Catalytic decomposition and mass transfer of aqueous ozone promoted by Fe-Mn-Cu/γ-Al2O_(3) in a rotating packed bed

This study investigated catalytic decomposition and mass transfer of aqueous ozone promoted by Fe-MnCu/γ-Al_(2)O_(3)(Cat)in a rotating packed bed(RPB)for the first time.The results showed that the value of the overall decomposition rate constant of ozone(K_(c))and overall volumetric mass transfer coefficient(K_(L)a)are 4.28×10^(-3) s^(-1) and 11.60×10^(-3) s^(-1) respectively at an initial pH of 6,βof 40,Co3(g)of 60 mg·L^(-1)and Q_(L) of 85 L·h^(-1) in deionized water,respectively.Meanwhile,the K_(c) and K_(L)a values of Fenhe water are0.88×10^(-3) s^(-1) and 2.51×10^(-3) s^(-1) lower than deionized water,respectively.In addition,the K_(c) and K_(L)a values in deionized water for the Cat/O_(3)-RPB system are 44.86%and 47.41%higher than that for the Cat/O_(3)-BR(bubbling reactor)system,respectively,indicating that the high gravity technology can facilitate the decomposition and mass transfer of ozone in heterogeneous catalytic ozonation and provide some insights into the industrial wastewater.

Packing Density Improvement through Addition of Limestone Fines, Superfine Cement and Condensed Silica Fume

Adoption of a low water/powder (W/P) ratio is the key to improve the strength and durability of concrete, which relies on a high packing density because fresh concrete requires excess water to offer flowability. To obtain a high packing density, powders with different particle sizes, including limestone fines (LSF), superfine cement (SFC), condensed silica fume (CSF), were added to the cement paste and the resulting packing densities were measured directly by a newly-developed wet packing test. Results demonstrated that addition of powders with a finer size would more significantly improve the packing density but the powders should be at least as fine as 1/4 of the OPC to effectively improve the packing density. Packing density and voids ratio relationship showed that a small increase in packing density can significantly decrease the voids ratio, which could allow the W/P ratio to be reduced to improve the strength and durability of the concrete without compromising the flowability.

Sulfonation of 1,4-diaminoanthraquinone leuco by chlorosulfonic acid:Kinetics and process intensification

The work herein employed a rotating packed bed(RPB)to intensify the sulfonation process of 1,4-diaminoanthraquinone leuco(DL)in an attempt to improve the yield of the product 1,4-diaminoanthra quinone-2-sulfonic acid(DSA).First,the effects of operating conditions in a stirred tank reactor(STR),including stirring speed,chlorosulfonic acid/DL molar ratio(η),solvent/DL mass ratio(ζ),reaction temperature and dropping speed of chlorosulfonic acid,on the yield of DSA were investigated.The yield of DSA can reach 87.34%under the optimal operating conditions:stirring speed of 500 r·min^(-1),ηof 4.5,ζof 7,reaction temperature of 150℃,dropping speed of 0.61 ml·min^(-1).In addition,the kinetics of the sulfonation process via the shrinking core model revealed that the reaction is controlled by diffusion via a product layer under the reaction temperature of 140℃.Furthermore,the RPB was employed to intensify the mass transfer between liquid and solid phases during the sulfonation reaction process.The results showed that the DSA yield of 92.69%obtained by RPB was 5.35%higher than that by STR,indicating that RPB can significantly intensify the mass transfer in the liquid-solid phase sulfonation reaction process.

【iPhone 4护航者】 mophie juice pack air snap

《个人电脑》编辑部从来就不缺观点,每位编辑对一个产品都有自己的观点,比如之前我是个铁杆的iPhone 4抵制者,但不少同事就掏钱买了,并对其交口称赞。我抵制iPhone 4是因为作为笔记本编辑，我实在无法忍受一个打电话发短信的东西。

Chromatin Decompaction Induced by Histone Acetylation Inuences the Sensitivity of DNA to Ionizing Radiation

The DNA molecules of eukaryotes are densely packed and exist within the nucleus as chromatin.Chromatin organization is highly dynamic and plays a crucial role in the repair of DNA damage caused by ionizing radiation,associating with acetylation of lysine residues in histones H3 and H4.

非常人所及 M-AUDIO TorqConectiv VinyICD Pack DJ专用音频工具

Torq Conectiv Vinyl/CD Pack是由M-Audio公司SynchroScience部门开发的首款DJ音频工具,这是为那些打算用笔记本做现场的DJ设计的产品。它由USB供电的4进4出音频接口和Torq DJ软件组成。通过内置的两张黑胶控制盘和CD控制盘可以控制软件走带和打碟。

Microstructure and high temperature oxidation resistance of Si-Y co-deposition coatings prepared on TiAl alloy by pack cementation process

In order to improve the high temperature oxidation resistance of TiAl alloy, Y modified silicide coatings were prepared by pack cementation process at 1030, 1080 and 1130 °C, respectively, for 5 h. The microstructures, phase constitutions and oxidation behavior of these coatings were studied. The results show that the coating prepared by co-depositing Si?Y at 1080 °C for 5 h has a multiple layer structure: a superficial zone consisting of Al-rich (Ti,Nb)5Si4 and (Ti,Nb)5Si3, an out layer consisting of (Ti,Nb)Si2, a middle layer consisting of (Ti,Nb)5Si4 and (Ti,Nb)5Si3, and aγ-TiAl inner layer. Co-deposition temperature imposes strong influences on the coating structure. The coating prepared by Si?Y co-depositing at 1080 °C for 5 h shows relatively good oxidation resistance at 1000 °C in air, and the oxidation rate constant of the coating is about two orders of magnitude lower than that of the bare TiAl alloy.

A STUDY ON ALUMINIDE COATINGS ON TiAl ALLOYS BY PACKCEMENTATION METHOD

The halide-activated pack cementation method is utilized to deposit aluminide coat- ings on TiAl alloys. Emphasis is placed on the effect of alloying elements on the aluminizing behavior of TiAl alloy. The addition of a small amount of Nb or Cr in the TiAl improves significantly the aluminizing kinetics of TiAl alloys by increasing the solid-state division of Al through the formation of stable TiAl3 layer. The TiAl3 layer formed on the TiAl alloyed with Nb or Cr has better toughness than the TiAl3 formed on the non-alloyed TiAl. The reason for better toughness of the coating formed on TiAl is that partial TiAl3 with tetragonal structure was changed to high symmetry cubic L12 structure since Nb or Cr was dissolved into TiAl3. The TiAl3 layer formed on the TiAl alloyed with Nb or Cr has much better oxidation resistance than the TiAl3 layer formed on the non-alloyed TiAl. It is attributed to change in the crystal structure of TiAl3 from the brittle tetragonal DO22 to the ductile cubic L12 by addition of small amount of Nb or Cr.

One-step synthesis of hydrophobic magnesium hydroxide nanoparticles and their application in flame-retardant polypropylene composites

Hydrophobic magnesium hydroxide(MH) nanoparticles were prepared by a one-step synthesis method in a high-gravity environment generated by a novel impinging stream–rotating packed bed(IS-RPB) reactor. The reactant solutions were simultaneously and continuously pumped into the IS-RPB reactor, and then Tween80 was added as a surface modifier. The morphology, structure, and properties of blank and hydrophobic MH were characterized. The effects of MH nanoparticles on the flame retardancy, thermal stability, and mechanical properties of PP/MH composites were also studied. We found that the obtained MH nanoparticles exhibited hexagonal lamella with a mean size of 30 nm, excellent hydrophobic properties(e.g., high water contact angle of 112°), and improved thermal stability of MH. The limiting oxygen index(LOI) further showed that increased MH loading can significantly improve flame-retardant performance, which reached 29.3% for PP/MH composites with 30 wt% hydrophobic samples. The thermal stability and mechanical properties of the PP/MH composites with hydrophobic samples were also much higher than those of PP/MH composites with blank MH. Results showed that the one-step synthesis had high potential application in the large-scale production of hydrophobic MH nanoparticles.

Particle-resolved simulation of packed beds by non-body conforming locally refined orthogonal hexahedral mesh

The traditional fixed-bed reactor design is usually not suitable for the low tube-to-particle diameter ratios(N = D/d b 8) where the local phenomena of channeling near the wall and backflow in the bed are dominant. The recent"solid particle" meshing method is too complicated for mesh generation, especially for non-spherical particles in large random packed beds, which seriously hinders its development. In this work, a novel high-fidelity mesh model is proposed for simulation of fixed bed reactors by combining the immersed boundary and adaptive meshing methods. This method is suitable for different shapes of particles, which ingeniously avoids handling the complex "contact point" problem. Several packed beds with two different shapes of particles are investigated with this model, and the local flow in the bed is simulated without geometrical simplification. The predicted pressure drop across the fixed bed and heat transfer of the single particle are in good agreement with the corresponding empirical relations. Compared with spherical particles, the packed bed packing with pentaphyllous particles has lower pressure drop and better heat/mass transfer performance, and it shows that this method can be used for the screening of particle shapes in a fixed bed.

Process Intensification of VOC Removal from High Viscous Media by Rotating Packed Bed

The removal of a volatile organic compound (VOC) from high viscous liquid was carried out in a rotat-ing packed bed (RPB) in this study. The mixed liquid of syrup and acetone was used as simulated high viscous polymer solution with acetone as the volatile compound. The influence of the rotating speed of RPB, liquid viscos-ity, liquid flow rate, vacuum degree, and initial acetone content in the liquid on acetone removal efficiency was in-vestigated. The experimental results indicated that the removal efficiency increased with increasing rotating speed and initial acetone content in the viscous liquid and decreased with increasing liquid viscosity and flow rate. It was also observed that acetone removal efficiency increased with an increasing vacuum degree and reached 58% at a vacuum degree of 0.1 MPa. By the comparison with a flash tank devolatilizer, it was found that acetone removal ef-ficiency in RPB increased by about 67%.

Experimental Investigation of Single-phase Flow in Structured Packing by LDV

To date, many models have been developed to calculate the flow field in the structured packing by the computational fluid dynamics （CFD） technique, but little experimental work has been carried out to serve the vali-dation of flow simulation. In this work, the velocity profiles of single-phase flow in structured packing are measured at the Reynolds numbers of 20.0, 55.7 and 520.1, using the laser Doppler velocimetry （LDV）. The time-averaged and instantaneous velocities of three components are obtained simultaneously. The CFD simulation is also carried out to numerically predict the velocity distribution within the structured packing. Comparison shows that the flow pattern, velocity distribution and turbulent kinetic energy （for turbulent flow） on the horizontal plane predicted by CFD simulation are in good agreement with the LDV measured data. The values of the x-and z-velocity components are quantitatively well predicted over the plane in the center of the packing, but the predicted y-component is sig-nificantly smaller than the experimental data. It can be concluded that experimental measurement is important for further improvement of CFD model.

Microstructures and wear resistance of chromium coatings on P110 steel fabricated by pack cementation

In order to obtain a high-performance surface on P110 steel that can meet the requirements in oil/gas field environment, the chromium coatings were fabricated by pack cementation. The chromium coatings differed in with/without the addition of La2O3. Scanning electron microscope （SEM）, energy dispersive X-ray spectrometer （EDS）, X-ray diffractometer （XRD） and microhardness tester were employed to investigate the surface morphologies, surface element distributions, microstructures, phase constitutions and microhardness of the coatings. Friction-wear tests of the P110 steel substrate and the coatings were conducted in air at ambient temperature and humidity. The results show that ＇uniform and continuous coatings are formed on P110 steel regardless of adding La2O3 or not. The chromium coatings consist of Cr23C6, Cr7C3, and （Cr, Fe）7C3. The La2O3-added chromium coating is more beneficial in terms of surface morphology, microstructure, thickness and microharduess as compared with the coating without adding La2O3. Chromizing treatment significantly improves the surface hardness and wear resistance of the P110 steel. The wear resistance of the tested samples can be sorted in the following sequence： La2O3-coating 〉 no RE-coating 〉bare P110 steel.

Preparation of p-Hydroxybenzaldehyde by Hydrolysis of Diazonium Salts Using Rotating Packed Bed

A new type of reactor,featured with impinging stream-rotating packed bed（IS-RPB）and coil pipes,was designed and used to prepare p-hydroxybenzaldehyde（PHB）by hydrolysis from diazonium salts.The influence of operating parameters,such as reaction temperature,reaction time and high gravity factor,on the yield of PHB was investigated.Compared with the traditional kettle-type reactor,the yield of PHB with the new reactor is increased significantly and the reaction time is much shorter.Under the optimum conditions,the yield of PHB is increased from 51%to 84.1%.The reactor offers an opportunity for replacing the traditional batch mode operation with a continuous process.

EXAMINATION OF THE SURFACE FREE ENERGY AND ACID-BASE PROPERTIES OF CELLULOSE BY THE COLUMN WICKING TECHNIQUE AND THE CRITICAL PACKING HEIGHT/DENSITY

The column wicking technique was applied to estimate the surface free energy of cellulose, the importance of which is to obtain a real effective capillary radius, Reff, initially from the plot of Washburn penetration distance versus time. Since the cellulose sample could not be packed with good reproducibility, therefore, Reff can not be obtained readily from the slope of the plot. A method was developed in this paper by uniting all apparent packing heights with a unique value to deduce a real effective capillary radius. Based on the defined critical packing height related to the critical packing density, the surface free energy and acid-base properties of cellulose Sigma C8002 were estimated.

NUMERICAL ANALYSIS OF QUASICONFORMAL MAPPINGS BY CIRCLE PACKINGS

Thurston proposed that conformal mappings can be approximated by circle packing isomorphisms and the approach can be implemented efficiently. Based on the circle packing methods the rate of convergence of approximating solutions for quasiconformal mappings in the plane is discussed.

Industrial application of the technique of removing Mo by a combination of moving packed bed and fluidized bed ion exchange

The application of the technique of removing molybdenum by moving packed bedand fluidized bed ion-exchange in a factory was described. The data showed that the Mo removalefficiency is above 99 percent, and the Mo content in APT (Ammonium Paratungstate) is controlledsteadily below 18 X l0^(-6), in the case of treating the feed liquor containing Mo 1.4 g/L. Thetechnique is simple and convenient in operation, good reusability of resin, loss consumption ofdesorption reagent and little pollution on environment. The loss of tungsten is less than 0.5percent. The technique bas been proved to be an economical and efficient process for Mo removal.

Determination of the intrinsic kinetics of iron oxide reduced by carbon monoxide in an isothermal differential micro-packed bed

The intrinsic kinetics of iron oxide reduced by carbon monoxide is evaluated by a method of online measuring concentration of off-gas in an isothermal differential micro-packed bed. Under the condition of getting away from the influence of gas diffusion and gas–solid heat transfer and mass transfer, the reaction of Fe2O3 to Fe3O4, Fe3O4 to Fe O and Fe O to Fe in the process of single reaction can be clearly distinguished from each other, and the relevant activation energy is characterized to be 75.4, 74.4, and 84.0 k J·mol-1, respectively. Therefore, the change of surface area in the reaction process due to losing oxygen could be easily calculated by combining it with pre-exponential parameters of Arrhenius equations. In conclusion, these kinetic parameters are verified by the experimental data for the process of ore reduced by carbon monoxide in a packed bed.

Molecular Structure of (1-Benzyl-4-phenyl-1H-1,2,3-triazol-5-yl)(4-bromophenyl) methanone: A Combined Experimental and Theoretical Study

One-pot three component reaction was used to synthesize 1,4,5-trisubstituted 1,2,3-triazole(A) from the corresponding acid chloride, benzyl azide and 1-copper(I) phenylethyne. The molecular structure was determined by single-crystal X-ray analysis. The compound crystallizes in the orthorhombic space group Pbca, a = 14.9815(14), b = 9.6496(10), c = 25.528(2) A, Z = 8. Furthermore, crystal packing demonstrated a molecular wall-like structure based on supramolecular chains of A, stabilized by CH···O, CH···Br, N···C and CH···π interactions. Molecular geometry in the ground state has been determined by density functional theory(DFT) by B3LYP/6-311G* basis set and compared with the experimental data. The computed vibrational frequencies are compared with the experimental FT-IR data and frontier molecular orbital analyses were performed at the same level of theory. Theoretical parameters are in good agreement with the corresponding X-ray diffraction values.

Corrosion and wear properties of TB2 titanium alloy borided by pack boriding with La_(2)O_(3)

To improve the surface performance of TB2 alloy,pack boriding was performed at 1100℃ for 20 h with 4 wt.%La_(2)O_(3).The composition and thickness of boride layer and corrosion and wear properties of borided TB2 alloy were measured.The results show that La_(2)O_(3) can promote the growth,continuity,and compactness of boride layer,and the length of TiB whisker increases from 16.80 to 21.84μm.The reason is that La_(2)O_(3) can react with B to form La−B active groups and further to improve the growth of the boride layer.The wear and corrosion resistances of TB2 alloy are enhanced by boriding with La_(2)O_(3).The wear mechanisms are adhesive wear and abrasive wear for unborided and borided TB2 alloys,respectively,and the corrosion mechanism is changed from local corrosion(unborided TB2 alloy)to uniform corrosion(borided TB2 alloy).