Space-time Block Codes Based on Quasi-Orthogonal Designs

A new space-time block codes based on quasi-orthogonal designs are put forward. First the channel model is formulated. Then the connection between orthogonal /quasi-orthogonal designs and space-time block codes is explored. Finally we make simulations for the transmission of 4 bits/s/Hz and 6 bits/s/Hz using eight transmit antennas using the rate 3/4 quasi-orthogonal space-time block code and the rate 1/2 full-diversity orthogonal space-time block code. Simulation results show that full transmission rate is more important for very low signal noise ratio (SNR) and high bit error probability (BEP), while full diversity is more important for very high SNR and low BEP.

Optimization of Center of Gravity Position and Anti-Wave Plate Angle of Amphibious Unmanned Vehicle Based on Orthogonal Experimental Method

When the amphibious vehicle navigates in water,the angle of the anti-wave plate and the position of the center of gravity greatly influence the navigation characteristics.In the relevant research on reducing the navigation resistance of amphibious vehicles by adjusting the angle of the anti-wave plate,there is a lack of scientific selection of parameters and reasonable research of simulation results by using mathematical methods,and the influence of the center of gravity position on navigation characteristics is not considered at the same time.To study the influence of the combinations of the angle of the anti-wave plate and the position of the center of gravity on the resistance reduction characteristics,a numerical calculation model of the amphibious unmanned vehicle was established by using the theory of computational fluid dynamics,and the experimental data verified the correctness of the numerical model.Based on this numerical model,the navigation characteristics of the amphibious unmanned vehicle were studied when the center of gravity was located at different positions,and the orthogonal experimental design method was used to optimize the parameters of the angle of the anti-wave plate and the position of the center of gravity.The results show that through the parameter optimization analysis based on the orthogonal experimental method,the combination of the optimal angle of the anti-wave plate and the position of the center of gravity is obtained.And the numerical simulation result of resistance is consistent with the predicted optimal solution.Compared with the maximum navigational resistance,the parameter optimization reduces the navigational resistance of the amphibious unmanned vehicle by 24%.

Optimization and Testing for PCR System of Rice by Orthogonal Design

[Objective] This study was to screen the economic or stable PCR system of rice and detect the generality of the selected system in different molecular markers based on PCR.[Method] With DNA extracted from rice leaves by CTAB method as the template,PCR system was optimized by L16(45)orthogonal design.[Result] Clear bands were amplified from 16 different combinations,but the amplification effects and yields had difference.The most economic and applicable system was as follows:20 ng DNA template,150 μmol/L dNT...

Optimization of SRAP-PCR System of Triticum aestivum——Based on Orthogonal Design

[Objective] The aim was to optimize the technical procedure of SRAP-PCR in Triticum aestivum L. [Method] The orthogonal design L16（45） was used to optimize SRAP-PCR amplification system of wheat Fengyou 68 on five factors （Taq polymerase,Mg2＋,DNA template,dNTPs and primer） at four levels. [Result] Effects of the five factors on SRAP-PCR reaction system were Mg2＋Taq polymerasedNTPsDNA templateprimer. Finally,an optimal SRAP-PCR system was established,that was the total 20 μl reaction system containing 2.0 μl 10×PCR Buffer,2.0 U Taq polymerase,2.0 mmol/L Mg2＋,0.2 mmol/L dNTPs,40 ng DNA template and 0.6 μmol/L primer. [Conclusion] The optimum SRAP-PCR system had provided some technical foundations to conduct SRAP genetic analysis for wheat varieties.

Optimization of the Formula of Maca Lozenges by Orthogonal Test

The orthogonal experimental design was used to optimize the formula of maca lozenge and explore the preparation techniques and product property of maca lozenges. With the sensory evaluation of maca lozenge as the indicator, L16 （44） orthogonal design graph was used to select the optimal techniques, and to investigate the stability, heavy metals and microorganisms contents in the tablets. The optimal formula was 80% of maca power, 12% of Rhodiola rosea powder, and 6% of Angelica sinensis powder, where the comprehensive sensory index reached 246. Moreover, under the optimal conditions, various kinds of heavy metals contents were in consistent with the GB164740 standards, and there was no significant change in color, size, friability, and disintegration time, as well as microorganism content during the 12-month preservation. With simple, easy and reliable technique and quality control method, the process study had obtained the national patent process （patent number： ZL200810233796.X）, and the contents of heavy metals and micr6organisms laid foundation for the quality standard.

Study on Effects of Different Factors to Eggs Hatching Rate of Cryptotympana atrata by Orthogonal Design

[Objective] The paper aimed to explore influence of different factors on eggs hatching of Cryptotympana atrata,and optimize technical parameters in practice.[Method] By using hatching rate as index,L16（44）orthogonal design was employed to determine the effects of the four factors including temperature,salinity,photoperiod and pH.[Result] Photoperiod had obviously effects on hatchability of Cryptotympana atrata eggs.The optimal conditions for hatching were temperature 30 ℃,salinity 25%,photoperiod L12∶D12,and pH 6.[Conclusion]The research provided some scientific basis for indoor artificial incubation.

Storage stability of SBS modified bitumen based on mixed-level orthogonal array design

The styrene-butadiene-styrene（SBS） modified bitumens with different contents of SBS modifiers are stored in different conditions to study the storage stability of SBS modified bitumen.Mixed-level orthogonal array design（OAD） is used and factors such as SBS modifier content,storage time,storage temperature and container size are chosen in a mixed-level OAD with an OA16（31×44） matrix.Parameters like the separation softening point difference（the separation difference of the ring and ball softening point of the top and bottom samples） and the average softening point（the arithmetic mean of the softening points of the top and bottom samples） are proposed to evaluate the separation and the ageing of modified bitumen during storage in this experiment,respectively.The results reveal that the separation and the ageing during storage exhibit a complicated variation for storage temperature and time.The separation softening point difference decreases with the storage temperature rising from 20 to 120 ℃ and increases with the temperature exceeding 120 ℃,and the average softening point drops with the storage time being prolonged.Different storage conditions have various effects on the storage stability of SBS modified bitumen.

A New Generalized Complex Orthogonal Space-Time Block Codes

Recent research challenges in the wireless communication include the usage of diversity and efficient coding to improve data transmission quality and spectral efficiency. Space diversity uses multiple transmitting and/or receiving antennas to create independent fading channels without penalty in bandwidth efficiency. Space-time block coding is an encoding scheme for communication over Rayleigh fading channels using multiple transmitting antennas. Space-time block codes from complex orthogonal designs exist only for two transmitting antennas. This paper generalizes a new complex orthogonal space-time block code for four transmitting antennas, whose decoding complexity is very low. Simulations show that the generalized complex orthogonal space-time block code has low bit error rate, full rate and possibly large diversity.

Optimization of RAPD-PCR Reaction System for Glycyrrhiza uralensis Based on Orthogonal Design

[Objective] The aim was to obtain the optimum RAPD-PCR reaction system for Glycyrrhiza uralensis.[Method] Orthogonal design was adopted to screen the suitable concentration of four major factors（dNTPs,primers,Taq polymerase and DNA template） in PCR reaction system.[Result] The optimal reaction system obtained by orthogonal design was 25 μl in total volume,containing 2.5 μl of 10×PCR buffer solution（include MgCl2）,2.5 μl of 10 mmol/L dNTPs,2 μl（100 ng） of DNA template,2 μl of 10 μmol/L primers,0.4 μl（5 U） of Taq polymerase;the optimum annealing temperature was 34 ℃.[Conclusion] Orthogonal design was an effective method for the optimization of RAPD-PCR reaction system for G.uralensis.

Study on Rapid Propagation Medium of Atractylodes Lances by Orthogonal Design

[Objective] The aim was to protect wild resource of Atractylodes lances and to provide technical guidance for industrialization of Atractylodes lances. [Method] The test-tube seedlings were produced from seeds of Atractylodis Lances. At the same time, the effects of 6-BA, NAA and KT on the proliferation of aseptic seedling was studied through the orthogonal test. Effect of NAA concentration on the rooting of aseptic seedling was studied through nine types of light substrate groups, which consist of peat soil, fine sand and cotton seed hull, and their effects on Atractylodes lances growth were studied on with orthogonal design. [Result] The culture medium suitable for the proliferation of the Atractylodes lances tube seedling was MS＋6-BA 1.0 mg/L＋NAA 0.4 mg/L＋KT 0,4 mg/L. And the medium suitable for rooting was 1/2MS＋NAA 0.5 mg/L. The optimal ratio of soil, riversand and cotton seed hull was 3：3：2. [Conclusion] The research selected optimum culture medium, rooting medium and ratio of substrate, which provided technical guidance for laboratorial preservation of germplasm resource of Atractylodes lances and industrialization of its seedling production.

Orthogonal design to sift the optimal parameter of Neiguan acupuncture for cerebral infarction

The individual difference and non-repeatability in acupuncture have not only restricted the devel- opment of acupuncture, but have also affected the specificity of acupoints. The present study used instruments to control needle depth, lifting and thrusting frequency, and the duration of acupuncture. Effects of the quantified acupuncture were observed at Neiguan （PC6） with different stimulation parameters. A frequency of 1, 2, or 3 Hz and duration of 5, 60, or 180 seconds were used to observe cerebral blood flow and ratio of infarct volume recovery. Results showed that stimulation at Neiguan with a frequency of 1 Hz and long duration of 180 seconds or 2/3 Hz and long duration of 5/60 seconds significantly increased cerebral blood flow and decreased the ratio of infarct volume. In- teractions between frequency and duration play a critical role in quantified acupuncture therapy.

Orthogonal design and numerical simulation of room and pillar configurations in fractured stopes

Room and pillar sizes are key factors for safe mining and ore recovery in open-stope mining. To investigate the influence of room and pillar configurations on stope stability in highly fractured and weakened areas, an orthogonal design with two factors, three levels and nine runs was proposed, followed by three-dimensional numerical simulation using ANSYS and FLAC3~. Results show that surface settlement after excavation is concentrically ringed, and increases with the decrease of pillar width and distances to stope gobs. In the meantime, the ore-control fault at the ore-rock boundary and the fractured argillaceous dolomite with intercalated slate at the hanging wall deteriorate the roof settlement. Additionally, stope stability is challenged due to pillar rheological yield and stress concentration, and both are induced by redistribution of stress and plastic zones after mining. Following an objective function and a constraint function, room and pillar configuration with widths of 14 m and 16 m, respectively, is presented as the optimization for improving the ore recovery rate while maintaining a safe working environment.

Orthogonal design for optimization of pigment extraction from surface sediments of the Changjiang River Estuary

Using a suitable solvent for extracting pigments from sediment for high performance liquid chromatography（HPLC） analysis is critical for obtaining qualitative and quantitative estimates of phytoplanktonic and benthic algal biomass,as well as community composition. Five methodological factors（sample dehydration,extraction solvent,extraction duration,number of extractions,and ratio of solvent volume：sample weight） were studied using an L 9（3 4 ） orthogonal design in a sedimentary pigment extraction experiment on samples collected from the Changjiang large-river delta-front estuary（LDE）,using HPLC analysis. The results show that the optimal extraction method for sedimentary pigments should include freeze-drying samples prior to extraction. The effects of different factors on sedimentary pigment extraction were separated by the L 9（3 4 ） orthogonal design experiments and showed that the extraction solvent was the most important,with extraction duration the second most important,and numbers of extraction and ratio of solvent volume：sample weight was the least important. The mixed solvent treatment comprised of acetone,methanol and water（80：15：5,by volume） was best for polar pigment extraction,with 100% acetone better for apolar pigments. For most pigments employed in this study（i.e.,peridinin,fucoxanthin,alloxanthin,diatoxanthin,zeaxanthin,pheophytin-a and β-carotene） ,3 h was found to be enough time for extraction from these deltaic sediments. However,for chlorophyll-a,the most important pigment used for estimating algal biomass,12 h was needed. A small amount of solvent（3 ml） with duplicate extractions obtained the greatest amount and diversity of pigments. Unfortunately,no extraction method was found to be suitable for all pigments in sediments. The choice of extraction procedure should be made in accordance with the objective of each study,taking into consideration the properties of sediments and pigments in question.

Cavitation Optimization for a Centrifugal Pump Impeller by Using Orthogonal Design of Experiment

Cavitation is one of the most important performance of centrifugal pumps. However, the current optimization works of centrifugal pump are mostly focusing on hydraulic efficiency only, which may result in poor cavitation performance. Therefore, it is necessary to find an appropriate solution to improve cavitation performance with acceptable efficiency. In this paper, to improve the cavitation performance of a centrifugal pump with a vaned diffuser, the influence of impeller geometric parameters on the cavitation of the pump is investigated using the orthogonal design of experiment （DOE） based on computational fluid dynamics. The impeller inlet diameter D1, inlet incidence angle Aft, and blade wrap angle ~0 are selected as the main impeller geometric parameters and the orthogonal experiment of L9（3＂3） is performed. Three-dimensional steady simulations for cavitation are conducted by using constant gas mass fraction model with second-order upwind, and the predicated cavitation performance is validated by laboratory experiment. The optimization results are obtained by the range analysis method to improve cavitation performance without obvious decreasing the efficiency of the centrifugal pump. The internal flow of the pump is analyzed in order to identify the flow behavior that can affect cavitation performance. The results show that D1 has the greatest influence on the pump cavitation and the final optimized impeller provides better flow distribution at blade leading edge. The final optimized impeller accomplishes better cavitation and hydraulic performance and the NPSHR decreases by 0.63m compared with the original one. The presented work supplies a feasible route in engineering practice to optimize a centrifugal pump impeller for better cavitation performance.

Optimizing SSR-PCR system of Panax ginseng by orthogonal design

An orthogonal design was used to optimize SSR-PCR amplification system using Panax ginseng genomic DNA as template. Four levels of five factors （DNA template, Taq DNA polymerase, Mg^2＋, primer, and dNTP） and annealing temperature have been tested separately in this system. The results demonstrated the reaction efficiency was affected by these factors. Based on the results, a stable, productive and reproducible PCR system and cycling program for amplifying a ginseng SSR locus were obtained： 20 μL system containing 1.0 U Taq DNA polymerase, 2.0 mmol·L^-1 Mg^2＋, 0.2 mmol·L^-1 dNTPs, 0.3 μmol·L^-1 SSR primer, 60 ng· μla^-1 DNA template, performed with a program of 94℃ for 5 min, 94℃ for 30 s, annealing at 56.3℃ for 30 s, 72℃ for 1 min, 37 cycles, finishing at 72℃ for 7 min, and storing at 4℃.

Influence of plasma-MIG welding parameters on aluminum weld porosity by orthogonal test

The plasma-MIG welding torch was developed.5A06 aluminum alloys with V-grooves were welded in a single pass in the plasma-MIG welding process and the joints were examined by X-ray diffractometry analysis and mechanical tests.The orthogonal experimental design was used to study the influence of plasma-MIG welding parameters on the aluminum weld porosity.The mixed orthogonal matrix L16(4 4×2 3) and analysis of variance (ANOVA)technique were employed to optimize the welding parameters.The experimental results indicate that the effect of plasma gas flow rate is dominant,the secondary factors are MIG welding voltage,welding speed,wire feed rate and plasma current in turn.Confirmation experiments were conducted under optimum conditions and there was almost no porosity in the welded joints,thus good mechanical performance joints were obtained.

Solution for integer linear bilevel programming problems using orthogonal genetic algorithm

An integer linear bilevel programming problem is firstly transformed into a binary linear bilevel programming problem, and then converted into a single-level binary implicit programming. An orthogonal genetic algorithm is developed for solving the binary linear implicit programming problem based on the orthogonal design. The orthogonal design with the factor analysis, an experimental design method is applied to the genetic algorithm to make the algorithm more robust, statistical y sound and quickly convergent. A crossover operator formed by the orthogonal array and the factor analysis is presented. First, this crossover operator can generate a smal but representative sample of points as offspring. After al of the better genes of these offspring are selected, a best combination among these offspring is then generated. The simulation results show the effectiveness of the proposed algorithm.

Orthogonal experiment design of EMI of security monitoring system in coal mines

Security monitoring system of coal mines is indispensable to ensure the safe and efficient production of colliery. Due to the special and narrow underground field of the coal mine, the electromagnetic interference can cause a series of misstatements and false positives on the monitoring system, which will severely hamper the safe production of coal industry. In this paper, first, the frequency characteristics of the interference source on the power line are extracted when equipment runs normally. Then the finite difference time domain method is introduced to analyze the effects of the electromagnetic interference parameters on the security monitoring signal line. And the interference voltage of the two terminal sides on the single line is taken as evaluating indexes. Finally, the electromagnetic interference parameters are optimized by orthogonal experimental design based on the MATLAB simulation on the normal operation of equipment.

Application of orthogonal experimental design and Tikhonov regularization method for the identification of parameters in the casting solidification process

The inverse heat conduction method is one of methods to identify the casting simulation parameters. A new inverse method was presented according to the Tikhonov regularization theory. One appropriate regularized functional was established, and the functional was solved by the sensitivity coefficient and Newtonaphson iteration method. Moreover, the orthogonal experimental design was used to estimate the appropriate initial value and variation domain of each variable to decrease the number of iteration and improve the identification accuracy and efficiency. It illustrated a detailed case of AlSiTMg sand mold casting and the temperature measurement experiment was done. The physical properties of sand mold and the interracial heat transfer coefficient were identified at the meantime. The results indicated that the new regularization method was efficient in overcoming the ill-posedness of the inverse heat conduction problem and improving the stability and accuracy of the solutions.

Oil Tea Soup Formula Optimization Based on Orthogonal Test and Fuzzy Mathematics Sensory Evaluation

The aim of this study is to optimize the formula of oil soup, which was one of traditional food of Guangxi province, south China. Tea leaves, bone soup, beans and other minor ingredients in the formula of oil tea soup are selected as the research objects. The sensory evaluation factors such as flavor, taste, color, aroma were selected to optimize the formula of oil tea soup based on orthogonal test and fuzzy mathematics comprehensive evaluation. The results showed the most important factor that affected the quality of the oil tea soup was tea leaves content, followed by the proportion of bone soup, minor ingredient and beans content. The study indicated that the optimal recipe ofoil tea soup was as follow： 0.6% tea, 0.4% beans, and 0.5% other ingredients. The ratio of material to solution of bone soup was 1：5.