Design and high-power testing of offline conditioning cavity for CiADS RFQ high-power coupler

To validate the design rationality of the power coupler for the RFQ cavity and minimize cavity contamination,we designed a low-loss offline conditioning cavity and conducted high-power testing.This offline cavity features two coupling ports and two tuners,operating at a frequency of 162.5 MHz with a tuning range of 3.2 MHz.Adjusting the installation angle of the coupling ring and the insertion depth of the tuner helps minimize cavity losses.We performed electromagnetic structural and multiphysics simulations,revealing a minimal theoretical power loss of 4.3%.However,when the cavity frequency varied by110 kHz,theoretical power losses increased to10%,necessitating constant tuner adjustments during conditioning.Multiphysics simulations indicated that increased cavity temperature did not affect frequency variation.Upon completion of the offline high-power conditioning platform,we measured the transmission performance,revealing a power loss of 6.3%,exceeding the theoretical calculation.Conditioning utilized efficient automatic range scanning and standing wave resonant methods.To fully condition the power coupler,a 15°phase difference between two standing wave points in the condition-ing system was necessary.Notably,the maximum continuous wave power surpassed 20 kW,exceeding the expected target.

Design and Fabrication of Ultracompact 3-dB MMI Coupler in Silicon-on-Insulator

An ultracompact 3 dB coupler is designed and fabricated in silicon on insulator,based on 1×2 line tapered multimode interference (MMI) coupler.Comparing with the conventional straight MMI coupler,the device is ～40% shorter in length.The device exhibits uniformity of 1 3dB and excess loss of 2 5dB.

Passively Mode Locked Diode-End-Pumped Nd∶YAG Laser with In_(0.25)Ga_(0.75)As as Output Coupler

A novel InGaAs(LT-In 0.25Ga 0.75As) absorber grown by metal organic chemical vapor deposition at low temperature is presented.Using it as well as an output coupler,passive mode locking,which produces pulses as short as several hundred picoseconds for diode-end-pumped Nd∶YAG laser at 1.06μm,is realized.The pulse frequency is 150MHz.

Full Wave Analysis of a Broad Wall Waveguide Slot Coupler

A rigorous analysis of a broad wall slot coupler composed of two crossed rectangular waveguides by using FDTD method is presented. Two types of slots, a longitudinal/transverse slot and a centered-inclined slot, are analyzed. Coupling slot characteristics are obtained, including scattering parameters and the resonant length for different waveguide dimensions and frequencies. The numerical results are all in good agreement with those by the method of moments. A coupler system with a short circuit port is also analyzed to help designing the slot array.

IEC711 coupler频响仿真

仿真耳(IEC711 coupler)广泛地应用于手提电话、耳机等的电声性能测量;介绍了利用有限元方法来获得IEC711 coupler的频响仿真,从而可以给出比等效线路图方法(LPM)更为真实的分析。

Analysis of longitudinal forces of coupler devices in emergency braking process for heavy haul trains

To reduce the longitudinal coupler forces of heavy haul trains and improve the running safety, the velocity method and New-mark method were used for the coupler simulation and numerical integration, and a numerical model on the longitudinal dynamics of heavy haul trains was established. Validation was performed against the experimental data. Using this model, the emergency braking process for a combined marshalling heavy haul train was investigated to obtain the distributions of the longitudinal compressive forces and strokes of coupler devices. Then, the influences of the initial braking velocity, the synchronization time of master and slave locomotives, the coupler stiffness and the vibrator mass on the longitudinal forces and strokes were analyzed. The results show that it should be avoided that the emergency braking starts at a low initial speed. Keeping synchronism between master locomotive and slave locomotives effectively helps to reduce the longitudinal forces. Reducing the coupler stiffness appropriately and adding rigid arm connections, the longitudinal vibration frequency can be brought down and the longitudinal forces will be decreased, which improves the running safety of heavy haul trains. All of these research results can provide a reference for the operation and development of heavy haul trains.

Stabilizing Mechanism and Running Behavior of Couplers on Heavy Haul Trains

Published studies in regard to coupler systems have been mainly focused on the manufacturing process or coupler strength issues. With the ever increasing of tonnage and length of heavy haul trains, lateral in-train forces generated by longitudinal in-train forces and coupler rotations have become a more and more significant safety issue for heavy haul train operations. Derailments caused by excessive lateral in-train forces are frequently reported. This article studies two typical coupler systems used on heavy haul locomotives. Their structures and stabilizing mechanism are analyzed before the corresponding models are developed. Coupler systems models are featured by two distinct stabilizing mechanism models and draft gear models with hysteresis considered. A model set which consists of four locomotives and three coupler systems is developed to study the rotational behavior of different coupler systems and their implications for locomotive dynamics. Simulated results indicate that when the locomotives are equipped with the type B coupler system, locomotives can meet the dynamics standard on tangent tracks; while the dynamics performance on curved tracks is very poor. The maximum longitudinal in-train force for locomotives equipped with the type B coupler system is 2000 kN. Simulations revealed a distinct trend for the type A coupler system. Locomotive dynamics are poorer for the type A case when locomotives are running on tangent tracks, while the dynamics are better for the type A case when locomotives are running on curved tracks. Theoretical studies and simulations carried out in this article suggest that a combination of the two types of stabilizing mechanism can result in a good design which can significantly decrease the relevant derailments.

Room-temperature test system for 162.5 MHz high-power couplers

Fundamental power couplers are crucial components for feeding radio frequency power to accelerating cavities. Couplers must be tested and conditioned on a room-temperature test stand to evaluate and potentially improve their performance before being installed in an accelerating cavity. A new test system has been designed and is under construction at the institute of modern physics.For this test system, multiple conditioning modes, including the pulse mode, CW mode, and amplitude-sweeping mode, have been embedded in the low-level radio frequency system of the test stand. All of these conditioning modes can be run manually or automatically. In addition, a novel test cavity is proposed and has been designed, which facilitates non-contact conditioning and a multi-purpose test stand.

High efficiency and broad bandwidth grating coupler between nanophotonic waveguide and fibre

A high efficiency and broad bandwidth grating coupler between a silicon-on-insulator （SOI） nanophotonic waveguide and fibre is designed and fabricated. Coupling efficiencies of 46% and 25% at a wavelength of 1.55um are achieved by simulation and experiment, respectively. An optical 3 dB bandwidth of 45 mn from 1530 nm to 1575 nm is also obtained in experin, ent. Numerical calculation shows that a tolerance to fabrication error of 10 nm in etch depth is achievable. The measurement results indicate that the alignment error of 112 um results in less than 1 dB additional coupling loss.

CMOS compatible highly efficient grating couplers with a stair-step blaze profile

A novel grating coupler with a stair-step blaze profile is proposed. The coupler is a CMOS process compatible device and can be used for light coupling in optical communication. The blaze profile can be optimized to obtain a high efficiency of 66.7% for the out-of-plane coupling at the centre wavelength of 1595 nm with a 1 dB bandwidth of 41 nm. Five key parameters of the stair-step blaze grating and their effects on the coupling are discussed for the application in L band telecommunication.

Experimental demonstration of single-mode fiber coupling using adaptive fiber coupler

Coupling plane wave into a single-mode fiber （SMF） with high and steady coupling efficiency is crucial for fiber- based free-space laser systems, where random angular jitters are the main influencing factors of fiber coupling. In this paper, we verified a new adaptive-optic device named adaptive fiber coupler （AFC） which could compensate angular jitters and improve the SMF coupling efficiency in some degree. Experiments of SMF coupling under the angular jitter situation using AFC have been achieved. Stochastic parallel gradient descent （SPGD） algorithm is employed as the control strategy, of which the iteration rate is 625 Hz. In closed loop, the coupling efficiency keeps above 65% when angular errors are below 80/3tad. The compensation bandwidth is 35 Hz at sine-jitter of 15 ~rad amplitude with average coupling efficiency of above 60%. Also, experiments with simulated turbulence have been studied. The average coupling efficiency increases from 31.97% in open loop to 61.33% in closed loop, and mean square error （MSE） of coupling efficiency drops from 7.43% to 1.75%.

Design of a High Power Directional Coupler with High Directivity Used in the LHCD Launcher for EAST

A high power waveguide directional coupler was designed to measure the transmitted power and reflected power in the 4.6 GHz LHCD （lower hybrid current drive） launcher for the EAST tokamak. The design principle of the coupler is assessed. Further analysis is performed by CST （computer simulating test） and Ansoft HFSS （high frequency structure simulator） software and the optimal structural parameter is obtained. In addition, finite element code ANSYS is used to determine the temperature distribution in the coupler conductively cooled by forced water. The test results of a directional coupler manufactured according to the design are close to what is expected.

Design and optimization of terahertz directional coupler based on hybrid-cladding hollow waveguide with low confinement loss

We propose a design and optimization for directional coupling in terahertz hybrid-cladding hollow waveguide. It is composed of two square hollow waveguides which touch each other and are surrounded by a metallic layer. By employing the finite element method, the coupling performance and loss property are numerically investigated. Numerical results indi- cate that this directional coupler with hybrid-cladding can realize ultra-narrow-band coupling; it provides a low confinement loss performance： the confinement loss can reach as low as 6.27 × 10-5 cm- 1. Moreover, the further analyses of configura- tion and performance show that confinement loss and frequency range shift for the low-confinement-loss frequency regime can be realized and optimized by appropriately tuning the thickness values of the metallic and dielectric layer. In addition, through the further analysis of coupling performance, the possibilities of realizing ultra-narrow-band couplings in different frequency ranges are demonstrated. It is a powerful candidate for high precision optical fiber sensing, and communication in terahertz splitting fields.

High coupling efficiency and low signal light loss(2+1)×1 coupler

The coupling efficiency of the pump coupler determines the pump light injection capacity of a laser system. Experi- mental analysis of the influences of different factors on the pump coupling efficiency is in accordance with this conclusion. We use two Nufern fibers （400 Ixrn/440 p.m with NA = 0.22） as pump arm, one Nufern fiber （20 μm/400 μm with NA = 0.06/0.46） as a main fiber to make a side-pumping （2 ＋ 1） × 1 coupler. The experimental result shows that the total output power of this （2 ＋ 1） × 1 coupler is about 1160 W, corresponding to a coupling efficiency as high as 98.6%. The loss of signal light is less than 1%.

High-efficiency focusing grating coupler with optimized ultra-short taper

A novel high-efficiency focusing non-uniform grating coupler is proposed to couple light into or off silicon photonic chips for large-scale silicon photonic integration. This kind of grating coupler decreases the transition length of the linking taper between the grating and the single-mode waveguide by at least 80%. The radian of the grating lines and the size of the taper are optimized to improve the coupling efficiency. An experimental coupling efficiency of ~ 68% at 1556.24 nm is obtained after optimization and the whole size of the grating is 12 μm × 30 μm, with a very short taper transition of ~15 μm long.

MINIATURIZED MICROSTRIP BRANCH-LINE COUPLER WITH GOOD HARMONIC SUPPRESSION PERFORMANCE

This paper presents a miniaturized microstrip branch-line coupler with good harmonic suppression performance. The proposed coupler consists of four branch-line sections, each of which is loaded by open-circuit stubs both at the center and the two ends. This type of loading can realize size reduction and harmonic suppression. As an example, a proposed branch-line coupler operating at 1.0 GHz is designed, fabricated and measured. The results show that the proposed branch-line coupler occupies 67% size of a conventional one and has better than 20 dB suppression from 1.9 to 5.8 GHz. Furthermore, the high slop of the transition band ensures good selectivity of the coupler.

Integrated model optocouplers

Utilizing hybrid integration model.the integrated model optocouplers have successfully developed.The design,fabrication and characteristic parameters of the devices are presented.

基于PROFIBUS下DP/DP COUPLER通讯模块的应用

随着工厂自动化水平的不断提高,总线技术被广泛的应用到各类控制之中,PROFIBUS就是目前常用的一种总线形式。通过使用PROFIBUS总线技术可以提高设备的可靠性和抗干扰能力,使设备性能大幅提高。文章主要介绍在石油专用管传输生产线上,不同设备之间通过DP/DP COUPLER通讯模块进行数据交换,用于解决生产中的信息交换的问题,从而为实现工厂自动化提供可行的解决方案。

INDEPENDENTLY-TUNED CONCURRENT DUAL-BAND BRANCH-LINE COUPLER USING VARACTOR

This paper presents a concurrent dual-band branch-line coupler with an independently tunable center frequency. In the proposed architecture, the quarter-wavelength lines, which work at two separated bands concurrently and can be tuned in one of them, are key components. Based on the analysis of ABCD-matrix, a novel hybrid structure and a pair of varactors topology are utilized to achieve concurrent dual-band operation and independent tunability, respectively. Using this configuration, it is convenient to tune the center frequency of the upper band, while the responses of the lower band remain unaltered. To verify the proposed idea, a demonstration is implemented and the simulated results are presented.

INPUT COUPLER FOR Ka BAND TE021 CIRCULAR ELECTRIC MODE OPERATION IN A GYROKLYSTRON AMPLIFIER

An input coupler for the TE021 circular electric mode in a gyroklystron amplifier through using TE811 as a transition coupling mode in a coaxial cavity has been proposed and numerically simulated in a frequency range of Ka-Band with HFSS code. The coupling efficiency of the TE021 mode and the suppression for the TE811 mode in the main cylindrical cavity are deliberately considered by adjusting the position and size of coupling holes as well as the radius of the drift tubes. The numerical results show that the TE21 mode can successfully be excited, and rational coupling efficiency and high mode purity for the TE021 mode in the cylindrical cavity can be reached for the engineering application of gyroklystron amplifier study.