Detection of Bisphenol A (BPA) in Plastic Bottles Using Vertical Cultivation at Various Temperatures

Polycarbonate plastics containing bisphenol A (BPA) used to manufacture drinking water bottles. Kurdistan region in northern Iraq is a developed area with increased pollution from plastic bottles. Trace amounts of BPA have been detected in bottled water samples. The absorption of BPA was measured with HPLC using a vertical cultivation system with Bulbs of the Allium Cepa plant planted in these plastic bottles with monitored growth. Vertical cultivation was found to have a low level of BPA in the plant cells, making it a safe cultivation method under specific climate conditions. The mean concentration of BPA in vertical cultivation is 0.19 ug/ml (3.8 ng for a 20 uL injection), and the Limit of Quantification (LOQ) is 0.63 ug/ml (12.7 ng for 20 uL injection). While Scanning Electron Microscope (SEM) shows that the concentrations are relatively low in water samples stored at room temperature compared to those exposed to direct sunlight (40°C) and water bottle samples stored at (-4°C), The correlation coefficients were found to be good (0.9992). SEM is used for plastic bottle samples stored at different temperatures. The images identify compound decay and explore the morphology of BPA in manufactured plastic materials.

Influence of the Partial Substitution of Bitumen by a Mixture of Sulphur and Tyre and Plastic Bottle Powders on the Behaviour of Bituminous Concrete

This article deals with the influence of the partial substitution of bitumen by a mixture of sulphur and tyre and plastic bottle powders on the characterization of asphalt concrete. The approach adopted was to subject a control asphalt concrete to level 2 formulation tests as well as those modified at 10%, 20%, 30% and 40% by substituting bitumen with a mixture of tyre powder, plastic bottle powder and sulphur at 40%, 28% and 32% respectively. The results of the PCG, Duriez and rutting tests carried out on the control and modified bituminous concretes (manufactured using the wet process) revealed three (03) major findings, in particular with regard to workability, resistance to simple compression and rutting. The experimental results show an increasing trend in the essential parameters. At 40% substitution, there was a 22.73% increase in compactness, reflecting a significant improvement in the material’s workability. With regard to simple compressive strength, the increase is 34.02% at 40% substitution, highlighting the limitation of crack formation and propagation under heavy precipitation. With regard to rutting, the 16% drop in susceptibility at 40% substitution reflects a significant improvement in the behaviour of the material under dynamic mechanical stresses in heavy precipitation. The improvement in these behaviours results from the insertion of the plastic bottle powder into the interstices of the granular skeleton, thus reducing its cellular structure, and also from the interactions between the sulphur with the tyre powder and the sulphur with the plastic bottle powder, i.e. cross-linking or vulcanisation.

Versatile Plastic Bottles Blowing Machine

The versatile plastic bottle blowing machine, developed and produced by the Anhui Tongda Science and Technology Development Corp. under the Sino-foreign joint venture Guobao Group, has been exported to Britain, Iceland, Paraguay, Thailand, Pakistan, Bangladesh and the Commonwealth of Independent States. At an

A Comparative Study of the Thermal Performance of Plastic Bottle Wall against Traditional Composite Brick Wall Typologies

According to the container recycling institute,nearly a million plastic beverage bottles are sold every minute around the world.Plastic bottles are considered as an urban junk,however,it has shape characteristics which make them usable in construction in lieu of conventional bricks.This research promotes the use of recycled plastic bottles as eco-bricks by substituting it with the typical construction bricks.It evaluates the thermal performance of sand filled plastic bottle-walls in a comparative analysis with traditional composite brick walls.The thermal performance of the plastic bottle walls was evaluated through COMSOL®Multi-physics and the results are noted.

SIMULATION OF EXTRA LIGHT-THIN COMPONENT DEFORMATION WITH ABNORMAL SHAPE

Based on the analyses of the structural feature and the function requirements of newstyle bottle cap, the two fundamental components, the lining washer and the outer body, are abstracted as a plate and a cylinder with thin wall respectively. For simulating the deformation of the lining washer under equiaxial pressure, the modified Lagrangian finite element analysis is applied on the 228 triangular elements. Under assembly pressure, the plastoelastic deformation of both the lining washer and the outer body are studied in terms of Tresca＇s yield criterion and the limitation of the plastic deformation is presented when the two components are assembled into one unit. For the production of this kind of bottle cover, experiments are carried out by carefully measuring the changes of the diameter of lining washer as well as that of the outer body. It is shown that results from the experiments have a good agreement with the theoretical calculation and the maximum value of the allowable pressure has successfully been used in the design of newly developed bottle cap production system.