Optimization of Fixture Number in Large Thin-Walled Parts Assembly Based on IPSO

There are lots of researches on fixture layout optimization for large thin-walled parts.Current researches focus on the positioning problem,i.e.,optimizing the positions of a constant number of fixtures.However,how to determine the number of fixtures is ignored.In most cases,the number of fixtures located on large thin-walled parts is determined based on engineering experience,which leads to huge fixture number and extra waste.Therefore,this paper constructs an optimization model to minimize the number of fixtures.The constraints are set in the optimization model to ensure that the part deformation is within the surface profile tolerance.In addition,the assembly gap between two parts is also controlled.To conduct the optimization,this paper develops an improved particle swarm optimization(IPSO)algorithm by integrating the shrinkage factor and adaptive inertia weight.In the algorithm,particles are encoded according to the fixture position.Each dimension of the particle is assigned to a sub-region by constraining the optional position range of each fixture to improve the optimization efficiency.Finally,a case study on ship curved panel assembly is provided to prove that our method can optimize the number of fixtures while meeting the assembly quality requirements.This research proposes a method to optimize the number of fixtures,which can reduce the number of fixtures and achieve deformation control at the same time.

Development of Fixture Layout Optimization for Thin-Walled Parts:A Review

An increasing number of researchers have researched fixture layout optimization for thin-walled part assembly during the past decades.However,few papers systematically review these researches.By analyzing existing literature,this paper summarizes the process of fixture layout optimization and the methods applied.The process of optimization is made up of optimization objective setting,assembly variation/deformation modeling,and fixture layout optimization.This paper makes a review of the fixture layout for thin-walled parts according to these three steps.First,two different kinds of optimization objectives are introduced.Researchers usually consider in-plane variations or out-of-plane deformations when designing objectives.Then,modeling methods for assembly variation and deformation are divided into two categories:Mechanism-based and data-based methods.Several common methods are discussed respectively.After that,optimization algorithms are reviewed systematically.There are two kinds of optimization algorithms:Traditional nonlinear programming and heuristic algorithms.Finally,discussions on the current situation are provided.The research direction of fixture layout optimization in the future is discussed from three aspects:Objective setting,improving modeling accuracy and optimization algorithms.Also,a new research point for fixture layout optimization is discussed.This paper systematically reviews the research on fixture layout optimization for thin-walled parts,and provides a reference for future research in this field.

Discrimination of polysorbate 20 by high-performance liquid chromatography-charged aerosol detection and characterization for components by expanding compound database and library

Analyzing polysorbate 20(PS20)composition and the impact of each component on stability and safety is crucial due to formulation variations and individual tolerance.The similar structures and polarities of PS20 components make accurate separation,identification,and quantification challenging.In this work,a high-resolution quantitative method was developed using single-dimensional high-performance liquid chromatography(HPLC)with charged aerosol detection(CAD)to separate 18 key components with multiple esters.The separated components were characterized by ultra-high-performance liquid chromatography-quadrupole time-of-flight mass spectrometry(UHPLC-Q-TOF-MS)with an identical gradient as the HPLC-CAD analysis.The polysorbate compound database and library were expanded over 7-time compared to the commercial database.The method investigated differences in PS20 samples from various origins and grades for different dosage forms to evaluate the composition-process relationship.UHPLC-Q-TOF-MS identified 1329 to 1511 compounds in 4 batches of PS20 from different sources.The method observed the impact of 4 degradation conditions on peak components,identifying stable components and their tendencies to change.HPLC-CAD and UHPLC-Q-TOF-MS results provided insights into fingerprint differences,distinguishing quasi products.

基于Visual Components的套筒类零件柔性制造单元的应用研究

为实现多品种中、小批量零件的智能化加工,以套筒类零件加工为研究对象,通过对零件工艺的分析,为满足单元加工、搬运、翻转等功能需求,对数控机床和工业机器人进行选型,实现柔性制造单元的设计。利用Visual Components软件进行单元搭建、仿真优化反馈以提高真实产线运行效率。利用Profinet实现制造单元真实搭建,完成单元安装调试。套筒类零件柔性制造单元的设计为生产线设计提供了新思路。

Multi-omics analyses provide insights into the evolutionary history and the synthesis of medicinal components of the Chinese wingnut

Chinese wingnut(Pterocarya stenoptera)is a medicinally and economically important tree species within the family Juglandaceae.However,the lack of high-quality reference genome has hindered its in-depth research.In this study,we successfully assembled its chromosome-level genome and performed multiomics analyses to address its evolutionary history and synthesis of medicinal components.A thorough examination of genomes has uncovered a significant expansion in the Lateral Organ Boundaries Domain gene family among the winged group in Juglandaceae.This notable increase may be attributed to their frequent exposure to flood-prone environments.After further differentiation between Chinese wingnut and Cyclocarya paliurus,significant positive selection occurred on the genes of NADH dehydrogenase related to mitochondrial aerobic respiration in Chinese wingnut,enhancing its ability to cope with waterlogging stress.Comparative genomic analysis revealed Chinese wingnut evolved more unique genes related to arginine synthesis,potentially endowing it with a higher capacity to purify nutrient-rich water bodies.Expansion of terpene synthase families enables the production of increased quantities of terpenoid volatiles,potentially serving as an evolved defense mechanism against herbivorous insects.Through combined transcriptomic and metabolomic analysis,we identified the candidate genes involved in the synthesis of terpenoid volatiles.Our study offers essential genetic resources for Chinese wingnut,unveiling its evolutionary history and identifying key genes linked to the production of terpenoid volatiles.

Effect of Planting Date on Yield and Yield Components of Grain Sorghum Hybrids

In Kansas, productivity of grain sorghum [Sorghum bicolor (L.) Moench] is affected by weather conditions at planting and during pollination. Planting date management and selection of hybrid maturity group can help to avoid severe environmental stresses during these sensitive stages. The hypothesis of the study was that late May planting improves grain sorghum yield and yield components compared with late June planting. The objectives of this research were to investigate the influence of planting dates yield and yield components of different grain sorghum hybrids, and to determine the optimal planting date and hybrid combination for maximum biomass and grains production. Three sorghum hybrids (early, medium, and late maturing) were planted in late May and late June without irrigation in Kansas at Manhattan/Ashland Bottom Research Station, and Hutchinson in 2010;and at Manhattan/North Farm and Hutchinson in 2011. Data on dry matter production, yield and yield components were collected. Grain yield and yield components were influenced by planting date depending on environmental conditions. At Manhattan (2010), greater grain yield, number of heads per plant, were obtained with late-June planting compared with late May planting, while at Hutchinson (2010) greater yield was obtained with late May planting for all hybrids. The yield component most affected at Hutchinson was the number of kernels∙panicle−1 and plant density. Late-May planting was favorable for late maturing hybrid (P84G62) in all locations. However, the yield of early maturing hybrid (DKS 28-05) and medium maturing hybrid (DKS 37-07) was less affected by delayed planting. The effects of planting dates on yield and yield components of grain sorghum hybrids were found to be variable among hybrid maturity groups and locations.

Simultaneous purification of minor components in natural products using twin-column recycling chromatography with a step solvent gradient

The isolation of minor components from complex natural product matrices presents a significant challenge in the field of purification science due to their low concentrations and the presence of structurally similar compounds.This study introduces an optimized twin-column recycling chromatography method for the efficient and simultaneous purification of these elusive constituents.By introducing water at a small flowing rate between the twin columns,a step solvent gradient is created,by which the leading edge of concentration band would migrate at a slower rate than the trailing edge as it flowing from the upstream to downstream column.Hence,the band broadening is counterbalanced,resulting in an enrichment effect for those minor components in separation process.Herein,two target substances,which showed similar peak position in high performance liquid chromatography(HPLC)and did not exceed 1.8%in crude paclitaxel were selected as target compounds for separation.By using the twin-column recycling chromatography with a step solvent gradient,a successful purification was achieved in getting the two with the purity almost 100%.We suggest this method is suitable for the separation of most components in natural produces,which shows higher precision and recovery rate compared with the common lab-operated separation ways for natural products(thin-layer chromatography and prep-HPLC).

Nontraditional energy-assisted mechanical machining of difficult-to-cut materials and components in aerospace community:a comparative analysis

The aerospace community widely uses difficult-to-cut materials,such as titanium alloys,high-temperature alloys,metal/ceramic/polymer matrix composites,hard and brittle materials,and geometrically complex components,such as thin-walled structures,microchannels,and complex surfaces.Mechanical machining is the main material removal process for the vast majority of aerospace components.However,many problems exist,including severe and rapid tool wear,low machining efficiency,and poor surface integrity.Nontraditional energy-assisted mechanical machining is a hybrid process that uses nontraditional energies(vibration,laser,electricity,etc)to improve the machinability of local materials and decrease the burden of mechanical machining.This provides a feasible and promising method to improve the material removal rate and surface quality,reduce process forces,and prolong tool life.However,systematic reviews of this technology are lacking with respect to the current research status and development direction.This paper reviews the recent progress in the nontraditional energy-assisted mechanical machining of difficult-to-cut materials and components in the aerospace community.In addition,this paper focuses on the processing principles,material responses under nontraditional energy,resultant forces and temperatures,material removal mechanisms,and applications of these processes,including vibration-,laser-,electric-,magnetic-,chemical-,advanced coolant-,and hybrid nontraditional energy-assisted mechanical machining.Finally,a comprehensive summary of the principles,advantages,and limitations of each hybrid process is provided,and future perspectives on forward design,device development,and sustainability of nontraditional energy-assisted mechanical machining processes are discussed.

Transcriptomic analysis of Andrias davidianus meat and experimental validation for exploring its bioactive components as functional foods

Andrias davidianus(Chinese giant salamander,CGS)is the largest and oldest extant amphibian species in the world and is a source of prospective functional food in China.However,the progress of functional peptides mining was slow due to lack of reference genome and protein sequence data.In this study,we illustrated full-length transcriptome sequencing to interpret the proteome of CGS meat and obtain 10703 coding DNA sequences.By functional annotation and amino acid composition analysis,we have discovered various genes related to signal transduction,and 16 genes related to longevity.We have also found vast variety of functional peptides through protein coding sequence(CDS)analysis by comparing the data obtained with the functional peptide database.Val-Pro-Ile predicted by the CDS analysis was released from the CGS meat through enzymatic hydrolysis,suggesting that our approach is reliable.This study suggested that transcriptomic analysis can be used as a reference to guide polypeptide mining in CGS meat,thereby providing a powerful mining strategy for the bioresources with unknown genomic and proteomic sequences.

A Systematic Review of Computer Vision Techniques for Quality Control in End-of-Line Visual Inspection of Antenna Parts

The rapid evolution of wireless communication technologies has underscored the critical role of antennas in ensuring seamless connectivity.Antenna defects,ranging from manufacturing imperfections to environmental wear,pose significant challenges to the reliability and performance of communication systems.This review paper navigates the landscape of antenna defect detection,emphasizing the need for a nuanced understanding of various defect types and the associated challenges in visual detection.This review paper serves as a valuable resource for researchers,engineers,and practitioners engaged in the design and maintenance of communication systems.The insights presented here pave the way for enhanced reliability in antenna systems through targeted defect detection measures.In this study,a comprehensive literature analysis on computer vision algorithms that are employed in end-of-line visual inspection of antenna parts is presented.The PRISMA principles will be followed throughout the review,and its goals are to provide a summary of recent research,identify relevant computer vision techniques,and evaluate how effective these techniques are in discovering defects during inspections.It contains articles from scholarly journals as well as papers presented at conferences up until June 2023.This research utilized search phrases that were relevant,and papers were chosen based on whether or not they met certain inclusion and exclusion criteria.In this study,several different computer vision approaches,such as feature extraction and defect classification,are broken down and analyzed.Additionally,their applicability and performance are discussed.The review highlights the significance of utilizing a wide variety of datasets and measurement criteria.The findings of this study add to the existing body of knowledge and point researchers in the direction of promising new areas of investigation,such as real-time inspection systems and multispectral imaging.This review,on its whole,offers a complete study of computer vision approaches for quality control in antenna parts.It does so by providing helpful insights and drawing attention to areas that require additional exploration.

Umami taste components in chicken-spices blends and potential effect of aroma on umami taste intensity

In this study,umami taste intensity(UTI)and umami taste components in chicken breast(CB)and chickenspices blends were characterized using sensory and instrumental analysis.Our main objective was to assess the aroma-umami taste interactions in different food matrices and reconcile the aroma-taste perception to assist future product development.The impact of key aroma,including vegetable-note"2-pentylfuran",meaty"methional",green"hexanal",and spicy-note-estragole and caryophyllene"on UTI was evaluated in monosodium glutamate and chicken extract.We found that spices significantly decreased UTI and umami taste components in CB.Interestingly,the perceptually similar odorants and tastants exhibited the potential to enhance UTI in food matrices.Methional was able to increase the UTI,whereas spicy and green-note components could reduce the UTI significantly.This information would be valuable to food engineers and formulators in aroma selection to control the UTI perceived by consumers,thus,improving the quality and acceptability of the chicken products.

Association of complement components with risk of colorectal cancer:A systematic review and meta-analysis

BACKGROUND Complement components could contribute to the tumor microenvironment and the systemic immune response.Nevertheless,their role in colorectal cancer(CRC)remains a contentious subject.AIM To elucidate the relationship between complement components and CRC risk and clinical characteristics.METHODS Searches were conducted in PubMed,the Cochrane Library,and the China National Knowledge Infrastructure database until June 1,2023.We included cohort studies encompassing participants aged≥18 years,investigating the association between complement components and CRC.The studies were of moderate quality or above,as determined by the Agency for Healthcare Research and Quality.The meta-analysis employed fixed-effects or random-effects models based on the I^(2)test,utilizing risk ratio(RR)and their corresponding 95%confidence interval(CI)for outcomes.Sensitivity and subgroup analyses were performed to validate the robustness of the collective estimates and identify the source of heterogeneity.RESULTS Data from 15 studies,comprising 1631 participants that met the inclusion criteria,were included in the meta-analysis.Our findings indicated that protein levels of cluster of differentiation 46(CD46)(RR=3.66,95%CI:1.75-7.64,P<0.001),CD59(RR=2.86,95%CI:1.36-6.01,P=0.005),and component 1(C1)(RR=5.88,95%CI:1.75-19.73,P=0.004)and serum levels of C3(standardized mean difference=1.82,95%CI:0.06-3.58,P=0.040)were significantly elevated in patients with CRC compared to healthy controls.Strong expression of CD55 or CD59 was associated with a higher incidence of lymph node metastasis,whereas strong CD46 expression correlated with a higher incidence of tumor differentiation compared to low CD46 expression(P<0.05 for all).Although specific pooled results demonstrated notable heterogeneity,subgroup analyses pointed to regional differences as the primary source of inconsistency among the studies.CONCLUSION Our analysis underscores that increased levels of specific complement components are associated with a heightened risk of CRC,emphasizing the potential significance of monitoring elevated complement component levels.

A novel approach of jet polishing for interior surface of small-grooved components using three developed setups

It is a challenge to polish the interior surface of an additively manufactured component with complex structures and groove sizes less than 1 mm.Traditional polishing methods are disabled to polish the component,meanwhile keeping the structure intact.To overcome this challenge,small-grooved components made of aluminum alloy with sizes less than 1 mm were fabricated by a custom-made printer.A novel approach to multi-phase jet(MPJ)polishing is proposed,utilizing a self-developed polisher that incorporates solid,liquid,and gas phases.In contrast,abrasive air jet(AAJ)polishing is recommended,employing a customized polisher that combines solid and gas phases.After jet polishing,surface roughness(Sa)on the interior surface of grooves decreases from pristine 8.596μm to 0.701μm and 0.336μm via AAJ polishing and MPJ polishing,respectively,and Sa reduces 92%and 96%,correspondingly.Furthermore,a formula defining the relationship between linear energy density and unit defect volume has been developed.The optimized parameters in additive manufacturing are that linear energy density varies from 0.135 J mm^(-1)to 0.22 J mm^(-1).The unit area defect volume achieved via the optimized parameters decreases to 1/12 of that achieved via non-optimized ones.Computational fluid dynamics simulation results reveal that material is removed by shear stress,and the alumina abrasives experience multiple collisions with the defects on the heat pipe groove,resulting in uniform material removal.This is in good agreement with the experimental results.The novel proposed setups,approach,and findings provide new insights into manufacturing complex-structured components,polishing the small-grooved structure,and keeping it unbroken.

The bio-active components of the Mongolian medicine Horcha-6 and therapeutic mechanism in the rat migraine model

Background:The active components of Horcha-6 were identified using liquid chromatography with tandem mass spectrometry.Also,we investigated the potential mechanisms that explain why Horcha-6 may be effective in treating migraines through the use of network pharmacology and a rat migraine model.Methods:After identifying the active components of Horcha-6,the corresponding genes of the active components’target were obtained from the Universal Protein database,and a“compound-target-disease”network was constructed using Cytoscape 3.9.0 software.For the in vivo experiments,nitroglycerin was injected intraperitoneally into rats to create a migraine model.Pre-treatment with Horcha-6 was administered orally for 14 days,and rats were subjected to migraine-related behavior tests.RNA sequencing was performed to identify the gene expression regulated by Horcha-6 in the trigeminal nerve.Results:A total of 903 chemical components of Horcha-6 have been collected in the liquid chromatography with tandem mass spectrometry.We discovered 55 of the Horcha-6 bio-active components that were evaluated based on their Percent Human Oral Absorption(≥30%)and DL values(≥0.185)on the traditional Chinese medicine systems pharmacology database.The“compound-target-disease”network contained 163 intersection targets with the migraine state.Gene Ontology analysis indicated that these components significantly regulated the immune response,vascular function,oxidative stress,etc.When Kyoto Encyclopedia of Genes and Genomes enrichment analysis was performed,we observed that most of the target genes were significantly enriched in the inflammation and neuro-related signaling pathway,toll-like receptor signaling pathway,neuroactive ligand-receptor interaction,etc.These predictions were further demonstrated via in vivo animal model experiments.The RNA sequencing results showed that 41 genes were down-regulated(P<0.05)and 86 genes were up-regulated(P<0.05)in the Horcha-6 treated group compared with the untreated group.Those genes were mainly involved in neuromodulation,vascular function,and hormone metabolism.Conclusion:The 55 bio-active components in Horcha-6 regulate inflammation,hormone metabolism,and neurotransmitters and have potential as a therapy to treat migraines.

GC-MS Analysis of Chemical Components of Volatile Oil in Different Parts of Fennel( Foenicuzu vulgare Mill. )

[Objectives] This study was conducted to analyze the composition of volatile oil in different parts of fennel(Foenicuzu vulgare Mill.) and to compare the differences in the composition of volatile oil in different parts of fennel.[Methods]The steam distillation method was applied to extract volatile oil from different parts of fennel,and the components of volatile oil from different parts of fennel were separated and identified by GC-MS.The relative content of each component was determined by the peak area normalization method.[Results]37,33,18,and 44 chemical components were separated from the volatile oil of fennel roots,stems,young leaves and fruit,respectively,accounting for 98.64%,99.34%,99.59% and 95.99% of the total volatile oil of corresponding parts.A total of 77 chemical components were identified in the four parts,of which 5 were common components.The main component of the volatile oil in the stems and young leaves was trans-anethole.The main components of the volatile oil in fruit were estragole and trans-anethole.And the main component of the volatile oil in the roots was dill apiol.The components in the volatile oil of fennel roots,stems,young leaves and fruit were different in type and content.[Conclusions]This study provides a theoretical reference for the further effective development and utilization of fennel resources.

HS-SPME-GC-MS Analysis on Volatile Components in Different Cultivars and Different Parts of Artemisia argyi

[Objectives] To analyze and compare the difference in volatile components of different cultivars and different parts of Artemisia argyi by using headspace solid phase microextraction( HS-SPME) and provide scientific basis for comprehensive development and rational utilization of Artemisia argyi. [Methods]Firstly,HS-SPME was used to extract the volatile components from the leaves,seeds,and stems of seven-tip Artemisia argyi,five-tip Artemisia argyi,and golden Artemisia argyi. Their chemical composition was analyzed by gas chromatographymass spectrometry( GC-MS),and the relative mass fraction of each component was determined by area normalization method. [Results] For the same variety of Artemisia argyi,the content of volatile components in leaves was higher than in seeds and stems except camphor,and the content of volatile components in seven-tip Artemisia argyi leaves was higher than in five-tip Artemisia argyi and golden Artemisia argyi leaves.HS-SPME-GC-MS analysis showed that eucalyptol,camphor,thujone,α-pinene,1-caryophyllene and caryophyllene oxide with higher content were detected in different parts of the different cultivars of Artemisia argyi. [Conclusions]Seven-tip Artemisia argyi leaves were the best medicinal parts of the three cultivars,followed by seven-tip Artemisia argyi seeds.

Analysis of Volatile Components in Different Parts of Polygala japonica Houtt.

[Objectives] To analyze the volatile components in different parts of Polygala japonica Houtt. and compare the differences of these volatile components. [Methods] The volatile components in different parts of P. japonica Houtt. were analyzed by the headspace solid-phase microextraction( HS-SPME) combined with GC-MS,and the relative percentage of each component was determined by peak area normalization. [Results] Thirty kinds of volatile components were identified from the leaves and rhizomes of P. japonica Houtt.,mainly including olefins,aromatic hydrocarbons,alkanes and esters. [Conclusions] The volatile components in different parts of P. japonica Houtt. were different,and there may be difference in the medicinal value of volatile components in different parts,thus it is required to take an overall consideration of these differences in the development and utilization of P. japonica Houtt.

Shanghai Car Parts and Components Industry

Shanghai Santana cars had produced a total of 270,000 cars by the end of 1993, and undergone SKD, CKD and localization stages. The car industry will soon become a pillar industry in Shanghai. During its development, the Shanghai car industry has always given special attention to localization, thus the localization rate of car parts and components has increased year by year. In 1988, Shanghai Santanacars produced 15,000 units, with 13,08 percent of

Research on the Comparison between the Different Policies by Service Level and Inventory Level Performance of Auto Parts in N.A.C.C.(North Automobile Components Company)

As after sales services become more and more popular,particularly preven­tive or corrective maintenance,the intervention and repair of the custom­er’s goods in a timely and efficient manner ensure customer satisfaction and contribute to the establishment of brand image in the market of the suppliers.The availability and quality of spare parts are key elements of this strategy while ensuring minimal management costs.The reuse of spare parts retrieved from customer systems is a growing maintenance strategy practice which impacts the traditional spare parts supply chain.This reuse is primarily driven by extending the economic life of goods,initially re­garded as waste and therefore without added value,by transforming them into valuable spare parts that can be reused;secondly,for environmental or regulatory reasons,demanding responsibility for the treatment of products at the end of their life;and thirdly,to improve the availability of parts for maintenance,especially parts that the organization can no longer purchase or that are impacted by other issues.It also involves the analysis of their condition and their eventual return to working order as they are retrieved from the customer’s systems in a defective condition.In this paper,we will identify and classify the different customers and spare parts by estimating the critical level of rationing policy based on forecasts,identify the thresh­olds of inventory management policies,and finally,compare the different policies by service level and inventory level performance for the N.A.C.C.company.

Leveraging React Components in Business Process Management (BPM) Applications

As organizations increasingly embrace digital transformation, the integration of modern web technologies like React.js with Business Process Management (BPM) applications has become essential. React components offer flexibility, reusability, and scalability, making them ideal for enhancing user interfaces and driving user engagement within BPM environments. This article explores the benefits, challenges, and best practices of leveraging React components in BPM applications, along with real-world examples of successful implementations.