Gravel hardness effect on compaction characteristics of gravelly soil

The compaction characteristics of gravelly soil are affected by gravel hardness.To investigate the evolution and influencing mechanism of different gravel hardness on the compaction characteristics of gravelly soil,heavy compaction tests and crushing tests were conducted on gravelly soils with gravels originated from hard,soft and extremely soft rocks.According to orthogonal experiments and variance analysis,it was found that hardness has a significant impact on the maximum dry density of gravelly soil,followed by gravel content,and lastly,moisture content.For gravel compositions with an average saturated uniaxial compressive strength less than 60 MPa,the order of compacted maximum dry density is soft gravels>hard gravels>extremely soft gravels.Each type of gravelly soil has a threshold for gravel content,with 60%for hard and soft gravels and 50%for extremely soft gravels.Beyond these thresholds,the compacted dry density decreases significantly.There is a certain interaction between hardness,gravel content,and moisture content.Higher hardness increases the influence of gravel content,whereas lower hardness increases the influence of moisture content.Gravelly soils with the coarse aggregate(CA)between 0.7 and 0.8 typically achieve higher dry densities after compaction.In addition,the prediction equations for the particle breakage rate and CA ratio in the Bailey method were proposed to estimate the compaction performance of gravelly soil preliminarily.The results further revealed the compaction mechanism of different gravelly soils and can provide reference for subgrade filling construction.

Influence of heat input on microhardness and microstructure across the welding interface between stainless steel and low alloy steel

The welding interface is crucial to the service safety of dissimilar metal weld(DMW)joints between stainless steel(SS)and low alloy(LA)steel.Different status of welding interfaces was prepared by cladding SS consumables to LA steel substrates with different heat inputs via tungsten inert gas arc welding(TIG),followed by a series of microstructural characterizations and hardness tests.Results showed that a hardening and transition layer(TL)would be generated along the welding interface,and the width and hardening degree of the TL would increase with the heat input.Meanwhile,heavy load hardness tests showed that highly severe inhomogeneous plastic deformation and the microcrack would be generated in the interfacial region and the welding interface respectively in the highest heat input sample(1.03 kJ/mm).These results indicate that the increase in heat input would deteriorate the bonding performance of DMW joints.Further microstructural observations showed that the higher hardening degree of the highest heat input sample was mainly attributed to the stronger grain boundary,solution,and dislocation strengthening effects.

改进Oliver-Pharr法在铁电单晶纳米压痕中的应用

为解决传统Oliver-Pharr法无法给出接触刚度随压入深度的连续变化关系问题,考虑塑性压痕与周围弹性基体间残余接触应力之间影响,引入虚拟载荷,提出改进Oliver-Pharr法.该方法可连续确定接触刚度,不需要对压头的面积函数进行预先校正.将该方法应用到PIN-PMN-PT铁电单晶纳米压痕实验数据分析中,计算了其接触刚度、弹性模量及硬度,并与连续刚度测量法的测量结果进行了比较.研究结果表明:该方法的计算结果与连续刚度测量法的测量结果吻合度高,改进Oliver-Pharr法有效可行.

非理想情况下薄膜Oliver&Pharr压入硬度的校正

通过量纲分析及有限元数值计算,提出了Berkovich压头尖端钝化情况下残余压应力场中薄膜Oliver&Pharr压入硬度的校正公式及相应校正程序。根据该方法,只要测定薄膜纳米压入加卸载曲线、薄膜中的残余压应力及压头的相对钝化量,便可最终确定理想压头下无残余应力时的薄膜硬度。

Relationship between Hardness and Deformation during Cold Rolling Process of Complex Profles

The hardening on surface of complex profles such as thread and spline manufactured by cold rolling can efectively improve the mechanical properties and surface quality of rolled parts. The distribution of hardness in superfcial layer is closely related to the deformation by rolling. To establish the suitable correlation model for describing the relationship between strain and hardness during cold rolling forming process of complex profles is helpful to the optimization of rolling parameters and improvement of rolling process. In this study, a physical analog experiment refecting the uneven deformation during complex-profle rolling process has been extracted and designed, and then the large date set (more than 400 data points) of training samples refecting the local deformation characteristics of complexprofle rolling have been obtained. Several types of polynomials and power functions were adopted in regression analysis, and the regression correlation models of 45# steel were evaluated by the single-pass and multi-pass physical analog experiments and the complex-profle rolling experiment. The results indicated that the predicting accuracy of polynomial regression model is better in the strain range (i.e., ε < 1.2) of training samples, and the correlation relationship between strain and hardness out strain range (i.e., ε > 1.2) of training samples can be well described by power regression model;so the correlation relationship between strain and hardness during complex-profle rolling process of 45# steel can be characterized by a segmented function such as third-order polynomial in the range ε < 1.2 and power function with a ftting constant in the range ε > 1.2;and the predicting error of the regression model by segmented function is less than 10%.

Dietary protein levels changed the hardness of muscle by acting on muscle fiber growth and the metabolism of collagen in sub-adult grass carp(Ctenopharyngodon idella)

Background:Nutrient regulation has been proven to be an effective way to improve the flesh quality in fish.As a necessary nutrient for fish growth,protein accounts for the highest proportion in the fish diet and is expensive.Although our team found that the effect of protein on the muscle hardness of grass carp was probably related to an increased collagen content,the mechanism for this effect has not been deeply explored.Moreover,few studies have explored the protein requirements of sub-adult grass crap(Ctenopharyngodon idella).Therefore,the effects of different dietary protein levels on the growth performance,nutritional value,muscle hardness,muscle fiber growth,collagen metabolism and related molecule expression in grass carp were investigated.Methods:A total of 450 healthy grass carp(721.16±1.98 g)were selected and assigned randomly to six experimen-tal groups with three replicates each(n=25/replicate),and were fed six diets with 15.91%,19.39%,22.10%,25.59%,28.53%and 31.42%protein for 60 d.Results:Appropriate levels of dietary protein increased the feed intake,percentage weight gain,specific growth rate,body composition,unsaturated fatty acid content in muscle,partial free amino acid content in muscle,and muscle hardness of grass carp.These protein levels also increased the muscle fiber density,the frequency of new muscle fibers,the contents of collagen and IGF-1,and the enzyme activities of prolyl 4-hydroxylases and lysyloxidase,and decreased the activity of matrix metalloproteinase-2.At the molecular level,the optimal dietary protein increased col-lagen type Iα1(Colα1),Colα2,PI3K,Akt,S6K1,La ribonucleoprotein domain family member 6a(LARP6a),TGF-β1,Smad2,Smad4,Smad3,tissue inhibitor of metalloproteinase-2,MyoD,Myf5,MyoG and MyHC relative mRNA levels.The levels of the myostatin-1 and myostatin-2 genes were downregulated,and the protein expression levels of p-Smad2,Smad2,Smad4,p-Akt,Akt,LARP6 and Smad3 were increased.Conclusions:The appropriate levels of dietary protein promoted the growth of sub-adult grass carp and improved muscle hardness by promoting the growth of muscle fibers,improving collagen synthesis and depressing collagen degradation.In addition,the dietary protein requirements of sub-adult grass carp were 26.21%and 24.85%according to the quadratic regression analysis of growth performance(SGR)and the muscle hardness(collagen content),respectively.

Friction welding influence on microstructure,microhardness and hardness behavior of CrNiMo steel(AISI 316)

For joining high Cr,Ni and Mo austenitic stainless steel(AISI 316)by direct drive friction welding(DDFW),with friction weld-ing conditions:rotation speed of 3000 r/min,friction time of 10 s,friction pressure of 130 MPa,forge time of 5 s and forge pressure of 260 MPa.The results of microstructure showed that the temperature at the interface reached 819℃while forge applied between 357-237℃,which subdivided welded joint into four distinct regions of highly plastically deformed zone(HPDZ),thermo-mechanically affected zone(TMAZ),heat affected zone(HAZ)and the base metal,with grain size about 10µm,100µm,90µm and 30µm respectively.These re-gions were created due to dynamic recrystallization(DRX)at the interface and thermo-mechanical deformation with heat diffusion in the neighboring regions.Whereas,high level of microhardness about 300 HV0.1 and hardness roughly 240 Hv10 at the interface due to HPDZ creation while low level of 240 HV0.1 for microhardness and moderately of 205 HV10 for hardness in neighboring regions.

Influence of quenching medium on the dendrite morphology,hardness,and tribological behaviour of cast Cu-Ni-Sn spinodal alloy for defence application

Cu-Ni-Sn spinodal alloys(Spinodal bronze)are potential materials with robust applications in components associated with defence applications like bearings,propellers,bushes,and shafts of heavily loaded aircraft,off-road vehicles,and warships.This paper presents a comparative study using water,Brine solution,and SAE 40 oil as the quenching media in regular bronze(Cu-6Sn)and spinodal bronze(Cu-9Ni-6Sn)alloys.Morphological analysis was conducted by optical microscopy,transmission electron microscopy(TEM),and X-ray diffraction technique(XRD)on bronze and spinodal bronze samples immersed in the three different quenching media to understand the grain size and hardness values better.Tribological analysis was performed to analyze the effect of quenching media on the wear aspects of bronze and spinodal bronze samples.The hardness value of the brine-aged spinodal bronze samples was as high as 320 Hv,and the grain size was very low in the range of 60μm.A quantitative comparison between brine-aged regular bronze and brine-aged spinodal bronze showed that the hardness(Hv)was almost 80%higher for brine-aged spinodal bronze.Further,the grain size was approximately 30%finer for spinodal bronze when compared with regular bronze.When the load was increased in spinodal bronze samples,there was an initial dip in wear rate followed by a marginal increase.There was a steady increase in friction coefficient with a rise in load for brine-aged regular bronze and spinodal bronze samples.These results indicate that brine solution is the most effective quenching medium for cast Cu-Ni-Sn spinodal alloys.

Effect of Dynamic Strain Aging on Hardness in the Heat-Affected Zone of SUS316 Steel Welds

DSA(dynamic strain aging)phenomenon in SUS316 steel was investigated using isothermal and non-isothermal tensile tests of simulated HAZ(heat-affected zone)thermal cycles.Isothermal tensile tests were performed on SUS316 in the peak temperature range of 20-700°C,with strain rates varying from 4.2×10^(-3)to 4.2×10^(-5)s^(-1).Based on the appearance of discontinuous plastic flows,expressed as serrations,and the hardening phenomenon of the tensile samples,the conditions for the occurrence of DSA in the SUS316 steel were investigated.Furthermore,the extent of hardening due to DSA was evaluated by comparing the hardness values of the SUS316 and SUS316EHP steels after the tensile tests.To confirm the effect of DSA on hardness in the HAZ of the welded SUS316 steel,non-isothermal tensile tests of the simulated HAZ thermal cycles were performed using a Thermec Master.The relationship between the increase in Vickers hardness due to DSA and the strain in the HAZ was determined;the effect of DSA on hardness in the HAZ could be predicted.The DSA in SUS316 steel was found to be mainly attributed to the dynamic interaction of dislocations with C and N interstitial atoms during high-temperature deformation.

长江三角洲北翼第一硬土层理化特征及其地质成因

在长江河口两翼广泛分布第一硬土层(FHSL),研究其形成机制及工程地质特性对工程建设具有很好的指导意义。根据调查资料(钻孔935个,累计进尺42128 m)和试验资料,首次精确确认了长江河口北翼第一硬土层分布界线,研究了第一硬土层的形成年代、粒度特征、地球化学特征、工程地质特性等。研究表明:第一硬土层形成年龄为20~11 ka B.P.(多个光释光和14C测年资料);硬土层含水率随深度的增加有增大的趋势,表明气候自下向上逐渐变凉和变干;第一硬土层的颗粒级配、粒度分布频率曲线、C-M沉积图等特征显示,第一硬土层主要由粉砂、极细砂和粘土粒级组成,样品的粒度频率曲线主要呈单峰分布,反映出物质沉积前所受搬运营力性质单一,土体颗粒沉积以均匀悬浮占绝对优势,沉积环境是一种相对稳定的低能环境。第一硬土层的发育受气候控制,大致可以分为3个阶段:第1阶段(20~15 ka B.P.)为沉积与成土交替作用时期,且以沉积作用为主,硬土层剖面厚度主要受该阶段控制,至末次盛冰期结束;第2阶段(15~11 ka B.P.)为暴露成土期,这时洪水不能形成越岸沉积,加积作用基本停止,硬土层厚度不再明显增加,已形成的第一硬土区域受到频繁变迁的分合河网的侵蚀切割,形成多条不规则古河道和台地,硬土层逐渐脱水成陆,经历了风化成壤的过程;第3阶段(11 ka B.P.至今)为淹埋期,随着全新世的到来,气候变暖,海平面不断上升,硬土层被其上覆的海相沉积层掩埋,成岩作用开始直到现今。土体易溶盐含量较高,为典型氯盐渍土类型,自下而上具有从低变高的趋势,为海相层覆盖硬土层以后成岩过程造成的。

不同摩擦副条件下二硫化钼薄膜的摩擦学性能研究

为了研究MoS_(2)-Ti薄膜与9Cr18钢、W-DLC和DLC薄膜的摩擦学行为,分别采用磁控溅射技术和等离子体增强化学气相沉积技术在9Cr18钢表面沉积了MoS_(2)-Ti薄膜、W-DLC和DLC薄膜。用扫描电子显微镜(SEM)、能量色散谱仪(EDS)和X射线衍射仪(XRD)研究了薄膜的表面形貌、化学成分和相组成。利用纳米压痕仪和球-盘摩擦试验机对不同薄膜的纳米硬度和摩擦学性能进行了分析。研究结果表明,MoS_(2)-Ti薄膜与DLC薄膜的摩擦因数和磨损率最小。相比MoS_(2)-Ti薄膜与不镀膜的9Cr18钢球摩擦副,MoS_(2)-Ti薄膜与W-DLC薄膜摩擦副的摩擦因数和磨损率没有减小。MoS_(2)-Ti薄膜与W-DLC薄膜摩擦副的磨损机制为磨粒磨损和黏着磨损,与DLC薄膜摩擦副的磨损机制为黏着磨损。摩擦副表面沉积DLC薄膜有助于降低MoS_(2)-Ti薄膜的摩擦因数和磨损率。

氧化物光学薄膜的压入硬度研究

为了评价离子源辅助对不同氧化物薄膜的影响,采用不同的镀膜设备沉积了TiO_(2)、Ta_(2)O_(5)、ZrO_(2)、SiO_(2)氧化物单层膜,用椭偏仪测量了其折射率和厚度,并用纳米压痕仪测量了不同载荷下材料的杨氏模量和纳米硬度,比较了不同离子源沉积条件下膜层这两个参数的变化。结果表明,离子源辅助能有效增加膜层杨氏模量和压入硬度,TiO_(2)增加了2 GPa,Ta_(2)O_(5)增加了4 GPa,ZrO_(2)增加了2 GPa,和膜层的折射率变化趋势是一致的。纳米压痕法也可作为评价离子源轰击能力的一种手段。

超声振动在矿山煤岩致裂中的研究进展与展望

为了推动超声振动致裂煤岩体技术的发展,提高矿山煤层气增产及硬岩掘进的效率,回顾了超声波技术的发展历程,综述了超声振动在致裂煤岩体方面的应用现状与研究进展,明确了超声振动在煤岩致裂领域存在的关键阻碍性技术难题及发展趋势。(1)总结了传统技术在矿山煤层气增产和硬岩掘进领域存在的技术问题,介绍了超声波技术的独特优势及应用领域,阐述了超声波发生器和超声波换能器的发展阶段及相应性能;(2)归结了超声振动煤层气促解增渗装置及流程,分析了超声振动煤层气促解增产现状,阐明了超声空化效应、机械振动效应、热效应作用下煤层气降压、加速、位能及动能增加进而促进其解吸增渗的机制;(3)归纳了超声振动破岩装置及流程,阐述了超声振动破碎硬岩的进展,揭示了超声振动产生的机械振动效应与热效应作用下疲劳损伤、微裂纹亚临界扩展、矿物颗粒不均匀热膨胀或矿物相变、岩石物理力学特性劣化导致硬岩破碎的内在机理;(4)针对超声波发生器、换能器及超声振动在矿山致裂煤岩体中的局限度,对未来超声振动致裂煤岩体在现场高效应用的研究重点提出了4点建议:高性能防爆型超声波发生器和换能器的研发,超声振动促解增渗机理的深入分析及管线技术框架设计,多功能及多场耦合室内超声振动致裂煤岩体设备研制与试验,井下抗干扰超声振动设备的研发应用。

政府债务预算硬约束与地方财政可持续性提升

地方政府债务风险的不断积累已成为地方财政可持续性的最大阻碍。以新《预算法》实施后,地方政府债务管理的“开前门”和“关后门”两个阶段改革为准自然实验,分析了政府债务预算硬约束对地方财政可持续性的影响。研究发现:地方政府债务管理的两阶段改革都对地方财政可持续性具有显著的正向提升影响;从作用机制来看,“开前门”和“关后门”阶段改革分别通过财政收支巩固和债务规模控制来发挥对地方财政可持续性的有效作用;异质性分析来看,地方政府举债行为激励较弱和财政监管力度较高的地方,政府债务预算硬约束对地方财政可持续性的正向效应会更加显著。研究结果为推进债务预算硬约束来防范地方政府债务风险和提升地方财政可持续性提供了政策启示。

巷帮煤体整体滑脱型冲击地压锚杆防冲支护原理及工程实践

冲击地压是目前严重影响煤炭安全有效开采的灾害之一,研究锚杆防冲支护原理和技术对防治巷道冲击地压灾害具有重要意义和价值。通过对巷帮煤体整体冲入型冲击地压发生的地质条件以及破坏特征进行总结分析,认为坚硬顶板与坚硬煤层是此类型冲击地压的重要地质特征,而巷帮煤体整体滑脱是其主要冲击破坏特征。在此基础上,以巷帮滑脱煤体为研究对象,建立了顶板-巷道-底板复合结构体力学模型,建立了巷帮煤体发生水平滑移的极限平衡方程,并对各个参数进行分析。结果表明:由于顶板反弹使巷帮煤体竖直方向压力降低,巷帮煤体被构造应力推入巷道发生冲击地压。基于该发生机制模型,认为目前的锚杆支护设计体系在防治巷帮煤体冲入型冲击地压存在不足,并基于其发生和破坏特征,建立了针对巷帮煤体整体滑脱型冲击地压的锚杆防冲支护设计原则,即将顶和底帮锚杆锚固端分别穿层打入稳定的顶底板内,并使用长锚索取代中部帮锚杆,提供锚杆支护的防冲作用。基于新建立的锚杆防冲支护设计方法,以大屯矿区孔庄煤矿7305工作面防冲支护为工程背景,在宽煤柱段巷帮锚杆支护采取了防冲设计,帮顶、底部锚杆及补强锚索均锚固于顶底板内部,能够有效吸收煤体滑动动能,提高安全性。

煤层瓦斯含量测定技术及装备研究进展

瓦斯含量是煤与瓦斯突出危险预测、煤层瓦斯资源量估算、矿井瓦斯治理工程设计的重要参数。围绕如何在大区域准确快速测定煤层瓦斯含量,依托国家科技重大专项、国家自然科学基金和煤炭企业联合基金等项目科技攻关,在取样、测试方面取得了一定进展。主要表现在如下4个方面:①煤层瓦斯含量测定取样经历了孔口接样、岩心管定点取样、压力引射定点取样和密闭取样4个阶段,密闭取样装备保压能力达到11.5 MPa,煤心直径达到38 mm;②针对不同煤层地质条件,发展形成了顺煤层定向长钻孔密闭取样、底板穿层钻孔密闭取样和顶(底)板梳状定向长钻孔密闭取样3种取样技术;③在河南焦作和山西晋城矿区硬煤层中,顺层定向长钻孔取样深度达到516 m,密闭取样法测得煤层瓦斯含量较常规取样法分别平均提高了0.44倍和1.04倍。在安徽淮南矿区碎软煤层中,穿层钻孔密闭取样深度达到209 m,测得煤层瓦斯含量较常规取样法平均提高了0.26倍;在安徽淮北矿区碎软煤层中,顶(底)板梳状钻孔密闭取样深度达到484 m,测得煤层瓦斯含量较常规取样法平均提高了0.19倍,密闭取样法在煤层瓦斯含量测定精度、探测范围上优于常规取样法;④在瓦斯含量测试方面,除了传统解吸法测试,发展了系列煤矿井下瓦斯含量快速测试装备,可实现最快30 min内测得煤层瓦斯含量,一般用于百米孔内的瓦斯含量测试。提出了煤层瓦斯含量测定密闭取样装备需向小型化、轻量化的方向发展,并能实现随钻密闭取样。在测试上,应根据实际情况确定合理的解吸终止限,并将测试装备和密闭取样装备进一步结合,以实现深孔瓦斯含量快速准确测定。密闭取样技术已成为煤层瓦斯含量大区域精准勘查、预测的主要手段,是煤炭安全高效开采的重要技术保障。

共同结构规范中舭部曲板作为硬角单元的适用条件研究

按照共同结构规范要求,对于船舶舭部板的船体梁极限强度和残存强度计算,规定在一般情况下应将其视为硬角单元,但未明确可以将其视为硬角单元的具体条件。本文利用共同结构规范对于曲板屈曲能力的评估方法和非线性屈曲有限元分析方法,对船舯区域和船舯以外区域的典型几何形状的舭部曲板进行了研究,得到了在共同结构规范要求的船体梁极限强度和残存强度计算中,舭部板可以被视为硬角单元的简要条件。

94份小麦种质Puroindoline和HMW-GS分子检测与品质分析

籽粒硬度和高分子量谷蛋白亚基(HMW-GS)对小麦品质起决定作用,为发掘和利用硬度Puroindoline基因和HMW-GS优异等位变异,提升长江中下游麦区中强筋小麦品质,对长江中下游麦区推广品种以及其他麦区优质推广品种和地方品种共计94份材料进行分子检测和品质分析。结果表明,硬度变幅7.21~72.91,软质类型42份、占44.68%,硬质类型42份、占44.68%,混合类型10份、占10.64%。硬度突变基因型共有5种,包括Pina-D1b/Pinb-D1a、Pina-D1r/Pinb-D1a、Pina-D1s/Pinb-D1a、Pina-D1a/Pinb-D1b和Pina-D1a/Pinb-D1p,数量分别为8份、3份、1份、29份和9份,籽粒硬度表现依次为Pina-D1r/Pinb-D1a>Pina-D1s/Pinb-D1a>Pina-D1b/Pinb-D1a>Pina-D1a/Pinb-D1p>Pina-D1a/Pinb-D1b。HMW-GS分析表明,Glu-A1位点1和Null亚基材料比例分别为53.33%和45.56%,此外有1G330E亚基材料1份;Glu-B1位点7+8和7+9亚基材料比例分别为47.78%和46.67%,此外有14+15亚基材料3份、7OE+8*亚基材料1份、6+8亚基材料1份;Glu-D1位点2+12和5+10亚基材料比例分别为61.11%和38.89%。在微量SDS沉淀值上,Glu-A1位点的1和Null亚基、Glu-B1位点的7+8和7+9亚基无显著差异,Glu-D1位点5+10亚基极显著大于2+12亚基。硬度和SDS沉淀值呈极显著正相关,硬度对SDS沉淀值影响大于HMW-GS。本研究对小麦种质Pin和HMW-GS基因型和品质进行了分析,为小麦品质遗传改良尤其是中强筋小麦品质改良提供了参考。

硬度耦合刚度增强型软体夹持器设计研究

软体夹持器具有良好的顺应性、无损伤和安全的人机交互性能等优点,但由于其材料的特性限制,往往存在刚度不足和夹持力小等问题。文中基于传统的快速气动网络结构,提出了一种硬度耦合结构的刚度增强型软体夹持器的结构方案。首先,结合硅橡胶材料的Yeoh本构模型和静力平衡及虚功原理,建立了刚度增强型软体夹持器的运动学和力学模型,描述了夹持器手指弯曲角度和末端接触力与压强之间的关系;其次,运用ABAQUS软件对不同硬度结构的夹持器进行了有限元分析,制作了夹持器实体,搭建实验台测定了夹持器手指实际变形和末端接触力数据,并通过实际抓取对比试验验证了实际抓取效果。结果表明:相较于传统结构,硬度耦合结构在同为20 kPa的驱动气压下,弯曲角度最大可减小120°;极限压力下,末端接触力最大增加0.1 N;最优设计为05HA结构,抓取物的质量是传统型的3.42倍。

高跟鞋全掌中底硬度对青年女性行走过程中步态特征与稳定性的影响

为了减少长期穿着高跟鞋对女性足部健康产生的不利影响,研究选取40名青年女性穿着3双不同全掌中底硬度的高跟鞋,采用Footscan^(R)足底压力测量系统与RSscan^(R)测力台同步使用,对其自然行走时步态周期、足底压力中心轨迹以及峰值压力、峰值压强、压强-时间积分等足底动力学特征进行测试。结果显示:随着全掌中底硬度的降低,前掌着地时间变长,全掌着地时间变短,足部外翻程度明显减小,内翻程度明显变大。较低的中底硬度具有良好的缓冲性能和保护性能。研究对于提升高跟鞋穿着稳定性及舒适性具有重要的参考价值,可为制鞋行业在高跟鞋中底材质的选择与研发方面提供科学可靠的理论支持。