期刊文献+
共找到18,672篇文章
< 1 2 250 >
每页显示 20 50 100
A novel one-time-programmable memory unit based on Schottky-type p-GaN diode
1
作者 Chao Feng Xinyue Dai +4 位作者 Qimeng Jiang Sen Huang Jie Fan Xinhua Wang Xinyu Liu 《Journal of Semiconductors》 EI CAS CSCD 2024年第3期53-57,共5页
In this work,a novel one-time-programmable memory unit based on a Schottky-type p-GaN diode is proposed.During the programming process,the junction switches from a high-resistance state to a low-resistance state throu... In this work,a novel one-time-programmable memory unit based on a Schottky-type p-GaN diode is proposed.During the programming process,the junction switches from a high-resistance state to a low-resistance state through Schottky junction breakdown,and the state is permanently preserved.The memory unit features a current ratio of more than 10^(3),a read voltage window of 6 V,a programming time of less than 10^(−4)s,a stability of more than 108 read cycles,and a lifetime of far more than 10 years.Besides,the fabrication of the device is fully compatible with commercial Si-based GaN process platforms,which is of great significance for the realization of low-cost read-only memory in all-GaN integration. 展开更多
关键词 wide-bandgap semiconductor one-time programmable Schottky-type p-GaN diode read-only memory device
下载PDF
Evaluation of the Effectiveness and Safety of One-Time Endodontics in the Treatment of Chronic Apical Periodontitis with Sinus Tract in Pediatric Deciduous Teeth
2
作者 Yi Liu 《Journal of Clinical and Nursing Research》 2024年第6期111-116,共6页
Objective:To observe the effectiveness and safety of one-time endodontics in the treatment of chronic apical periodontitis with sinus tract in pediatric deciduous teeth.Methods:109 cases of children with chronic apica... Objective:To observe the effectiveness and safety of one-time endodontics in the treatment of chronic apical periodontitis with sinus tract in pediatric deciduous teeth.Methods:109 cases of children with chronic apical periodontitis with sinus tract in the deciduous teeth treated in our hospital from January 2022 to December 2023 were selected and grouped by the randomized numerical table method,with 54 cases in the experimental group and 55 cases in the control group.The experimental group was treated with one-time endodontics and the control group was treated with conventional endodontics.Results:After the treatment,the total effective rate of treatment was higher in the experimental group than in the control group(P<0.05);the incidence of adverse events was lower in the experimental group than in the control group(P<0.05);the satisfaction of the children's family members was higher in the experimental group than in the control group(P<0.05);the pain duration was lower in the experimental group than in the control group(P<0.05).Conclusion:In the experimental group,children with chronic apical periodontitis with sinus tract of the deciduous teeth were given one-time endodontic treatment,and the results of its implementation were relatively good. 展开更多
关键词 one-time endodontics Chronic apical periodontitis with sinus tract Pediatric deciduous teeth Therapeutic effectiveness SAFETY
下载PDF
A numerical method for the simulation of freight train emergency braking operations based on the UIC braked weight percentage
3
作者 N.Bosso Matteo Magelli N.Zampieri 《Railway Engineering Science》 2023年第2期162-171,共10页
The present paper shows the development of a strategy for the calculation of the air brake forces of European freight trains. The model is built to upgrade the existing Politecnico di Torino longitudinal train dynamic... The present paper shows the development of a strategy for the calculation of the air brake forces of European freight trains. The model is built to upgrade the existing Politecnico di Torino longitudinal train dynamics(LTD) code LTDPoliTo, which was originally unable to account for air brake forces. The proposed model uses an empirical exponential function to calculate the air brake forces during the simulation, while the maximum normal force on the brake friction elements is calculated according to the indication of the vehicle braked weight percentage.Hence, the model does not require to simulate in detail the fluid dynamics in the brake pipe nor to precisely know the main parameters of the braking system mounted on each vehicle. The model parameters are tuned to minimize the difference between the braking distance computed by the LTDPoliTo code and the value prescribed by the UIC544-1 leaflet in emergency braking operations. Simulations are run for different configurations of freight train compositions including a variable number of Shimmns wagons trailed by an E402B locomotive at the head of the train, as suggested in a reference literature paper. The results of the proposed method are in good agreement with the target braking distances calculated according to the international rules. 展开更多
关键词 Railway brake modelling Emergency braking UIC braking system Braked weight Longitudinal train dynamics
下载PDF
Blended Regenerative Anti-Lock Braking System and Electronic Wedge Brake Coordinate Control Ensuring Maximal Energy Recovery and Stability of All-Wheel-Motor-Drive Electric Vehicles
4
作者 Mahmoud Said Jneid Péter Harth 《Journal of Transportation Technologies》 2023年第3期465-495,共31页
ABS is an active safety system which showed a valuable contribution to vehicle safety and stability since it was first introduced. Recently, EVs with in-wheel-motors have drawn increasing attention owing to their grea... ABS is an active safety system which showed a valuable contribution to vehicle safety and stability since it was first introduced. Recently, EVs with in-wheel-motors have drawn increasing attention owing to their greatest advantages. Wheels torques are precisely and swiftly controlled thanks to electric motors and their advanced driving techniques. In this paper, a regenerative-ABS control RABS is proposed for all-in-wheel-motors-drive EVs. The RABS is realized as a pure electronic braking system called brake-by-wire. A coordination strategy is suggested to control RABS compromising three layers. First, wheels slip control takes place, and braking torque is calculated in the higher layer. In the coordinate interlayer, torque is allocated between actuators ensuring maximal energy recovery and vehicle stability. While in the lower layer, actuator control is performed. The RABS effectiveness is validated on a 3-DOF EVSimulink model through two straight-line braking manoeuvres with low and high initial speeds of 50 km/h and 150 km/h, respectively. Both regular and emergency braking manoeuvres are considered with ABS enabled and disabled for comparison. Simulation results showed the high performance of the proposed RABS control in terms of vehicle stability, brake response, stopping distance, and battery re-charging. 展开更多
关键词 EV Stability Regenerative-ABS Blended braking Energy Recovery In-Wheel-Motor Electronic-Wedge-Brake Brake-by-Wire
下载PDF
Copper-Free Resin-Based Braking Materials:A New Approach for Substituting Copper with Fly-Ash Cenospheres in Composites
5
作者 Kaikui Zheng Youxi Lin +2 位作者 Shanmin You Zhiying Ren Jianmeng Huang 《Chinese Journal of Mechanical Engineering》 SCIE EI CAS CSCD 2024年第2期401-412,共12页
Copper particles emitted from braking have become a significant source of environmental pollution.However,copper plays a crucial role in resin-based braking materials.Developing high-performance braking materials with... Copper particles emitted from braking have become a significant source of environmental pollution.However,copper plays a crucial role in resin-based braking materials.Developing high-performance braking materials without copper has become a significant challenge.In this paper,the resin-based braking materials were filled with flyash cenospheres to develop copper-free braking materials.The effects of fly-ash cenospheres on the physical properties,mechanical and friction and wear properties of braking materials were studied.Furthermore,the wear mechanism of copper-free resin-based braking materials filled with fly-ash cenospheres was discussed.The results indicate that the inclusion of fly-ash cenospheres in the braking materials improved their thermal stability,hardness and impact strength,reduced their density,effectively increased the friction coefficient at medium and high temperatures,and enhanced the heat-fade resistance of the braking materials.The inclusion of fly-ash cenospheres contributed to the formation of surface friction film during the friction process of the braking materials,and facilitated the transition of form from abrasive wear to adhesive wear.At 100-350℃,the friction coefficient of the optimal formulation is in the range of 0.57-0.61,and the wear rate is in the range(0.29-0.65)×10^(-7) cm^(3)·N^(-1)·m^(-1),demonstrating excellent resistance to heat-fade and stability in friction coefficient.This research proposes the use of fly-ash cenospheres as a substitute for environmentally harmful and expensive copper in brake materials,which not only improves the performance of braking materials but also reduces their costs. 展开更多
关键词 Fly-ash cenospheres braking materials Friction and wear Heat-fade resistance Wear form
下载PDF
Thermal fatigue and wear of compacted graphite iron brake discs with various thermomechanical properties
6
作者 Gui-quan Wang Zhuo Xu +2 位作者 Zhong-li Liu Xiang Chen Yan-xiang Li 《China Foundry》 SCIE EI CAS CSCD 2024年第3期248-256,共9页
The increase in payload capacity of trucks has heightened the demand for cost-effective yet high performance brake discs.In this work,the thermal fatigue and wear of compacted graphite iron brake discs were investigat... The increase in payload capacity of trucks has heightened the demand for cost-effective yet high performance brake discs.In this work,the thermal fatigue and wear of compacted graphite iron brake discs were investigated,aiming to provide an experimental foundation for achieving a balance between their thermal and mechanical properties.Compacted graphite iron brake discs with different tensile strengths,macrohardnesses,specific heat capacities and thermal diffusion coefficients were produced by changing the proportion and strength of ferrite.The peak temperature,pressure load and friction coefficient of compacted graphite iron brake discs were analyzed through inertia friction tests.The morphology of thermal cracks and 3D profiles of the worn surfaces were also discussed.It is found that the thermal fatigue of compacted graphite iron discs is determined by their thermal properties.A compacted graphite iron with the highest specific heat capacity and thermal diffusion coefficient exhibits optimal thermal fatigue resistance.Oxidization of the matrix at low temperatures significantly weakens the function of alloy strengthening in hindering the propagation of thermal cracks.Despite the reduced hardness,increasing the ferrite proportion can mitigate wear loss resulting from low disc temperatures and the absence of abrasive wear. 展开更多
关键词 compacted graphite iron brake disc thermomechanical properties thermal fatigue WEAR
下载PDF
Sustainable Biocomposites Materials for Automotive Brake Pad Application:An Overview
7
作者 Joseph O.Dirisu Imhade P.Okokpujie +4 位作者 Olufunmilayo O.Joseph Sunday O.Oyedepo Oluwasegun Falodun Lagouge K.Tartibu Firdaussi D.Shehu 《Journal of Renewable Materials》 EI CAS 2024年第3期485-511,共27页
Research into converting waste into viable eco-friendly products has gained global concern.Using natural fibres and pulverized metallic waste becomes necessary to reduce noxious environmental emissions due to indiscri... Research into converting waste into viable eco-friendly products has gained global concern.Using natural fibres and pulverized metallic waste becomes necessary to reduce noxious environmental emissions due to indiscriminately occupying the land.This study reviews the literature in the broad area of green composites in search of materials that can be used in automotive brake pads.Materials made by biocomposite,rather than fossil fuels,will be favoured.A database containing the tribo-mechanical performance of numerous potential components for the future green composite was established using the technical details of bio-polymers and natural reinforcements.The development of materials with diverse compositions and varying proportions is now conceivable,and these materials can be permanently connected in fully regulated processes.This explanation demonstrates that all of these variables affect friction coefficient,resistance to wear from friction and high temperatures,and the operating life of brake pads to varying degrees.In this study,renewable materials for the matrix and reinforcement are screened to determine which have sufficient strength,coefficient of friction,wear resistance properties,and reasonable costs,making them a feasible option for a green composite.The most significant,intriguing,and unusual materials used in manufacturing brake pads are gathered in this review,which also analyzes how they affect the tribological characteristics of the pads. 展开更多
关键词 Asbestos brake pad BIOCOMPOSITES green composite mechanical properties natural reinforcement WASTE
下载PDF
Numerical and Experimental Analysis of the Aerodynamic Torque for Axle-Mounted Train Brake Discs
8
作者 Nan Liu Chen Hong +4 位作者 Xinchao Su Xing Jin Chen Jiang Yuqi Shi Bingkun Wang 《Fluid Dynamics & Materials Processing》 EI 2024年第8期1867-1882,共16页
As the velocity of a train increases,the corresponding air pumping power consumption of the brake discs increases proportionally.In the present experimental study,a standard axle-mounted brake disc with circumferentia... As the velocity of a train increases,the corresponding air pumping power consumption of the brake discs increases proportionally.In the present experimental study,a standard axle-mounted brake disc with circumferential pillars was analyzed using a 1:1 scale model and a test rig in a wind tunnel.In particular,three upstream velocities were selected on the basis of earlier investigations of trains operating at 160,250,and 400 km/h,respectively.Moreover,3D steady computational fluid dynamics(CFD)simulations of the flow field were conducted to compare with the wind tunnel test outcomes.The results for a 3-car train at 180 km/h demonstrated:(1)good agreement between the air resistance torques obtained from the wind tunnel tests and the related numerical results,with differences ranging from 0.95%to 5.88%;(2)discrepancies ranging from 3.2 to 3.8 N·m;(3)cooling ribs contributing more than 60%of the air resistance torque;(4)the fast rotation of brake discs causing a significantly different flow field near the bogie area,resulting in 25 times more air pumping power loss than that obtained in the stationary brake-disc case. 展开更多
关键词 Axle-mounted train brake disc aerodynamic torque wind tunnel test numerical simulation
下载PDF
Regenerative Braking Energy Recovery System of Metro Train Based on Dual-Mode Power Management
9
作者 Feng Zhao Xiaotong Zhu +1 位作者 Xiaoqiang Chen Ying Wang 《Energy Engineering》 EI 2024年第9期2585-2601,共17页
In order to fully utilize the regenerative braking energy of metro trains and stabilize the metro DC traction busbar voltage,a hybrid regenerative braking energy recovery system with a dual-mode power management strat... In order to fully utilize the regenerative braking energy of metro trains and stabilize the metro DC traction busbar voltage,a hybrid regenerative braking energy recovery system with a dual-mode power management strategy is proposed.Firstly,the construction of the hybrid regenerative braking energy recovery system is explained.Then,based on the power demand of low-voltage load in metro stations,a dual-mode power management strategy is proposed to allocate the reference power of each system according to the different working conditions,and the control methods of each system are set.Finally,the correctness and effectiveness of the dual-mode strategy are verified through simulation,and the proposed braking energy utilization scheme is compared with other singleform utilization schemes.The results illustrate that the hybrid system with the dual-mode strategy can effectively recycle the regenerative braking energy of metro train and inhibit the busbar voltage fluctuation;the proposed braking energy utilization scheme has certain advantages on energy recovery and DC bus voltage stabilization compared with other single-form schemes;the proposed power management strategy can correctly allocate the reference power of each system with a lower construction cost. 展开更多
关键词 Metro train regenerative braking energy energy feed-back system energy storage system power management
下载PDF
Dynamic Response Impact of Vehicle Braking on Simply Supported Beam Bridges with Corrugated Steel Webs Based on Vehicle-Bridge Coupled Vibration Analysis
10
作者 Yan Wang Siwen Li Na Wei 《Computer Modeling in Engineering & Sciences》 SCIE EI 2024年第6期3467-3493,共27页
A novel approach for analyzing coupled vibrations between vehicles and bridges is presented,taking into account spatiotemporal effects and mechanical phenomena resulting fromvehicle braking.Efficient modeling and solu... A novel approach for analyzing coupled vibrations between vehicles and bridges is presented,taking into account spatiotemporal effects and mechanical phenomena resulting fromvehicle braking.Efficient modeling and solution of bridge vibrations induced by vehicle deceleration are realized using this method.The method’s validity and reliability are substantiated through numerical examples.A simply supported beam bridge with a corrugated steel web is taken as an example and the effects of parameters such as the initial vehicle speed,braking acceleration,braking location,and road surface roughness on the mid-span displacement and impact factor of the bridge are analyzed.The results show that vehicle braking significantly amplifies mid-span displacement and impact factor responses in comparison to uniform vehicular motion across the bridge.Notably,the influence of wheelto-bridge friction forces is of particular significance and cannot be overlooked.When the vehicle initiates braking near the middle of the span,both the mid-span displacement and impact factor of the bridge exhibit substantial increases,further escalating with higher braking acceleration.Under favorable road surface conditions,the midspan displacement and the impact factor during vehicle braking may exceed the design values stipulated by codes.It is important to note that road surface roughness exerts a more pronounced effect on the impact factor of the bridge in comparison to the effects of vehicle braking. 展开更多
关键词 Corrugated steel web girder bridges simply supported beam bridges vehicle-bridge coupled vibration braking impact factor
下载PDF
Integrated Active Suspension and Anti-Lock Braking Control for Four-Wheel-Independent-Drive Electric Vehicles
11
作者 Ze Zhao Lei Zhang +3 位作者 Xiaoling Ding Zhiqiang Zhang Shaohua Li Liang Gu 《Chinese Journal of Mechanical Engineering》 SCIE EI CAS CSCD 2024年第1期87-98,共12页
This paper presents an integrated control scheme for enhancing the ride comfort and handling performance of a four-wheel-independent-drive electric vehicle through the coordination of active suspension system(ASS)and ... This paper presents an integrated control scheme for enhancing the ride comfort and handling performance of a four-wheel-independent-drive electric vehicle through the coordination of active suspension system(ASS)and anti-lock braking system(ABS).First,a longitudinal-vertical coupled vehicle dynamics model is established by integrating a road input model.Then the coupling mechanisms between longitudinal and vertical vehicle dynamics are analyzed.An ASS-ABS integrated control system is proposed,utilizing an H∞controller for ASS to optimize load transfer effect and a neural network sliding mode control for ABS implementation.Finally,the effectiveness of the proposed control scheme is evaluated through comprehensive tests conducted on a hardware-in-loop(HIL)test platform.The HIL test results demonstrate that the proposed control scheme can significantly improve the braking performance and ride comfort compared to conventional ABS control methods. 展开更多
关键词 Four-wheel-independent-drive electric vehicles Active suspension system(ASS) Anti-lock braking system(ABS) Vertical-longitudinal vehicle dynamics
下载PDF
ISO releases a standard on braking systems of railway vehicles
12
《China Standardization》 2024年第3期15-15,共1页
ISO 24221:2024, Railway applications-Braking system-General requirements, the first of its kind, was recently released. With the leading efforts of National Railway Administration of China, China has made new breakthr... ISO 24221:2024, Railway applications-Braking system-General requirements, the first of its kind, was recently released. With the leading efforts of National Railway Administration of China, China has made new breakthrough in railway international standardization by the development of the international standard. 展开更多
关键词 braking BREAKTHROUGH RAILWAY
下载PDF
Optimal allocation method of electric/air braking force of high-speed train considering axle load transfer
13
作者 Feng Guo Jing He 《High-Speed Railway》 2024年第2期77-84,共8页
Reasonable distribution of braking force is a factor for a smooth,safe,and comfortable braking of trains.A dynamic optimal allocation strategy of electric-air braking force is proposed in this paper to solve the probl... Reasonable distribution of braking force is a factor for a smooth,safe,and comfortable braking of trains.A dynamic optimal allocation strategy of electric-air braking force is proposed in this paper to solve the problem of the lack of consideration of adhesion difference of train wheelsets in the existing high-speed train electric-air braking force optimal allocation strategies.In this method,the braking strategy gives priority to the use of electric braking force.The force model of a single train in the braking process is analyzed to calculate the change of adhesion between the wheel and rail of each wheelset after axle load transfer,and then the adhesion of the train is estimated in real time.Next,with the goal of maximizing the total adhesion utilization ratio of trailer/motor vehicles,a linear programming distribution function is constructed.The proportional coefficient of adhesion utilization ratio of each train and the application upper limit of braking force in the function is updated according to the change time point of wheelset adhesion.Finally,the braking force is dynamically allocated.The simulation results of Matlab/Simulink show that the proposed algorithm not only uses the different adhesion limits of each trailer to reduce the total amount of braking force undertaken by the motor vehicle,but also considers the adhesion difference of each wheelset.The strategy can effectively reduce the risk and time of motor vehicles during the braking process and improve the stability of the train braking. 展开更多
关键词 braking force allocation WHEELSET Dynamicity Axle load transfer total Adhesion utilization ratio
下载PDF
Virtually coupled train set control subject to space-time separation:A distributed economic MPC approach with emergency braking configuration
14
作者 Xiaolin Luo Tao Tang +1 位作者 Le Wang Hongjie Liu 《High-Speed Railway》 2024年第3期143-152,共10页
The emerging virtual coupling technology aims to operate multiple train units in a Virtually Coupled Train Set(VCTS)at a minimal but safe distance.To guarantee collision avoidance,the safety distance should be calcula... The emerging virtual coupling technology aims to operate multiple train units in a Virtually Coupled Train Set(VCTS)at a minimal but safe distance.To guarantee collision avoidance,the safety distance should be calculated using the state-of-the-art space-time separation principle that separates the Emergency Braking(EB)trajectories of two successive units during the whole EB process.In this case,the minimal safety distance is usually numerically calculated without an analytic formulation.Thus,the constrained VCTS control problem is hard to address with space-time separation,which is still a gap in the existing literature.To solve this problem,we propose a Distributed Economic Model Predictive Control(DEMPC)approach with computation efficiency and theoretical guarantee.Specifically,to alleviate the computation burden,we transform implicit safety constraints into explicitly linear ones,such that the optimal control problem in DEMPC is a quadratic programming problem that can be solved efficiently.For theoretical analysis,sufficient conditions are derived to guarantee the recursive feasibility and stability of DEMPC,employing compatibility constraints,tube techniques and terminal ingredient tuning.Moreover,we extend our approach with globally optimal and distributed online EB configuration methods to shorten the minimal distance among VCTS.Finally,experimental results demonstrate the performance and advantages of the proposed approaches. 展开更多
关键词 Virtually coupled train set Space-time separation Economic model predictive control Distributed model predictive control Emergency braking configuration
下载PDF
Thermal analysis for brake disks of SiC/6061 Al alloy co-continuous composite for CRH3 during emergency braking considering airflow cooling 被引量:13
15
作者 姜澜 姜艳丽 +2 位作者 喻亮 苏楠 丁友东 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2012年第11期2783-2791,共9页
The mass of high-speed trains can be reduced using the brake disk prepared with SiC network ceramic frame reinforced 6061 aluminum alloy composite (SiCn/Al). The thermal and stress analyses of SiCn/Al brake disk dur... The mass of high-speed trains can be reduced using the brake disk prepared with SiC network ceramic frame reinforced 6061 aluminum alloy composite (SiCn/Al). The thermal and stress analyses of SiCn/Al brake disk during emergency braking at a speed of 300 km/h considering airflow cooling were investigated using finite element (FE) and computational fluid dynamics (CFD) methods. All three modes of heat transfer (conduction, convection and radiation) were analyzed along with the design features of the brake assembly and their interfaces. The results suggested that the higher convection coefficients achieved with airflow cooling will not only reduce the maximum temperature in the braking but also reduce the thermal gradients, since heat will be removed faster from hotter parts of the disk. Airflow cooling should be effective to reduce the risk of hot spot formation and disc thermal distortion. The highest temperature after emergency braking was 461 °C and 359 °C without and with considering airflow cooling, respectively. The equivalent stress could reach 269 MPa and 164 MPa without and with considering airflow cooling, respectively. However, the maximum surface stress may exceed the material yield strength during an emergency braking, which may cause a plastic damage accumulation in a brake disk without cooling. The simulation results are consistent with the experimental results well. 展开更多
关键词 finite element method brake disk co-continuous SiC/6061 composite thermal analysis airflow cool
下载PDF
Distribution and Dissipation of Braking Power of Wet Multidisc Brake 被引量:1
16
作者 阎清东 宿新东 《Journal of Beijing Institute of Technology》 EI CAS 2000年第1期87-93,共7页
To study the distribution and dissipation of braking power of wet multidisc brake and determine thermal load and thermal flux distribution between mated discs, the concept of distributing brake power four times was pu... To study the distribution and dissipation of braking power of wet multidisc brake and determine thermal load and thermal flux distribution between mated discs, the concept of distributing brake power four times was put forward. The third and the fourth distribution of brake power were calculated by using finite element(FE) software ANSYS. The third and the fourth distribution of wet multidisc brake are mainly related to material characteristics of discs during emergency braking, while most of the braking power is carried off during continuous braking. Basis is provided for further analysis of disc failure and applicability of different friction materials. 展开更多
关键词 wet multidisc brake braking power finite element(FE) analysis
下载PDF
Electronic Brake-Force Distribution Control Methods of ABS-Equipped Vehicles During Cornering Braking 被引量:5
17
作者 王国业 刘昭度 +1 位作者 马岳峰 齐志权 《Journal of Beijing Institute of Technology》 EI CAS 2007年第1期34-37,共4页
Based on the dynamics of ABS-equipped vehicles during cornering braking, the electronic brake- force distribution (EBD) control methods of ABS-equipped vehicles during cornering braking are proposed. According to th... Based on the dynamics of ABS-equipped vehicles during cornering braking, the electronic brake- force distribution (EBD) control methods of ABS-equipped vehicles during cornering braking are proposed. According to the dynamics and the tire model under tire adhesion limit, the stability acceptance criteria of vehicles during cornering braking are proposed. According to the stability acceptance criteria and the ABS control, the EBD control methods of ABS-equipped vehicles during cornering braking are implemented by adjusting the threshold values of tires slip independently. The vehicle states during cornering braking at two typical initial velocities of the vehicle are analyzed by the EBD control methods, whose results indicate the EBD control methods can improve the braking performances of the vehicle during cornering braking comparing with the ABS control. 展开更多
关键词 electronic brake-force distribution(EBD) cornering braking control methods
下载PDF
One-time fertilization at first flowering improves lint yield and dry matter partitioning in late planted short-season cotton 被引量:7
18
作者 LUO Hong-hai WANG Qiang +3 位作者 ZHANG Jie-kun WANG Lei-shan LI Ya-bing YANG Guo-zheng 《Journal of Integrative Agriculture》 SCIE CAS CSCD 2020年第2期509-517,共9页
Cotton producers have substantially reduced their inputs(labor,nutrients,and management)mainly by adopting a shortseason cropping management that is characterized by late sowing,high density,and reduced fertilization ... Cotton producers have substantially reduced their inputs(labor,nutrients,and management)mainly by adopting a shortseason cropping management that is characterized by late sowing,high density,and reduced fertilization with one-time application at the first bloom stage without lint yield reduction.However,it has been hypothesized that one-time fertilization at an earlier growth stage could be a more effective and economic management practice.A two-year field experiment was conducted by applying five fertilizer one-time fertilization at 0(FT1),5(FT2),10(FT3),15(FT4),and 20(FT5)days after the first flower appeared in the field and one three-split fertilizer application taken as the conventional control(FT6),making six treatments altogether.Cotton growth period,biomass accumulation,yield,and its formation were quantified.The results showed that the one-time fertilization did not affect the cotton growth progress as compared to FT6,however,the total crop cycles for FT3–FT5 were 3 days shorter.FT1 produced the highest cotton lint yield(1396 kg ha–1),which was similar to the FT6 but higher than the other treatments,and could be attributed to more bolls per unit area and higher lint percentage.Cotton yield was positively correlated with cotton plant biomass accumulated.FT1 had both the highest average(VT)(193.7 kg ha–1 d–1)and the highest maximum(VM)(220.9 kg ha–1 d–1)rates during the fast biomass accumulation period.These results suggest that one-time fertilizer application at the first flower stage might be an adjustment that is more effective than at first bloom,and allowed for easier decision making for application date due to non counting of plants with flowers is needed. 展开更多
关键词 one-time fertilization first flower cotton biomass accumulation yield
下载PDF
One-time sintering process to modify xLi2MnO3(1-x)LiMO2 hollow architecture and studying their enhanced electrochemical performances 被引量:2
19
作者 Renheng Wang Yiling Sun +5 位作者 Kaishuai Yang Junchao Zheng Yan Li Zhengfang Qian Zhenjiang He Shengkui Zhong 《Journal of Energy Chemistry》 SCIE EI CAS CSCD 2020年第11期271-279,共9页
To solve the critical problems of lithium rich cathode materials, e.g., structure instability and short cycle life, we have successfully prepared a ZrO2-coated and Zr-doping xLi2MnO3·(1–x)LiMO2 hollow architectu... To solve the critical problems of lithium rich cathode materials, e.g., structure instability and short cycle life, we have successfully prepared a ZrO2-coated and Zr-doping xLi2MnO3·(1–x)LiMO2 hollow architecture via one-time sintering process. The modified structural materials as lithium-ion cathodes present good structural stability and superior cycle performance in LIBs. The discharge capacity of the ZrO2-coated and Zr-doped hollow pristine is 220 mAh g-1 at the 20th cycle at 0.2 C(discharge capacity loss, 2.7%)and 150 m Ah g-1 at the 100 th cycle at 1 C(discharge capacity loss, 17.7%), respectively. However, hollow pristine electrode only delivers 203 m Ah g-1 at the 20 th cycle at 0.2 C and 124 mAh g-1 at the 100 th cycle at 1 C, respectively, and the corresponding to capacity retention is 92.2% and 72.8%, respectively.Diffusion coefficients of modified hollow pristine electrode are much higher than that of hollow pristine electrode after 100 cycles(approach to 1.4 times). In addition, we simulate the adsorption reaction of HF on the surface of ZrO2-coated layer by the first-principles theory. The calculations prove that the adsorption energy of HF on the surface of ZrO2-coated layer is about-1.699 e V, and the ZrO2-coated layer could protect the hollow spherical xLi2MnO3·(1–x)LiMO2 from erosion by HF. Our results would be applicable for systematic amelioration of high-performance lithium rich material for anode with the respect of practical application. 展开更多
关键词 Lithium rich cathode materials one-time sintering process Coated and doped Electrochemical performances First-principles calculations
下载PDF
Cryptanalysis of the One-Time Proxy Signature Scheme Used in Mobile Agents 被引量:1
20
作者 FUXiao-tong XIAOHong XIAOGuo-zhen 《Wuhan University Journal of Natural Sciences》 EI CAS 2005年第1期183-185,共3页
We ayptanalyze Kim et. al's one-time proxy signature scheme used in mobileagents, and then a successful forgery is introduced It is showed that a dishonest customer cansuccessfully forge a valid one-time proxy sig... We ayptanalyze Kim et. al's one-time proxy signature scheme used in mobileagents, and then a successful forgery is introduced It is showed that a dishonest customer cansuccessfully forge a valid one-time proxy signature by impersonating the stiver Furthermore, he canrequest the server with responsibility for the forged bidding information. 展开更多
关键词 CRYPTANALYSIS proxy signature one-time proxy signature
下载PDF
上一页 1 2 250 下一页 到第
使用帮助 返回顶部