Laying head is a high-precision engineering device in hot-rolled high speed wire rod production line. Previously research works are focused on the laying pipe wear-resisting. Laying pipe curve design method based on w...Laying head is a high-precision engineering device in hot-rolled high speed wire rod production line. Previously research works are focused on the laying pipe wear-resisting. Laying pipe curve design method based on wire rod kinematics and dynamics analyses are not reported before. In order to design and manufacture the laying pipe, the motion and force process of the wire rod in the laying pipe should be studied. In this paper, a novel approach is proposed to investigate the force modeling for hot-rolled wire rod in laying pipe. An idea of limited element method is used to analysis and calculates the forces between laying pipe inner surface and wire rod. The design requirements of laying pipe curve for manufacturing are discussed. The kinematics and dynamics modeling for numerical calculation are built. A laying pipe curve equation is proposed by discussing design boundary conditions. Numerical results with di erent laying pipe curves design parameters are plotted and compared. The proposed approach performs good result which can be applied for laying pipe curve design and analysis for engineering application.展开更多
NOx and soot emissions from diesel engines can be greatly reduced by pressure wave supercharging(PWS).The diesel engine matched with PWS needs redesigning its exhaust pipes.Except for meeting the installation requirem...NOx and soot emissions from diesel engines can be greatly reduced by pressure wave supercharging(PWS).The diesel engine matched with PWS needs redesigning its exhaust pipes.Except for meeting the installation requirements,the exhaust gas must be stable in pressure before rushing into PWS.In this paper the lateral and center ported divergent exhaust pipes are designed,modeled geometrically and analyzed structurally based on a 3-D design software-CATIA to determine the structure of two exhaust pipes having the required inner volume.Then flow analysis for two exhaust pipes is done using a flow analysis software-ANASYS.Moreover,the optimal exhaust pipes are determined comprehensively and cast for engine test.Engine test results show that PWS is superior to turbocharging at low engine speeds and inferior to turbocharging in power and emissions at medium-to-high engine speeds.The performance of PWS engine under high speed operating conditions can be improved by contriving larger surge volume intake and exhaust pipes.展开更多
The Beijing spectrometer Ⅲ （BESⅢ） beam pipe is in the center of the BESⅢ, which is the detector of the upgrade project of Beijing electron and positron collider （BEPC Ⅱ）. Electrons and positrons collide in the...The Beijing spectrometer Ⅲ （BESⅢ） beam pipe is in the center of the BESⅢ, which is the detector of the upgrade project of Beijing electron and positron collider （BEPC Ⅱ）. Electrons and positrons collide in the BESⅢ beam pipe. According to the demands of the BEPC Ⅱ, a key program of Chinese Academy of Sciences, the BESⅢ beam pipe is designed based on the finite elements analysis. The BESIII beam pipe is installed in the inner cylinder of the BESⅢ drift chamber. As a vacuum tube, the BESIII beam pipe is designed as 1 000 mm in length, 63 mm in inner diameter and 114 mm in outer diameter, respectively. The BESIII beam pipe consists of a central beryllium pipe cooled by EDM-1, the oil No.1 for electric discharge machining, and two extended copper pipes cooled by deionized water （DW）. The three parts are jointed by vacuum welding. Factors taken into account in the design are as follows. ① The wall thickness of the central beryllium pipe should be designed as small as possible to reduce the multi-scattering and improve the particle momentum resolution. And the wall thickness of the extended copper pipe should be designed as large as possible to protect the detectors from the backgrounds. ②The BESⅢ beam pipe must be sufficiently cooled to avoid the damage and prevents its influence to the BESⅢ drift chamber （DC） operation. The inner surface temperature of the DC inner cylinder must be maintained at 293±2 K. ③ The magnetic permeability of the materials used in the BESⅢ beam pipe must be less than 1.05 H/m to avoid large magnetic field distortions. ④ The static pressure of the vacuum chamber of the BESⅢ beam pipe must be less than 800 μPa. The simulating results show that the designed structure of the BESⅢ beam pipe satisfies the requirements mentioned above. The structure design scheme is evaluated and adonted hv the headouarters of BEPCⅡ.展开更多
Satellite＇s thermal control subsystem （TCS） has to maintain components and structure within their specified temperature limits during satellite service life. TCS designers have to face the challenge of reducing bot...Satellite＇s thermal control subsystem （TCS） has to maintain components and structure within their specified temperature limits during satellite service life. TCS designers have to face the challenge of reducing both the weight of the system and required heater power while keeping components temperature within their design range. For a space based heat pipe radiator system, several researchers have published different approaches to reach such goal. This paper presents a thermal design and optimization of a heat pipe radiator applied to a practical engineering design application. For this study, a prospective communication satellite payload panel with applied passive thermal control techniques was considered. The thermal passive techniques used in this design mainly include multilayer insulation （MLI） blankets, optical solar reflectors （OSR）, selected thermal coatings, interface fillers and constant conductance heat pipes. The heat pipe network is comprised of some heat pipes embedded in the panel and some mounted on inner surface of the panel. Embedded heat pipes are placed under high heat dissipation equipments and their size is fixed; minimum weight of the radiator is achieved by a minimum weight of the mounted heat pipes. Hence, size of the mounted heat pipes is optimized. A thermal model was built and parameterized for transient thermal analysis and optimization. Temperature requirements of components in both worst case conditions （Hot case and cold case） were satisfied under optimal sizing of mounted heat pipes.展开更多
Combining real accelerating genetic algorithm(RAGA) with the optimization design of multi-hole and varied diameter pipe, the authors solved the problem of optimizing multi-dimensional parameters at the same time. In w...Combining real accelerating genetic algorithm(RAGA) with the optimization design of multi-hole and varied diameter pipe, the authors solved the problem of optimizing multi-dimensional parameters at the same time. In which the advanced convergence and easily to run into partial optimization were avoid. Applied the RAGA to solving the problem in the optimization design of fixed piping sprinkler irrigation system. The optimized parameters, such as diameters and the length of pipe were calculated and the result was reasonable, which provides as a reference to readers who work at related research.展开更多
基金China Postdoctoral Science Foundation Project(Grant No.2017M611184)
文摘Laying head is a high-precision engineering device in hot-rolled high speed wire rod production line. Previously research works are focused on the laying pipe wear-resisting. Laying pipe curve design method based on wire rod kinematics and dynamics analyses are not reported before. In order to design and manufacture the laying pipe, the motion and force process of the wire rod in the laying pipe should be studied. In this paper, a novel approach is proposed to investigate the force modeling for hot-rolled wire rod in laying pipe. An idea of limited element method is used to analysis and calculates the forces between laying pipe inner surface and wire rod. The design requirements of laying pipe curve for manufacturing are discussed. The kinematics and dynamics modeling for numerical calculation are built. A laying pipe curve equation is proposed by discussing design boundary conditions. Numerical results with di erent laying pipe curves design parameters are plotted and compared. The proposed approach performs good result which can be applied for laying pipe curve design and analysis for engineering application.
文摘NOx and soot emissions from diesel engines can be greatly reduced by pressure wave supercharging(PWS).The diesel engine matched with PWS needs redesigning its exhaust pipes.Except for meeting the installation requirements,the exhaust gas must be stable in pressure before rushing into PWS.In this paper the lateral and center ported divergent exhaust pipes are designed,modeled geometrically and analyzed structurally based on a 3-D design software-CATIA to determine the structure of two exhaust pipes having the required inner volume.Then flow analysis for two exhaust pipes is done using a flow analysis software-ANASYS.Moreover,the optimal exhaust pipes are determined comprehensively and cast for engine test.Engine test results show that PWS is superior to turbocharging at low engine speeds and inferior to turbocharging in power and emissions at medium-to-high engine speeds.The performance of PWS engine under high speed operating conditions can be improved by contriving larger surge volume intake and exhaust pipes.
基金Key Programs of Chinese Academy of Sciences(No.KJ95T-03)
文摘The Beijing spectrometer Ⅲ （BESⅢ） beam pipe is in the center of the BESⅢ, which is the detector of the upgrade project of Beijing electron and positron collider （BEPC Ⅱ）. Electrons and positrons collide in the BESⅢ beam pipe. According to the demands of the BEPC Ⅱ, a key program of Chinese Academy of Sciences, the BESⅢ beam pipe is designed based on the finite elements analysis. The BESIII beam pipe is installed in the inner cylinder of the BESⅢ drift chamber. As a vacuum tube, the BESIII beam pipe is designed as 1 000 mm in length, 63 mm in inner diameter and 114 mm in outer diameter, respectively. The BESIII beam pipe consists of a central beryllium pipe cooled by EDM-1, the oil No.1 for electric discharge machining, and two extended copper pipes cooled by deionized water （DW）. The three parts are jointed by vacuum welding. Factors taken into account in the design are as follows. ① The wall thickness of the central beryllium pipe should be designed as small as possible to reduce the multi-scattering and improve the particle momentum resolution. And the wall thickness of the extended copper pipe should be designed as large as possible to protect the detectors from the backgrounds. ②The BESⅢ beam pipe must be sufficiently cooled to avoid the damage and prevents its influence to the BESⅢ drift chamber （DC） operation. The inner surface temperature of the DC inner cylinder must be maintained at 293±2 K. ③ The magnetic permeability of the materials used in the BESⅢ beam pipe must be less than 1.05 H/m to avoid large magnetic field distortions. ④ The static pressure of the vacuum chamber of the BESⅢ beam pipe must be less than 800 μPa. The simulating results show that the designed structure of the BESⅢ beam pipe satisfies the requirements mentioned above. The structure design scheme is evaluated and adonted hv the headouarters of BEPCⅡ.
文摘Satellite＇s thermal control subsystem （TCS） has to maintain components and structure within their specified temperature limits during satellite service life. TCS designers have to face the challenge of reducing both the weight of the system and required heater power while keeping components temperature within their design range. For a space based heat pipe radiator system, several researchers have published different approaches to reach such goal. This paper presents a thermal design and optimization of a heat pipe radiator applied to a practical engineering design application. For this study, a prospective communication satellite payload panel with applied passive thermal control techniques was considered. The thermal passive techniques used in this design mainly include multilayer insulation （MLI） blankets, optical solar reflectors （OSR）, selected thermal coatings, interface fillers and constant conductance heat pipes. The heat pipe network is comprised of some heat pipes embedded in the panel and some mounted on inner surface of the panel. Embedded heat pipes are placed under high heat dissipation equipments and their size is fixed; minimum weight of the radiator is achieved by a minimum weight of the mounted heat pipes. Hence, size of the mounted heat pipes is optimized. A thermal model was built and parameterized for transient thermal analysis and optimization. Temperature requirements of components in both worst case conditions （Hot case and cold case） were satisfied under optimal sizing of mounted heat pipes.
文摘Combining real accelerating genetic algorithm(RAGA) with the optimization design of multi-hole and varied diameter pipe, the authors solved the problem of optimizing multi-dimensional parameters at the same time. In which the advanced convergence and easily to run into partial optimization were avoid. Applied the RAGA to solving the problem in the optimization design of fixed piping sprinkler irrigation system. The optimized parameters, such as diameters and the length of pipe were calculated and the result was reasonable, which provides as a reference to readers who work at related research.
