The Makran accretionary wedge has the smallest subduction angle among any accretionary prism in the world. The factors controlling the spacing and morphological development of its deep thrust faults, as well as the fo...The Makran accretionary wedge has the smallest subduction angle among any accretionary prism in the world. The factors controlling the spacing and morphological development of its deep thrust faults, as well as the formation mechanism of shallow normal faults, remain unclear. Meanwhile, the factors affecting the continuity of plane faults must be comprehensively discussed. Clarifying the development characteristics and deformation mechanisms of the Makran accretionary wedge is crucial to effectively guide the exploration of gas hydrate deposits in the area. This study aims to interpret seismic data to identify typical structures in the Makran accretionary wedge, including deep imbricate thrust faults, shallow and small normal faults, wedge-shaped piggyback basins, mud diapirs with fuzzy and disorderly characteristics of reflection, décollements with a northward tilt of 1° – 2°, and large seamounts. Physical simulation-based experiments are performed to comprehensively analyze the results of the plane, section, and slices of the wedge. Results reveal that the distances between and shapes of thrust faults in the deep parts of the Makran accretionary wedge are controlled by the bottom décollement. The uplift of the thrust fault-related folds and the upwelling of the mud diapirs primarily contribute to the formation of small normal faults in the shallow part of the area. The mud diapirs originate from plastic material at the bottom, while those that have developed in the area near the trench are larger. Seamounts and mud diapirs break the continuity of fault plane distribution.展开更多
It has been demonstrated that heat absorption method by using the inorganic material rod to cool the molten steel can significantly reduce the macrosegregation level of the large steel ingot.However,owing to the opaci...It has been demonstrated that heat absorption method by using the inorganic material rod to cool the molten steel can significantly reduce the macrosegregation level of the large steel ingot.However,owing to the opacity of the molten steel,the physical mechanism of the heat absorption method is not clear.In this work,a transparent hydraulic physical model with water and paraffin wax was built to simulate the melting and floating processes of inorganic materials in the molten steel.A mathematical simulation was also carried out to analyze the connection between the actual ingot and the physical model.Results show that it is feasible to simulate the molten steel and inorganic materials with water and paraffin wax.With the help of the physical model,the process of the melting of paraffin wax and its floating to the surface of water were clearly observed,during which the temperature of water at some characteristic positions in the mold was recorded.The visualization findings demonstrate that the melting and floating processes of paraffin wax can help to bring the heat from the center of the mold to the top surface more quickly,which reduces the superheat and significantly accelerates the cooling rate of water.The experimental results show that for the water with a certain superheat,the use of a larger mass of paraffin wax can accelerate the cooling of the water,but there is a risk of incomplete melting of the paraffin wax.A higher superheat of water will lead to a quicker melting rate for a given mass of paraffin wax,while a lower superheat leads to the incomplete melting of paraffin wax as well.展开更多
In order to understand the mechanism of air flooding shale oil, an online physical simulation method for enhanced shale oil recovery by air injection was established by integrating CT scanning and nuclear magnetic res...In order to understand the mechanism of air flooding shale oil, an online physical simulation method for enhanced shale oil recovery by air injection was established by integrating CT scanning and nuclear magnetic resonance(NMR). The development effect of shale oil by air flooding under different depletion pressures, the micro-production characteristics of pore throats with different sizes and the mechanism of shale oil recovery by air flooding were analyzed. The effects of air oxygen content, permeability, gas injection pressure, and fractures on the air flooding effect in shale and crude oil production in pores with different sizes were analyzed. The recovery of shale oil can be greatly improved by injecting air into the depleted shale reservoir, but the oil displacement efficiency and the production degree of different levels of pore throats vary with the injection timing. The higher the air oxygen content and the stronger the low-temperature oxidation, the higher the production degree of pores with different sizes and the higher the shale oil recovery. The higher the permeability and the better the pore throat connectivity, the stronger the fluid flow capacity and the higher the shale oil recovery. As the injection pressure increases, the lower limit of the production degree of pore throats decreases, but gas channeling may occur to cause a premature breakthrough;as a result, the recovery increases and then decreases. Fractures can effectively increase the contact area between gas and crude oil, and increase the air sweep coefficient and matrix oil drainage area by supplying oil to fractures through the matrix, which means that a proper fracturing before air injection can help to improve the oil displacement effect under a reasonable production pressure difference.展开更多
To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale co...To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.展开更多
A micro-nano pore three-dimensional visualized real-time physical simulation of natural gas charging, in-situ pore-scale computation, pore network modelling, and apparent permeability evaluation theory were used to in...A micro-nano pore three-dimensional visualized real-time physical simulation of natural gas charging, in-situ pore-scale computation, pore network modelling, and apparent permeability evaluation theory were used to investigate laws of gas and water flow and their distribution, and controlling factors during the gas charging process in low-permeability(tight) sandstone reservoir. By describing features of gas-water flow and distribution and their variations in the micro-nano pore system, it is found that the gas charging in the low permeability(tight) sandstone can be divided into two stages, expansion stage and stable stage. In the expansion stage, the gas flows continuously first into large-sized pores then small-sized pores, and first into centers of the pores then edges of pores;pore-throats greater than 20 μm in radius make up the major pathway for gas charging. With the increase of charging pressure, movable water in the edges of large-sized pores and in the centers of small pores is displaced out successively. Pore-throats of 20-50 μm in radius and pore-throats less than 20 μm in radius dominate the expansion of gas charging channels at different stages of charging in turn, leading to reductions in pore-throat radius, throat length and coordination number of the pathway, which is the main increase stage of gas permeability and gas saturation. Among which, pore-throats 30-50 μm in radius control the increase pattern of gas saturation. In the stable stage, gas charging pathways have expanded to the maximum, so the pathways keep stable in pore-throat radius, throat length, and coordination number, and irreducible water remains in the pore system, the gas phase is in concentrated clusters, while the water phase is in the form of dispersed thin film, and the gas saturation and gas permeability tend stable. Connected pore-throats less than 20 μm in radius control the expansion limit of the charging pathways, the formation of stable gas-water distribution, and the maximum gas saturation. The heterogeneity of connected pore-throats affects the dynamic variations of gas phase charging and gas-water distribution. It can be concluded that the pore-throat configuration and heterogeneity of the micro-nanometer pore system control the dynamic variations of the low-permeability(tight) sandstone gas charging process and gas-water distribution features.展开更多
Due to the tremendous amount of high-resolution measurement information,array laterolog is widely used in evaluations of deviated anisotropic reservoirs.However,the precision of a complementary numerical simulation sh...Due to the tremendous amount of high-resolution measurement information,array laterolog is widely used in evaluations of deviated anisotropic reservoirs.However,the precision of a complementary numerical simulation should be improved as high as the core of fine-scale reservoir evaluation.Therefore,the 3D finite element method(3D-FEM)is presented to simulate the array laterolog responses.Notably,a downscaled physical simulation system is introduced to validate and calibrate the precision of the 3D-FEM.First,the size of the downscaled system is determined by COMSOL.Then,the surrounding and investigated beds are represented by a sodium chloride solution and planks soaked in solution,respectively.Finally,a half-space measurement scheme is presented to improve the experimental efficiency.Moreover,the corresponding sensitivity function and separation factor are established to analyze the effects of the formation anisotro py and dipping angle on the array laterolog responses.The numerical and experimental results indicate that the half-space method is practical,and the mean relative error between the numerical and experimental results is less than 5%,which indicates that the numerical simulation is accurate.With the proposed approach,the reversal angle of array laterolog response curves in anisotropic formations can be observed,and this range is determined to be 50°-62°.展开更多
The shear behavior of backfill-rock composites is crucial for mine safety and the management of surface subsidence.For exposing the shear failure mechanism of backfill-rock composites,we conducted shear tests on backf...The shear behavior of backfill-rock composites is crucial for mine safety and the management of surface subsidence.For exposing the shear failure mechanism of backfill-rock composites,we conducted shear tests on backfill-rock composites under three constant normal loads,compared with the unfilled rock.To investigate the macro-and meso-failure characteristics of the samples in the shear tests,the cracking behavior of samples was recorded by a high-speed camera and acoustic emission monitoring.In parallel with the experimental test,the numerical models of backfill-rock composites and unfilled rock were established using the discrete element method to analyze the continuous-discontinuous shearing process.Based on the damage mechanics and statistics,a novel shear constitutive model was proposed to describe mechanical behavior.The results show that backfill-rock composites had a special bimodal phenomenon of shearing load-deformation curve,i.e.the first shearing peak corresponded to rock break and the second shearing peak induced by the broken of aeolian sand-cement/fly ash paste backfill.Moreover,the shearing characteristic curves of the backfill-rock composites could be roughly divided into four stages,i.e.the shear failure of the specimens experienced:stage I:stress concentration;stage II:crack propagation;stage III:crack coalescence;stage IV:shearing friction.The numerical simulation shows that the existence of aeolian sand-cement/fly ash paste backfill inevitably altered the coalescence type and failure mode of the specimens and had a strengthening effect on the shear strength of backfillrock composites.Based on damage mechanics and statistics,a shear constitutive model was proposed to describe the shear fracture characteristics of specimens,especially the bimodal phenomenon.Finally,the micro-and meso-mechanisms of shear failure were discussed by combining the micro-test and numerical results.The research can advance the better understanding of the shear behavior of backfill-rock composites and contribute to the safety of mining engineering.展开更多
In order to increase the contact area and promote the mass transfer process of gas and liquid,the process of the bubble refine-ment in a metallurgical reactor with mechanical agitation was studied by physical simulati...In order to increase the contact area and promote the mass transfer process of gas and liquid,the process of the bubble refine-ment in a metallurgical reactor with mechanical agitation was studied by physical simulation.Based on the capillary number,a prediction equation for the bubble refinement was established.The effects of the gas flow rate,the stirring speed and thestirring depth on the bubble refinement in the reactor were discussed in detail.The distribution of the bubble diameter in thereactor was obtained under different conditions.The results show that when the stirring speed reaches 300 r/min,the bubblediamcter mainly distributes in the range of 1-2 mm.A higher gas flow rate may increase the number of bubbles in the meltand promote the bubble refinement process.The mechanism of bubble refinement under mechanical agitation was analyzed.and the results indicated that the stirring speed.,the blade area and the blade inclination are the main influencing factors.展开更多
The ultra-low porosity and permeability,as well as complex occurrence and transport state of shale reservoir make it possess special L-type production characteristic curve and complicated shale gas flow mechanism.To s...The ultra-low porosity and permeability,as well as complex occurrence and transport state of shale reservoir make it possess special L-type production characteristic curve and complicated shale gas flow mechanism.To solve the difficulty of collecting complete production data due to short production time and operation discontinuity,a full-diameter core physical simulation experiment on the full lifecycle production process of shale gas well depletion is conducted with the purpose of obtaining many important production data including complete pressure and daily gas output in the simulated production process of shale gas well.The experimental results show the production characteristic from simulation is consistent with those from gas well.Based on the simulation data,the critical desorption pressure(12 MPa)of core,free gas production(3820.8 mL),adsorbed gas production(2151.2 mL),the proportion of the daily gas production between free and absorbed gas under different time and formation pressure,as well as the production time and final recovery rate corresponding to abandoned pressure,can be determined accurately.Numerical inversion is carried out to calculate the production performance curve of shale gas well and predict the development effect of gas well based on well testing and similarity analysis of the dimensionless time between core experiment and gas well production.Finally,the permeability and the fracturing effect(fracture network density)as the keys to the effective development of shale gas reservoirs are proposed.The permeability is the fundamental factor and the fracturing technology is the major means.展开更多
Considering the action mechanisms of overpressure on physical changes in skeleton particles of deep reservoir rocks and the differences in physical changes of skeleton particles under overpressure and hydrostatic pres...Considering the action mechanisms of overpressure on physical changes in skeleton particles of deep reservoir rocks and the differences in physical changes of skeleton particles under overpressure and hydrostatic pressure, the sandstone of the Jurassic Toutunhe Formation in the southern margin of Junggar Basin was taken as an example for physical modeling experiment to analyze the action mechanisms of overpressure on the physical properties of deep reservoirs. (1) In the simulated ultra-deep layer with a burial depth of 6000-8000 m, the mechanical compaction under overpressure reduces the remaining primary pores by about a half that under hydrostatic pressure. Overpressure can effectively suppress the mechanical compaction to allow the preservation of intergranular primary pores. (2) The linear contact length ratio under overpressure is always smaller than the linear contact length ratio under hydrostatic pressure at the same depth. In deep reservoirs, the difference between the mechanical compaction degree under overpressure and hydrostatic pressure shows a decreasing trend, the effect of abnormally high pressure to resist the increase of effective stress is weakened, and the degree of mechanical compaction is gradually close to that under hydrostatic pressure. (3) The microfractures in skeleton particles of deep reservoirs under overpressure are thin and long, while the microfractures in skeleton particles of deep reservoirs under hydrostatic pressure are short and wide. This difference is attributed to the probable presence of tension fractures in the rocks containing abnormally high pressure fluid. (4) The microfractures in skeleton particles under overpressure were mainly formed later than that under hydrostatic pressure, and the development degree and length of microfractures both extend deeper. (5) The development stages of microfractures under overpressure are mainly controlled by the development stages of abnormally high pressure and the magnitude of effective stress acting on the skeleton particles. Moreover, the development stages of microfractures in skeleton particles are more than those under hydrostatic pressure in deep reservoir. The multi-stage abnormally high pressure plays an important role in improving the physical properties of deep reservoirs.展开更多
A model of binding forces in metals and alloys, based on the density functional theory and accounted effects of the many-body interactions, was proposed. The developed method can be easily applied for study of metals ...A model of binding forces in metals and alloys, based on the density functional theory and accounted effects of the many-body interactions, was proposed. The developed method can be easily applied for study of metals and alloys by the molecular dynamics simulation. The potentials of interatomic interactions have been found by the proposed method and applied for calculations of equation of state, elastic moduli and phonon dispersion in metals Ni, Al, alloys NiAl and Ni3Al. Results of the calculations are in good agreement with known experimental data both for pure metals and alloys.展开更多
The dual transmitter implements the equivalent anti-magnetic flux transient electromagnetic method, which can effectively reduce the scope of the transient electromagnetic detection blind area. However, this method is...The dual transmitter implements the equivalent anti-magnetic flux transient electromagnetic method, which can effectively reduce the scope of the transient electromagnetic detection blind area. However, this method is rarely reported in the detection of pipelines in urban geophysical exploration and the application of coal mines. Based on this, this paper realizes the equivalent anti-magnetic flux transient electromagnetic method based on the dual launcher. The suppression effect of this method on the blind area is analyzed by physical simulation. And the detection experiment of underground pipelines is carried out outdoors. The results show that the dual launcher can significantly reduce the turn-off time, thereby effectively reducing the impact of the blind area on the detection results, and the pipeline detection results verify the device’s effectiveness. Finally, based on the ground experimental results, the application prospect of mine advanced detection is discussed. Compared with other detection fields, the formation of blind areas is mainly caused by the equipment. If the dual launcher can be used to reduce the blind area, the accuracy of advanced detection can be improved more effectively. The above research results are of great significance for improving the detection accuracy of the underground transient electromagnetic method.展开更多
In fog, visibility is reduced. This reduction in visibility is measured by the meteorological optical range (MOR), which is important for studying human perception and various sensors in foggy conditions. The Cerema P...In fog, visibility is reduced. This reduction in visibility is measured by the meteorological optical range (MOR), which is important for studying human perception and various sensors in foggy conditions. The Cerema PAVIN Fog & Rain platform is capable of producing calibrated fog in order to better analyses it and understand its consequences. The problem is that the droplets produced by the platform are not large enough to resemble real fog. This can have a major impact on measurements since the interaction between electromagnetic waves and fog depends on the wavelength and diameter of the droplets. To remedy this, Cerema is building a new platform with new equipment capable of generating fog. This study analyses different nozzles and associated usage parameters such as the type of water used and the pressure used. The aim is to select the best nozzle with the associated parameters for producing large-diameter droplets and therefore more realistic fog.展开更多
Stress sensitivity is a very important index to understand the seepage characteristics of a reservoir.In this study,dedicated experiments and theoretical arguments based on the visualization of porous media are used t...Stress sensitivity is a very important index to understand the seepage characteristics of a reservoir.In this study,dedicated experiments and theoretical arguments based on the visualization of porous media are used to assess the effects of the fracture angle,spacing,and relevant elastic parameters on the principal value of the permeability tensor.The fracture apertures at different angles show different change rates,which influence the relative permeability for different sets of fractures.Furthermore,under the same pressure condition,the fractures with different angles show different degrees of deformation so that the principal value direction of permeability rotates.This phenomenon leads to a variation in the water seepage direction in typical water-injection applications,thereby hindering the expected exploitation effect of the original well network.Overall,the research findings in this paper can be used as guidance to improve the effectiveness of water injection exploitation in the oil field industry.展开更多
Deep simulations have gained widespread attention owing to their excellent acceleration performances.However,these methods cannot provide effective collision detection and response strategies.We propose a deep interac...Deep simulations have gained widespread attention owing to their excellent acceleration performances.However,these methods cannot provide effective collision detection and response strategies.We propose a deep interac-tive physical simulation framework that can effectively address tool-object collisions.The framework can predict the dynamic information by considering the collision state.In particular,the graph neural network is chosen as the base model,and a collision-aware recursive regression module is introduced to update the network parameters recursively using interpenetration distances calculated from the vertex-face and edge-edge tests.Additionally,a novel self-supervised collision term is introduced to provide a more compact collision response.This study extensively evaluates the proposed method and shows that it effectively reduces interpenetration artifacts while ensuring high simulation efficiency.展开更多
Based on the typical dissection of various onshore tight oil fields in China,the tight oil migration and accumulation mechanism and enrichment-controlling factors in continental lake basins are analyzed through nuclea...Based on the typical dissection of various onshore tight oil fields in China,the tight oil migration and accumulation mechanism and enrichment-controlling factors in continental lake basins are analyzed through nuclear magnetic resonance(NMR)displacement physical simulation and Lattice Boltzmann numerical simulation by using the samples of source rock,reservoir rock and crude oil.In continental lake basins,the dynamic forces driving hydrocarbon generation and expulsion of high-quality source rocks are the foundational power that determines the charging efficiency and accumulation effect of tight oil,the oil migration resistance is a key element that influences the charging efficiency and accumulation effect of tight oil,and the coupling of charging force with pore-throat resistance in tight reservoir controls the tight oil accumulation and sweet spot enrichment.The degree of tight oil enrichment in continental lake basins is controlled by four factors:source rock,reservoir pore-throat size,anisotropy of reservoir structure,and fractures.The high-quality source rocks control the near-source distribution of tight oil,reservoir physical properties and pore-throat size are positively correlated with the degree of tight oil enrichment,the anisotropy of reservoir structure reveals that the parallel migration rate is the highest,and intralayer fractures can improve the migration and accumulation efficiency and the oil saturation.展开更多
Constrained by the geological burial history of Cretaceous Qingshuihe Formation in the southern margin of Junggar Basin, the diagenetic physical simulation experiment was carried out with the low-mature sandstone samp...Constrained by the geological burial history of Cretaceous Qingshuihe Formation in the southern margin of Junggar Basin, the diagenetic physical simulation experiment was carried out with the low-mature sandstone samples taken from the outcrop area. Then, coupling with the regional geological data, the reformation of reservoirs with different diagenetic intensities by microfractures and the significance of microfractures for development of high-quality reservoirs were discussed. The results show that the large-scale microfractures were formed in the stage of late rapid deep burial, roughly equivalent to the period when organic acids were filled. The microfractures created good conditions for migration of oil and gas in deep and ultra-deep clastic rocks, and also enabled the transport of organic acids to the reservoirs for ensuing the late continuous dissolution of cements and particles. The existence of matrix pores and microfractures in the reservoirs before the rapid deep burial determined how the microfractures formed during rapid deep burial improved the reservoir quality. If matrix pores and microfractures were more developed and the cementation degree was lower before the rapid deep burial, the microfractures would be more developed and the dissolution degree would be higher during the late rapid deep burial, and so the reservoir quality would be improved more greatly, which can increase the reservoir permeability by up to 55%. If cementation was very strong, but matrix pores were not developed and microfractures existed locally before the rapid deep burial, the microfractures would also be more developed during the late rapid deep burial, which can increase the reservoir permeability by 43%. If cementation was strong, matrix pores were absent, and microfractures were not developed, limited microfractures would be formed during the late rapid deep burial, which can increase the reservoir permeability by only 16%. Formation of large-scale microfractures during late rapid deep burial and promotion of such microfractures to the dissolution of organic acids are considered as key diagenetic factors for the development of deep and ultra-deep high-quality reservoirs.展开更多
Given its relevance to the exploitation of ultra-low permeability reservoirs,which account for a substantial proportion of the world’s exploited and still unexploited reserves,in the present study the development of ...Given its relevance to the exploitation of ultra-low permeability reservoirs,which account for a substantial proportion of the world’s exploited and still unexploited reserves,in the present study the development of an adequate water injection system is considered.Due to the poor properties and weak seepage capacity of these reservoirs,the water injection pressure typically increases continuously during water flooding.In this research,the impact on such a process of factors as permeability,row spacing,and pressure gradient is evaluated experimentally using a high-pressure large-scale outcrop model.On this basis,a comprehensive evaluation coefficient is introduced able to account for the effective driving pressure.展开更多
Combined with NMR,core experiment,slim-tube tests,nano-CT and oil composition analysis,the mechanism of CO(2) enhanced oil recovery had been studied.CO_(2) flooding under supercritical state could achieve higher oil r...Combined with NMR,core experiment,slim-tube tests,nano-CT and oil composition analysis,the mechanism of CO(2) enhanced oil recovery had been studied.CO_(2) flooding under supercritical state could achieve higher oil recovery.In the process of crude oil displaced by supercritical CO2,the average oil recovery was 46.98% at low displacement pressures and 73.35% at high displacement pressures.The permeability of cores after CO2 flooding was only 28%-64% of those before flooding.As to the expelled oil,the contents of asphaltenes and non-hydrocarbons decreased,and saturated hydrocarbons of above C25 were absent in some samples,indicating that they had been retained in cores as demonstrated by CT and NMR experiments.In slim-tube tests,the heavy components of oil were expelled when the pressure increased to 30 MPa.There was a reasonable bottom hole pressure(BHP) below which the heavy components driven out from the far-well zone would deposit in the near-well zone,and when the pressure was too high,the nonhydrocarbon detention may cause block.The smaller throat and worse physical properties the porous media had,the higher displacement pressure would be required to achieve a good oil displacement efficiency.The increase in displacement pressure or time of interaction between oil and CO2 could effectively enhance oil recovery.展开更多
基金funded by the National Natural Science Foundation of China(No.42076069).
文摘The Makran accretionary wedge has the smallest subduction angle among any accretionary prism in the world. The factors controlling the spacing and morphological development of its deep thrust faults, as well as the formation mechanism of shallow normal faults, remain unclear. Meanwhile, the factors affecting the continuity of plane faults must be comprehensively discussed. Clarifying the development characteristics and deformation mechanisms of the Makran accretionary wedge is crucial to effectively guide the exploration of gas hydrate deposits in the area. This study aims to interpret seismic data to identify typical structures in the Makran accretionary wedge, including deep imbricate thrust faults, shallow and small normal faults, wedge-shaped piggyback basins, mud diapirs with fuzzy and disorderly characteristics of reflection, décollements with a northward tilt of 1° – 2°, and large seamounts. Physical simulation-based experiments are performed to comprehensively analyze the results of the plane, section, and slices of the wedge. Results reveal that the distances between and shapes of thrust faults in the deep parts of the Makran accretionary wedge are controlled by the bottom décollement. The uplift of the thrust fault-related folds and the upwelling of the mud diapirs primarily contribute to the formation of small normal faults in the shallow part of the area. The mud diapirs originate from plastic material at the bottom, while those that have developed in the area near the trench are larger. Seamounts and mud diapirs break the continuity of fault plane distribution.
基金supported by Shanghai Post-doctoral Excellence Program of China(No.2021166)Shanghai Rising-Star Program(Nos.20QA1403800 and 21QC1401500)Shanghai Science and Technology Committee(No.21511103600).
文摘It has been demonstrated that heat absorption method by using the inorganic material rod to cool the molten steel can significantly reduce the macrosegregation level of the large steel ingot.However,owing to the opacity of the molten steel,the physical mechanism of the heat absorption method is not clear.In this work,a transparent hydraulic physical model with water and paraffin wax was built to simulate the melting and floating processes of inorganic materials in the molten steel.A mathematical simulation was also carried out to analyze the connection between the actual ingot and the physical model.Results show that it is feasible to simulate the molten steel and inorganic materials with water and paraffin wax.With the help of the physical model,the process of the melting of paraffin wax and its floating to the surface of water were clearly observed,during which the temperature of water at some characteristic positions in the mold was recorded.The visualization findings demonstrate that the melting and floating processes of paraffin wax can help to bring the heat from the center of the mold to the top surface more quickly,which reduces the superheat and significantly accelerates the cooling rate of water.The experimental results show that for the water with a certain superheat,the use of a larger mass of paraffin wax can accelerate the cooling of the water,but there is a risk of incomplete melting of the paraffin wax.A higher superheat of water will lead to a quicker melting rate for a given mass of paraffin wax,while a lower superheat leads to the incomplete melting of paraffin wax as well.
基金Supported by the PetroChina Major Scientific and Technological Research Project (2021DJ1102)PetroChina Science and Technology Major Project (2022kt1001)。
文摘In order to understand the mechanism of air flooding shale oil, an online physical simulation method for enhanced shale oil recovery by air injection was established by integrating CT scanning and nuclear magnetic resonance(NMR). The development effect of shale oil by air flooding under different depletion pressures, the micro-production characteristics of pore throats with different sizes and the mechanism of shale oil recovery by air flooding were analyzed. The effects of air oxygen content, permeability, gas injection pressure, and fractures on the air flooding effect in shale and crude oil production in pores with different sizes were analyzed. The recovery of shale oil can be greatly improved by injecting air into the depleted shale reservoir, but the oil displacement efficiency and the production degree of different levels of pore throats vary with the injection timing. The higher the air oxygen content and the stronger the low-temperature oxidation, the higher the production degree of pores with different sizes and the higher the shale oil recovery. The higher the permeability and the better the pore throat connectivity, the stronger the fluid flow capacity and the higher the shale oil recovery. As the injection pressure increases, the lower limit of the production degree of pore throats decreases, but gas channeling may occur to cause a premature breakthrough;as a result, the recovery increases and then decreases. Fractures can effectively increase the contact area between gas and crude oil, and increase the air sweep coefficient and matrix oil drainage area by supplying oil to fractures through the matrix, which means that a proper fracturing before air injection can help to improve the oil displacement effect under a reasonable production pressure difference.
基金supported by the National Key R&D Program of China(Grant No.2018YFC1405900)the Major Projects of National Science and Technology(Grant Nos.2016ZX05011-002,2016ZX05027-002-005)+3 种基金the National Natural Science Foundation of China(Grant No.41806073)the Natural Science Foundation of Shandong Province(Grant No.ZR2017BD014)Shandong Provincial Key Laboratory of Depositional Mineralization and Sedimentary Minerals,Shandong University of Science and Technology(Grant No.DMSM2017042)the Fundamental Research Funds for the Central Universities(Grant No.201964016)
文摘To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.
基金Supported by the National Natural Science Foundation of China (41330319 and 42072174)Foundation of China University of Petroleum Beijing (2462020XKBH016)Fellowship of China Postdoctoral Science Foundation (2020M680030)。
文摘A micro-nano pore three-dimensional visualized real-time physical simulation of natural gas charging, in-situ pore-scale computation, pore network modelling, and apparent permeability evaluation theory were used to investigate laws of gas and water flow and their distribution, and controlling factors during the gas charging process in low-permeability(tight) sandstone reservoir. By describing features of gas-water flow and distribution and their variations in the micro-nano pore system, it is found that the gas charging in the low permeability(tight) sandstone can be divided into two stages, expansion stage and stable stage. In the expansion stage, the gas flows continuously first into large-sized pores then small-sized pores, and first into centers of the pores then edges of pores;pore-throats greater than 20 μm in radius make up the major pathway for gas charging. With the increase of charging pressure, movable water in the edges of large-sized pores and in the centers of small pores is displaced out successively. Pore-throats of 20-50 μm in radius and pore-throats less than 20 μm in radius dominate the expansion of gas charging channels at different stages of charging in turn, leading to reductions in pore-throat radius, throat length and coordination number of the pathway, which is the main increase stage of gas permeability and gas saturation. Among which, pore-throats 30-50 μm in radius control the increase pattern of gas saturation. In the stable stage, gas charging pathways have expanded to the maximum, so the pathways keep stable in pore-throat radius, throat length, and coordination number, and irreducible water remains in the pore system, the gas phase is in concentrated clusters, while the water phase is in the form of dispersed thin film, and the gas saturation and gas permeability tend stable. Connected pore-throats less than 20 μm in radius control the expansion limit of the charging pathways, the formation of stable gas-water distribution, and the maximum gas saturation. The heterogeneity of connected pore-throats affects the dynamic variations of gas phase charging and gas-water distribution. It can be concluded that the pore-throat configuration and heterogeneity of the micro-nanometer pore system control the dynamic variations of the low-permeability(tight) sandstone gas charging process and gas-water distribution features.
基金funded by the National Natural Science Foundation of China(41974146,42074134)the Graduate Innovation Project of China University of Petroleum(East China)(YCX2021005)。
文摘Due to the tremendous amount of high-resolution measurement information,array laterolog is widely used in evaluations of deviated anisotropic reservoirs.However,the precision of a complementary numerical simulation should be improved as high as the core of fine-scale reservoir evaluation.Therefore,the 3D finite element method(3D-FEM)is presented to simulate the array laterolog responses.Notably,a downscaled physical simulation system is introduced to validate and calibrate the precision of the 3D-FEM.First,the size of the downscaled system is determined by COMSOL.Then,the surrounding and investigated beds are represented by a sodium chloride solution and planks soaked in solution,respectively.Finally,a half-space measurement scheme is presented to improve the experimental efficiency.Moreover,the corresponding sensitivity function and separation factor are established to analyze the effects of the formation anisotro py and dipping angle on the array laterolog responses.The numerical and experimental results indicate that the half-space method is practical,and the mean relative error between the numerical and experimental results is less than 5%,which indicates that the numerical simulation is accurate.With the proposed approach,the reversal angle of array laterolog response curves in anisotropic formations can be observed,and this range is determined to be 50°-62°.
文摘The shear behavior of backfill-rock composites is crucial for mine safety and the management of surface subsidence.For exposing the shear failure mechanism of backfill-rock composites,we conducted shear tests on backfill-rock composites under three constant normal loads,compared with the unfilled rock.To investigate the macro-and meso-failure characteristics of the samples in the shear tests,the cracking behavior of samples was recorded by a high-speed camera and acoustic emission monitoring.In parallel with the experimental test,the numerical models of backfill-rock composites and unfilled rock were established using the discrete element method to analyze the continuous-discontinuous shearing process.Based on the damage mechanics and statistics,a novel shear constitutive model was proposed to describe mechanical behavior.The results show that backfill-rock composites had a special bimodal phenomenon of shearing load-deformation curve,i.e.the first shearing peak corresponded to rock break and the second shearing peak induced by the broken of aeolian sand-cement/fly ash paste backfill.Moreover,the shearing characteristic curves of the backfill-rock composites could be roughly divided into four stages,i.e.the shear failure of the specimens experienced:stage I:stress concentration;stage II:crack propagation;stage III:crack coalescence;stage IV:shearing friction.The numerical simulation shows that the existence of aeolian sand-cement/fly ash paste backfill inevitably altered the coalescence type and failure mode of the specimens and had a strengthening effect on the shear strength of backfillrock composites.Based on damage mechanics and statistics,a shear constitutive model was proposed to describe the shear fracture characteristics of specimens,especially the bimodal phenomenon.Finally,the micro-and meso-mechanisms of shear failure were discussed by combining the micro-test and numerical results.The research can advance the better understanding of the shear behavior of backfill-rock composites and contribute to the safety of mining engineering.
基金supported by the National Natural Science Foundation of China(U1508217,U1702253 and 51774078)the Fundamental Research Funds for the Central Universities(N172506009 and N170908001).
文摘In order to increase the contact area and promote the mass transfer process of gas and liquid,the process of the bubble refine-ment in a metallurgical reactor with mechanical agitation was studied by physical simulation.Based on the capillary number,a prediction equation for the bubble refinement was established.The effects of the gas flow rate,the stirring speed and thestirring depth on the bubble refinement in the reactor were discussed in detail.The distribution of the bubble diameter in thereactor was obtained under different conditions.The results show that when the stirring speed reaches 300 r/min,the bubblediamcter mainly distributes in the range of 1-2 mm.A higher gas flow rate may increase the number of bubbles in the meltand promote the bubble refinement process.The mechanism of bubble refinement under mechanical agitation was analyzed.and the results indicated that the stirring speed.,the blade area and the blade inclination are the main influencing factors.
基金The work was supported by the National Science and Technology Major Project(2016ZX05062,2017ZX05037-001).
文摘The ultra-low porosity and permeability,as well as complex occurrence and transport state of shale reservoir make it possess special L-type production characteristic curve and complicated shale gas flow mechanism.To solve the difficulty of collecting complete production data due to short production time and operation discontinuity,a full-diameter core physical simulation experiment on the full lifecycle production process of shale gas well depletion is conducted with the purpose of obtaining many important production data including complete pressure and daily gas output in the simulated production process of shale gas well.The experimental results show the production characteristic from simulation is consistent with those from gas well.Based on the simulation data,the critical desorption pressure(12 MPa)of core,free gas production(3820.8 mL),adsorbed gas production(2151.2 mL),the proportion of the daily gas production between free and absorbed gas under different time and formation pressure,as well as the production time and final recovery rate corresponding to abandoned pressure,can be determined accurately.Numerical inversion is carried out to calculate the production performance curve of shale gas well and predict the development effect of gas well based on well testing and similarity analysis of the dimensionless time between core experiment and gas well production.Finally,the permeability and the fracturing effect(fracture network density)as the keys to the effective development of shale gas reservoirs are proposed.The permeability is the fundamental factor and the fracturing technology is the major means.
基金Supported by PetroChina Science and Technology Project(2021DJ0202).
文摘Considering the action mechanisms of overpressure on physical changes in skeleton particles of deep reservoir rocks and the differences in physical changes of skeleton particles under overpressure and hydrostatic pressure, the sandstone of the Jurassic Toutunhe Formation in the southern margin of Junggar Basin was taken as an example for physical modeling experiment to analyze the action mechanisms of overpressure on the physical properties of deep reservoirs. (1) In the simulated ultra-deep layer with a burial depth of 6000-8000 m, the mechanical compaction under overpressure reduces the remaining primary pores by about a half that under hydrostatic pressure. Overpressure can effectively suppress the mechanical compaction to allow the preservation of intergranular primary pores. (2) The linear contact length ratio under overpressure is always smaller than the linear contact length ratio under hydrostatic pressure at the same depth. In deep reservoirs, the difference between the mechanical compaction degree under overpressure and hydrostatic pressure shows a decreasing trend, the effect of abnormally high pressure to resist the increase of effective stress is weakened, and the degree of mechanical compaction is gradually close to that under hydrostatic pressure. (3) The microfractures in skeleton particles of deep reservoirs under overpressure are thin and long, while the microfractures in skeleton particles of deep reservoirs under hydrostatic pressure are short and wide. This difference is attributed to the probable presence of tension fractures in the rocks containing abnormally high pressure fluid. (4) The microfractures in skeleton particles under overpressure were mainly formed later than that under hydrostatic pressure, and the development degree and length of microfractures both extend deeper. (5) The development stages of microfractures under overpressure are mainly controlled by the development stages of abnormally high pressure and the magnitude of effective stress acting on the skeleton particles. Moreover, the development stages of microfractures in skeleton particles are more than those under hydrostatic pressure in deep reservoir. The multi-stage abnormally high pressure plays an important role in improving the physical properties of deep reservoirs.
文摘A model of binding forces in metals and alloys, based on the density functional theory and accounted effects of the many-body interactions, was proposed. The developed method can be easily applied for study of metals and alloys by the molecular dynamics simulation. The potentials of interatomic interactions have been found by the proposed method and applied for calculations of equation of state, elastic moduli and phonon dispersion in metals Ni, Al, alloys NiAl and Ni3Al. Results of the calculations are in good agreement with known experimental data both for pure metals and alloys.
文摘The dual transmitter implements the equivalent anti-magnetic flux transient electromagnetic method, which can effectively reduce the scope of the transient electromagnetic detection blind area. However, this method is rarely reported in the detection of pipelines in urban geophysical exploration and the application of coal mines. Based on this, this paper realizes the equivalent anti-magnetic flux transient electromagnetic method based on the dual launcher. The suppression effect of this method on the blind area is analyzed by physical simulation. And the detection experiment of underground pipelines is carried out outdoors. The results show that the dual launcher can significantly reduce the turn-off time, thereby effectively reducing the impact of the blind area on the detection results, and the pipeline detection results verify the device’s effectiveness. Finally, based on the ground experimental results, the application prospect of mine advanced detection is discussed. Compared with other detection fields, the formation of blind areas is mainly caused by the equipment. If the dual launcher can be used to reduce the blind area, the accuracy of advanced detection can be improved more effectively. The above research results are of great significance for improving the detection accuracy of the underground transient electromagnetic method.
文摘In fog, visibility is reduced. This reduction in visibility is measured by the meteorological optical range (MOR), which is important for studying human perception and various sensors in foggy conditions. The Cerema PAVIN Fog & Rain platform is capable of producing calibrated fog in order to better analyses it and understand its consequences. The problem is that the droplets produced by the platform are not large enough to resemble real fog. This can have a major impact on measurements since the interaction between electromagnetic waves and fog depends on the wavelength and diameter of the droplets. To remedy this, Cerema is building a new platform with new equipment capable of generating fog. This study analyses different nozzles and associated usage parameters such as the type of water used and the pressure used. The aim is to select the best nozzle with the associated parameters for producing large-diameter droplets and therefore more realistic fog.
基金This work is financially supported by the National Natural Science Foundation Project(No.51374222)National Major Project(No.2017ZX05032004-002)+2 种基金the National Key Basic Research&Development Program(No.2015CB250905)CNPC’s Major Scientific and Technological Project(No.2017E-0405)SINOPEC Major Scientific Research Project(No.P18049-1).
文摘Stress sensitivity is a very important index to understand the seepage characteristics of a reservoir.In this study,dedicated experiments and theoretical arguments based on the visualization of porous media are used to assess the effects of the fracture angle,spacing,and relevant elastic parameters on the principal value of the permeability tensor.The fracture apertures at different angles show different change rates,which influence the relative permeability for different sets of fractures.Furthermore,under the same pressure condition,the fractures with different angles show different degrees of deformation so that the principal value direction of permeability rotates.This phenomenon leads to a variation in the water seepage direction in typical water-injection applications,thereby hindering the expected exploitation effect of the original well network.Overall,the research findings in this paper can be used as guidance to improve the effectiveness of water injection exploitation in the oil field industry.
基金This project was funded by Natural Science Foundation of Guangdong Province,No.2020B010165004。
文摘Deep simulations have gained widespread attention owing to their excellent acceleration performances.However,these methods cannot provide effective collision detection and response strategies.We propose a deep interac-tive physical simulation framework that can effectively address tool-object collisions.The framework can predict the dynamic information by considering the collision state.In particular,the graph neural network is chosen as the base model,and a collision-aware recursive regression module is introduced to update the network parameters recursively using interpenetration distances calculated from the vertex-face and edge-edge tests.Additionally,a novel self-supervised collision term is introduced to provide a more compact collision response.This study extensively evaluates the proposed method and shows that it effectively reduces interpenetration artifacts while ensuring high simulation efficiency.
基金Supported by the National Science and Technology Major Project of China(2016ZX05046-001).
文摘Based on the typical dissection of various onshore tight oil fields in China,the tight oil migration and accumulation mechanism and enrichment-controlling factors in continental lake basins are analyzed through nuclear magnetic resonance(NMR)displacement physical simulation and Lattice Boltzmann numerical simulation by using the samples of source rock,reservoir rock and crude oil.In continental lake basins,the dynamic forces driving hydrocarbon generation and expulsion of high-quality source rocks are the foundational power that determines the charging efficiency and accumulation effect of tight oil,the oil migration resistance is a key element that influences the charging efficiency and accumulation effect of tight oil,and the coupling of charging force with pore-throat resistance in tight reservoir controls the tight oil accumulation and sweet spot enrichment.The degree of tight oil enrichment in continental lake basins is controlled by four factors:source rock,reservoir pore-throat size,anisotropy of reservoir structure,and fractures.The high-quality source rocks control the near-source distribution of tight oil,reservoir physical properties and pore-throat size are positively correlated with the degree of tight oil enrichment,the anisotropy of reservoir structure reveals that the parallel migration rate is the highest,and intralayer fractures can improve the migration and accumulation efficiency and the oil saturation.
基金Supported by the National Natural Scienceof China (41872113,42172109,42172108)National Key R&D Plan Project (2018YFA0702405)+1 种基金Special Science and Technology Program for Strategic Cooperation Between China National Petroleum Corporation and China University of Petroleum (Beijing)(ZLZX2020-02)China University of Petroleum (Beijing) Research Initiation Fund Project (2462020BJRC002,2462020YXZZ020)。
文摘Constrained by the geological burial history of Cretaceous Qingshuihe Formation in the southern margin of Junggar Basin, the diagenetic physical simulation experiment was carried out with the low-mature sandstone samples taken from the outcrop area. Then, coupling with the regional geological data, the reformation of reservoirs with different diagenetic intensities by microfractures and the significance of microfractures for development of high-quality reservoirs were discussed. The results show that the large-scale microfractures were formed in the stage of late rapid deep burial, roughly equivalent to the period when organic acids were filled. The microfractures created good conditions for migration of oil and gas in deep and ultra-deep clastic rocks, and also enabled the transport of organic acids to the reservoirs for ensuing the late continuous dissolution of cements and particles. The existence of matrix pores and microfractures in the reservoirs before the rapid deep burial determined how the microfractures formed during rapid deep burial improved the reservoir quality. If matrix pores and microfractures were more developed and the cementation degree was lower before the rapid deep burial, the microfractures would be more developed and the dissolution degree would be higher during the late rapid deep burial, and so the reservoir quality would be improved more greatly, which can increase the reservoir permeability by up to 55%. If cementation was very strong, but matrix pores were not developed and microfractures existed locally before the rapid deep burial, the microfractures would also be more developed during the late rapid deep burial, which can increase the reservoir permeability by 43%. If cementation was strong, matrix pores were absent, and microfractures were not developed, limited microfractures would be formed during the late rapid deep burial, which can increase the reservoir permeability by only 16%. Formation of large-scale microfractures during late rapid deep burial and promotion of such microfractures to the dissolution of organic acids are considered as key diagenetic factors for the development of deep and ultra-deep high-quality reservoirs.
基金The authors gratefully acknowledge the financial support from the National Science and Technology Major Project of China(Grant Nos.2017ZX05013-001 and 2017ZX05069-003).
文摘Given its relevance to the exploitation of ultra-low permeability reservoirs,which account for a substantial proportion of the world’s exploited and still unexploited reserves,in the present study the development of an adequate water injection system is considered.Due to the poor properties and weak seepage capacity of these reservoirs,the water injection pressure typically increases continuously during water flooding.In this research,the impact on such a process of factors as permeability,row spacing,and pressure gradient is evaluated experimentally using a high-pressure large-scale outcrop model.On this basis,a comprehensive evaluation coefficient is introduced able to account for the effective driving pressure.
基金financial support from the National Science and Technology Major Project (2017ZX05013-001, 2017ZX05069003, 2017ZX05049005-004)Ministry of Science and Technology of PetroChina (2021ZZ01-03, kt2021-09-05, 2021DJ1806, 2017E-1514, 2018E-11-05)。
文摘Combined with NMR,core experiment,slim-tube tests,nano-CT and oil composition analysis,the mechanism of CO(2) enhanced oil recovery had been studied.CO_(2) flooding under supercritical state could achieve higher oil recovery.In the process of crude oil displaced by supercritical CO2,the average oil recovery was 46.98% at low displacement pressures and 73.35% at high displacement pressures.The permeability of cores after CO2 flooding was only 28%-64% of those before flooding.As to the expelled oil,the contents of asphaltenes and non-hydrocarbons decreased,and saturated hydrocarbons of above C25 were absent in some samples,indicating that they had been retained in cores as demonstrated by CT and NMR experiments.In slim-tube tests,the heavy components of oil were expelled when the pressure increased to 30 MPa.There was a reasonable bottom hole pressure(BHP) below which the heavy components driven out from the far-well zone would deposit in the near-well zone,and when the pressure was too high,the nonhydrocarbon detention may cause block.The smaller throat and worse physical properties the porous media had,the higher displacement pressure would be required to achieve a good oil displacement efficiency.The increase in displacement pressure or time of interaction between oil and CO2 could effectively enhance oil recovery.