Thermoplastic Starch Prepared with Different Plasticizers: Relation between Degree of Plasticization and Properties

Ethylene glycol, glycerol, sorbitol, formamide, and urea were used as plasticizers for the preparation of thermoplastic starch（TPS） from corn starch. The properties of TPS were tested by analysis method. The results showed that TPSs were more highly plasticized with amines than alcohols. For the same type of plasticizer, the degree of plasticization decreased as the molecular weight of plasticizer increased. The relationship between plasticization degree and TPS properties was characterized and described by mechanical properties and water absorption. The experimental results showed that when the degree of plasticization increased, the tensile strength decreased and the elongation at breakage and water absorption increased.

Mechanical properties of lattice grid composites

An equivalent continuum method only considering the stretching deformation of struts was used to study the in-plane stiffness and strength of planar lattice grid com- posite materials. The initial yield equations of lattices were deduced. Initial yield surfaces were depicted separately in different 3D and 2D stress spaces. The failure envelope is a polyhedron in 3D spaces and a polygon in 2D spaces. Each plane or line of the failure envelope is corresponding to the yield or buckling of a typical bar row. For lattices with more than three bar rows, subsequent yield of the other bar row after initial yield made the lattice achieve greater limit strength. The importance of the buckling strength of the grids was strengthened while the grids were relative sparse. The integration model of the method was used to study the nonlinear mechanical properties of strain hardening grids. It was shown that the integration equation could accurately model the complete stress-strain curves of the grids within small deformations.

Analysis on plastic properties of reactive powder concrete continuous beams reinforced with GFRP bars

To study the plastic properties of reactive powder concrete continuous beams reinforced with GFRP bars,the calculation programs for moment redistribution coefficients are prepared by using nonlinear analysis methods such as moment-curvature,conjugate beam method and so on. By comparing the test results of existed FRP bars reinforced concrete continuous beams with simulation results,the accuracy of the calculation program is verified. Then 18 simulated GFRP bars reinforced reactive powder concrete continuous beams are selected whose change parameters are reinforcement ratio of mid-span and middle support. Through the nonlinear analysis of simulated beams,moment redistribution coefficients under mid-span concentrated loads,one-third point loads and uniformly distributed loads are obtained respectively. Thus the formula of moment redistribution coefficients is obtained by fitting moment redistribution coefficients and factors. The results show that the reactive powder concrete continuous beams reinforced with GFRP bars have good plastic properties.

ADVANCES IN LIQUID CRYSTALLINE POLYESTERS

Advances have been made in understanding the interactions of composition, molecular weight, liquid crystallinity,orientation, and three-dimensional crystallinity on the properties of injection-molded and melt-spun liquid crystalline polyesters (LCP's). Two classes of potentially low-cost LCP's were compared:(1) semiflexible LCP's prepared from 1,6-hexanediol and the dimethyl ester of either trans-4, 4'stilbenedicarboxylic acid or 4.4 ' biphenyldicarboxylic acid and (2) all-aromatic LCP's prepared from terephthalic acid, 2, 6-naphthalenedicarboxylic acid, the diacetate of hydroquinone, and the acetate of p-hydroxybenzoic acid. The effects of composition on the plastic properties of the 4-component all-aromatic LCP's were determined with the aid of a 3 x 3 factorial statistically designed experiment, the generation of equations with a computer program, and the plotting of three-dimensional figures and contour diagrams. The effects of absolute molecular weight (M_w) on the tensile strengths of the semiflexible LCP's and one of the all-aromatic LCP's having an excellent balance of plastic properties were also compared, and it was observed that the semiflexible LCP's required M_w's about 4 times higher than the all-aromatic LCP to attain a given strength. Persistence lengths and molecular modeling were used to explain these differences.

Ice-and cryogel-soil composites in water-retaining elements in embankment dams constructed in cold regions

There are a number of serious problems connected with building and repairing water-reining elements in embankment dams in cold regions. One of them is the difficulty in finding inexpensive clay materials with the necessary structural properties and using them in the winter. Another is the cracks that appear in the upper part of a dam when the core freezes to the banks, and leakage along the cracks threatens to desWoy the dam. Still another is the process of erosion at the bottom of the core which may occur through fissures in the rock foundation of a dam and in transport constructions. Also, the behaviour of water-retaining elements during eazthquakes is unreliable. All of these problems can be solved by using iceand cryogel-soil composites created by cryotropic gel formation （CGF）. Our laboratory investigations demonstrate that the materials proposed for water-retaining elements have the necessary permeable, plastic, thermophysical, and slrength properties to solve all of these problems. Certain consmactious of water-retaining elements which may prove to be both safe and cost-effective are proposed. However, these iceand cryogel-soil composites need to be field-validated before they are used in dams and transport structures in cold regions.

Thermal stability of retained austenite and mechanical properties of medium-Mn steel during tempering treatment

The thermal stability of retained austenite（RA）and the mechanical properties of the quenched and intercritical annealed 0.1C-5Mn steel with the starting ultrafine lamellar duplex structure of ferrite and retained austenite during tempering within the range from 200 to 500°C were studied by X-ray diffraction（XRD）,transmission electron microscopy（TEM）and tensile testing.The results showed that there was a slight decrease in the RA volume fraction with increasing tempering temperature up to 400°C.This caused a slight increase in the ultimate tensile strength（UTS）and a slight decrease in the total elongation（TE）;thus,the product of UTS to TE（UTS×TE）as high as 31GPa·% was obtained and remained nearly unchanged.However,aportion of the RA began to decompose when tempered at 500°C and thus caused a^35% decrease of the RA fraction and a^16%decrease of the value of UTS×TE.It is concluded that the ultrafine lamellar duplex structure is rather stable and the excellent combination of strength and ductility could be retained with tempering temperature up to 400°C.Thus,thermal processes such as galvanization are feasible for the tested steel provided that their temperatures are not higher than 400°C.

Microstructures and mechanical properties of ferrite-based lightweight steel with different compositions

The microstructures and mechanical properties of ferrite-based lightweight steel with different compositions were investigated by tensile test,scanning electron microscopy（SEM）,transmission electron microscopy（TEM）,X-ray diffraction（XRD）and thermodynamic calculation（TC）.It was shown that the ferrite-based lightweight steels with 5wt.%or 8wt.%Al were basically composed of ferrite,austenite andκ-carbide.As the annealing temperature increased,the content of the austenite in the steel gradually increased,while theκ-carbide gradually decomposed and finally disappeared.The mechanical properties of the steel with 5wt.%Al and 2wt.%Cr,composed of ferrite and Cr7C3carbide at different annealing temperatures,were significantly inferior to those of others.The steel containing 5wt.%Al,annealed at 820°C for 50sthen rapidly cooled to 400°C and held for 180s,can obtain the best product of strength and elongation（PSE）of 31242MPa·%.The austenite stability of the steel is better,and its PSE is higher.In addition,the steel with higher PSE has a more stable instantaneous strain hardening exponent（n value）,which is mainly caused by the effect of transformation induced plasticity（TRIP）.When theκ-carbide or Cr7C3carbide existed in the microstructure of the steel,there was an obvious yield plateau in the tensile curve,while its PSE decreased significantly.

Mechanical Properties and Microstructure Evolution of AA1100 Aluminum Sheet Processed by Accumulative Press Bonding Process

Accumulative press bonding（APB） is a novel variant of severe plastic deformation processes,which is devised to produce materials with ultra-fine grain.In the present work,the mechanical properties and microstructural evolution of AA1100 alloy,which is produced by APB technique,were investigated.The study of the microstructure of AA1100 alloy was performed by optical microscopy.The results revealed that the grain size of the samples decreased to 950 nm after six passes of APB process.The yield strength of AA1100 alloy after six passes of the process increased up to 264 MPa,which is three times higher than that of the as-cast material（89 MPa）.After six passes,microhardness values of AA1100 alloy increased from 38 to 61 HV.Furthermore,the results showed that the behavior of variations in mechanical properties is in accordance with the microstructural changes and it can be justified by using the Hall-Patch equation.Moreover,the rise in the yield strength can be attributed to the reduction in the grain size leading to the strain hardening.

Tailoring Microstructure and Tribological Properties of Cold Deformed TiZrAlV Alloy by Thermal Treatment

Microstructure evolution and tribological properties of a new Ti Zr Al V alloy have been investigated in the present study. Various microstructures, i.e., equiaxed grain structure, dual-phase lamella structure, and heterogeneous lamellar structure, have been successfully prepared, and the effect of the microstructure on tribological properties was explored by means of cold severe plastic deformation combined with subsequent recrystallization annealing and aging treatments. The special heterogeneous lamellar-structured alloy exhibits a high ultimate tensile strength（~1545 MPa）,reasonable ductility（~7.9%）, and excellent wear resistance as compared with the equiaxed grain-structured and dualphase lamella-structured alloy. The present study demonstrates an alternative route for enhancing the tribological properties of alloys with heterogeneous lamellar structure.

Recent progress in medium-Mn steels made with new designing strategies, a review

After summarizing the relevant researches on the medium Mn steels in references, two new targets on the tensile properties have been defined. One is that both transformation-induced（TRIP） and twinninginduced plasticity（TWIP） could be realized for the steel with a relatively low Mn content, which exhibits the similar tensile properties to the classical TWIP steels with higher Mn content. The other is to achieve ultrahigh ultimate tensile strength（〉1.5 GPa） without sacrificing formability. To achieve these goals,new designing strategies was put forward for compositions and the processing route. In particular, warm rolling was employed instead of the usual hot/cold rolling process because the former can produce a mixture of retained austenite grains with different morphologies and sizes via the partial recrystallization. Consequently, the retained austenite grains have a wide range of mechanic stability so that they can transform to martensite gradually during deformation, leading to enhanced TRIP effect and then improved mechanic properties. Finally, it is succeeded in manufacturing these targeted medium Mn steels in laboratory, some of them even exhibit better tensile properties than our expectation.