Semicontinuous equal-channel angular extrusion（ SC-ECAE） is a novel severe plastic deformation technique that has been developed to produce ultrafine-grain steels. Instead of external forces being exerted on specime...Semicontinuous equal-channel angular extrusion（ SC-ECAE） is a novel severe plastic deformation technique that has been developed to produce ultrafine-grain steels. Instead of external forces being exerted on specimens in the conventional ECAE,driving forces are applied to dies in SC-EACE. The deformation of interstitial-free（ IF） steel w as performed at room temperature,and individual specimens w ere repeatedly processed at various passes. An overall grain size of 0. 55 μm w as achieved after 10 passes. During SC-ECAE,the main textures of IF steel included { 111} ,{ 110} ,{ 112} ,{ 110} ,and { 110} At an early stage,increasing dislocations induce new textures and increase intensity. When the deformation continues,low-angle boundaries are formed betw een dislocation cell bands,w hich cause some dislocation cell bands to change their orientation,and therefore,the intensity of the textures begins to decrease. After more passes,the intensity of textures continues to decrease w ith high-angle boundaries,and the sub-grains in dislocation cell bands continuously increase. The present study reports the evolution of textures during deformation; these w ere examined and characterized using high-resolution electron backscattered diffraction（ EBSD） in a field emission scanning electron microscope. The mechanisms of texture evolution are discussed.展开更多
Catalytic pyrolysis of thermoplastics extracted from waste electrical and electronic equipment （WEEE） was investigated using various fly ash-derived catalysts. The catalysts were prepared from fly ash by a simple me...Catalytic pyrolysis of thermoplastics extracted from waste electrical and electronic equipment （WEEE） was investigated using various fly ash-derived catalysts. The catalysts were prepared from fly ash by a simple method that basically includes a mechanical treatment followed by an acid or a basic activation. The synthesized catalysts were characterized using various analytical techniques. The results showed that not treated fly ash （FA） is characterized by good crystallinity, which in turn is lowered by mechanical and chemical treatment （fly ash after mechanical and acid activation, FAMA） and suppressed almost entirely down to let fly ash become completely amorphous （fly ash al^er mechanical and basic activation FAMB）. Simultaneously, the surface area resulted increased. Subsequently, FA, FAMB and FAMA were used in the pyrolysis of a WEEE plastic sample at 400~C and their performance were compared with thermal pyrolysis at the same temperature. The catalysts principally improve the light oil yield： from 59 wt.% with thermal pyrolysis to 83 wt.% using FAMB. The formation of styrene in the oil is also increased： from 243 mg/g with thermal pyrolysis to 453 mg/g using FAMB. As a result, FAMB proved to be the best catalyst, thus producing also the lowest and the highest amount of char and gas, respectively.展开更多
文摘Semicontinuous equal-channel angular extrusion（ SC-ECAE） is a novel severe plastic deformation technique that has been developed to produce ultrafine-grain steels. Instead of external forces being exerted on specimens in the conventional ECAE,driving forces are applied to dies in SC-EACE. The deformation of interstitial-free（ IF） steel w as performed at room temperature,and individual specimens w ere repeatedly processed at various passes. An overall grain size of 0. 55 μm w as achieved after 10 passes. During SC-ECAE,the main textures of IF steel included { 111} ,{ 110} ,{ 112} ,{ 110} ,and { 110} At an early stage,increasing dislocations induce new textures and increase intensity. When the deformation continues,low-angle boundaries are formed betw een dislocation cell bands,w hich cause some dislocation cell bands to change their orientation,and therefore,the intensity of the textures begins to decrease. After more passes,the intensity of textures continues to decrease w ith high-angle boundaries,and the sub-grains in dislocation cell bands continuously increase. The present study reports the evolution of textures during deformation; these w ere examined and characterized using high-resolution electron backscattered diffraction（ EBSD） in a field emission scanning electron microscope. The mechanisms of texture evolution are discussed.
文摘Catalytic pyrolysis of thermoplastics extracted from waste electrical and electronic equipment （WEEE） was investigated using various fly ash-derived catalysts. The catalysts were prepared from fly ash by a simple method that basically includes a mechanical treatment followed by an acid or a basic activation. The synthesized catalysts were characterized using various analytical techniques. The results showed that not treated fly ash （FA） is characterized by good crystallinity, which in turn is lowered by mechanical and chemical treatment （fly ash after mechanical and acid activation, FAMA） and suppressed almost entirely down to let fly ash become completely amorphous （fly ash al^er mechanical and basic activation FAMB）. Simultaneously, the surface area resulted increased. Subsequently, FA, FAMB and FAMA were used in the pyrolysis of a WEEE plastic sample at 400~C and their performance were compared with thermal pyrolysis at the same temperature. The catalysts principally improve the light oil yield： from 59 wt.% with thermal pyrolysis to 83 wt.% using FAMB. The formation of styrene in the oil is also increased： from 243 mg/g with thermal pyrolysis to 453 mg/g using FAMB. As a result, FAMB proved to be the best catalyst, thus producing also the lowest and the highest amount of char and gas, respectively.
