Method for determining the position of landslide slip-surface with a typical inclinometric curves

In the actual monitoring of deep hole displacement,the identification of slip surfaces is primarily based on abrupt changes observed in the inclinometric curve.In conventional identification methods,inclinometric curves exhibiting indications of sliding can be categorized into three types:B-type,D-type,and r-type.The position of the slip surface is typically determined by identifying the depth corresponding to the point of maximum displacement mutation.However,this method is sensitive to the interval of measurement points and the observation scale of the coordinate axes and suffers from unclear sliding surfaces and uncertain values.Based on the variation characteristics of these diagonal curves,we classified the landslide into three components:the sliding body,the sliding interval,and the immobile body.Moreover,three different generalization models were established to analyze the relationships between the curve form and the slip surface location based on different physical indicators such as displacement rate,relative displacement,and acceleration.The results show that the displacement rate curves of an r-type slope exhibit a clustering feature in the sliding interval,and by solving for the depth of discrete points within the step phase,it is possible to determine the location of the slip surface.On the other hand,D-type slopes have inflection points in the relative displacement curve located at the slip surface.The acceleration curves of B-type slopes exhibit clustering characteristics during the sliding interval,while the scattered acceleration data demonstrate wandering characteristics.Consequently,the slip surface location can be revealed by solving the depth corresponding to the maximum acceleration with cubic spline interpolation.The approach proposed in this paper was applied to the monitoring data of a landslide in Yunnan Province,China.The results indicate that our approach can accurately identify the slip surface location and enable computability of its position,thereby enhancing applicability and reliability of the deep-hole displacement monitoring data.

A comparative study of data-driven battery capacity estimation based on partial charging curves

With its generality and practicality, the combination of partial charging curves and machine learning(ML) for battery capacity estimation has attracted widespread attention. However, a clear classification,fair comparison, and performance rationalization of these methods are lacking, due to the scattered existing studies. To address these issues, we develop 20 capacity estimation methods from three perspectives:charging sequence construction, input forms, and ML models. 22,582 charging curves are generated from 44 cells with different battery chemistry and operating conditions to validate the performance. Through comprehensive and unbiased comparison, the long short-term memory(LSTM) based neural network exhibits the best accuracy and robustness. Across all 6503 tested samples, the mean absolute percentage error(MAPE) for capacity estimation using LSTM is 0.61%, with a maximum error of only 3.94%. Even with the addition of 3 m V voltage noise or the extension of sampling intervals to 60 s, the average MAPE remains below 2%. Furthermore, the charging sequences are provided with physical explanations related to battery degradation to enhance confidence in their application. Recommendations for using other competitive methods are also presented. This work provides valuable insights and guidance for estimating battery capacity based on partial charging curves.

Analytical Determination of Size and Location of Roadside Horizontal Sightline Offsets for Compound Curves

AASHTO’s guideline for geometric design of highways and similar guidelines require that roadside areas on the inside of horizontal curves be cleared of high objects to provide stopping sight distance. The guidelines have analytical models for determining the extent of clearance, known as the horizontal sightline offset or clearance offset, for simple curves. Researchers in the past have developed analytical models for clearance offsets for spiraled and reverse curves. Very few researchers developed analytical models for available sight distances for compound curves. Still missing are models for horizontal sightline offsets and locations of the offsets for compound curves. The objective of this paper is to present development of analytical models and charts for determining horizontal sightline offsets and their locations for compound curves. The paper considers curves whose component arcs are individually shorter than stopping sight distance. The resulting models and the charts have been verified with accurate values determined using graphical methods. The models and the charts will find application in geometric design of highway compound curves.

Using Pearson’s System of Curves to Approximate the Distributions of the Difference between Two Correlated Estimates of Signal-to-Noise Ratios: The Cases of Bivariate Normal and Bivariate Lognormal Distributions

Background: The signal-to-noise ratio (SNR) is recognized as an index of measurements reproducibility. We derive the maximum likelihood estimators of SNR and discuss confidence interval construction on the difference between two correlated SNRs when the readings are from bivariate normal and bivariate lognormal distribution. We use the Pearsons system of curves to approximate the difference between the two estimates and use the bootstrap methods to validate the approximate distributions of the statistic of interest. Methods: The paper uses the delta method to find the first four central moments, and hence the skewness and kurtosis which are important in the determination of the parameters of the Pearsons distribution. Results: The approach is illustrated in two examples;one from veterinary microbiology and food safety data and the other on data from clinical medicine. We derived the four central moments of the target statistics, together with the bootstrap method to evaluate the parameters of Pearsons distribution. The fitted Pearsons curves of Types I and II were recommended based on the available data. The R-codes are also provided to be readily used by the readers.

Sensitive Information Security Based on Elliptic Curves

The elliptic curve cryptography algorithm represents a major advancement in the field of computer security. This innovative algorithm uses elliptic curves to encrypt and secure data, providing an exceptional level of security while optimizing the efficiency of computer resources. This study focuses on how elliptic curves cryptography helps to protect sensitive data. Text is encrypted using the elliptic curve technique because it provides great security with a smaller key on devices with limited resources, such as mobile phones. The elliptic curves cryptography of this study is better than using a 256-bit RSA key. To achieve equivalent protection by using the elliptic curves cryptography, several Python libraries such as cryptography, pycryptodome, pyQt5, secp256k1, etc. were used. These technologies are used to develop a software based on elliptic curves. If built, the software helps to encrypt and decrypt data such as a text messages and it offers the authentication for the communication.

Review on Service Curves of Typical Scheduling Algorithms

In recent years,various internet architectures,such as Integrated Services(IntServ),Differentiated Services(DiffServ),Time Sensitive Networking(TSN)and Deterministic Networking(DetNet),have been proposed to meet the quality-of-service(QoS)requirements of different network services.Concurrently,network calculus has found widespread application in network modeling and QoS analysis.Network calculus abstracts the details of how nodes or networks process data packets using the concept of service curves.This paper summarizes the service curves for typical scheduling algorithms,including Strict Priority(SP),Round Robin(RR),Cycling Queuing and Forwarding(CQF),Time Aware Shaper(TAS),Credit Based Shaper(CBS),and Asynchronous Traffic Shaper(ATS).It introduces the theory of network calculus and then provides an overview of various scheduling algorithms and their associated service curves.The delay bound analysis for different scheduling algorithms in specific scenarios is also conducted for more insights.

The Effectiveness of the Havriliak-Negami Model in Predicting the Master Curves of the Asphalt Blends with SBS Triblock Copolymer and Organic-Montmorillonite at Different Temperatures and Frequencies

The dynamic viscoelastic properties of asphalt AC-20 and its composites with Organic-Montmorillonite clay (OMMt) and SBS were modeled using the empirical Havriliak-Negami (HN) model, based on linear viscoelastic theory (LVE). The HN parameters, α, β, G0, G∞and τHN were determined by solving the HN equation across various temperatures and frequencies. The HN model successfully predicted the rheological behavior of the asphalt and its blends within the temperature range of 25˚C - 40˚C. However, deviations occurred between 40˚C - 75˚C, where the glass transition temperature Tg of the asphalt components and the SBS polymer are located, rendering the HN model ineffective for predicting the dynamic viscoelastic properties of composites containing OMMt under these conditions. Yet, the prediction error of the HN model dropped to 2.28% - 2.81% for asphalt and its mixtures at 100˚C, a temperature exceeding the Tg values of both polymer and asphalt, where the mixtures exhibited a liquid-like behavior. The exponent α and the relaxation time increased with temperature across all systems. Incorporating OMMt clay into the asphalt blends significantly enhanced the relaxation dynamics of the resulting composites.

Magnetic Field Curves and Magnetic Equipotential Surfaces around Crossing Electrical Wires Replacing Classical Magnetic Field Lines

This article is based on a recent model specifically defining magnetic field values around electrical wires. With this model, calculations of field around parallel wires were obtained. Now, this model is extended with the new concept of magnetic equipotential surface to magnetic field curves around crossing wires. Cases of single, double, and triple wires are described. Subsequent article will be conducted for more general scenarios where wires are neither infinite nor parallel.

The Origin of the Flat Rotation Curves in Spiral Galaxies: The Hidden Roles of Glitching SMDEOs and Emission of Gravitational Waves

Supermassive DEOs (SMDEOs) are cosmologically evolved objects made of irreducible incompressible supranuclear dense superfluids: The state we consider to govern the matter inside the cores of massive neutron stars. These cores are practically trapped in false vacua, rendering their detection by outside observers impossible. Based on massive parallel computations and theoretical investigations, we show that SMDEOs at the centres of spiral galaxies that are surrounded by massive rotating torii of normal matter may serve as powerful sources for gravitational waves carrying away roughly 1042 erg/s. Due to the extensive cooling by GWs, the SMDEO-Torus systems undergo glitching, through which both rotational and gravitational energies are abruptly ejected into the ambient media, during which the topologies of the embedding spacetimes change from curved into flatter ones, thereby triggering a burst gravitational energy of order 1059 erg. Also, the effects of glitches found to alter the force balance of objects in the Lagrangian-L1 region between the central SMDEO-Torus system and the bulge, enforcing the enclosed objects to develop violent motions, that may explain the origin of the rotational curve irregularities observed in the innermost part of spiral galaxies. Our study shows that the generated GWs at the centres of galaxies, which traverse billions of objects during their outward propagations throughout the entire galaxy, lose energy due to repeatedly squeezing and stretching the objects. Here, we find that these interactions may serve as damping processes that give rise to the formation of collective forces f∝m(r)/r, that point outward, endowing the objects with the observed flat rotation curves. Our approach predicts a correlation between the baryonic mass and the rotation velocities in galaxies, which is in line with the Tully-Fisher relation. The here-presented self-consistent approach explains nicely the observed rotation curves without invoking dark matter or modifying Newtonian gravitation in the low-field approximation.

Characterization of the generalized permeability jail in tight reservoirs by analyzing relative-permeability curves and numerical simulation

This study comprehensively characterizes the boundary values of generalized permeability jail in tight reservoirs through relative-permeability curve analysis,numerical simulation,and economic evaluation.A total number of 108 relative-permeability curves of rock samples from tight reservoirs were obtained,and the characteristics of relative-permeability curves were analyzed.The irreducible water saturation(Swi)mainly ranges from 20% to 70%,and the residual gas saturation(Sgr)ranges from 5% to 15% for 55% of the samples.The relative-permeability curves are categorized into six types(Category-Ⅰ to Ⅵ)by analyzing the following characteristics:The relative permeability of gas at Swi,the relative permeability of water at Sgr,and the relative permeability corresponding to the isotonic point.The relative permeability curves were normalized to facilitate numerical simulation and evaluate the impact of different types of curves on production performance.The results of simulation show significant difference in production performance for different types of relative-permeability curves:Category-Ⅰ corresponds to the case with best well performance,whereas Categories-Ⅴ and Ⅵ correspond to the cases with least production volume.The results of economic evaluation show a generalized permeability jail for Categories-Ⅳ,Ⅴ,and Ⅵ,and the permeability jail develops when the relative permeability of gas and water is below 0.06.This study further quantifies the range of micro-pore parameters corresponding to the generalized permeability jail for a tight sandstone reservoir.

Inverse design of mechanical metamaterial achieving a prescribedconstitutive curve

Besides exhibiting excellent capabilities such as energy absorption,phase-transforming metamaterials offer a vast design space for achieving nonlinear constitutive relations.This is facilitated by switching between different patterns under deformation.However,the related inverse design problem is quite challenging,due to the lack of appropriate mathematical formulation and the convergence issue in the post-buckling analysis of intermediate designs.In this work,periodic unit cells are explicitly described by the moving morphable voids method and effectively analyzed by eliminating the degrees of freedom in void regions.Furthermore,by exploring the Pareto frontiers between error and cost,an inverse design formulation is proposed for unit cells.This formulation aims to achieve a prescribed constitutive curve and is validated through numerical examples and experimental results.The design approach presented here can be extended to the inverse design of other types of mechanical metamaterials with prescribed nonlinear effective properties.

基于改进p-有效点法的多风电场共享储能联合参与一次调频的容量优化

以大规模多风电场接入电力系统的一次调频备用容量为研究对象,首先通过引入风电出力预测误差的概率分布描述系统的不确定性因素,考虑风储一次调频备用总成本最小为目标;然后建立基于机会约束规划的多风电场联合共享储能参与一次调频的容量优化模型;最后提出基于快速傅里叶变换快速求解联合变量概率分布的改进p-有效点法通过数学解析将机会约束规划从形式上转化为确定性规划,再通过Yalmip调用Cplex实现模型的快速求解。算例结果表明,所提模型和方法可有效提高风储调频效果和收益,且具有更高的求解效率。

A Novel Contour Tracing Algorithm for Object Shape Reconstruction Using Parametric Curves

Parametric curves such as Bézier and B-splines, originally developedfor the design of automobile bodies, are now also used in image processing andcomputer vision. For example, reconstructing an object shape in an image,including different translations, scales, and orientations, can be performedusing these parametric curves. For this, Bézier and B-spline curves can be generatedusing a point set that belongs to the outer boundary of the object. Theresulting object shape can be used in computer vision fields, such as searchingand segmentation methods and training machine learning algorithms. Theprerequisite for reconstructing the shape with parametric curves is to obtainsequentially the points in the point set. In this study, a novel algorithm hasbeen developed that sequentially obtains the pixel locations constituting theouter boundary of the object. The proposed algorithm, unlike the methods inthe literature, is implemented using a filter containing weights and an outercircle surrounding the object. In a binary format image, the starting point ofthe tracing is determined using the outer circle, and the next tracing movementand the pixel to be labeled as the boundary point is found by the filter weights.Then, control points that define the curve shape are selected by reducing thenumber of sequential points. Thus, the Bézier and B-spline curve equationsdescribing the shape are obtained using these points. In addition, differenttranslations, scales, and rotations of the object shape are easily provided bychanging the positions of the control points. It has also been shown that themissing part of the object can be completed thanks to the parametric curves.

亚油酸诱导植物乳杆菌p-8产生共轭亚油酸的蛋白组和类组蛋白乙酰化分析

研究亚油酸(linoleic acid,LA)诱导下植物乳杆菌(Lactobacillus plantarum)p-8的蛋白组和类组蛋白乙酰化水平差异,探究共轭亚油酸(conjugated linoleic acid,CLA)产生的机制。结果表明,LA的最佳诱导质量浓度为1 mg/mL,在此质量浓度条件下,蛋白质组学分析发现,烯酰-酰基载体蛋白还原酶、酰基载体蛋白等脂肪酸合成的关键蛋白因子下调,脂肪酸合成下调,乙酰基转移酶水平上调。Western blot结合体外添加NaAc实验表明,乙酰辅酶A含量增加导致类组蛋白乙酰化水平提升。实时聚合酶链式反应检测显示,添加LA和NaAc使CLA相关酶、转录调控因子和Sigma因子的mRNA表达升高,CLA含量也提高。相关性分析得出,乙酰辅酶A与LA水合酶转录水平和CLA含量之间呈显著正相关,揭示乙酰辅酶A和乙酰基转移酶含量上调导致类组蛋白乙酰化加强而上调CLA合成。结果为分子改良或科学调控乳酸菌以提高CLA转化率奠定了基础。

具p-双调和算子的非局部椭圆方程Navier边值问题的广义解

利用变分方法和相应的临界点定理研究一类具有p-双调和算子的非局部椭圆方程Navier边值问题,在非线性项满足超线性条件时,得到了两个非平凡广义解的存在性定理.

健脾化瘀解毒法对结肠癌裸鼠模型癌及癌旁组织中AKT、mTOR、p-4EBP1表达的影响研究

目的研究健脾化瘀解毒法对结肠癌原位种植瘤癌及癌旁组织中蛋白激酶B(AKT)、哺乳动物雷帕霉素靶蛋白(mTOR)、磷酸化真核细胞起始因子4E结合蛋白1(p-4EBP1)表达的影响。方法建立裸鼠结肠癌模型,随机分为空白组、模型组、健脾益气组、化瘀解毒组、健脾化瘀解毒组、雷帕霉素组及5-氟尿嘧啶组,每组5只。干预各组4周后,检测各组癌组织与癌旁组织中AKT、mTOR、p-4EBP1的表达水平。结果与空白组比较,模型组癌组织与癌旁组织中AKT1、mTOR、p-4EBP1的表达均上调,差异有显著性(P<0.05),且AKT、mTOR、p-4EBP1的表达水平均为癌组织>癌旁组织>正常肠黏膜组织。与模型组比较,健脾化瘀解毒法能在一定程度上抑制结肠癌癌组织及癌旁组织中AKT、mTOR、p-4EBP1的表达水平,差异有统计学意义(P<0.05);健脾益气法、化瘀解毒法均能下调癌组织与癌旁组织中AKT、mTOR、p-4EBP1蛋白,但其降低水平不如健脾化瘀解毒法。结论健脾化瘀解毒法能够降低AKT、mTOR、p-4EBP1蛋白的表达,健脾益气法与化瘀解毒法协同增效,以获得最佳疗效。

Experimental p-y curves for liquefied soils from centrifuge tests

The present study aims to obtain p-y curves(Winkler spring properties for lateral pile-soil interaction)for liquefied soil from 12 comprehensive centrifuge test cases where pile groups were embedded in liquefiable soil.The p-y curve for fully liquefied soil is back-calculated from the dynamic centrifuge test data using a numerical procedure from the recorded soil response and strain records from the instrumented pile.The p-y curves were obtained for two ground conditions:(a)lateral spreading of liquefied soil,and(b)liquefied soil in level ground.These ground conditions are simulated in the model by having collapsing and non-collapsing intermittent boundaries,which are modelled as quay walls.The p-y curves back-calculated from the centrifuge tests are compared with representative reduced API p-y curves for liquefied soils(known as p-multiplier).The response of p-y curves at full liquefaction is presented and critical observations of lateral pile-soil interaction are discussed.Based on the results of these model tests,guidance for the construction of p-y curves for use in engineering practice is also provided.

Investigation of magnetization reversal and domain structures in perpendicular synthetic antiferromagnets by first-order reversal curves and magneto-optical Kerr effect

Perpendicular synthetic-antiferromagnet(p-SAF) has broad applications in spin-transfer-torque magnetic random access memory and magnetic sensors. In this study, the p-SAF films consisting of (Co/Ni)3]/Ir(tIr)/[(Ni/Co)3are fabricated by magnetron sputtering technology. We study the domain structure and switching field distribution in p-SAF by changing the thickness of the infrared space layer. The strongest exchange coupling field(Hex) is observed when the thickness of Ir layer(tIr) is 0.7 nm and becoming weak according to the Ruderman–Kittel–Kasuya–Yosida-type coupling at 1.05 nm,2.1 nm, 4.55 nm, and 4.9 nm in sequence. Furthermore, the domain switching process between the upper Co/Ni stack and the bottom Co/Ni stack is different because of the antiferromagnet coupling. Compared with ferromagnet coupling films, the antiferromagnet samples possess three irreversible reversal regions in the first-order reversal curve distribution.With tIrincreasing, these irreversible reversal regions become denser and smaller. The results from this study will help us understand the details of the magnetization reversal process in the p-SAF.

Quality influencing factors of dispersion curves from short period dense arrays based on a convolutional neural network across the north section of the Xiaojiang fault area

The number of dispersion curves increases significantly when the scale of a short-period dense array increases.Owing to a substantial increase in data volume,it is important to quickly evaluate dispersion curve quality as well as select the available dispersion curve.Accordingly,this study quantitatively evaluated dispersion curve quality by training a convolutional neural network model for ambient noise tomography using a short-period dense array.The model can select high-quality dispersion curves that exhibit a≤10%difference between the results of manual screening and the proposed model.In addition,this study established a dispersion curve loss function by analyzing the quality of the dispersion curve and the corresponding influencing factors,thereby estimating the number of available dispersion curves for the existing observation systems.Furthermore,a Monte Carlo simulation experiment is used to illustrates the station-pair interval distance probability density function,which is independent of station number in the observational system with randomly deployed stations.The results suggested that the straight-line length should exceed 15 km to ensure that loss rate of dispersion curves remains<0.5,while maintaining the threshold ambient noise tomography accuracy within the study area.

Dynamic p-y curves for vertical and batter pile groups in liquefied sand

In this study,centrifuge model tests of vertical and batter pile groups in liquefied sand were conducted on a centrifuge shaking table.The dynamic p-y curves for these pile groups before and during sand liquefaction were obtained from calculations based on test data.The results confirm that liquefaction contributes to a reduction in the energy consumption of pile foundations,with the degradation effect being more pronounced for batter pile groups.At shallow depths,the difference in the backbone gradients of the p-y curves after liquefaction for vertical and batter pile groups indicates that the lateral stiffness of a batter pile group is greater than that of a vertical pile group.As shaking intensity increases,the lateral stiffness of a vertical pile group increases with depth during the late stage of sand liquefaction.However,the lateral stiffness of a batter pile group during liquefaction does not vary with depth.The results of this study provide a reference for the seismic design of vertical and batter pile groups in liquefied soil.