High-Volume Mineral Admixtures Cement: The Effects of Particle Size Distribution

The effects of high-volume slag-fly ash cement with different particle sizes on hydration degree,microstructure and mechanical properties were systematically studied,by means of laser particle size(DLS),X-ray diffraction (XRD),comprehensive thermal analysis (TG-DTA),scanning electron microscopy(SEM) and mechanical properties tests.The results show that suitable particle size distribution of cementitious material has significantly promoting effects on hydration reaction rate and mechanical properties.Compared with slag without further grinding,the slag after ball milling for 4 h has an obvious improvement in reactivity,which also provides a faster hydration rate and higher compressive strength for the cementitious material.When the slag milled for 1 and 4 h is mixed at a mass ratio of 2:1 (i e,slag with D_(50) of 7.4μm and average size of 9.9μm,and slag with D_(50) value of 2.6μm and average size of 5.3μm),and a certain amount of fly ash is added in,the most obvious improvement of compressive strength of cement is achieved.

Particle size spatial distribution in landslide dams

The particle composition and spatial distribution of landslide-induced dam bodies are critical geotechnical parameters for studying the hazards of dam-break floods.However,current research often neglects the influence of the initial particle composition and spatial distribution of the landslide on the particle composition and spatial distribution of the landslide dam.This study investigated the impact of initial particle size distribution,volume,and sliding length on the energy and velocity changes of characteristic particles during the sliding process and the spatial distribution of particle sizes in the landslide dam body.Numerical simulations and physical models were employed to examine the effects of sequential gradient arrangements(where particle sizes decrease from top to bottom)and four other different initial particle arrangements on the energy and velocity changes of particles and the spatial distribution of particle sizes in the dam body.The study reveals the characteristics of translational and rotational energy of different particles and the laws of mechanical energy conversion,obtaining the spatial distribution patterns of particle sizes in landslide-induced dams.The results show that under the sequential gradient arrangement,the energy dissipation of the landslide movement is lower,with larger particles mainly distributed at the distal end and smaller particles at the proximal end of the landslide dam.In contrast,under the reverse gradient arrangement,the energy dissipation of the landslide movement is higher,and the distribution pattern of the dam particles is opposite to that of the sequential gradient arrangement.For the other arrangement modes,the spatial distribution of dam particles falls between the aforementioned two.There is a positive correlation between particle size and translational kinetic energy within the particle flow during the landslide process,and rotational motion increases energy dissipation.Under constant slope conditions,sliding length does not affect the movement pattern of the particle flow or the spatial distribution of particles in the dam body.The findings of this study provide a scientific basis for the accurate simulation and prediction of dam-break flood processes.

Extended wet sieving method for determination of complete particle size distribution of general soils

The traditional standard wet sieving method uses steel sieves with aperture?0.063 mm and can only determine the particle size distribution(PSD)of gravel and sand in general soil.This paper extends the traditional method and presents an extended wet sieving method.The extended method uses both the steel sieves and the nylon filter cloth sieves.The apertures of the cloth sieves are smaller than 0.063 mm and equal 0.048 mm,0.038 mm,0.014 mm,0.012 mm,0.0063 mm,0.004 mm,0.003 mm,0.002 mm,and 0.001 mm,respectively.The extended method uses five steps to separate the general soil into many material sub-groups of gravel,sand,silt and clay with known particle size ranges.The complete PSD of the general soil is then calculated from the dry masses of the individual material sub-groups.The extended method is demonstrated with a general soil of completely decomposed granite(CDG)in Hong Kong,China.The silt and clay materials with different particle size ranges are further examined,checked and verified using stereomicroscopic observation,physical and chemical property tests.The results further confirm the correctness of the extended wet sieving method.

On the critical particle size of soil with clogging potential in shield tunneling

Shield tunneling is easily obstructed by clogging in clayey strata with small soil particles.However,soil clogging rarely occurs in strata with coarse-grained soils.Theoretically,a critical particle size of soils should exist,below which there is a high risk of soil clogging in shield tunneling.To determine the critical particle size,a series of laboratory tests was carried out with a large-scale rotary shear apparatus to measure the tangential adhesion strength of soils with different particle sizes and water contents.It was found that the tangential adhesion strength at the soilesteel interface gradually increased linearly with applied normal pressure.When the particle size of the soil specimen was less than 0.15 mm,the interfacial adhesion force first increased and then decreased as the water content gradually increased;otherwise,the soil specimens did not manifest any interfacial adhesion force.The amount of soil mass adhering to the steel disc was positively correlated with the interfacial adhesion force,thus the interfacial adhesion force was adopted to characterize the soil clogging risk in shield tunneling.The critical particle size of soils causing clogging was determined to be 0.15 mm.Finally,the generation mechanism of interfacial adhesion force was explored for soils with different particle sizes to explain the critical particle size of soil with clogging risk in shield tunneling.

Analysis of a landfill cover without geomembrane using varied particle sizes of recycled concrete

Previous studies have demonstrated the effectiveness of a novel three-layer landfill cover system constructed with recycled concrete aggregates(RCAs)without geomembrane in both laboratory and field.However,no systematic investigation has been carried out to optimize the combination of the particle sizes for fine-grained RCAs(FRC)and coarse-grained RCAs(CRC)that can be used for the three-layer landfill cover system.The aim of this paper is to assist engineers in designing the three-layer landfill cover system under a rainfall of 100-year return period in humid climate conditions using an easily controlled soil parameter D10 of RCAs.The numerical study reveals that when D10 of FRC increases from 0.05 mm to 0.16 mm,its saturated permeability increases by 10 times.As a result,a larger amount of rainwater infiltrates into the cover system,causing a higher lateral diversion in both the top FRC and middle CRC layers.No further changes in the lateral diversion are observed when the D10 value of FRC is larger than 0.16 mm.Both the particle sizes of FRC and CRC layers are shown to have a minor influence on the percolation under the extreme rainfall event.This implies that the selection of particle sizes for the FRC and CRC layers can be based on the availability of materials.Although it is well known that the bottom layer of the cover system should be constructed with very fine-grained soils if possible,this study provides an upper limit to the particle size that can be used in the bottom layer(D10 not larger than 0.02 mm).With this limit,the three-layer system can still minimize the water percolation to meet the design criterion(30 mm/yr)even under a 100-year return period of rainfall in humid climates.

An image segmentation method of pulverized coal for particle size analysis

An important index to evaluate the process efficiency of coal preparation is the mineral liberation degree of pulverized coal,which is greatly influenced by the particle size and shape distribution acquired by image segmentation.However,the agglomeration effect of fine powders and the edge effect of granular images caused by scanning electron microscopy greatly affect the precision of particle image segmentation.In this study,we propose a novel image segmentation method derived from mask regional convolutional neural network based on deep learning for recognizing fine coal powders.Firstly,an atrous convolution is introduced into our network to learn the image feature of multi-sized powders,which can reduce the missing segmentation of small-sized agglomerated particles.Then,a new mask loss function combing focal loss and dice coefficient is used to overcome the false segmentation caused by the edge effect.The final comparative experimental results show that our method achieves the best results of 94.43%and 91.44%on AP50 and AP75 respectively among the comparison algorithms.In addition,in order to provide an effective method for particle size analysis of coal particles,we study the particle size distribution of coal powders based on the proposed image segmentation method and obtain a good curve relationship between cumulative mass fraction and particle size.

Effect of particle size of single-crystalline hierarchical ZSM-5 on its surface mass transfer in n-heptane catalytic cracking

Single-crystalline hierarchical ZSM-5 zeolites with different particle sizes(namely 100,140,and 200 nm)were successfully prepared by adjusting the amount of tetrapropylammonium hydroxide(TPAOH),and investigated in n-heptane catalytic cracking reaction.Diffusional measurements by zero-length column(ZLC)method showed that the apparent diffusivities of n-heptane decreased with the reduction of particle size,indicating the existence of surface barriers.Moreover,with the decrease of particle size,the additional diffusion path length increased,which meant the influence of surface barriers became more apparent.Despite the change of surface barriers,the intracrystalline diffusion still dominated the overall diffusion.Catalytic performance showed that the zeolite with smaller particle size had better stability.

The type of lipid supplement has crucial implications for forage particle size in calf starter diets

Background Forage inclusion in starters of young dairy calves has become an acceptable strategy in the last decade.To compensate for the lower energy provided by forage,concurrent lipid supplementation can be proposed.How-ever,ruminal microbial activity and forage digestibility may be decreased by lipid supplementation.We hypothesized that the composite effect of forage and lipid supplements may be dependent on forage particle size and the type of lipid supplement.Therefore,we evaluated the effect of long(LP;geometric mean,4.97 mm)vs.short alfalfa hay particle sizes(SP;geometric mean,1.26 mm)with either soybean oil(SBO)or palm fatty acids(PLF)as lipid source in a 2×2 factorial design with treatments SP-SBO,SP-PLF,LP-SBO,and LP-PLF.Treatments(n=13 with 6 males and 7 females each)were offered to Holstein calves(3 days old)with equal amounts of lipid(25 g/kg DM)through-out the experimental period.The milk offering scheme(d 1 to 53)was equal for all groups.Data collection continued until 20 d post-weaning.Results Interaction between forage particle size and lipid supplement was significant for the following readouts:the highest and lowest starter intakes during the pre-weaning period occurred in LP-PLF and LP-SBO,respectively.This was associated with similarly contrasting changes in average daily gain(ADG)during the post-weaning period,body weight at the end of experiment,withers height,digestibility of organic matter and neutral detergent fiber,and blood serum concentrations of glucose,beta-hydroxybutyrate,and insulin during the pre-weaning period.Dur-ing both pre-and post-weaning periods,the highest and lowest urinary excretion of allantoin and total purine deriva-tives,representing microbial protein synthesis,were observed in LP-PLF and LP-SBO,respectively,indicating that those diets were most and least favorable for rumen development.Irrespective of forage particle size,supplemental SBO vs.PLF increased serum malondialdehyde as an oxidative stress indicator across periods,increased blood urea nitrogen and feed efficiency in the pre-weaning period,and reduced hip height during the post-weaning period.Conclusions It can be concluded that feeding a rumen-inert,mostly saturated fatty acid source with alfalfa hay as long particle size is recommended with view on performance,whereas a combination soybean oil rich in unsatu-rated fatty acids should not be provided to milk-fed Holstein calves together with long particle forage.Feeding soybean oil and alfalfa hay as long particles is not advisable mainly due to lower starter consumption and impaired development of ruminal function.If dietary supplementation of soybean oil is applied,incorporation of forage as small particles should be preferred to support rumen development.

The Effects of the Particle Size Ratio on the Behaviors of Binary Granular Materials

The particle size ratio(PSR)is an important parameter for binary granular materials,which may aect the microstructure and macro behaviors of granular materials.However,the eect of particle ratio on granular assemblies with dierent arrangements is still unclear.To explore and further clarify the eect of PSR in dierent packing structures,three types of numerical samples with regular,layered,and random packing are designed.Numerical results show that PSR has signi􀀀cant eects on binary granular samples with regular packing.The larger the PSR,the stronger the strength,the larger the modulus,and the smaller the angle between the shear band and the load direction.And a theoretical solution of the peak stress ratio vs.PSR is obtained for regular packing,and the results by DEM are in good agreement with the theoretical solution.Under layered packing,PSR has little eect on peak stress ratio due to similar microstructure obtained with the changing of PSR.The modulus slightly increased with the increase of PSR.Under random packing with small grain content of 50%,PSR has little eect in the range of 0.5–0.9,but in a larger range,larger PSR leads to greater modulus.

Study of deep transportation and plugging performance of deformable gel particles in porous media

Deformable gel particles(DGPs) possess the capability of deep profile control and flooding. However, the deep migration behavior and plugging mechanism along their path remain unclear. Breakage, an inevitable phenomenon during particle migration, significantly impacts the deep plugging effect. Due to the complexity of the process, few studies have been conducted on this subject. In this paper, we conducted DGP flow experiments using a physical model of a multi-point sandpack under various injection rates and particle sizes. Particle size and concentration tests were performed at each measurement point to investigate the transportation behavior of particles in the deep part of the reservoir. The residual resistance coefficient and concentration changes along the porous media were combined to analyze the plugging performance of DGPs. Furthermore, the particle breakage along their path was revealed by analyzing the changes in particle size along the way. A mathematical model of breakage and concentration changes along the path was established. The results showed that the passage after breakage is a significant migration behavior of particles in porous media. The particles were reduced to less than half of their initial size at the front of the porous media. Breakage is an essential reason for the continuous decreases in particle concentration, size, and residual resistance coefficient. However, the particles can remain in porous media after breakage and play a significant role in deep plugging. Higher injection rates or larger particle sizes resulted in faster breakage along the injection direction, higher degrees of breakage, and faster decreases in residual resistance coefficient along the path. These conditions also led to a weaker deep plugging ability. Smaller particles were more evenly retained along the path, but more particles flowed out of the porous media, resulting in a poor deep plugging effect. The particle size is a function of particle size before injection, transport distance, and different injection parameters(injection rate or the diameter ratio of DGP to throat). Likewise, the particle concentration is a function of initial concentration, transport distance, and different injection parameters. These models can be utilized to optimize particle injection parameters, thereby achieving the goal of fine-tuning oil displacement.

Coordination of distinctive pesticide adjuvants and atomization nozzles on droplet spectrum evolution for spatial drift reduction

Pesticide adjuvants,as crop protection products,have been widely used to reduce drift loss and improve utilization efficiency by regulating droplet spectrum.However,the coordinated regulation mechanisms of adjuvants and nozzles on droplet spectrum remain unclear.Here,we established the relationship between droplet spectrum evolution and liquid atomization by investigating the typical characteristics of droplet diameter distribution near the nozzle.Based on this,the regulation mechanisms of distinctive pesticide adjuvants on droplet spectrum were clarified,and the corresponding drift reduction performances were quantitively evaluated by wind tunnel experiments.It shows that the droplet diameter firstly shifts to the smaller due to the liquid sheet breakup and then prefers to increase caused by droplet interactions.Reducing the surface tension of sprayed liquid facilitates the uniform liquid breakup and increasing the viscosity inhibits the liquid deformation,which prolong the atomization process and effectively improve the droplet spectrum.As a result,the drift losses of flat-fan and hollow cone nozzles are reduced by about 50%after adding organosilicon and vegetable oil adjuvants.By contrast,the air induction nozzle shows a superior anti-drift ability,regardless of distinctive adjuvants.Our findings provide insights into rational adjuvant design and nozzle selection in the field application.

Modeling for critical state line of granular soil with evolution of grain size distribution due to particle breakage

Determination of the critical state line(CSL)is important to characterize engineering properties of granular soils.Grain size distribution(GSD)has a significant influence on the location of CSL.The influence of particle breakage on the CSL is mainly attributed to the change in GSD due to particle breakage.However,GSD has not been properly considered in modeling the CSL with influence of particle breakage.This study aims to propose a quantitative model to determine the CSL considering the effect of GSD.We hypothesize that the change of critical state void ratio with respect to GSD is caused by the same mechanism that influences of the change of minimum void ratio with respect to GSD.Consequently,the particle packing model for minimum void ratio proposed by Chang et al.(2017)is extended to predict critical state void ratio.The developed model is validated by experimental results of CSLs for several types of granular materials.Then the evolution of GSD due to particle breakage is incorporated into the model.The model is further evaluated using the experimental results on rockfill material,which illustrates the applicability of the model in predicting CSL for granular material with particle breakage.

Structural and size evolution of indium nanoparticles embedded in aluminum synthesized by ion implantation

The structural and the size evolution of embedded In nanoparticles in Al synthesized by ion implantation and subsequent annealing are experimentally investigated. The average radius r of In nanoparticles is determined as a function of annealing time in a temperature range between 423 K and 453 K. The structural transition of In nanoparticles with the crystallographic orientation In （200）[002]｜｜Al （200）[002] is observed to change into In （111）[110]｜｜Al （002）[110] with a critical particle radius between 2.3 nm and 2.6 nm. In addition, the growth of In nanoparticles in the annealing process is evidently governed by the diffusion limited Ostwald ripening. By further analyzing the experimental data, values of diffusion coefficient and activation energy are obtained.

In-Situ Measuring the Particle Mean Size and Dust Concentration by Near-Forward Small Angle Light Scattering

本文综合前向小角光散理论及消光原理，提出一种测量粉尘平均粒径及粉尘浓度的光学方法．该方法测量透过粉尘的散射光在前向两个空间立体角内的光强及出射光强，可以方便地计算出粉尘的平均粒径及粉尘浓度的大小．实验结果表明该方法可作为一种在线的测尘方法．

Effect of proteins,polysaccharides,and particle sizes on sludge dewaterability

Four batch experiments of hydrolysis and acidification were carried out to investigate the distributions of proteins （PN） and polysaccharides （PS） in the sludge, the PN/PS ratio, the particle sizes, and their relationship with sludge dewaterability （as determined by capillary suction time, CST）. The sludge flocs were stratified through centrifugation- and ultrasound-based method into four fractions： （1） slime, （2） loosely bound extracellular polymeric substances （LB-EPS）, （3） tightly bound EPS （TB-EPS）, and （4） pellet. The results showed that PN was mainly partitioned in the pellet （80.7%） and TB-EPS （9.6%） fractions, while PS distributed evenly in the four fractions. During hydrolysis and acidification, PN was transferred from the pellet and TB-EPS fractions to the slime fraction, but PS had no significant transfer trends. The mean particle sizes of the sludge flocs decreased with hydrolysis and acidification. The pH had a more significant influence on the dewaterability of sludge flocs than temperature. Sludge dewaterability during hydrolysis and acidification processes greatly deteriorated from 9.7 s at raw sludge to 340-450 s under alkaline conditions. However, it was just slightly increased under acidic conditions. Further investigation suggested that CST was affected by soluble PN, soluble PN/PS, and particle sizes of sludge flocs, but was affected slightly by total PN, PS, or PN/PS in the whole sludge flocs and other fractions （except slime）.

Effect of particle size on the microstructure and thermal conductivity of Al/diamond composites prepared by spark plasma sintering

Spark plasma sintering （SPS） was used to fabricate Al/diamond composites. The influence of diamond particle size on the microstructure and thermal conductivity （TC） of composites was investigated by combining experimental results with model prediction. The results show that both composites with 40 pan particles and 70 μm particles exhibit high density and good TC, and the composite with 70 μm particles indicates an excellent TC of 325 W.m^-1.K^-1. Their TCs lay between the theoretical estimated bounds. In contrast, the composite with 100 lain particles demonstrates low density as well as poor TC due to its high porosity and weak interfacial bonding. Its TC is even considerably less than the lower bound of the predicted value. Using larger diamond particles can further enhance thermal conductive performance only based on the premise that highly dense composites of strong interfacial bonding can be obtained.

Influences of Temperature and Coal Particle Size on the Flash Pyrolysis of Coal in a Fast-entrained Bed

The experiments on the flash pyrolysis of a lignite were carried out in a fast-entrained bed reactor as a basic study on a so-called ＇ coal topping process＇. The investigation focused on the effects of pyrolysis temperature and coal particle size on the product distribution and composition. The experimental results show that an increase in the pyrolysis temperature results in a higher yield of gaseous products while a larger particle size leads to a decrease of the liquid yield. An optimum temperature for the liquid yield was found to be 650℃. A certain amount of phenol groups was found in the liquid products, which may be used to produce high-valued fine chemicals. The FTIR analyses of the coal and chars show that aliphatic structures in the chars are gradually replaced by aromatic structures with the increasing of pyrolysis temperature and coal particle size. The results of this study provide fundamental data and optimal conditions to maximize light oils yields for the coal topping process.

Effects of fumaric acid supplementation on methane production and rumen fermentation in goats fed diets varying in forage and concentrate particle size

Background: In rumen fermentation, fumaric acid(FA) could competitively utilize hydrogen with methanogenesis to enhance propionate production and suppress methane emission, but both effects were diet-dependent. This study aimed to explore the effects of FA supplementation on methanogenesis and rumen fermentation in goats fed diets varying in forage and concentrate particle size.Methods: Four rumen-cannulated goats were used in a 4 × 4 Latin square design with a 2 × 2 factorial arrangement of treatments: low or high ratio of forage particle size: concentrate particle size(Fps:Cps), without or with FA supplementation(24 g/d). Fps:Cps was higher in the diet with chopped alfalfa hay plus ground corn than in that with ground alfalfa hay plus crushed corn.Results: Both increasing dietary Fps:Cps and FA supplementation shifted ruminal volatile fatty acid(VFA) patterns toward more propionate and less acetate in goats. An interaction between dietary Fps:Cps and FA supplementation was observed for the ratio of acetate to propionate(A:P), which was more predominant when FA was supplemented in the low-Fps:Cps diet. Methane production was reduced by FA, and the reduction was larger in the low-Fps:Cps diet(31.72%) than in the high-Fps:Cps diet(17.91%). Fumaric acid decreased ruminal total VFA concentration and increased ruminal p H. No difference was found in ruminal DM degradation of concentrate or alfalfa hay by dietary Fps:Cps or FA. Goats presented a lower ruminal methanogen abundance with FA supplementation and a higher B. fibrisolvens abundance with high dietary Fps:Cps.Conclusions: Adjusting dietary Fps:Cps is an alternative dietary model for studying diet-dependent effects without changing dietary chemical composition. Fumaric acid supplementation in the low-Fps:Cps diet showed greater responses in methane mitigation and propionate increase.

Distribution of Cu and Pb in particle size fractions of urban soils from different city zones of Nanjing, China

Soil samples from 4 defined city zones of Nanjing were randomly collected at 0-5 cm and 5-20 cm intervals and size fractions of soil particles were separated from undisturbed bulk soils by low energy dispersion procedure. The total contents of Cu and Pb in the different particle size fractions of the urban soils were analyzed by HNO3-HF-HClO4 digestion and flame atomic absorption spectrophotometer determination. The total content of Cu and Pb in soil particle size fractions varied with their size and with city zones as well. Both the content and variation with the size fractions of Pb was bigger than of Cu supporting our previous finding that there was Pb pollution to different degrees in the urban soils although the two elements were generally enriched in clay-sized fraction. Contaminated Pb tended to be preferentially enriched in the size fraction of 2000-250 μm and clay-sized fraction. While the size fractions of the soils from newly developed and preserved area contained smaller amount of Cu and Pb, the partitioning of them in coarse and fine particle size fractions were insignificant compared to that from inner residence and commercial area. The very high Pb level over 150 mg/kg of the fine particle fractions from the soils of the inner city could be a cause of high blood Pb level reported of children from the city as acute exposure to Pb of fine particles of the urban soil might occur by soil ingestion and inhalation by young children. Thus, much attention should be paid to the partitioning of toxic metals in fine soil particles of the urban soils and countermeasures against high health risk of Pb exposure by soil ingestion and dust inhalation should be practiced against the health problem of blood Pb for young children from the cities.

Leaching behavior of V,Pb,Cd,Cr,and As from stone coal waste rock with different particle sizes

This paper investigates the leaching behavior of heavy metals(V,Pb,Cd,Cr,and As) from stone coal waste rocks with various particle sizes using dynamic leaching experiments.The results show that the dissolved concentrations of V and As initially increased and then slightly decreased as time progressed and that the dissolved concentrations of Pb,Cd,and Cr were high in the early stage before decreasing.The particle size of the stone coal waste rocks strongly influenced the heavy metal concentration in the leaching solutions.The effects of the particle size of the stone coal waste rocks on the dissolved concentrations of V,Pb,and As decreased in the order fine fraction > medium fraction > coarse fraction,and the effects of particle size on the dissolved concentrations of Cr and Cd decreased in the order medium fraction > coarse fraction > fine fraction and coarse fraction > medium fraction > fine fraction,respectively.The quantities of heavy metals dissolved from the stone coal waste rock with fine particle sizes were observed to decrease in the order V(17104.36 μg/kg) > As(609.41 μg/kg) > Pb(469.24 μg/kg) > Cr(56.35 μg/kg) > Cd(27.52 μg/kg),and the dissolution rates decreased in the order As(2.96%) > Pb(0.93%) > V(0.35%) > Cd(0.25%) > Cr(0.01%).The specific surface area,pore size of the stone coal waste rocks,and chemical forms of heavy metals also influenced the release of heavy metals from the stone coal waste rocks.Kinetic analysis showed that the dissolution of heavy metals fundamentally agreed with the rate equation controlled by the shrinking core model.The results of this study are expected to serve as a reference for the evaluation of heavy metals contamination from stone coal waste rocks.