Parameter Study of Some Key Structures for Cylinder Head

Using the method of the parameter study, some important dimensions of the cylinder head of an internal-combustion engine are analyzed. Under the mechanical load, the variational rules of the von Mises maximum stress on cylinder head are obtained, which are influenced by the thickness of the floor plate, head plate, jobbing sheet, standing partition board, and side plate of inlet port and exhaust port. A hypothesis is verified that there is an ideal matching point among those above-mentioned main parameters. The quantificational proportion relations, between these key structural parameters and von Mises maximum stress of cylinder head, can provide a good help for the cylinder head's structural design.

Theoretical Study on the Spectroscopic Parameters and Transition Properties of MgH Radical Including Spin-orbit Coupling

An accurate theoretical study on the MgH radical is reported by adopting the high-level relativistic MRCI＋Q method with a quintuple-zeta quality basis set. The reliable potential energy curves of the five A-S states of MgH are derived. Then the associated spectroscopic parameters are determined and found to be in good accordance with the available experimental results. The permanent dipole moments （PDMs） and the spin-orbit （SO） matrix elements of A-S states are computed. The results show that the abrupt changes of PDMs and SO matrix elements are attributed to the variations of electronic configurations at the avoided crossing point. The SOC effect leads to the five A-S states split into ten Ω states and results in the double potential well of （2）1//2 state. Finally, the transition properties from the （2）1//2, （1）3//2 and （3）1//2 states to the ground state X2∑＋1//2 transitions are obtained, including the transition dipole moments, Franck-Condon factors and radiative lifetimes.

Study of the Parameters of a Magnetic DC Plasma Jet

A Magnetic DC plasma torch has been developed. Magnetic field distributions of solenoid coils have been calculated electrodynamically. For Ar +H2 plasma, the effects of an akial magnetic field and gas flow rate on the characttristics of the plasma jet were studied. Electron temperature, density and plasma velocity at 80 mm from the nozzle have been measured using a floating double probe and a Mach probe. The values of the heat fluxes to substrate were derived from experimental data.

Simulation Study on the Controllable Dielectrophoresis Parameters of Graphene

The method of using dielectrophoresis （DEP） to assemble graphene between micro-electrodes has been proven to be simple and efficient. We present an optimization method for the kinetic formula of graphene DEP, and discuss the simulation of the graphene assembly process based on the finite element method. The simulated results illustrate that the accelerated motion of graphene is in agreement with the distribution of the electric field squared gradient. We also conduct research on the controllable parameters of the DEP assembly such as the alternating current （AC） frequency, the shape of micro-electrodes, and the ratio of the gap between electrodes to the characteristic/geometric length of graphene （λ）. The simulations based on the Clausius-Mossotti factor reveal that both graphene velocity and direction are influenced by the AC frequency. When graphene is close to the electrodes, the shape of micro-electrodes will exert great influence on the velocity of graphene. Also, λ has a great influence on the velocity of graphene. Generally, the velocity of graphene would be greater when λ is in the range of 0.4 0.6. The study is of a theoretical guiding significance in improving the precision and efficiency of the graphene DEP assembly.

The Study of the Grit-blasting Parameters and Their Effects on the Adhesive Strength of the Plasma Sprayed Coatings

Surface Preparation is very important in adhesive b on ding of spray coatings to the surface of a work piece. The common practice is gr it-blasting of the surface before subjecting it to the spray coating process. In this study, grit-blasting of an AISI 4130 steel (of different heat treatmen ts) with Al 2O 3 particles was studied. Various grit-blasting parameters such as blasting particle size, the distance between blasting nozzle and the work pi ece (25, 30 and 40 cm.), blasting pressure (3,4,5,6 and 7 bars), blasting time ( 3, 6 and 10 seconds), and the blasting angle (45° and 90°) were examined in or der to find the optimum roughness. The mean roughness (Ra) of the grit-blasted surfaces were measured and the vari ations of the roughness with respect to the above mentioned variables were studi ed. The results show that by increasing blasting time, surface roughness increas es up to a maximum and then slightly decreases it with further duration of t he process. On the other hand a lengthy blasting causes some undesirable results such as an increase in residual particles between surface irregularities. There fore an optimum blasting time is of great importance. Increasing the blasting pr essure also provides a rougher surface, but in grit blasting of harder specimens the surface roughness decreases when the pressure reaches a certain limit. About the blasting angle, it was noticed that an angle of 45° results in less r esidual particles between the surface irregularities, in comparison to the angle of 90°. After grit-blasting, the specimens were plasma spray coated with 80% ZrO 2-20 % Y 2O 3 powder. The adhesive strength of the coating to the substrate was the n measured according to the DIN 50160 standard. The results show that for a certain base metal, the adhesive strength is directl y related to the surface roughness of the base material. Residual particles afte r grit-blasting the surface of the specimens can also have a strong deteriorati ng effect on adhesive strength. Finally, it was shown that the hardness of the b ase material had a direct effect on the adhesive strength of the sprayed coating s.

Optimization Study of Steam Turbine Cold End Parameters

A lot of study has been made for the design and defining hot end initial parameters of steem turbine of large thermal power plant at home and abroad. But little study has been performed for the reasonable selection of some cold end parameters of steam turbine. The steam turbine cold end parameters defined in actual engineering project are somewhat unreasonable frequently. This paper describes some opinions for selecting some of the steam turbine cold end parameters, especially that of the turbine design back pressure and low pressure cylinder last stage blade length based on the regional features of meteorological conditions in China in association with the optimization of thermal power plant circulating water system.

A study on effective parameters of electric cortical stimulation for motor-sensory brain mapping

Objective The purpose of the study was to investigate the effective parameters of electric cortex stimulation (ECS) for functional brain mapping. Methods We collected 21 subjects who underwent epilepsy surgeries consecutively in Beijing Institute of Functional Neurosurgery with the epileptogenic zone located in perirolandic areas from

PARACRYSTAL STRUCTURE PARAMETERS STUDIES IN LDPE/EPO BLENDS WITH VARIANCE-RANGE FUNCTION METHOD

X-ray diffraction line profiles of low density polyethylene(LDPE)/ (ethylene-propylene-octene-1)copolymer(EPO)blends have been analyzed with variance range function method.Theories for determining the microparacrystallite size and the distortion parameter from single reflection have been described,and the value of these two parameters at (110)and(200)directions have been determined.

Studies on the Construction Parameter of an Artificial Occluded Cell for In-situ Inspection of the Propagation Rate of Localized Corrosion

An artificial localized corrosion system is assembled and some parameters related to the localized corrosion in active dissolution state (i.e., non-passive state) have been studied. The results showed that the developed electrochemical system can satisfactorily imitate a naturally formed localized corrosion and the coupling current can indicate the maximum localized propagating rate. In this artificial system, the anodic dissolution reaction followed the auto-catalytic mechanism. The localized corrosion current density was dependent on the area ratio R of the cathode to the occluded anode. While R was equal to or more than 6, the coupling current reached at a maximum value and did not alter with the increase in R-value. Therefore, R=7 is chosen as one of these optimum parameters used in constructing the system, with which the biggest galvanic current might be obtained. In contrast, the thickness of the polymer filler separating the occluded anode area from the bulk electrolyte solution and the volume of the occluded anode area did not affect the corrosion current obviously. They might affect the response time to approach a steady state.

Bending of Timoshenko beam with effect of crack gap based on equivalent spring model

Considering the effect of crack gap, the bending deformation of the Timoshenko beam with switching cracks is studied. To represent a crack with gap as a nonlinear unidirectional rotational spring, the equivalent flexural rigidity of the cracked beam is derived with the generalized Dirac delta function. A closed-form general solution is obtained for bending of a Timoshenko beam with an arbitrary number of switching cracks. Three examples of bending of the Timoshenko beam are presented. The influence of the beam＇s slenderness ratio, the crack＇s depth, and the external load on the crack state and bending performances of the cracked beam is analyzed. It is revealed that a cusp exists on the deflection curve, and a jump on the rotation angle curve occurs at a crack location. The relation between the beam＇s deflection and load is bilinear, each part corresponding to an open or closed state of crack, respectively. When the crack is open, flexibility of the cracked beam decreases with the increase of the beam＇s slenderness ratio and the decrease of the crack depth. The results are useful in identifying non-destructive cracks on a beam.

Axisymmetrical analytical solution for vertical vibration of end-bearing pile in saturated viscoelastic soil layer

Based on elasticity and the theory of saturated porous media, and regarding the pile and the soil as a single phase elastic and a saturated viscoelastic media, respectively, the dynamical behavior of vertical vibration of an end-bearing pile in a saturated viscoelastic soil layer is investigated in the frequency domain using the Helmholtz decomposition and variable separation method. The axisymmetrical analytical solutions for vertical vibrations of the pile in a saturated viscoelastic soil layer are obtained, and the analytical expression of the dynamical complex stiffness of the pile top is presented. Responses of dynamic stiffness factor and equivalent damping of pile top with respect to the frequency are shown in figures using a numerical method. Effects of the saturated soil parameters, modulus ratio of the pile to soil, slenderness ratio of pile and pile＇s Poisson ratio, etc. on the stiffness factor and damping are examined. It is shown that, due to the effect of the transversal deformation of the pile and the radial force of the saturated viscoelastic soil acting on the pile, the dynamic stiffness factor and the damping derived from the axisymmetrical solution are greatly different from those derived from the classical Euler-Bernoulli rod model, especially at some specific excitation frequencies. Therefore, there are limitations on applicability of the Euler-Bernoulli rod model in analyzing verticai vibration of the pile. More accurate analysis should be based on a three-dimensional model.

NONLINEAR DYNAMICAL CHARACTERISTICS OF PILES UNDER HORIZONTAL VIBRATION

The pile-soil system is regarded as a visco-elastic half-space embedded pile. Based on the method of continuum mechanics, a nonlinear mathematical model of pile-soil interaction was established-a coupling nonlinear boundary value problem. Under the case of horizontal vibration, the nonlinearly dynamical characteristics of pile applying the axis force were studied in horizontal direction in frequency domain. The effects of parameters, especially the axis force on the stiffness were studied in detail. The numerical results suggest that it is possible that the pile applying an axis force will lose its stability. So,the effect of the axis force on the pile is considered.

Crosstalk Study in a FBG-MOC-Based OXC Using Scattering Parameters

Crosstalk in FBG-MOC-based OXCs is simulated using scattering parameters and compared with that in FBG-OC-based OXCs. The former is able to enhance the output power without significant degradation in signal-to-crosstalk ratio compared with the latter.

EXPERIMENTAL STUDY OF CHUANXIONG ON CEREBROVASCULAR HEMODYNAMIC PARAMETERS

In the experimental rabbit arteriosclerosis, the change of the cerebrovascular hemodynamic parameters (CVHP) and the effect of Chuanxiong (CX) on CVHP were observed. In arteriosclerosis group (AS group), the mean flow (Qmean), mean velocity (Vmean), maximal velocity (V max) and minimal velocity (Vmin) of the carotid blood flow and cerebrovascular compliance for zero pressure (CO) were significantly decreased (P < 0.05, 0.01), but the values of cerebrovascular peripheral resistance (R) and characteristic impedance (Zc) were significantly increased (P<0.05 and 0.01), and the value of R showed significant positive correlation with the extent of carotid lesions (P < 0.01). All indexes of CVHP of the Chuanxiong group (CX group) were close to and had no significant difference from those of the normal group (N group) but Qmean, Vmean, Vmin, CO and R were significantly better than those of the AS group (P<0.05, 0.01). These results showed that CX can effectively improve cerebrovascular hemodynamics.

Parameter studies and evaluation principles of delamination damage in laminated composites

Delamination represents one of the most severe failure modes in composite laminates,especially when they are subjected to uniaxial compression loads.The evaluation of the delamination damage has always been an essential issue of composite laminates for durability and damage tolerance in engineering practice.Focusing on the most typical and representative elliptical delamination issue,an analytical model simultaneously considering the conservative buckling process and non-conservative delamination propagation process is implemented.Various computational cases considering different delamination depths,directions,aspect ratios,and areas are established,and the predicted results based on the analytical model are carefully compared.Effects of these geometrical delamination parameters on the buckling,delamination propagation,and failure behaviors of composite laminates are thoroughly analyzed,and innovative evaluation principles of the delamination damage have been concluded.It is found that the delamination area is the key factor that truly affecting the failure behaviors of delaminated composites,and the local/global buckling and failure loads show clear linearity with the delamination area,whilst the delamination depth and direction only have slight effects.

Parametric study on damage control design of SMA dampers in frame-typed steel piers

This paper focuses on damage control design of SMA dampers in steel frame piers.A parametric study based on time history analyses is carried out on frametyped bridge piers with axial-type SMA damping device.The parameters examined are design parameters of strength ratioαF and stiffness ratioαK.Seismic performance indexes on displacement and strain are investigated under three JRA recommended Level 2 Ground TypeПstrong earthquake motions.Design recommendations are suggested following the results of the parametric study.

Parameter studies on impact in a lap joint

To represent a loose lap joint, a beam impacting four springs with gaps is modeled. Modal analysis with base excitation is solved, and time histories of contact points are closely monitored. Using the impulse during steady state response, six influential parameters are studied： damping ratio, contact stiffness, intermediate contact position, gap, excitation amplitude and beam height. For all parameters, the system response is highly controlled by modes with two contacting springs. Each parameter＇s effect on system response is presented including unstable regions, unique trend behaviours result. Recommendations for structural designers are also noted.

Experimental and numerical investigation on opposing plasma synthetic jet for drag reduction

Experimental and numerical studies are carried out to validate the potential of opposing Plasma Synthetic Jet(PSJ)for drag reduction for a hemisphere.Firstly,flow field changes of opposing PSJ are analyzed by comparing the experimental schlieren images and simulation results in a supersonic free stream of Mach number 3.As PSJ is a kind of unsteady pulsed jet,the shock standoff distance increases initially and then decreases under the control of PSJ,which corresponds to the change of the strength of PSJ.Accordingly,the amount of drag reduction of the hemisphere increases initially and then decreases.It is found that there is a short period of“drag rise”during the formation of PSJ before the drag reduction,which is induced by the generation of normal shock waves and the area difference of the cavity wall of PSJ Actuator(PSJA).Secondly,the effects of five parameters,including exit diameter,discharge energy of PSJA,Mach number,static pressure of incoming flow and angle of attack,on drag reduction of opposing PSJ were studied in detail by using numerical method.It is found that the Maximum Pressure Ratio(MPR)has a significant impact on the average drag reduction for a configuration-determined PSJA.For the configuration selected in this study,the flow field of opposing PSJ shows typical Short Penetration Mode(SPM)in a control cycle of PSJ when the MPR is less than 0.89.However,the flow field shows typical Long Penetration Mode(LPM)at some time when the MPR is bigger than 0.89.Relatively better drag reduction is achieved in this case.

Mass transfer mechanisms in fixed-bed adsorption of erythromycin

The equilibrium and kinetic characteristics of the adsorption of erythromycin to Sepabeads SP825 were determined.The equilibrium data in a batch system was well described by a Langmuir isotherm.The separation performance was investigated in a fixed-bed system with respect to the adsorption superficial velocity,ionic strength and pH.A mathematical model was used to simulate the mass transfer mechanism,taking film mass transfer,pore diffusion and axial dispersion into account.The model predictions were consistent with the experi-mental data and were consequently used to determine the mass transfer coefficients.