Summary of Useful Concepts About the Coordination of Directional Overcurrent Protections

This paper summarizes some useful concepts about the coordination of directional overcurrent protections.The following key topics are described:the analysis of systems in a ring configuration and only one source of short-circuit currents;the impossibility of obtaining selectivity for all the possible system configurations with multiple sources;the need for inverse functions in order to obtain selectivity in systems with multiple sources;the coordination with protections for radial loads;the coordination between instantaneous and delayed functions;the considerations to select the pickup values;the influence of contributions from motors to short circuit currents;the transient configurations due to sequential trips at both line ends;the influence of dynamic behavior of overcurrent functions;the influence of stability constraints;other specific considerations for ground functions;some specific considerations for systems with distributed generation.A summary of these points and their effect on the coordination of directional overcurrent protections is not available in the current literature.This novel description should facilitate the inclusion of these key points in research and coordination studies related to these protective functions.

Simulation Studies of an Integrated Overcurrent Relay Protection Scheme for Distribution Systems

This paper presents an integrated protection technique for power distribution systems. A novel integrated protection scheme based on overcurrent protection technique for distribution system is described, in which a specially designed protection relay is installed at each substation of a network and responsible for the protection of every line sections connected to the substation busbar The conventional directional overcurrent and the new adaptive accelerated protection algorithms with multiple settings are implemented into the relay to cover all the protected line sections. The paper includes studies of a typical multi section distribution network to demonstrate the principle of the scheme. Studies show that the new scheme not only offer the new protection features for individual power line section, but also provide the characteristics of integrated protection.

Preparation and Properties of PTC Material with Low Resistivity

The demand for PTC material for overcurrent protection application in automobile motors has been remarkably increasing. To meet the safety and reliability requirements in automobile system and communication equipment, it is necessary to prepare PTC material with low resistivity and high performance. In this paper, the preparation and the properties of PTC material with a resistivity of approximately 12Ω. cm, especially its overcurrent protection are described.

IEC61850 standard-based harmonic blocking scheme for power transformers

Transformer Differential and overcurrent schemes are traditionally used as main and backup protection respectively. The differential protection relay (SEL487E) has dedicated harmonic restraint function which blocks the relay tripping during the transformer magnetizing inrush conditions. However, the backup overcurrent relay (SEL751A) applied to the transformer protection does not have harmonic restraint element and trip the overcurrent relay during the inrush conditions. Therefore, major contribution of this research work is the developed harmonic blocking scheme for transformer which uses element (87HB) of the transformer differential relay (SEL487E) to send an IEC61850 GOOSE-based harmonic blocking signal to the backup overcurrent relay (SEL751A) to inhibit from tripping during the transformer magnetizing inrush current conditions. The simulation results proved that IEC61850 standard-based protection scheme is faster than the hardwired signals. Therefore, the speed and reliability of the transformer scheme are improved using the IEC61850 standard-based GOOSE applications.

Transient stability enhancement of DC-connected DFIG and its converter system using fault protective device

Transient stability of doubly-fed induction generators(DFIGs)is a major concern in both AC and DC grids,and DFIGs must stay connected for a time during grid faults according to the power grid requirements.For this purpose,this work proposes an overcurrent and overvoltage protective device(OCV-PD)to ensure that DCbased DFIG system can stay connected and operate well during the faults.Compared with a series dynamic braking resistor(SDBR),two aspects are improved.First,a twolevel control strategy and DC inductor circuit are used to ensure that the OCV-PD can limit the current impulse to protect DFIG system during an overcurrent fault.Second,the OCV-PD can protect system from overvoltage fault which a SDBR cannot do.Simulation results verify itsvalidity and feasibility,finding that for overcurrent protection the OCV-PD outperforms a SDBR with an average decreased index of 3.29%,and for overvoltage protection it achieves an average index of 1.02%.