The upper part of the Fujia deposit was mined out by open-pit, and the lower part is being mined underground. The level pillar between open-pit and underground mine had a thickness of 24 m, a length of 300 m and a max...The upper part of the Fujia deposit was mined out by open-pit, and the lower part is being mined underground. The level pillar between open-pit and underground mine had a thickness of 24 m, a length of 300 m and a maximum width of 35 in. As the level pillar contained about 5.2 million ton ore of high nickel grade, it was necessary to recover the level pillar. Because of special need of safety, underhand heading cut-and-fill stoping method was used. For the first two layers of heading, the cemented fill materials were a mix of water and high-aluminum-content cement with silicate gelling agent; and for other heading layers, total tailings was added into the fill mix in order to reduce the cement consumption. Finally, the level pillar was recovered successfully.展开更多
With the third innovation in science and technology worldwide, China has also experienced thismarvelous progress. Concerning the longwall mining in China, the ＂masonry beam theory＂ （MBT） wasfirst proposed in the 1...With the third innovation in science and technology worldwide, China has also experienced thismarvelous progress. Concerning the longwall mining in China, the ＂masonry beam theory＂ （MBT） wasfirst proposed in the 1960s, illustrating that the transmission and equilibrium method of overburdenpressure using reserved coal pillar in mined-out areas can be realized. This forms the so-called ＂121mining method＂, which lays a solid foundation for development of mining science and technology inChina. The ＂transfer rock beam theory＂ （TRBT） proposed in the 1980s gives a further understanding forthe transmission path of stope overburden pressure and pressure distribution in high-stress areas. In thisregard, the advanced 121 mining method was proposed with smaller coal pillar for excavation design,making significant contributions to improvement of the coal recovery rate in that era. In the 21st century,the traditional mining technologies faced great challenges and, under the theoretical developmentspioneered by Profs. Minggao Qian and Zhenqi Song, the ＂cutting cantilever beam theory＂ （CCBT） wasproposed in 2008. After that the 110 mining method is formulated subsequently, namely one stope face,after the first mining cycle, needs one advanced gateway excavation, while the other one is automaticallyformed during the last mining cycle without coal pillars left in the mining area. This method can beimplemented using the CCBT by incorporating the key technologies, including the directional presplittingroof cutting, constant resistance and large deformation （CRLD） bolt/anchor supporting systemwith negative Poisson＇s ratio （NPR） effect material, and remote real-time monitoring technology. TheCCBT and 110 mining method will provide the theoretical and technical basis for the development ofmining industry in China.展开更多
The EGAT Mae Moh Mine is the largest open pit lignite mine in Thailand and it produces lignite about 16 million tons annually. In the near future, the pit limit of the mine will be reached and underground mine will th...The EGAT Mae Moh Mine is the largest open pit lignite mine in Thailand and it produces lignite about 16 million tons annually. In the near future, the pit limit of the mine will be reached and underground mine will then be developed through the open pit in the depth of 400 - 600 m from the surface. However, due to the challenges for underground mining such as poor geological conditions, extra thickness (20 - 30 m) of coal seams, and weak mechanical properties of coal seams and the surrounding rock, the success possibility of underground mining and an applicable underground mining method is being investigated at the present. The paper discusses the applicability of multi-slice bord-and-pillar method for the soft extra thick coal seams in the Mae Moh mine by means of numerical analyses using the 3D finite difference code “FLAC3D”.展开更多
Thirty years ago, the analysis of longwall pillar stability(ALPS) inaugurated a new era in coal pillar design.ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full ex...Thirty years ago, the analysis of longwall pillar stability(ALPS) inaugurated a new era in coal pillar design.ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of longwall mining case histories.ALPS was followed by the analysis of retreat mining stability(ARMPS) and the analysis of multiple seam stability(AMSS). These methods incorporated other innovations, including the coal mine roof rating(CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However,the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example,in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice. The analysis of coal pillar stability(ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery.ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.展开更多
This paper attempts to investigate the use of approximate 2D numerical simulation techniques for the evaluation of lignite pillar geomechanical response, formed via the room and pillar mining method.Performance and ap...This paper attempts to investigate the use of approximate 2D numerical simulation techniques for the evaluation of lignite pillar geomechanical response, formed via the room and pillar mining method.Performance and applicability of the developing methodology are assessed through benchmarking with a more direct and accurate 3D numerical model. This analysis utilizes an underground lignite mine which is being developed in soft rock environment. Through the decisions made for the optimum room and pillar layout, the design process highlights the strong points and the weaknesses of 2D finite element analysis, and provides useful recommendations for future reference. The interpretations of results demonstrate that 2D approximation techniques come near quite well to the actual 3D problem.However, external load approximation technique seems to fit even better with the respective outcomes from the 3D analyses.展开更多
In this paper, the coupled thermo-mechanical （TM） processes in the AEspoe Pillar Stability Experiment （APSE） carried out by the Swedish Nuclear Fuel and Waste Management Company （SKB） were simulated using both c...In this paper, the coupled thermo-mechanical （TM） processes in the AEspoe Pillar Stability Experiment （APSE） carried out by the Swedish Nuclear Fuel and Waste Management Company （SKB） were simulated using both continuum and discontinuum based numerical methods. Two-dimensional （2D） and three- dimensional （3D） finite element method （FEM） and 2D distinct element method （DEM） with particles were used. The main objective for the large scale in situ experiment is to investigate the yielding strength of crystalline rock and the formation of the excavation disturbed/damaged zone （EDZ） during excavation of two boreholes, pressurizing of one of the boreholes and heating. For the DEM simulations, the heat flow algorithm was newly introduced into the original code. The calculated stress, displacement and temperature distributions were compared with the ones obtained from in situ measurements and FEM simulations. A parametric study for initial microcracks was also performed to reproduce the spalling phenomena observed in the APSE.展开更多
文摘The upper part of the Fujia deposit was mined out by open-pit, and the lower part is being mined underground. The level pillar between open-pit and underground mine had a thickness of 24 m, a length of 300 m and a maximum width of 35 in. As the level pillar contained about 5.2 million ton ore of high nickel grade, it was necessary to recover the level pillar. Because of special need of safety, underhand heading cut-and-fill stoping method was used. For the first two layers of heading, the cemented fill materials were a mix of water and high-aluminum-content cement with silicate gelling agent; and for other heading layers, total tailings was added into the fill mix in order to reduce the cement consumption. Finally, the level pillar was recovered successfully.
基金supported by the National Natural Science Foundation of China (No. 51404278)the State Key Program of National Natural Science Foundation of China (No. 51134005)
文摘With the third innovation in science and technology worldwide, China has also experienced thismarvelous progress. Concerning the longwall mining in China, the ＂masonry beam theory＂ （MBT） wasfirst proposed in the 1960s, illustrating that the transmission and equilibrium method of overburdenpressure using reserved coal pillar in mined-out areas can be realized. This forms the so-called ＂121mining method＂, which lays a solid foundation for development of mining science and technology inChina. The ＂transfer rock beam theory＂ （TRBT） proposed in the 1980s gives a further understanding forthe transmission path of stope overburden pressure and pressure distribution in high-stress areas. In thisregard, the advanced 121 mining method was proposed with smaller coal pillar for excavation design,making significant contributions to improvement of the coal recovery rate in that era. In the 21st century,the traditional mining technologies faced great challenges and, under the theoretical developmentspioneered by Profs. Minggao Qian and Zhenqi Song, the ＂cutting cantilever beam theory＂ （CCBT） wasproposed in 2008. After that the 110 mining method is formulated subsequently, namely one stope face,after the first mining cycle, needs one advanced gateway excavation, while the other one is automaticallyformed during the last mining cycle without coal pillars left in the mining area. This method can beimplemented using the CCBT by incorporating the key technologies, including the directional presplittingroof cutting, constant resistance and large deformation （CRLD） bolt/anchor supporting systemwith negative Poisson＇s ratio （NPR） effect material, and remote real-time monitoring technology. TheCCBT and 110 mining method will provide the theoretical and technical basis for the development ofmining industry in China.
文摘The EGAT Mae Moh Mine is the largest open pit lignite mine in Thailand and it produces lignite about 16 million tons annually. In the near future, the pit limit of the mine will be reached and underground mine will then be developed through the open pit in the depth of 400 - 600 m from the surface. However, due to the challenges for underground mining such as poor geological conditions, extra thickness (20 - 30 m) of coal seams, and weak mechanical properties of coal seams and the surrounding rock, the success possibility of underground mining and an applicable underground mining method is being investigated at the present. The paper discusses the applicability of multi-slice bord-and-pillar method for the soft extra thick coal seams in the Mae Moh mine by means of numerical analyses using the 3D finite difference code “FLAC3D”.
文摘Thirty years ago, the analysis of longwall pillar stability(ALPS) inaugurated a new era in coal pillar design.ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of longwall mining case histories.ALPS was followed by the analysis of retreat mining stability(ARMPS) and the analysis of multiple seam stability(AMSS). These methods incorporated other innovations, including the coal mine roof rating(CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However,the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example,in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice. The analysis of coal pillar stability(ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery.ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.
文摘This paper attempts to investigate the use of approximate 2D numerical simulation techniques for the evaluation of lignite pillar geomechanical response, formed via the room and pillar mining method.Performance and applicability of the developing methodology are assessed through benchmarking with a more direct and accurate 3D numerical model. This analysis utilizes an underground lignite mine which is being developed in soft rock environment. Through the decisions made for the optimum room and pillar layout, the design process highlights the strong points and the weaknesses of 2D finite element analysis, and provides useful recommendations for future reference. The interpretations of results demonstrate that 2D approximation techniques come near quite well to the actual 3D problem.However, external load approximation technique seems to fit even better with the respective outcomes from the 3D analyses.
基金conducted within the context of the international DECOVALEX Project (DEvelopment of COupled models and their VALidation against EXperiments)financed by Japan Atomic Energy Agency (JAEA) who was also one of the Funding Organizations of the projectChrister Anders-son from Swedish Nuclear Fuel and Waste Management Co.(SKB),Sweden
文摘In this paper, the coupled thermo-mechanical （TM） processes in the AEspoe Pillar Stability Experiment （APSE） carried out by the Swedish Nuclear Fuel and Waste Management Company （SKB） were simulated using both continuum and discontinuum based numerical methods. Two-dimensional （2D） and three- dimensional （3D） finite element method （FEM） and 2D distinct element method （DEM） with particles were used. The main objective for the large scale in situ experiment is to investigate the yielding strength of crystalline rock and the formation of the excavation disturbed/damaged zone （EDZ） during excavation of two boreholes, pressurizing of one of the boreholes and heating. For the DEM simulations, the heat flow algorithm was newly introduced into the original code. The calculated stress, displacement and temperature distributions were compared with the ones obtained from in situ measurements and FEM simulations. A parametric study for initial microcracks was also performed to reproduce the spalling phenomena observed in the APSE.
