High energy density and low cost made lithium–sulfur(Li–S)batteries appealing for the next-generation energy storage devices.However,their commercial viability is seriously challenged by serious polysulfide shuttle ...High energy density and low cost made lithium–sulfur(Li–S)batteries appealing for the next-generation energy storage devices.However,their commercial viability is seriously challenged by serious polysulfide shuttle effect,sluggish sulfur kinetics,and uncontrollable dendritic Li growth.Herein,a dual-functional electrolyte additive,diphenyl ditelluride(DPDTe)is reported for Li–S battery.For sulfur cathodes,DPDTe works as a redox mediator to accelerate redox kinetics of sulfur,in which Te radical-mediated catalytic cycle at the solid–liquid interface contributes significantly to the whole process.For lithium anodes,DPDTe can react with lithium metal to form a smooth and stable organic–inorganic hybrid solid-electrolyte interphase(SEI),enabling homogeneous lithium deposition for suppressing dendrite growth.Consequently,the Li–S battery with DPDTe exhibits remarkable cycling stability and superb rate capability,with a high capacity up to 1227.3 mAh g^(-1)and stable cycling over 300 cycles.Moreover,a Li–S pouch cell with DPDTe is evaluated as the proof of concept.This work demonstrates that organotelluride compounds can be used as functional electrolyte additives and offers new insights and opportunities for practical Li–S batteries.展开更多
针对2013年1月23日辽宁灯塔M_(S)5.1地震,利用引潮力附加构造应力(Additional Tectonic Stress Caused By Tidal Force,ATSCTF)计算模型,计算得到震中位置(41.5°N,123.2°E)在地震前5周以及震后3周(2012年12月16日—2013年2月1...针对2013年1月23日辽宁灯塔M_(S)5.1地震,利用引潮力附加构造应力(Additional Tectonic Stress Caused By Tidal Force,ATSCTF)计算模型,计算得到震中位置(41.5°N,123.2°E)在地震前5周以及震后3周(2012年12月16日—2013年2月15日)的ATSCTF变化。地震发生时,ATSCTF垂直方向分量处于高相位点附近,显示引潮力对本次正断层走滑型地震具有诱发作用。以ATSCTF变化周期的各低相位点时间(2012年12月19日、2013年1月4日、2013年1月18日、2013年2月2日)数据分别为背景,各周期期后数据分别与背景逐日相减,计算研究区(36°N~46°N,118°E~128°E)范围内,National Oceanic and Atmospheric Administration(NOAA)卫星射出长波辐射数据(Outgoing Long Wave Radiation,OLR)在各ATSCTF周期时段分布及其变化。结果显示,无震的ATSCTF变化的A、B、D周期,震中附近OLR无变化;发震的ATSCTF变化的C周期,在空间上,该地区震前OLR仅震中及其南侧区域发生了显著连续升高变化过程,在时间上经历了初始微异常→异常加强→高峰→衰减→发震→平静的演化过程,与岩石应力加载—破裂经历:初始微动破裂→扩张破裂→应力闭锁→地震爆发→平静的力学演化过程中各阶段红外辐射特征一致;显示引潮力对处于临界状态的活动断层具有诱发作用,而OLR是地震构造应力应变过程辐射表征。展开更多
Chloro-propylene sulfite （CIPS） was employed as electrolyte additive of Li/S batteries for the first time. Linear potential sweep test showed that the CIPS keeps high electrochemical stability even under the voltage...Chloro-propylene sulfite （CIPS） was employed as electrolyte additive of Li/S batteries for the first time. Linear potential sweep test showed that the CIPS keeps high electrochemical stability even under the voltage of 5.0V. Being used as electrolyte additive in Li/S batteries, CIPS displayed an excellent property for self-discharge prohibition. With CIPS additive the Li/S cells initial discharge capacity was 856.2 mAh·g^-1 and 830.8 mAh·g^-1 at the current density of 15 mA.g and 30 mA·g^-1 , after 30 cycles the discharge capacities were contained at as high as 753.8 mAh.g and 715.6 mAh·g^-1. By means of infrared spectra, TG/DTA experiment and element conten analysis the speculated reason of CIPS＇s novel function as additive was proposed.展开更多
The research project'Development and application of FCC additive for maximization of propylene and isobutylene'jointly undertaken by RIPP,the Baling Petrochemical Company(BPC)and the SINOPEC
Additive manufacturing (AM), while enabling the production of parts with complex geometries, presents new challenges. In particular, the achievement of the basic mechanical properties of the alloy must be ensured. In ...Additive manufacturing (AM), while enabling the production of parts with complex geometries, presents new challenges. In particular, the achievement of the basic mechanical properties of the alloy must be ensured. In general, the strength-ductility properties of metals depend strongly on their microstructure, and controlling these properties requires paying attention to the alloy composition, processing technique and heat treatments. Austenite 316L stainless steel parts produced by AM demonstrate good ductility and high yield strength—higher than that obtained with annealed 316L. Some preferred orientation of the mechanical properties was found as a function of the laser path, namely, the Young’s modulus varied with respect to the angle between the build direction and the normal to the build direction. In the present study, samples of AM 316L in three orientations relative to the print direction (0˚, 45˚and 90˚) are compared to a forged sample. Mechanical properties, scanning electron microscopy-SEM fractography, energy dispersive X-ray spectroscope-EDS analysis of the fracture and optical cross section images of the samples along the stress tension after the failure are presented.展开更多
研究了顺序资源共享分配系统的建模模型S4PR(Systems of sequential systems with shared resources)网的活性问题.已有的研究成果表明,一个S4PR网在所有信标都满足max,max或max-controlled时能保持活性,但现有的活性条件对信标的限制...研究了顺序资源共享分配系统的建模模型S4PR(Systems of sequential systems with shared resources)网的活性问题.已有的研究成果表明,一个S4PR网在所有信标都满足max,max或max-controlled时能保持活性,但现有的活性条件对信标的限制严格且不适用于某些网系统,本文提出了一类名为max*-controlled的改进型条件,并证明了当一个S4PR网的所有信标都满足max*-controlled条件时,网系统能保持活性.与现有的其他条件相比,新的活性条件更加宽松,为设计更高允许度的死锁预防或者活性保持监控器提供了理论支撑.展开更多
基金supported by the National Natural Sci-ence Foundation of China(Nos.21975087,U1966214)the Certificate of China Postdoctoral Science Foundation Grant(2020M672337).
文摘High energy density and low cost made lithium–sulfur(Li–S)batteries appealing for the next-generation energy storage devices.However,their commercial viability is seriously challenged by serious polysulfide shuttle effect,sluggish sulfur kinetics,and uncontrollable dendritic Li growth.Herein,a dual-functional electrolyte additive,diphenyl ditelluride(DPDTe)is reported for Li–S battery.For sulfur cathodes,DPDTe works as a redox mediator to accelerate redox kinetics of sulfur,in which Te radical-mediated catalytic cycle at the solid–liquid interface contributes significantly to the whole process.For lithium anodes,DPDTe can react with lithium metal to form a smooth and stable organic–inorganic hybrid solid-electrolyte interphase(SEI),enabling homogeneous lithium deposition for suppressing dendrite growth.Consequently,the Li–S battery with DPDTe exhibits remarkable cycling stability and superb rate capability,with a high capacity up to 1227.3 mAh g^(-1)and stable cycling over 300 cycles.Moreover,a Li–S pouch cell with DPDTe is evaluated as the proof of concept.This work demonstrates that organotelluride compounds can be used as functional electrolyte additives and offers new insights and opportunities for practical Li–S batteries.
基金地震数值预测联合实验室开放基金项目(2020LNEF03)APSCO Earthquake Research Project PhaseⅡ:Integrating Satellite and Ground Observations for Earthquake Signatures and Precursors(WX0519502)。
文摘针对2013年1月23日辽宁灯塔M_(S)5.1地震,利用引潮力附加构造应力(Additional Tectonic Stress Caused By Tidal Force,ATSCTF)计算模型,计算得到震中位置(41.5°N,123.2°E)在地震前5周以及震后3周(2012年12月16日—2013年2月15日)的ATSCTF变化。地震发生时,ATSCTF垂直方向分量处于高相位点附近,显示引潮力对本次正断层走滑型地震具有诱发作用。以ATSCTF变化周期的各低相位点时间(2012年12月19日、2013年1月4日、2013年1月18日、2013年2月2日)数据分别为背景,各周期期后数据分别与背景逐日相减,计算研究区(36°N~46°N,118°E~128°E)范围内,National Oceanic and Atmospheric Administration(NOAA)卫星射出长波辐射数据(Outgoing Long Wave Radiation,OLR)在各ATSCTF周期时段分布及其变化。结果显示,无震的ATSCTF变化的A、B、D周期,震中附近OLR无变化;发震的ATSCTF变化的C周期,在空间上,该地区震前OLR仅震中及其南侧区域发生了显著连续升高变化过程,在时间上经历了初始微异常→异常加强→高峰→衰减→发震→平静的演化过程,与岩石应力加载—破裂经历:初始微动破裂→扩张破裂→应力闭锁→地震爆发→平静的力学演化过程中各阶段红外辐射特征一致;显示引潮力对处于临界状态的活动断层具有诱发作用,而OLR是地震构造应力应变过程辐射表征。
文摘Chloro-propylene sulfite （CIPS） was employed as electrolyte additive of Li/S batteries for the first time. Linear potential sweep test showed that the CIPS keeps high electrochemical stability even under the voltage of 5.0V. Being used as electrolyte additive in Li/S batteries, CIPS displayed an excellent property for self-discharge prohibition. With CIPS additive the Li/S cells initial discharge capacity was 856.2 mAh·g^-1 and 830.8 mAh·g^-1 at the current density of 15 mA.g and 30 mA·g^-1 , after 30 cycles the discharge capacities were contained at as high as 753.8 mAh.g and 715.6 mAh·g^-1. By means of infrared spectra, TG/DTA experiment and element conten analysis the speculated reason of CIPS＇s novel function as additive was proposed.
文摘The research project'Development and application of FCC additive for maximization of propylene and isobutylene'jointly undertaken by RIPP,the Baling Petrochemical Company(BPC)and the SINOPEC
文摘Additive manufacturing (AM), while enabling the production of parts with complex geometries, presents new challenges. In particular, the achievement of the basic mechanical properties of the alloy must be ensured. In general, the strength-ductility properties of metals depend strongly on their microstructure, and controlling these properties requires paying attention to the alloy composition, processing technique and heat treatments. Austenite 316L stainless steel parts produced by AM demonstrate good ductility and high yield strength—higher than that obtained with annealed 316L. Some preferred orientation of the mechanical properties was found as a function of the laser path, namely, the Young’s modulus varied with respect to the angle between the build direction and the normal to the build direction. In the present study, samples of AM 316L in three orientations relative to the print direction (0˚, 45˚and 90˚) are compared to a forged sample. Mechanical properties, scanning electron microscopy-SEM fractography, energy dispersive X-ray spectroscope-EDS analysis of the fracture and optical cross section images of the samples along the stress tension after the failure are presented.
文摘研究了顺序资源共享分配系统的建模模型S4PR(Systems of sequential systems with shared resources)网的活性问题.已有的研究成果表明,一个S4PR网在所有信标都满足max,max或max-controlled时能保持活性,但现有的活性条件对信标的限制严格且不适用于某些网系统,本文提出了一类名为max*-controlled的改进型条件,并证明了当一个S4PR网的所有信标都满足max*-controlled条件时,网系统能保持活性.与现有的其他条件相比,新的活性条件更加宽松,为设计更高允许度的死锁预防或者活性保持监控器提供了理论支撑.
