Memristors as non-volatile memory devices have gained numerous attentions owing to their advantages in storage,in-memory computing, synaptic applications, etc. In recent years, two-dimensional(2D) materials with moder...Memristors as non-volatile memory devices have gained numerous attentions owing to their advantages in storage,in-memory computing, synaptic applications, etc. In recent years, two-dimensional(2D) materials with moderate defects have been discovered to exist memristive feature. However, it is very difficult to obtain moderate defect degree in 2D materials, and studied on modulation means and mechanism becomes urgent and essential. In this work, we realized memristive feature with a bipolar switching and a configurable on/off ratio in a two-terminal MoS_(2) device(on/off ratio ~100), for the first time, from absent to present using laser-modulation to few-layer defect-free MoS_(2)(about 10 layers), and its retention time in both high resistance state and low resistance state can reach 2×10^(4) s. The mechanism of the laser-induced memristive feature has been cleared by dynamic Monte Carlo simulations and first-principles calculations. Furthermore, we verified the universality of the laser-modulation by investigating other 2D materials of TMDs. Our work will open a route to modulate and optimize the performance of 2D semiconductor memristive devices.展开更多
Constructing robust surface and bulk structure is the prerequisite for realizing high performance high voltage LiCoO_(2)(LCO).Herein,we manage to synthesize a surface Mg-doping and bulk Al-doping coreshell structured ...Constructing robust surface and bulk structure is the prerequisite for realizing high performance high voltage LiCoO_(2)(LCO).Herein,we manage to synthesize a surface Mg-doping and bulk Al-doping coreshell structured LCO,which demonstrates excellent cycling performance.Half-cell shows 94.2%capacity retention after 100 cycles at 3.0-4.6 V(vs.Li/Li^(+))cycling,and no capacity decay after 300 cycles for fullcell test(3.0-4.55 V).Based on comprehensive microanalysis and theoretical calculations,the degradation mechanisms and doping effects are systematically revealed.For the undoped LCO,high voltage cycling induces severe interfacial and bulk degradations,where cracks,stripe defects,fatigue H2 phase,and spinel phase are identified in grain bulk.For the doped LCO,Mg-doped surface shell can suppress the interfacial degradations,which not only stabilizes the surface structure by forming a thin rock-salt layer but also significantly improves the electronic conductivity,thus enabling superior rate performance.Bulk Al-doping can suppress the lattice"breathing"effect and the detrimental H3 to H1-3 phase transition,which minimizes the internal strain and defects growth,maintaining the layered structure after prolonged cycling.Combining theoretical calculations,this work deepens our understanding of the doping effects of Mg and Al,which is valuable in guiding the future material design of high voltage LCO.展开更多
It is highly desirable to enhance the long-term stability of perovskite solar cells(PSCs)so that this class of photovoltaic cells can be effectively used for the commercialization purposes.In this contribution,attempt...It is highly desirable to enhance the long-term stability of perovskite solar cells(PSCs)so that this class of photovoltaic cells can be effectively used for the commercialization purposes.In this contribution,attempts have been made to use the two-step sequential method to dope EuBr_(2)into FAMAPbI_(3)perovskite to promote the stability.It is shown that the device durability at 85℃in air with RH of 20%-40%is improved substantially,and simultaneously the champion device efficiency of 23.04%is achieved.The enhancement in stability is attributed to two points:(ⅰ)EuBr_(2)doping effectively inhibits the decomposition andα-δphase transition of perovskite under ambient environment,and(ⅱ)EuBr_(2)aggregates in the oxidized format of Eu(BrO_(3))_(3)at perovskite grain boundaries and surface,hampering humidity erosion and mitigates degradation through coordination with H_(2)O.展开更多
To improve the electrocatalytic transformation of carbon dioxide (CO_(2)) to multi-carbon (C_(2+)) products is of great importance.Here we developed a nitrogen-doped Cu catalyst,by which the maximum C_(2+) Faradaic ef...To improve the electrocatalytic transformation of carbon dioxide (CO_(2)) to multi-carbon (C_(2+)) products is of great importance.Here we developed a nitrogen-doped Cu catalyst,by which the maximum C_(2+) Faradaic efficiency can reach 72.7%in flow-cell system,with the partial current density reaching 0.62 A cm^(-2).The in situ Raman spectra demonstrate that the *CO adsorption can be strengthened on such a N-doped Cu catalyst,thus promoting the *CO utilization in the subsequent C–C coupling step.Simultaneously,the water activation can be well enhanced by N doping on Cu catalyst.Owing to the synergistic effects,the selectivity and activity for C_(2+) products over the N-deoped Cu catalyst are much improved.展开更多
To demonstrate flexible and tandem device applications,a low-temperature Cu_(2)ZnSnSe_(4)(CZTSe)deposition process,combined with efficient alkali doping,was developed.First,high-quality CZTSe films were grown at 480℃...To demonstrate flexible and tandem device applications,a low-temperature Cu_(2)ZnSnSe_(4)(CZTSe)deposition process,combined with efficient alkali doping,was developed.First,high-quality CZTSe films were grown at 480℃by a single co-evaporation,which is applicable to polyimide(PI)substrate.Because of the alkali-free substrate,Na and K alkali doping were systematically studied and optimized to precisely control the alkali distribution in CZTSe.The bulk defect density was significantly reduced by suppression of deep acceptor states after the(NaF+KF)PDTs.Through the low-temperature deposition with(NaF+KF)PDTs,the CZTSe device on glass yields the best efficiency of 8.1%with an improved Voc deficit of 646 mV.The developed deposition technologies have been applied to PI.For the first time,we report the highest efficiency of 6.92%for flexible CZTSe solar cells on PI.Additionally,CZTSe devices were utilized as bottom cells to fabricate four-terminal CZTSe/perovskite tandem cells because of a low bandgap of CZTSe(~1.0 eV)so that the tandem cell yielded an efficiency of 20%.The obtained results show that CZTSe solar cells prepared by a low-temperature process with in-situ alkali doping can be utilized for flexible thin-film solar cells as well as tandem device applications.展开更多
The low energy density,unsatisfied cycling performance,potential safety issue and slow charging kinetics of the commercial lithium-ion batteries restrained their further application in the fields of fast charging and ...The low energy density,unsatisfied cycling performance,potential safety issue and slow charging kinetics of the commercial lithium-ion batteries restrained their further application in the fields of fast charging and long-haul electric vehicles.Monoclinic TiNb_(2)O_(7)(TNO)with the theoretical capacity of 387 mAh g^(-1)has been proposed as a high-capacity anode materials to replace Li4Ti5O12.In this work,homovalent doping strategy was used to enhance the electrochemical performance of TiNb_(2)O_(7)(TNO)by employing Zr to partial substitute Ti through solvothermal method.The doping of Zr^(4+)ions can enlarge the lattice structure without changing the chemical valence of the original elements,refine and homogenize the grains,improve the electrical conductivity,and accelerate the ion diffusion kinetics,and finally enhance the cycle and rate performance.Specifically,Z0.05-TNO shows initial discharge capacity of as high as 312.2 mAh g^(-1)at 1 C and 244.8 mAh g^(-1)at 10 C,and still maintains a high specific capacity of 171.3 mAh g^(-1)after 800 cycles at 10 C.This study provides a new strategy for high-performance fast-charging energy storage electrodes.展开更多
Potassium-ion batteries(PIBs)offer a cost-effective and resource-abundant solution for large-scale energy storage.However,the progress of PIBs is impeded by the lack of high-capacity,long-life,and fast-kinetics anode ...Potassium-ion batteries(PIBs)offer a cost-effective and resource-abundant solution for large-scale energy storage.However,the progress of PIBs is impeded by the lack of high-capacity,long-life,and fast-kinetics anode electrode materials.Here,we propose a dual synergic optimization strategy to enhance the K^(+)storage stability and reaction kinetics of Bi_(2)S_(3) through two-dimensional compositing and cation doping.Externally,Bi_(2)S_(3) nanoparticles are loaded onto the surface of three-dimensional interconnected Ti_(3)C_(2)T_(x) nanosheets to stabilize the electrode structure.Internally,Cu^(2+)doping acts as active sites to accelerate K^(+)storage kinetics.Various theoretical simulations and ex situ techniques are used to elucidate the external–internal dual synergism.During discharge,Ti_(3)C_(2)T_(x) and Cu^(2+)collaboratively facilitate K+intercalation.Subsequently,Cu^(2+)doping primarily promotes the fracture of Bi2S3 bonds,facilitating a conversion reaction.Throughout cycling,the Ti_(3)C_(2)T_(x) composite structure and Cu^(2+)doping sustain functionality.The resulting Cu^(2+)-doped Bi2S3 anchored on Ti_(3)C_(2)T_(x)(C-BT)shows excellent rate capability(600 mAh g^(-1) at 0.1 A g^(–1);105 mAh g^(-1) at 5.0 A g^(-1))and cycling performance(91 mAh g^(-1) at 5.0 A g^(-1) after 1000 cycles)in half cells and a high energy density(179 Wh kg–1)in full cells.展开更多
Li3V2-2/3xMnx（PO4）3（0≤x≤0.12） powders were synthesized by sol-gel method. The effect of Mn2＋-doping on the structure and electrochemical performances of Li3V2（PO4）3/C was characterized by XRD, SEM, XPS, galva...Li3V2-2/3xMnx（PO4）3（0≤x≤0.12） powders were synthesized by sol-gel method. The effect of Mn2＋-doping on the structure and electrochemical performances of Li3V2（PO4）3/C was characterized by XRD, SEM, XPS, galvanostatic charge /discharge and electrochemical impedance spectroscopy（EIS）. The XRD study shows that a small amount of Mn2＋-doped does not alter the structure of Li3V2（PO4）3/C materials, and all Mn2＋-doped samples are of pure single phase with a monoclinic structure （space group P21/n）. The XPS analysis indicates that valences state of V and Mn are ＋3 and ＋2 in Li3V1.94Mn0.09（PO4）3/C, respectively, and the citric acid in raw materials was decomposed into carbon during calcination, and residual carbon exists in Li3V1.94Mn0.09（PO4）/C. The results of electrochemical measurements show that Mn2＋-doping can improve the cyclic stability and rate performance of these cathode materials. The Li3V1.94Mn0.09（PO4）3/C cathode material shows the best cyclic stability and rate performance. For example, at the discharge current density of 40 mA/g, after 100 cycles, the discharge capacity of Li3V1.94Mn0.09（PO4）3/C declines from initial 158.8 mA·h/g to 120.5 mA·h/g with a capacity retention of 75.9%; however, that of the Mn-undoed sample declines from 164.2 mA·h/g to 72.6 mA·h/g with a capacity retention of 44.2%. When the discharge current is increased up to 1C, the intial discharge capacity of Li3V1.94Mn0.09（PO4）3/C still reaches 146.4 mA·h/g, and the discharge capacity maintains at 107.5 mA·h/g after 100 cycles. The EIS measurement indicates that Mn2＋-doping with a appropriate amount of Mn2＋ decreases the charge transfer resistance, which is favorable for the insertion/extraction of Li＋.展开更多
Using density functional theory, we studied band structure, density of states, optical proper- ties and Mulliken population of the pure and SiN doped BaMgAl10017：Eu^2＋ （BAM：Eu^2＋） phosphors. Calculation results ...Using density functional theory, we studied band structure, density of states, optical proper- ties and Mulliken population of the pure and SiN doped BaMgAl10017：Eu^2＋ （BAM：Eu^2＋） phosphors. Calculation results showed that the bands of BAM：Eu2＋ were of low band energy dispersion, indicating large joint density of states, hence high performance of optical absorption and luminescence. BAM：Eu^2＋ showed stronger absorption intensity while Eu^2＋ occupied the BR sites instead of the mO sites. The concentration of Eu^2＋ at BR sites increased while that at mO sites decreased after Si-N doping. The influence of the variation of Eu^2＋ distribution on the spectra was stronger than the influence of the decrease of Eu^2＋ PDOS when SiN concentration was lower than 0.25, therefore the absorption and luminescence intensity of BAM：Eu^2＋ were enhanced. Mulliken population of Si-N bond was higher than A1-O bond, while that of Eu-N bond was higher than Eu-O bond as well, indicating that Si-N bonds and Eu-N bonds possessed higher covalence than Al-O bonds and Eu-N bonds respectively. The existence of Si-N bonds and Eu-N bonds enhanced the local covalence of Eu^2＋, hence the optical stability of BAM：Eu^2＋.展开更多
CeO2-ZrO2-MnOx mixed oxide series were prepared by sol-gel method. CO pulse and CO-O2 cycle measurements were carried out to examine the oxygen storage complete capacity （OSCC） and dynamic oxygen storage capacity （...CeO2-ZrO2-MnOx mixed oxide series were prepared by sol-gel method. CO pulse and CO-O2 cycle measurements were carried out to examine the oxygen storage complete capacity （OSCC） and dynamic oxygen storage capacity （OSC） of the samples. The doping method brought about strong interactions between manganese oxide and ceria, both in the bulk and on the surface. Only a small part of Mn cations are incorporated into the ceria lattice to form solid solutions and the remaining are left on the surface as finely dispersed Mn3O4. The OSC behaviors of the materials are influenced by the doping amount of Mn and the solubility of Mn in the CeO2 lattice. The OSC is more easily affected by available contents of oxygen storage components when the measurement frequency is low. Comparatively, the concentration of lattice defects, which affects the mobility of bulk oxygen, is the determining factor under high frequency.展开更多
Ultrathin TiO_(2)nanosheets with coexposed{001}/{101}facets have attracted considerable attention because of their high photocatalytic activity.However,the charge-separated states in the TiO_(2)nanosheets must be exte...Ultrathin TiO_(2)nanosheets with coexposed{001}/{101}facets have attracted considerable attention because of their high photocatalytic activity.However,the charge-separated states in the TiO_(2)nanosheets must be extended to further enhance their photocatalytic activity for H_(2)evolution.Herein,we present a successful attempt to selectively dope lanthanide ions into the{101}facets of ultrathin TiO_(2)nanosheets with coexposed{001}/{101}facets through a facile one-step solvothermal method.The lanthanide doping slightly extended the light-harvesting region and markedly improved the charge-separated states of the TiO_(2)nanosheets as evidenced by UV-vis absorption and steady-state/transient photoluminescence spectra.Upon simulated sunlight irradiation,we observed a 4.2-fold enhancement in the photocatalytic H_(2)evolution activity of optimal Yb^(3+)-doped TiO_(2)nanosheets compared to that of their undoped counterparts.Furthermore,when Pt nanoparticles were used as cocatalysts to reduce the H_(2)overpotential in this system,the photocatalytic activity enhancement factor increased to 8.5.By combining these results with those of control experiments,we confirmed that the extended charge-separated states play the main role in the enhancement of the photocatalytic H_(2)evolution activity of lanthanide-doped TiO_(2)nanosheets with coexposed{001}/{101}facets.展开更多
A series of V2O5‐WO3/TiO2‐ZrO2,V2O5‐WO3/TiO2‐CeO2,and V2O5‐WO3/TiO2‐CeO2‐ZrO2 catalysts were synthesized to improve the selective catalytic reduction(SCR)performance and the K‐poisoning resistance of a V2O5‐W...A series of V2O5‐WO3/TiO2‐ZrO2,V2O5‐WO3/TiO2‐CeO2,and V2O5‐WO3/TiO2‐CeO2‐ZrO2 catalysts were synthesized to improve the selective catalytic reduction(SCR)performance and the K‐poisoning resistance of a V2O5‐WO3/TiO2 catalyst.The physicochemical properties were investigated by using XRD,BET,NH3‐TPD,H2‐TPR,and XPS,and the catalytic performance and K‐poisoning resistance were evaluated via a NH3‐SCR model reaction.Ce^4+and Zr^4+co‐doping were found to enhance the conversion of NOx,and exhibit the best K‐poisoning resistance owing to the largest BET‐specific surface area,pore volume,and total acid site concentration,as well as the minimal effects on the surface acidity and redox ability from K poisoning.The V2O5‐WO3/TiO2‐CeO2‐ZrO2 catalyst also presents outstanding H2O+SO2 tolerance.Finally,the in situ DRIFTS reveals that the NH3‐SCR reaction over the V2O5‐WO3/TiO2‐CeO2‐ZrO2 catalyst follows an L‐H mechanism,and that K poisoning does not change the reaction mechanism.展开更多
Inefficient charge separation and limited light absorption are two critical issues associated with high‐efficiency photocatalytic H2production using TiO2.Surface defects within a certain concentration range in photoc...Inefficient charge separation and limited light absorption are two critical issues associated with high‐efficiency photocatalytic H2production using TiO2.Surface defects within a certain concentration range in photocatalyst materials are beneficial for photocatalytic activity.In this study,surface defects(oxygen vacancies and metal cation replacement defects)were induced with a facile and effective approach by surface doping with low‐cost transition metals(Co,Ni,Cu,and Mn)on ultrafine TiO2.The obtained surface‐defective TiO2exhibited a3–4‐fold improved activity compared to that of the original ultrafine TiO2.In addition,a H2production rate of3.4μmol/h was obtained using visible light(λ>420nm)irradiation.The apparent quantum yield(AQY)at365nm reached36.9%over TiO2‐Cu,significantly more than the commercial P25TiO2.The enhancement of photocatalytic H2production activity can be attributed to improved rapid charge separation efficiency andexpanded light absorption window.This hydrothermal treatment with transition metal was proven to be a very facile and effective method for obtaining surface defects.展开更多
TiO2 thin films non-uniformly doped by La^3＋ were prepared by sol-gel method. The comparison of thin film activities, which was characterized by photocatalytic degradation of methyl orange, shows that doping modes ha...TiO2 thin films non-uniformly doped by La^3＋ were prepared by sol-gel method. The comparison of thin film activities, which was characterized by photocatalytic degradation of methyl orange, shows that doping modes have great activities. The non-uniformly effects on photocatalytic doped TiO2 films resuh in good photocatalytic activities with an optimal concentration; about 0. 5% （ atom fraction ）. UV-Vis transmittance spectra indicate that the absorption edges of these TiO2 thin films shift to ward longer wave- lengths remarkably, and electrochemical behavior also reveales that e^- -h^＋ pairs are prone to formation and separation under UV irradiation. The mechanism of photocatalytic activities are enhanced by La^3＋ non-uniformly doping was discussed on the analogy of the theory of “window effect” of solar cell heterojunction.展开更多
Engineering the electronic properties of semiconductor-based photocatalysts using elemental doping is an effective approach to improve their catalytic activity.Nevertheless,there still remain contradictions regarding ...Engineering the electronic properties of semiconductor-based photocatalysts using elemental doping is an effective approach to improve their catalytic activity.Nevertheless,there still remain contradictions regarding the role of the dopants played in photocatalysis.Herein,ultrathin ZnIn_(2)S_(4)(ZIS) nanosheets with oxygen doping were synthesized by a one-pot solvothermal method.XRD,XPS and Raman spectral measurements support the presence of lattice oxygen in the oxygen-doped ZIS(O-ZIS) sample.With optimum doping of oxygen,the ultrathin O-ZIS nanosheets show enhanced CO_(2)-to-CO conversion activity with a CO_(2)-evolving rate of 1680 μmol h^(-1) g^(-1) under visible light irradiation,which is about 7 times higher than that of the pristine ZIS.First-principle calculations support that doping of oxygen in the lattice of ZnIn_(2)S_(4) nanosheets plays a key role in tuning its electronic properties.The remarkable photocatalytic performance of O-ZIS can be assigned to a synergistic consequence of a unique ultrathin-layered structure and an upward shift of the conduction band minimum(CBM) caused by the oxygen doping into ZIS and the quantum confinement effect(QCE) induced by the decreased particle size after doping as well as to the improved charge separation efficiency.The present work offers a simple elemental doping method to promote charge separation at atomic level and illustrates the roles played by oxygen doping in photocatalysis,giving new insights into highly efficient artificial photosynthesis.展开更多
基金supported by the National Natural Science Foundation of China(Nos.51971070,10974037,and 62205011)the National Key Research and Development Program of China(No.2016YFA0200403)+6 种基金Eu-FP7 Project(No.247644)CAS Strategy Pilot Program(No.XDA 09020300)Fundamental Research Funds for the Central Universities(No.buctrc202122)the Open Research Project of Zhejiang province Key Laboratory of Quantum Technology and Device(No.20220401)the Open Research Project of Special Display and Imaging Technology Innovation Center of Anhui Province(No.2022AJ05001)funded by the Ph.D Foundation of Hebei University of Water Resources and Electric Engineering(No.SYBJ2202)Funded by Science and Technology Project of Hebei Education Department(No.BJK2022027)。
文摘Memristors as non-volatile memory devices have gained numerous attentions owing to their advantages in storage,in-memory computing, synaptic applications, etc. In recent years, two-dimensional(2D) materials with moderate defects have been discovered to exist memristive feature. However, it is very difficult to obtain moderate defect degree in 2D materials, and studied on modulation means and mechanism becomes urgent and essential. In this work, we realized memristive feature with a bipolar switching and a configurable on/off ratio in a two-terminal MoS_(2) device(on/off ratio ~100), for the first time, from absent to present using laser-modulation to few-layer defect-free MoS_(2)(about 10 layers), and its retention time in both high resistance state and low resistance state can reach 2×10^(4) s. The mechanism of the laser-induced memristive feature has been cleared by dynamic Monte Carlo simulations and first-principles calculations. Furthermore, we verified the universality of the laser-modulation by investigating other 2D materials of TMDs. Our work will open a route to modulate and optimize the performance of 2D semiconductor memristive devices.
基金the National Natural Science Foundation of China(12174015)the Natural Science Foundation of Beijing,China(2212003)+1 种基金the China National Petroleum Corporation Innovation Found(2021DQ02-1004)the National Natural Science Foundation of China(12102053)。
文摘Constructing robust surface and bulk structure is the prerequisite for realizing high performance high voltage LiCoO_(2)(LCO).Herein,we manage to synthesize a surface Mg-doping and bulk Al-doping coreshell structured LCO,which demonstrates excellent cycling performance.Half-cell shows 94.2%capacity retention after 100 cycles at 3.0-4.6 V(vs.Li/Li^(+))cycling,and no capacity decay after 300 cycles for fullcell test(3.0-4.55 V).Based on comprehensive microanalysis and theoretical calculations,the degradation mechanisms and doping effects are systematically revealed.For the undoped LCO,high voltage cycling induces severe interfacial and bulk degradations,where cracks,stripe defects,fatigue H2 phase,and spinel phase are identified in grain bulk.For the doped LCO,Mg-doped surface shell can suppress the interfacial degradations,which not only stabilizes the surface structure by forming a thin rock-salt layer but also significantly improves the electronic conductivity,thus enabling superior rate performance.Bulk Al-doping can suppress the lattice"breathing"effect and the detrimental H3 to H1-3 phase transition,which minimizes the internal strain and defects growth,maintaining the layered structure after prolonged cycling.Combining theoretical calculations,this work deepens our understanding of the doping effects of Mg and Al,which is valuable in guiding the future material design of high voltage LCO.
基金Project supported by the Fundamental Research Program of Shanxi Province,China (Grant No.20210302124228)the National Key Research and Development Program of China (Grant No.2022YFB4200203)+1 种基金the Key Project of Natural Science Foundation of Tianjin (Grant No.22JCZDJC00120)the 111 Project (Grant No.B16027)。
文摘It is highly desirable to enhance the long-term stability of perovskite solar cells(PSCs)so that this class of photovoltaic cells can be effectively used for the commercialization purposes.In this contribution,attempts have been made to use the two-step sequential method to dope EuBr_(2)into FAMAPbI_(3)perovskite to promote the stability.It is shown that the device durability at 85℃in air with RH of 20%-40%is improved substantially,and simultaneously the champion device efficiency of 23.04%is achieved.The enhancement in stability is attributed to two points:(ⅰ)EuBr_(2)doping effectively inhibits the decomposition andα-δphase transition of perovskite under ambient environment,and(ⅱ)EuBr_(2)aggregates in the oxidized format of Eu(BrO_(3))_(3)at perovskite grain boundaries and surface,hampering humidity erosion and mitigates degradation through coordination with H_(2)O.
基金supported by National Natural Science Foundation of China (22033009, 22121002, 22238011)。
文摘To improve the electrocatalytic transformation of carbon dioxide (CO_(2)) to multi-carbon (C_(2+)) products is of great importance.Here we developed a nitrogen-doped Cu catalyst,by which the maximum C_(2+) Faradaic efficiency can reach 72.7%in flow-cell system,with the partial current density reaching 0.62 A cm^(-2).The in situ Raman spectra demonstrate that the *CO adsorption can be strengthened on such a N-doped Cu catalyst,thus promoting the *CO utilization in the subsequent C–C coupling step.Simultaneously,the water activation can be well enhanced by N doping on Cu catalyst.Owing to the synergistic effects,the selectivity and activity for C_(2+) products over the N-deoped Cu catalyst are much improved.
基金financially supported by the Korea Institute of Energy Research(KIER)(grant no.C3-2401,2402,2403)the National Research Foundation(grant no.2022M3J1A1063019)funded by the Ministry of Science and ICT
文摘To demonstrate flexible and tandem device applications,a low-temperature Cu_(2)ZnSnSe_(4)(CZTSe)deposition process,combined with efficient alkali doping,was developed.First,high-quality CZTSe films were grown at 480℃by a single co-evaporation,which is applicable to polyimide(PI)substrate.Because of the alkali-free substrate,Na and K alkali doping were systematically studied and optimized to precisely control the alkali distribution in CZTSe.The bulk defect density was significantly reduced by suppression of deep acceptor states after the(NaF+KF)PDTs.Through the low-temperature deposition with(NaF+KF)PDTs,the CZTSe device on glass yields the best efficiency of 8.1%with an improved Voc deficit of 646 mV.The developed deposition technologies have been applied to PI.For the first time,we report the highest efficiency of 6.92%for flexible CZTSe solar cells on PI.Additionally,CZTSe devices were utilized as bottom cells to fabricate four-terminal CZTSe/perovskite tandem cells because of a low bandgap of CZTSe(~1.0 eV)so that the tandem cell yielded an efficiency of 20%.The obtained results show that CZTSe solar cells prepared by a low-temperature process with in-situ alkali doping can be utilized for flexible thin-film solar cells as well as tandem device applications.
基金supported by the National Natural Science Foundation of China(52272258)Beijing Nova Program(20220484214)+1 种基金Fundamental Research Funds for the Central Universities(No.2021JCCXJD01)Key R&D and transformation projects in Qinghai Province(2021-HZ-808)and Hebei Province(21314401D).
文摘The low energy density,unsatisfied cycling performance,potential safety issue and slow charging kinetics of the commercial lithium-ion batteries restrained their further application in the fields of fast charging and long-haul electric vehicles.Monoclinic TiNb_(2)O_(7)(TNO)with the theoretical capacity of 387 mAh g^(-1)has been proposed as a high-capacity anode materials to replace Li4Ti5O12.In this work,homovalent doping strategy was used to enhance the electrochemical performance of TiNb_(2)O_(7)(TNO)by employing Zr to partial substitute Ti through solvothermal method.The doping of Zr^(4+)ions can enlarge the lattice structure without changing the chemical valence of the original elements,refine and homogenize the grains,improve the electrical conductivity,and accelerate the ion diffusion kinetics,and finally enhance the cycle and rate performance.Specifically,Z0.05-TNO shows initial discharge capacity of as high as 312.2 mAh g^(-1)at 1 C and 244.8 mAh g^(-1)at 10 C,and still maintains a high specific capacity of 171.3 mAh g^(-1)after 800 cycles at 10 C.This study provides a new strategy for high-performance fast-charging energy storage electrodes.
基金This work received financial support from the National Natural Science Foundation of China(Grant Nos.U23A20574,52250010,and 52201242)the 261 Project MIIT,the Young Elite Scientists Sponsorship Program by CAST(Grant No.2021QNRC001)+1 种基金the Fundamental Research Funds for the Central Universities(Grant No.2242022R40018)the Jiangsu Funding Program for Excellent Postdoctoral Talent(Grant No.2022ZB75).
文摘Potassium-ion batteries(PIBs)offer a cost-effective and resource-abundant solution for large-scale energy storage.However,the progress of PIBs is impeded by the lack of high-capacity,long-life,and fast-kinetics anode electrode materials.Here,we propose a dual synergic optimization strategy to enhance the K^(+)storage stability and reaction kinetics of Bi_(2)S_(3) through two-dimensional compositing and cation doping.Externally,Bi_(2)S_(3) nanoparticles are loaded onto the surface of three-dimensional interconnected Ti_(3)C_(2)T_(x) nanosheets to stabilize the electrode structure.Internally,Cu^(2+)doping acts as active sites to accelerate K^(+)storage kinetics.Various theoretical simulations and ex situ techniques are used to elucidate the external–internal dual synergism.During discharge,Ti_(3)C_(2)T_(x) and Cu^(2+)collaboratively facilitate K+intercalation.Subsequently,Cu^(2+)doping primarily promotes the fracture of Bi2S3 bonds,facilitating a conversion reaction.Throughout cycling,the Ti_(3)C_(2)T_(x) composite structure and Cu^(2+)doping sustain functionality.The resulting Cu^(2+)-doped Bi2S3 anchored on Ti_(3)C_(2)T_(x)(C-BT)shows excellent rate capability(600 mAh g^(-1) at 0.1 A g^(–1);105 mAh g^(-1) at 5.0 A g^(-1))and cycling performance(91 mAh g^(-1) at 5.0 A g^(-1) after 1000 cycles)in half cells and a high energy density(179 Wh kg–1)in full cells.
基金Project (20771100) supported by the National Natural Science Foundation of China
文摘Li3V2-2/3xMnx（PO4）3（0≤x≤0.12） powders were synthesized by sol-gel method. The effect of Mn2＋-doping on the structure and electrochemical performances of Li3V2（PO4）3/C was characterized by XRD, SEM, XPS, galvanostatic charge /discharge and electrochemical impedance spectroscopy（EIS）. The XRD study shows that a small amount of Mn2＋-doped does not alter the structure of Li3V2（PO4）3/C materials, and all Mn2＋-doped samples are of pure single phase with a monoclinic structure （space group P21/n）. The XPS analysis indicates that valences state of V and Mn are ＋3 and ＋2 in Li3V1.94Mn0.09（PO4）3/C, respectively, and the citric acid in raw materials was decomposed into carbon during calcination, and residual carbon exists in Li3V1.94Mn0.09（PO4）/C. The results of electrochemical measurements show that Mn2＋-doping can improve the cyclic stability and rate performance of these cathode materials. The Li3V1.94Mn0.09（PO4）3/C cathode material shows the best cyclic stability and rate performance. For example, at the discharge current density of 40 mA/g, after 100 cycles, the discharge capacity of Li3V1.94Mn0.09（PO4）3/C declines from initial 158.8 mA·h/g to 120.5 mA·h/g with a capacity retention of 75.9%; however, that of the Mn-undoed sample declines from 164.2 mA·h/g to 72.6 mA·h/g with a capacity retention of 44.2%. When the discharge current is increased up to 1C, the intial discharge capacity of Li3V1.94Mn0.09（PO4）3/C still reaches 146.4 mA·h/g, and the discharge capacity maintains at 107.5 mA·h/g after 100 cycles. The EIS measurement indicates that Mn2＋-doping with a appropriate amount of Mn2＋ decreases the charge transfer resistance, which is favorable for the insertion/extraction of Li＋.
基金V. ACKNOWLEDGMENTS This work was supported by the National Natural Science Foundation of China （No.51072191）, One Hundred Talents Program of the Chinese Academy of Sciences, the National Basic Research Program of China （No.2012CB922004）, the National Natural Science Foundation of China （No.11105133）, and USTC- NSRL Association Funding （No.KY2060140005）.
文摘Using density functional theory, we studied band structure, density of states, optical proper- ties and Mulliken population of the pure and SiN doped BaMgAl10017：Eu^2＋ （BAM：Eu^2＋） phosphors. Calculation results showed that the bands of BAM：Eu2＋ were of low band energy dispersion, indicating large joint density of states, hence high performance of optical absorption and luminescence. BAM：Eu^2＋ showed stronger absorption intensity while Eu^2＋ occupied the BR sites instead of the mO sites. The concentration of Eu^2＋ at BR sites increased while that at mO sites decreased after Si-N doping. The influence of the variation of Eu^2＋ distribution on the spectra was stronger than the influence of the decrease of Eu^2＋ PDOS when SiN concentration was lower than 0.25, therefore the absorption and luminescence intensity of BAM：Eu^2＋ were enhanced. Mulliken population of Si-N bond was higher than A1-O bond, while that of Eu-N bond was higher than Eu-O bond as well, indicating that Si-N bonds and Eu-N bonds possessed higher covalence than Al-O bonds and Eu-N bonds respectively. The existence of Si-N bonds and Eu-N bonds enhanced the local covalence of Eu^2＋, hence the optical stability of BAM：Eu^2＋.
基金Project supported by the National "973"Project (2004CB719503)Project supported by the National Natural ScienceFoundation of China (50502023)
文摘CeO2-ZrO2-MnOx mixed oxide series were prepared by sol-gel method. CO pulse and CO-O2 cycle measurements were carried out to examine the oxygen storage complete capacity （OSCC） and dynamic oxygen storage capacity （OSC） of the samples. The doping method brought about strong interactions between manganese oxide and ceria, both in the bulk and on the surface. Only a small part of Mn cations are incorporated into the ceria lattice to form solid solutions and the remaining are left on the surface as finely dispersed Mn3O4. The OSC behaviors of the materials are influenced by the doping amount of Mn and the solubility of Mn in the CeO2 lattice. The OSC is more easily affected by available contents of oxygen storage components when the measurement frequency is low. Comparatively, the concentration of lattice defects, which affects the mobility of bulk oxygen, is the determining factor under high frequency.
文摘Ultrathin TiO_(2)nanosheets with coexposed{001}/{101}facets have attracted considerable attention because of their high photocatalytic activity.However,the charge-separated states in the TiO_(2)nanosheets must be extended to further enhance their photocatalytic activity for H_(2)evolution.Herein,we present a successful attempt to selectively dope lanthanide ions into the{101}facets of ultrathin TiO_(2)nanosheets with coexposed{001}/{101}facets through a facile one-step solvothermal method.The lanthanide doping slightly extended the light-harvesting region and markedly improved the charge-separated states of the TiO_(2)nanosheets as evidenced by UV-vis absorption and steady-state/transient photoluminescence spectra.Upon simulated sunlight irradiation,we observed a 4.2-fold enhancement in the photocatalytic H_(2)evolution activity of optimal Yb^(3+)-doped TiO_(2)nanosheets compared to that of their undoped counterparts.Furthermore,when Pt nanoparticles were used as cocatalysts to reduce the H_(2)overpotential in this system,the photocatalytic activity enhancement factor increased to 8.5.By combining these results with those of control experiments,we confirmed that the extended charge-separated states play the main role in the enhancement of the photocatalytic H_(2)evolution activity of lanthanide-doped TiO_(2)nanosheets with coexposed{001}/{101}facets.
基金supported by the National Natural Science Foundation of China(21876168,21507130)the Key Projects for Common Key Technology Innovation in Key Industries in Chongqing(cstc2016zdcy-ztzx0020-01)+2 种基金the Chongqing Science&Technology Commission(cstc2016jcyjA0070,cstckjcxljrc13)the Open Project Program of Chongqing Key Laboratory of Catalysis and Functional Organic Molecules from Chongqing Technology and Business University(1456029)the Graduate Innovation Project of Chongqing Technology and Business University(yjscxx201803-028-22)~~
文摘A series of V2O5‐WO3/TiO2‐ZrO2,V2O5‐WO3/TiO2‐CeO2,and V2O5‐WO3/TiO2‐CeO2‐ZrO2 catalysts were synthesized to improve the selective catalytic reduction(SCR)performance and the K‐poisoning resistance of a V2O5‐WO3/TiO2 catalyst.The physicochemical properties were investigated by using XRD,BET,NH3‐TPD,H2‐TPR,and XPS,and the catalytic performance and K‐poisoning resistance were evaluated via a NH3‐SCR model reaction.Ce^4+and Zr^4+co‐doping were found to enhance the conversion of NOx,and exhibit the best K‐poisoning resistance owing to the largest BET‐specific surface area,pore volume,and total acid site concentration,as well as the minimal effects on the surface acidity and redox ability from K poisoning.The V2O5‐WO3/TiO2‐CeO2‐ZrO2 catalyst also presents outstanding H2O+SO2 tolerance.Finally,the in situ DRIFTS reveals that the NH3‐SCR reaction over the V2O5‐WO3/TiO2‐CeO2‐ZrO2 catalyst follows an L‐H mechanism,and that K poisoning does not change the reaction mechanism.
基金supported by the Double First‐rate Subject‐Food Science and Engineering Program of Hebei Province (2018SPGCA18)Young Tip‐top Talents Plan of Universities and Colleges in Hebei Province of China (BJ2017026)the Specific Foundation for Doctor in Hebei Agriculture University of China (ZD201709)~~
文摘Inefficient charge separation and limited light absorption are two critical issues associated with high‐efficiency photocatalytic H2production using TiO2.Surface defects within a certain concentration range in photocatalyst materials are beneficial for photocatalytic activity.In this study,surface defects(oxygen vacancies and metal cation replacement defects)were induced with a facile and effective approach by surface doping with low‐cost transition metals(Co,Ni,Cu,and Mn)on ultrafine TiO2.The obtained surface‐defective TiO2exhibited a3–4‐fold improved activity compared to that of the original ultrafine TiO2.In addition,a H2production rate of3.4μmol/h was obtained using visible light(λ>420nm)irradiation.The apparent quantum yield(AQY)at365nm reached36.9%over TiO2‐Cu,significantly more than the commercial P25TiO2.The enhancement of photocatalytic H2production activity can be attributed to improved rapid charge separation efficiency andexpanded light absorption window.This hydrothermal treatment with transition metal was proven to be a very facile and effective method for obtaining surface defects.
文摘TiO2 thin films non-uniformly doped by La^3＋ were prepared by sol-gel method. The comparison of thin film activities, which was characterized by photocatalytic degradation of methyl orange, shows that doping modes have great activities. The non-uniformly effects on photocatalytic doped TiO2 films resuh in good photocatalytic activities with an optimal concentration; about 0. 5% （ atom fraction ）. UV-Vis transmittance spectra indicate that the absorption edges of these TiO2 thin films shift to ward longer wave- lengths remarkably, and electrochemical behavior also reveales that e^- -h^＋ pairs are prone to formation and separation under UV irradiation. The mechanism of photocatalytic activities are enhanced by La^3＋ non-uniformly doping was discussed on the analogy of the theory of “window effect” of solar cell heterojunction.
基金financially supported by the National Natural Science Foundation of China(Grants Nos.21976116 and 21902095)Shaanxi Science and Technology Program(2020KWZ005)+3 种基金SAFEA of China(High-end foreign expert project # G20190241013)Natural Foundation of Shaanxi Province(No.2020JQ-711)Group Linkage Program of Alexander-vonHumboldt Foundation of Germanythe scientific research startup fund of Shannxi University of Science and Technology。
文摘Engineering the electronic properties of semiconductor-based photocatalysts using elemental doping is an effective approach to improve their catalytic activity.Nevertheless,there still remain contradictions regarding the role of the dopants played in photocatalysis.Herein,ultrathin ZnIn_(2)S_(4)(ZIS) nanosheets with oxygen doping were synthesized by a one-pot solvothermal method.XRD,XPS and Raman spectral measurements support the presence of lattice oxygen in the oxygen-doped ZIS(O-ZIS) sample.With optimum doping of oxygen,the ultrathin O-ZIS nanosheets show enhanced CO_(2)-to-CO conversion activity with a CO_(2)-evolving rate of 1680 μmol h^(-1) g^(-1) under visible light irradiation,which is about 7 times higher than that of the pristine ZIS.First-principle calculations support that doping of oxygen in the lattice of ZnIn_(2)S_(4) nanosheets plays a key role in tuning its electronic properties.The remarkable photocatalytic performance of O-ZIS can be assigned to a synergistic consequence of a unique ultrathin-layered structure and an upward shift of the conduction band minimum(CBM) caused by the oxygen doping into ZIS and the quantum confinement effect(QCE) induced by the decreased particle size after doping as well as to the improved charge separation efficiency.The present work offers a simple elemental doping method to promote charge separation at atomic level and illustrates the roles played by oxygen doping in photocatalysis,giving new insights into highly efficient artificial photosynthesis.
