drop was tuned independently with geometric parameters.Simulated by finite-integral time-domain method,the filter is designed to operate between 0.2 and 0.6 THz with dual-band band-stop performance,a salient feature of this design is making the low sensitivity of its frequency response to the incident angles,which allows to place the filter close to the radiation source with spherical wave fronts.The proposed structures were fabricated using photolithography and tested by THz time-domain spectroscopy system.Experimental results show that the transmission response has more than 12 and 32 dB rejections near 285 and 460 GHz respectively,which is in good agreement with the simulation result.

Development of Hexagonal MMR Based UWB Bandpass Filter with 5 GHz Notch Band

This paper presents an experimental verification of ultra-wideband bandpass filter (BPF) for UWB applications and notch filter in order to suppress 5 GHz narrowband service when it coexists with UWB radio system. The BPF consists of a hexagonal shaped multiple mode resonator (MMR) with interdigital coupling at both sides. Notch filter is derived from BPF by introducing four embedded open stubs near by the MMR. The developed BPF has insertion loss of –2 dB and the minimum return loss about –35 dB, while for the notch filter they are –3 dB and –40 dB respectively. The group delay obtained for bandpass filter is below 0.2 ns and for notch filter, it is about 0.3 ns. With the above structural features the overall dimensions of the filter is 38 mm (length) × 3.2 mm (breadth) × 1.6 mm (height) and the percentage fractional bandwidth (FBW) of the proposed filter is about 120.48%.

Miniaturized Planar Ultra-Wideband Bandpass Filter with Notched Band

This paper presents a planar ultra-wideband (UWB) bandpass filter with sharp out-of-band rejection performance. The filter is formed by a folded multiple-mode resonator to realize high performance in an operation band from 3.3 to 10 GHz with a very compact size of 20 mm × 20 mm × 0.5 mm. An extra notched band centered at 5.8 GHz is further accomplished by etching a Hilbert fractal curve slit on the filter without the necessity of readjusting the geometrical parameters. The simulated and measured results are in good agreement.

DUAL MODE WIDEBAND BAND-PASS FILTER WITH NOTCHED BAND FOR COMMUNICATION SYSTEM

This paper presents a planar microstrip wideband dual mode Band-Pass Filter(BPF) from 2 GHz to 3.4 GHz with a notched band at 2.62 GHz.The dual mode band-pass filter consists of a ring resonator with two quarter-wavelength open-circuited stubs at =90o and =0o,respectively.A square perturbation stub has been put at the corner of the ring resonator to increase the narrow stopbands and improve the performance of selectivity.By using a parallel-coupled feed line,a narrow notched band is introduced at the required frequency and its Fractional BandWidth(FBW) is about 5%.The proposed filter has a narrow notched band and a wide pass-band with a sharp cutoff frequency characteristic,the attenuation rate for the sharp cutoff frequency responses is 297.17 dB/GHz(cal-culated from 1.959 GHz with-34.43 dB to 2.065 GHz with-2.93 dB) and 228.10 dB/GHz(calculated from 3.395 GHz with-2.873 dB to 3.507 GHz with-28.42 dB).This filter has the advantages of good insertion loss in both operating bands and two rejections of greater than 16 dB in the range of 1.59 GHz to 1.99 GHz and 3.49 GHz to 3.98 GHz.Having been presented in this article,the measurement results agree well with the simulation results,which validates our idea.

基于改进自适应陷波的双馈风电场时变次同步振荡抑制策略

双馈风电场经串补电容并网时,可能引发次同步控制相互作用(subsynchronous control interaction,SSCI),严重威胁系统安全稳定运行。通过在风机控制器中引入陷波器可有效阻断SSCI,然而固定参数陷波器难以适应实际系统中次同步振荡表现出的频率大范围时变特征。为解决这一问题,该文提出一种基于改进自适应陷波(adaptive notch filter,ANF)的双馈风电场时变次同步振荡抑制策略。首先,分析ANF安装于风机转子侧变流器(rotor-side converter,RSC)不同位置时对次同步振荡分量的阻断效果,确定ANF的最佳安装位置;其次,基于紧缩技术近似投影子空间跟踪算法(projection approximation subspace tracking based on the deflation technique,PASTd)在线获取次同步振荡信息,提出总体控制架构,设计基于量测数据辨识的ANF中心频率更新策略;最终,在考虑风速、风机台数、无功出力、电网拓扑变化等多种影响因素的情况下,验证控制策略对频率时变次同步振荡的抑制效果。与现有方法相比,所提控制策略不依赖于系统的准确数学模型,且具备较强的鲁棒性和适应性。