Design and Analysis of a Novel Shoulder Exoskeleton Based on a Parallel Mechanism

Power-assisted upper-limb exoskeletons are primarily used to improve the handling efficiency and load capacity.However,kinematic mismatch between the kinematics and biological joints is a major problem in most existing exoskeletons,because it reduces the boosting effect and causes pain and long-term joint damage in humans.In this study,a shoulder augmentation exoskeleton was designed based on a parallel mechanism that solves the shoulder dislocation problem using the upper arm as a passive limb.Consequently,the human–machine synergy and wearability of the exoskeleton system were improved without increasing the volume and weight of the system.A parallel mechanism was used as the structural body of the shoulder joint exoskeleton,and its workspace,dexterity,and stiffness were analyzed.Additionally,an ergonomic model was developed using the principle of virtual work,and a case analysis was performed considering the lifting of heavy objects.The results show that the upper arm reduces the driving force requirement in coordinated motion,enhances the load capacity of the system,and achieves excellent assistance.

Type Synthesis of Fully Decoupled Three Translational Parallel Mechanism with Closed-Loop Units and High Stifness

In order to solve the problem of weak stifness of the existing fully decoupled parallel mechanism, a new synthesis method of fully decoupled three translational (3T) parallel mechanisms (PMs) with closed-loop units and high stifness is proposed based on screw theory. Firstly, a new criterion for the full decoupled of PMs is presented that the reciprocal product of the transmission wrench screw matrix and the output twist screw matrix of PMs is a diagonal matrix, and all elements on the main diagonal are nonzero constants. The forms of the transmission wrench screws are determined by the criterion. Secondly, the forms of the actuated and unactuated screws can be obtained according to their relationships with the transmission wrench screws. The basic decoupled limbs are generated by combination of the above actuated and unactuated screws. Finally, a closed-loop units construction method is investigated to apply the decoupled mechanisms in a better way on the high stifness occasion. The closed-loop units are constructed in the basic decoupled limbs to generate a high-stifness fully decoupled 3T PM. Kinematic and stifness analyses show that the Jacobian matrix is a diagonal matrix, and the stifness is obviously higher than that of the coupling mechanisms, which verifes the correctness of the proposed synthesis method. The mechanism synthesized by this method has a good application prospect in vehicle durability test platform.

INVERSE KINEMATIC AND DYNAMIC ANALYSIS OF A 3-DOF PARALLEL MECHANISM

According to the structure character of the passive sub-chain of the 3TPS-TPparallel mechanism, the kinematic constraint equations of the movable platform are established,based on which the closed-form inverse kinematics formula of the parallel mechanism are presented.Through parting the spherical joints of the active sub-chains and using the force and momentequilibrium of both the active sub-chains and passive sub-chain, the constraint forces acting on theparted joints are determined. Subsequently, the analytic expressions of the actuator driving forcesare derived by means of the force equilibrium of the upper links of active sub-chains.

Comparative Analysis of Characteristics of the Coupled and Decoupled Parallel Mechanisms

The existence of coupling makes the parallel mechanism possess some special advantages over the serial mechanism, while it is just the coupling that brings about the parallel mechanism some limitations, such as complex workspace, high nonlinear relationship between input and output, difficulties in static and dynamic analysis, and the development of control system, which restricts its application fields. The decoupled parallel mechanism is currently one of the research focuses of the mechanism fields, while the study on the different characteristics between the deeoupled and coupled parallel mechanisms has not been reported. Therefore, this paper performs the systematic comparative analysis of the 3-RPUR and the 3-CPR parallel mechanisms. The features of the two mechanisms are described and their movement forms are analyzed with screw theory. The inverse and forward displacement solutions are solved and the Jacobian matrices are obtained. According to the Jacobian matrices and by using the theory of physical model of the solution space, the workspace, dexterity, velocity, payload capability, and stiffness of the mechanisms are analyzed with plotting the indices atlases. The research results prove that the effects of the coupling on the parallel mechanism are double-side, and then the adoption of the decoupled parallel mechanism should be determined by the requirements of the concrete application situation. The contents of this paper should be useful for the type synthesis and practical application of the parallel mechanism.

Biomimetic Shoulder Complex Based on 3-PSS/S Spherical Parallel Mechanism

The application of the parallel mechanism is still limited in the humanoid robot fields, and the existing parallel humanoid robot joint has not yet been reflected the characteristics of the parallel mechanism completely, also failed to solve the problem, such as small workspace, effectively. From the structural and functional bionic point of view, a three degrees of freedom（DOFs） spherical parallel mechanism for the shoulder complex of the humanoid robot is presented. According to the structure and kinetic characteristics analysis of the human shoulder complex, 3-PSS/S（P for prismatic pair, S for spherical pair） is chosen as the original configuration for the shouder complex. Using genetic algorithm, the optimization of the 3-PSS/S spherical parallel mechanism is performed, and the orientation workspace of the prototype mechanism is enlarged obviously. Combining the practical structure characteristics of the human shouder complex, an offset output mode, which means the output rod of the mechanism turn to any direction at the point a certain distance from the rotation center of the mechanism, is put forward, which provide possibility for the consistent of the workspace of the mechanism and the actual motion space of the human body shoulder joint. The relationship of the attitude angles between different coordinate system is derived, which establishs the foundation for the motion descriptions under different conditions and control development. The 3-PSS/S spherical parallel mechanism is proposed for the shoulder complex, and the consistence of the workspace of the mechanism and the human shoulder complex is realized by the stuctural parameter optimization and the offset output design.

Type Synthesis and Characteristic Analysis of a Family of 2-DOF Rotational Decoupled Parallel Mechanisms

It is widely used for the rotational parallel mechanism in the field of spatial orientation. While owing to the existence of coupling, the forward kinematic solution and the control of the general rotational parallel mechanism are especially difficult. If decoupling can be realized, the kinematic analysis of the mechanism will be very simple. Presently, the research of the parallel mechanism is focused on the inverse solution and structure optimization, and there is a lack of rotation decoupled parallel mechanisms （DPMs）. So this paper proposes a family of 2 degree of freedom （DOF） rotational DPMs based on the four-bar linkage mechanism, and performs a characteristic analysis. This family of DPMs is composed of a moving platform, a fixed base and three limbs. Taking U_RRU SPU DPM as an example, the motion feature of this DPM is analyzed with the constraint screw method, and its mobility is calculated by using the Modified Kutzbach-Grtibler criterion. The inverse and forward displacement problems of the proposed parallel mechanism are solved. The decoupled feature of the proposed parallel mechanism is validated by the deduction of the expression of the Jaeobian matrix. Three kinds of singularity conditions of this DPM are discussed, and the atlases of the output parameter concerning different geometric parameters are plotted with the theory of the physical model of the solution space. The proposition and characteristic analysis of the novel rotational DPMs in this paper should be useful for further research and application of the parallel mechanisms.

Novel Mobility Formula for Parallel Mechanisms Expressed with Mobility of General Link Group

The determination of virtual constraints is always one of the key and difficult problems in traditional mobility calculation. To make mobility calculation simple, considering avoiding virtual constraints, some new formulae have been presented, however these formulae can hardly intuitively reflect general link group＇s restrictions on output member and its influences on independence of output parameters, which is premise to the judgment of the properties of mobility. Towards the problem to reveal the intrinsic relationship between the degree of freedom（DOF） of a mechanism, the link group, and the dimension of output parameters, also to avoid determination of virtual constraint, based on the new concepts of the ＂DOF of general link group＂ and ＂node parameters＂, a new formula in the calculation of the mobility of mechanisms is presented that is expressed with DOFs of the general link groups and rank of motion parameters of base point of the output link. It is named GOM（mobility of groups and output parameter） formula. On the basis of new concepts of＂effective parameters＂ and ＂invalid parameters＂, a rule is put forward for solving the DOF of mechanisms with invalid parameters by GOM formula, that is, the base point parameters are the subset of effective parameters of link group. Thereafter, several examples are enumerated and the results coincide with the prototype data, which proves the validity of the proposed formula. Meanwhile, it is obtained that the necessary and sufficient condition for the judgment of output parameters independence is that each of the DOF of the link group is not less than zero. The proposed formula which is simple in calculation provides theoretical basis for the judgment of independence of output parameters and provides references for type synthesis of novel parallel mechanisms with independence requirements of their output parameters.

PERFORMANCE ANALYSIS AND KINEMATIC DESIGN OF PURE TRANSLATIONAL PARALLEL MECHANISM WITH VERTICAL GUIDE-WAYS

Performance analysis and kinematic design of the 3-PUU pure translational parallel mechanism with vertical guide-ways are investigated. Two novel performance indices, the critical slider stroke and the main section area of workspace, are defined; The expressions of two other indices, i.e. the global dexterity and global force transfer ratio are revised based on the main section of workspace. Using these indices, performance changes versus the varieties of dimensional parameters of mechanism are investigated in detail and the graphic descriptions of change tendencies of the performance indices are illustrated. By means of these obtained graphic descriptions, kinematic parameters for the 3-PUU pure translational parallel mechanism with better characteristics can be directly acquired.

Biped Walking Robot Based on a 2-UPU+2-UU Parallel Mechanism

Existing biped robots mainly fall into two categories： robots with left and right feet and robots with upper and lower feet. The load carrying capability of a biped robot is quite limited since the two feet of a walking robot supports the robot alternatively during walking. To improve the load carrying capability, a novel biped walking robot is proposed based on a 2-UPU＋2-UU parallel mechanism. The biped walking robot is composed of two identical platforms（feet） and four limbs, including two UPU（universal-prismatic-universal serial chain） limbs and two UU limbs. To enhance its terrain adaptability like articulated vehicles, the two feet of the biped walking robot are designed as two vehicles in detail. The conditions that the geometric parameters of the feet must satisfy are discussed. The degrees-of-freedom of the mechanism is analyzed by using screw theory. Gait analysis, kinematic analysis and stability analysis of the mechanism are carried out to verify the structural design parameters. The simulation results validate the feasibility of walking on rugged terrain. Experiments with a physical prototype show that the novel biped walking robot can walk stably on smooth terrain. Due to its unique feet design and high stiffness, the biped walking robot may adapt to rugged terrain and is suitable for load-carrying.

Dynamic Modeling and Analysis of 5‑PSS/UPU Parallel Mechanism with Elastically Active Branched Chains

To study the characteristics of the 5-prismatic–spherical–spherical(PSS)/universal–prismatic–universal(UPU)parallel mechanism with elastically active branched chains,the dynamics modeling and solutions of the parallel mechanism were investigated.First,the active branched chains and screw sliders were considered as spatial beam elements and plane beam element models,respectively,and the dynamic equations of each element model were derived using the Lagrange method.Second,the equations of the 5-PSS/UPU parallel mechanism were obtained according to the kinematic coupling relationship between the active branched chains and moving platform.Finally,based on the parallel mechanism dynamic equations,the natural frequency distribution of the 5-PSS/UPU parallel mechanism in the working space and elastic displacement of the moving platform were obtained.The results show that the natural frequency of the 5-PSS/UPU parallel mechanism under a given motion situation is greater than its operating frequency.The maximum position error is -0.096 mm in direction Y,and the maximum orientation error is -0.29°around the X-axis.The study provides important information for analyzing the dynamic performance,dynamic optimization design,and dynamic control of the 5-PSS/UPU parallel mechanism with elastically active branched chains.

Gait Analysis of a Radial Symmetrical Hexapod Robot Based on Parallel Mechanisms

Most gait studies of multi-legged robots in past neglected the dexterity of robot body and the relationship between stride length and body height.This paper investigates the performance of a radial symmetrical hexapod robot based on the dexterity of parallel mechanism.Assuming the constraints between the supporting feet and the ground with hinges,the supporting legs and the hexapod body are taken as a parallel mechanism,and each swing leg is regarded as a serial manipulator.The hexapod robot can be considered as a series of hybrid serial-parallel mechanisms while walking on the ground.Locomotion performance can be got by analyzing these equivalent mechanisms.The kinematics of the whole robotic system is established,and the influence of foothold position on the workspace of robot body is analyzed.A new method to calculate the stride length of multi-legged robots is proposed by analyzing the relationship between the workspaces of two adjacent equivalent parallel mechanisms in one gait cycle.Referring to service region and service sphere,weight service sphere and weight service region are put forward to evaluate the dexterity of robot body.The dexterity of single point in workspace and the dexterity distribution in vertical and horizontal projection plane are demonstrated.Simulation shows when the foothold offset goes up to 174 mm,the dexterity of robot body achieves its maximum value 0.164 4 in mixed gait.The proposed methods based on parallel mechanisms can be used to calculate the stride length and the dexterity of multi-legged robot,and provide new approach to determine the stride length,body height,footholds in gait planning of multi-legged robot.

Type Synthesis Method for the Translational Decoupled Parallel Mechanism Based on Screw Theory

Coupling is the significant characteristic of parallel mechanism,while it is just the coupling that brings about much difficulty for the configuration design,theoretical analysis and the development of the control system of the parallel mechanism. And recently,the research on the decoupled parallel mechanism becomes one of the research hot points in the mechanism fields. In this paper,a type synthesis method for the translational decoupled parallel mechanism( TDPM) is proposed based on the screw theory. To achieve the decoupling characteristics of the translational parallel mechanism,the translational decoupled criterion for type synthesis of the branches are presented in this paper. According to this criterion and the realization conditions of rotational degree of freedom of the mechanism proposed former,a large number of branches for the TDPM are obtained. Taking the three degrees of freedom( DOFs) TDPM as an example,the process of type synthesis is discussed in detail. Using this proposed type synthesis method,a serial of translational decoupled parallel mechanisms, including but not limited to all the existing typical 3-DOF TDPMs, are obtained, which identifies the correctness and effective of the method. The contents of this paper provide a reference and possess significant theoretical meanings for the synthesis and development of the novel decoupled parallel mechanisms.

Geometric Condition of 3UPS-S Parallel Mechanism in Singular Configuration

The existing researches on singularity of parallel mechanism are mostly limited to the property and regularity of singularity locus and there is no further research into the geometric relationship between uncontrolled kinematic screw and parallel mechanism in singularity. A 3UPS-S parallel mechanism is presented which fulfils 3-DOF in rotation. The regularity of nutation angle singularity is analyzed based on the Jacobian matrix, and the singularity surface of 3UPS-S parallel mechanisms is obtained. By applying the concept of reciprocal product in screw theory, the singular kinematic screw is derived when 3UPS-S parallel mechanism is in singularity. The geometric relationship between singular kinematic screw and singular configuration of 3UPS-S parallel mechanism is investigated by using programs in MATLAB. It is revealed that there are two kinds of situation. Firstly, the three limbs of 3UPS-S parallel mechanism intersect the singular kinematic screw in space simultaneously; Secondly, two limbs cross the singular kinematic screw while the third limb parallels with that screw. It is concluded that the nutation angle singularity of 3UPS-S parallel mechanism belongs to the singular linear complexes. This paper sheds light into and clarifies the geometric relationship between singular kinematic screw and singular configuration of 3UPS-S parallel mechanism.

Type Synthesis of Two-Degrees-of-Freedom Rotational Parallel Mechanism with Two Continuous Rotational Axes

The two-rotational-degrees-of-freedom（2R） parallel mechanism（PM） with two continuous rotational axes（CRAs） has a simple kinematic model.It is therefore easy to implement trajectory planning,parameter calibration,and motion control,which allows for a variety of application prospects.However,no systematic analysis on structural constraints of the 2R-PM with two CRAs has been performed,and there are only a few types of 2R-PM with two CRAs.Thus,a theory regarding the type synthesis of the 2R-PM with two CRAs is systematically established.First,combining the theories of reciprocal screw and space geometry,the spatial arrangement relationships of the constraint forces applied to the moving platform by the branches are explored,which give the 2R-PM two CRAs.The different distributions of the constraint forces in each branch are also studied.On the basis of the obtained structural constraints of branches,and considering the geometric relationships of constraint forces in each branch,the appropriate kinematic chains are constructed.Through the reasonable configuration of branch kinematic chains corresponding to every structural constraint,a series of new 2R-PMs with two CRAs are finally obtained.

ON THE DYNAMIC MODELING AND CONTROL OF 2-DOF PLANAR PARALLEL MECHANISM WITH FLEXIBLE LINKS

The object of study is about dynamic modeling and control for a 2degree-of-freedom (DOF) planar parallel mechanism (PM) with flexible links. The kinematic anddynamic equations are established according to the characteristics of mixed rigid and flexiblestructure. By using the singular perturbation approach (SPA), the model of the mechanism can beseparated into slow and fast subsystems. Based on the feedback linearization theory and inputshaping technique, the large scale rigid motion controller and the flexible link vibrationcontroller can be designed separately to achieve fast and accurate positioning of the PM.

Dynamic Accuracy Analysis of a 5PSS/UPU Parallel Mechanism Based on Rigid-Flexible Coupled Modeling

In order to improve the low output accuracy caused by the elastic deformations of the branch chains,a finite element-based dynamic accuracy analysis method for parallel mechanisms is proposed in this paper.First,taking a 5-prismatic-spherical-spherical(PSS)/universal-prismatic-universal(UPU)parallel mechanism as an example,the error model is established by a closed vector chain method,while its influence on the dynamic accuracy of the parallel mechanism is analyzed through numerical simulation.According to the structural and error characteristics of the parallel mechanism,a vector calibration algorithm is proposed to reduce the position and pose errors along the whole motion trajectory.Then,considering the elastic deformation of the rod,the rigid-flexible coupling dynamic equations of each component are established by combining the finite element method with the Lagrange method.The elastodynamic model of the whole machine is obtained based on the constraint condition of each moving part,and the correctness of the model is verified by simulation.Moreover,the effect of component flexibility on the dimensionless root mean square error of the displacement,velocity and acceleration of the moving platform is investigated by using a Newmark method,and the mapping relationship of these dimensionless root mean square errors to dynamic accuracy is further studied.The research work provides a theoretical basis for the design of the parameter size of the prototype.

A New Method for Type Synthesis of 2R1T and 2T1R 3-DOF Redundant Actuated Parallel Mechanisms with Closed Loop Units

The current type synthesis of the redundant actuated parallel mechanisms is adding active-actuated kinematic branches on the basis of the traditional parallel mechanisms,or using screw theory to perform multiple getting intersection and union to complete type synthesis.The number of redundant parallel mechanisms obtained by these two methods is limited.In this paper,based on Grassmann line geometry and Atlas method,a novel and effective method for type synthesis of redundant actuated parallel mechanisms(PMs)with closed-loop units is proposed.Firstly,the degree of freedom(DOF)and constraint line graph of the moving platform are determined successively,and redundant lines are added in constraint line graph to obtain the redundant constraint line graph and their equivalent line graph,and a branch constraint allocation scheme is formulated based on the allocation criteria.Secondly,a scheme is selected and redundant lines are added in the branch chains DOF graph to construct the redundant actuated branch chains with closed-loop units.Finally,the branch chains that meet the requirements of branch chains configuration criteria and F&C(degree of freedom&constraint)line graph are assembled.In this paper,two types of 2 rotational and 1 translational(2R1T)redundant actuated parallel mechanisms and one type of 2 translational and 1 rotational(2T1R)redundant actuated parallel mechanisms with few branches and closed-loop units were taken as examples,and 238,92 and 15 new configurations were synthesized.All the mechanisms contain closed-loop units,and the mechanisms and the actuators both have good symmetry.Therefore,all the mechanisms have excellent comprehensive performance,in which the two rotational DOFs of the moving platform of 2R1T redundant actuated parallel mechanism can be independently controlled.The instantaneous analysis shows that all mechanisms are not instantaneous,which proves the feasibility and practicability of the method.

New Family of 3-DOF UP-Equivalent Parallel Mechanisms with High Rotational Capability

Parallel mechanisms(PMs) having the same motion characteristic with a UP kinematic chain(U denotes a universal joint, and P denotes a prismatic joint) are called UP-equivalent PMs. They can be used in many applications, such as machining and milling. However, the existing UP-equivalent PMs suffer from the disadvantages of strict assembly requirements and limited rotational capability. Type synthesis of UP-equivalent PMs with high rotational capability is presented.The special 2 R1 T motion is briefly discussed and the fact that the parallel module of the Exechon robot is not a UP-equivalent PM is disclosed. Using the Lie group theory, the kinematic bonds of limb chains and their mechanical generators are presented. Structural conditions for constructing such UP-equivalent PMs are proposed,which results in numerous new architectures of UP-equivalent PMs. The high rotational capability of the synthesized mechanisms is illustrated by an example. The advantages of no strict assembly requirements and high rotational capability of the newly developed PMs will facilitate their applications in the manufacturing industry.

Synthesis of Branched Chains with Actuation Redundancy for Eliminating Interior Singularities of 3T1R Parallel Mechanisms

Although it is common to eliminate the singularity of parallel mechanism by adding the branched chain with actuation redundancy, there is no theory and method for the configuration synthesis of the branched chain with actuation redundancy in parallel mechanism. Branched chains with actuation redundancy are synthesized for eliminating interior singularity of 3-translational and 1-rotational（3T1R） parallel mechanisms. Guided by the discriminance method of hybrid screw group according to Grassmann line geometry, all the possibilities are listed for the occurrence of interior singularities in 3T1R parallel mechanism. Based on the linear relevance of screw system and the principles of eliminating parallel mechanism singularity with actuation redundancy, different types of branched chains with actuation redundancy are synthesized systematically to indicate the layout and the number of the branched chainsinterior with actuation redundancy. A general method is proposed for the configuration synthesis of the branched chains with actuation redundancy of the redundant parallel mechanism, and it builds a solid foundation for the subsequent performance optimization of the redundant actuation parallel mechanism.

Constraint and Mobility Change Analysis of Rubik’s Cube-inspired Reconfigurable Joints and Corresponding Parallel Mechanisms

The current research of reconfigurable parallel mechanism mainly focuses on the construction of reconfigurable joints.Compared with the method of changing the mobility by physical locking joints,the geometric constraint has good controllability,and the constructed parallel mechanism has more configurations and wider application range.This paper presents a reconfigurable axis(rA)joint inspired and evolved from Rubik’s Cubes,which have a unique feature of geometric and physical constraint of axes of joint.The effectiveness of the rA joint in the construction of the limb is analyzed,resulting in a change in mobility and topology of the parallel mechanism.The rA joint makes the angle among the three axes inside the groove changed arbitrarily.This change in mobility is completed by the case illustrated by a 3(rA)P(rA)reconfigurable parallel mechanism having variable mobility from 1 to 6 and having various special configurations including pure translations,pure rotations.The underlying principle of the metamorphosis of this rA joint is shown by investigating the dependence of the corresponding screw system comprising of line vectors,leading to evolution of the rA joint from two types of spherical joints to three types of variable Hooke joints and one revolute joint.The reconfigurable parallel mechanism alters its topology by rotating or locking the axis of rA joint to turn all limbs into different phases.The prototype of reconfigurable parallel mechanism is manufactured and all configurations are enumerated to verify the validity of the theoretical method by physical experiments.